SHENZHEN TECHSTAR ELECTRONICS CO.

,LTD

Specification
For
LCD Module
TS12864C-5(V1.0)

MODULE: TS112864C-5(V1.0)
CUSTOMER:

REV DESCRIPTION DATE

1 FIRST ISSUE 20/07/2006

IDW INITIAL DATE

APREPARED BY YJ KUANG 20/07/2006
CHECKED BY
APPROVED BY

CUSTOMER INITIAL DATE

APPROVED BY
 SHENZHEN TECHSTAR ELECTRONICS CO.,LTD
REV DATE CHANGE DETAIL ORIGINATOR REMARKS

1 20/07/2006 FIRST ISSUE YJ KUANG

 TABLE OF CONTENTS

1.0 INTRODUCTION

1.1 FEATURE

2.0 DIMENSIONAL DIAGRAM

3.0 MECHANICAL SPECIFICATIONS

4.0 MAX STANDARD VALUE

5.0 ELECTRICAL CHARACTERISTICS

6.0 OPTICAL CHARACTERISTICS

6.1 OPTICAL MEASUREMENT SYSTEM

6.2 DEFINITION OF θ and Φ

6.3 DEFINITION OF CONTRAST RATIO Cr

6.4 DEFINITION OF OPTICAL RESPONSE TIME

7.0 INTERFACE PIN FUNCTION DESCRIPTION

8.0 BLOCK DIAGRAM

8.1 POWER SUPPLY BLOCK DIAGRAM

9.0 TIMING CHARACTERISTICS

10.0 DISPLAY CONTROL INSTRUCTION

TS12864C-5 LCD Module Specification Ver1.0 3

1.0 INTRODUCTION
This USER’S MANUAL is introduced the outside dimensions, optical characteristics,

electrical characteristics, interface, controller commands, etc. of the custom design LCD

module.

1.1 FEATURE
(1) Display mode: STN ,YG, Positive, Transflective

(2) Display format: 128*64 Dots

(3) Driving method: 1/64 Duty, 1/9 Bias

(4) Viewing direction: 6 o’clock

(5) Control IC: NT7107/NT7108

(6) Interface Input Data : 8-Bit

(7) Back light: LED (YG)

2.0 DIMENSION DIAGRAM

78.0 0.5
76.0 0.3
68.0 0.3
62.0 0.3(V.A) Max15.0
56.27(A.A) MAX8.5
1.6
2.5

8.0 P2.54X(20-1)=48.26

1 20
44.0 0.3(V.A)
38.35(A.A)
64.92 0.3
70.0 0.5

58.0 0.3

128 X 64 DOT

0.44
0.39
0.55

L
4P
0.60

BLOCK DIAGRAM: 2.5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
CS1 CS2 VSS VDD V0 RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 RESET VEE BLA BLK

RTS12864B-5 LCD Module Specification Ver1.0 4

3.0 MECHANICAL SPECIFICATIONS
ITEM STANDARD VALUE UNIT

DOTS 128X-64 -

DOT SIZE 0.39X0.55 mm

DOT PITCH 0.44X0.60 mm

MODULE DIMENSION 78.0(W) × 70.0(H) × 1.6(T) mm

EFFECTIVE DISPLAY AREA 62.0(W) × 44.0(H) mm

4.0 MAX STANDARD VALUE

ITEM SYMBOL MIN. TYPE MAX UNIT

OPERATING TEMPERATURE Top -20 25 70 ℃

STORAGE TEMPERATURE Tst -30 / 80 ℃

INPUT VOLTAGE VI VSS / VDD V

SUPPLY VOLTAGE FOR LOGIC VDD-VSS Vss-0.3 / 7.0 V

SUPPLY VOLTAGE FOR LCD VDD-V0 8 / 15 V

5.0 ELECTRICAL CHARACTERISTICS

TS12864C-5 LCD Module Specification Ver1.0 5

 ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT

SUPPLY VOLTAGE
VDD-VSS Ta = 25 °C 4.5 5.0 5.5 V
FOR LOGIC

SUPPLY VOLTAGE VDD-VO

Ta = 25 °C 9.8 10.5 13.5 V
FOR LCD (VOP)

INPUT HIGH VOL. VIH Ta = 25 °C 2.0 - VDD V

INPUT LOW VOL. VIL Ta = 25 °C VSS - 0.8 V

OUTPUT HIGH VOL. VOH Ta = 25 °C 2.4 - - V

OUTPUT LOW VOL. VOL Ta = 25 °C - - 0.4 V

SUPPLY CURRENT IDD VDD = 3.0V - 100 500 μA

6.0 OPTICAL CHARACTERISTICS

Measurement
No Item Symbol MIN. TYP. MAX. Unit
temperature

1 Contrast Ratio Cr 25℃ 2.60 3.17

Rise time Tr 25℃ 100 120 mS

Response Fall time Tf 25℃ 60 80 mS

2
Time On time Ton 25℃ 150 170 mS

Off time Toff 25℃ 80 120 mS

3 Viewing 6H,Φ=0° θ1 25℃ 55 Deg.

TS12864C-5 LCD Module Specification Ver1.0 6

 Angle 12H,Φ=180 θ2 25℃ 0 Deg.

Φ=90° θ3 25℃ 45 Deg.

Φ=270 θ4 25℃ 45 Deg.

4 Frame Frequency 25℃ 32 76 200 Hz

6.1 OPTICAL MEASUREMENT SYSTEM

6.2 DEFINITION OF θ AND Φ

6.3 DEFINITION OF CONTRAST RATIO Cr

TS12864C-5 LCD Module Specification Ver1.0 7

6.4 DEFINITION OF OPTICAL RESPONSE TIME

7.0 INTERFACE PIN FUNCTION DESCRIPTION

PIN NO SYMBOL FUNCTION

1 CS1 Active High, left chip selection

2 CS2 Active High, right chip selection

3 VSS Ground(0V)

4 VDD Power supply for logic circuit(5V)

5 VO Operating voltage for LCD driving(Variable)

6 H :Data input ; L : Instruction code input

D/I

7 H: Data Read (LCM to MPU) ; L: Data Write (MPU to LCM)

R/W

8 Enable signal.
E

TS12864C-5 LCD Module Specification Ver1.0 8

 Write mode (R/W = L) → data of DB<0:7> is latched at the

falling edge of E.

Read mode (R/W = H) → DB<0:7> appears the reading data

while E is at high leve

9~16 DB0-DB7 Data bus. There state I/O common terminal.

17 RESET Reset Signal

18 VEE Negative voltage(-15V)to LCD

19 BLA Backlight (+5V)

20 BLK Backlight (0V)

8.0 BLOCK DIAGRAM

8
DB0~DB7
RS,R/W,E 3
RESET
CS2 SEGMENT SEGMENT
CS1 DRIVER IC DRIVER IC
5 NT7108 NT7108
VSS
SEG64 SEG64
VDD
VO SEGMENT COM64 LCD PANEL
VEE DRIVER IC
NT7107 128 X 64 DOTS
BLA
BLK LED SIDE LIGHT

8.1 POWER SUPPLY BLOCK DIAGRAM

TS12864C-5 LCD Module Specification Ver1.0 9
9.0 TIMING CHARACTERISTICS

TS12864C-5 LCD Module Specification Ver1.0 10

10.0 Display control instruction
The display control instructions control the internal state of the AX6108. Instruction is received from MPU

to NT7107 for the display control. The following table shows various instructions.

TS12864C-5 LCD Module Specification Ver1.0 11

TS12864C-5 LCD Module Specification Ver1.0 12
TS12864C-5 LCD Module Specification Ver1.0 13