TWS-434 TRANSMITTER

TRANSMI RWS-434 RECEIVER

16.1mm

pin 1 : Vcc

14.5mm

13.5mm
pin 2 : Vcc 43.5mm pin 1 : Gnd
pin 2 : Digital Output
123456 pin 3 : Gnd
pin 3 : Linear Output

10.5mm
pin 4 : Gnd

11.5mm
pin 5 : RF Output
¥i½Õ¹q·P pin 4 : Vcc

NEW !
pin 5 : Vcc
pin 6 : Code Input 1234 5678 pin 6 : Gnd
25.4mm pin 7 : Gnd
2.54mm
pin 8 :Ant ( About 30 - 35 cm )

Frequency 300 - 433MHz

Frequency 300 - 433MHz
Moulation : AM ( Code )
Supply Voltage : 1.5v - 12 v dc
RF Output Power : 8mW Moulation : AM
Supply Voltage : 4.5v - 5.5 v dc
Sensitivity : 3uVrms
Output : Digital & Linear
Symbol Parameter Conditions Min Typ Max Unit Application : Radio Remote Control
Vcc Operating supply voltage 1.5 - 12 V ITot Operating supply voltage - 4.5 -
Icc Peak Current - 5 9 mA V Data Data Out Data = +200 uA ( High )I Vcc-0.5 - Vcc V
Vin Input High Voltage IData=100Ua (High) Vcc-0.5 - Vcc V I Data = -10 uA ( Low ) - - 0.3 V
Vii Input Low Voltage IData=0Ua (Low) - - 0.3 V Electrical Characteristics
Fo Absolute Frequency 314.8 315 433.9 MHz Characteristics SYM Min Typ Max Unit
Operation Radio Frequency FC 300 - 434 MHz
Po RF Out Power Into 50Ω -3 0 +2 dBm Sensitivity Pref -106 dBm
Modulation Bandwidth External Encoding - 5 - KHz Channel Width +-500 KHz
Tr Modulation Rise Time - - 100 uS Noise equivalent BW NEB 5 4 KHz
Tf Modulation Fall Time - - 100 uS Baseboard data rate 3 Kb/s
Notes : ( Case Temperature = +25C+/-2C Test Load Impedance = 50 Ω )
Application Circuit: 4-bit RF Receiver using the Holtek HT-12D decoder
Application Circuit: 4-bit RF transmitter using the Holtek HT-12E encoder

Connections: Connections:
1. TWS Gnd to header-pin #3. 1. RWS Gnd to header-pin #1
2. TWS Vcc to header-pin #1. 2. RWS Vcc to header-pin #3
3. TWS Code-Input to header- 3. RWS Digital-Output to header-
pin #2. pin #2

NOTE: /TE can be switched to ground HT-12E encoder data transfers to HT-12D
to provide transmit on button-press. data-pins via RF transmission.

VT-pin transitions from low to high on

More detailed information is available valid reception & address.
from http://www.rentron.com
More detailed information is available
For 8-bit RF remote control substitute from http://www.rentron.com
the HT-12E with HT-640 encoder.
For 8-bit RF remote control, substitute the
Maximum range obtained with 50-ohm HT-12D with HT-648L decoder.
antenna, 35cm in length on TWS &
RWS.
Reynolds Electronics
3101 Eastridge Lane Canon City, Co. 81212 http://www.rentron.com
Tel: (719) 269-3469 Fax: (719) 276-2853 e-mail:[email protected]
 1 2 3 4

SAMPLE +5 VOLT REGULATOR CIRCUIT

LM2940 OR LM7805
+5
D 1 3 D
Vin Vout

GND
+9
+5
+ +
1uF 100uF

DIODE
GND
RELAY
COIL

SAMPLE RELAY DRIVER CIRCUIT FOR RECEIVER

TWS-434
10K
TO DECODER IC OUTPUT

NPN

C C

ANTENNA
1 2 3 4 5 6 RWS-434

ANTENNA
VCC

1 2 3 4 5 6 7 8

VCC

+5
1 18 1 18
A0 VCC A0 VCC
B 2 17 DATA OUT TO TRANSMITTER 2 17 B
A1 DOUT A1 VT
3 16 3 16
A2 OSC2 A2 OSC2
750K 33K
4 15 4 15
A3 OSC1 A3 OSC1
/TE TRANSMIT ENABLE DATA IN FROM RECEIVER MODULE
5 14 5 14
A4 /TE A4 DIN
6 13 6 13
A5 D3 D3 A5 D3 D3 OUTPUT
7 12 7 12
A6 D2 D2 A6 D2 D2 OUTPUT
8 11 8 11
A7 D1 D1 A7 D1 D1 OUTPUT
9 10 9 10
GND D0 D0 GND D0 D0 OUTPUT

HT-12E HT-12D

A Title A

Size Number Revision

Orcad A
Date: 12-Jun-2001 Sheet of
File: C:\CAD\SCHEMATICS.Ddb Drawn By:

1 2 3 4
 1 2 3 4

ENCODER AND DECODER ADDRESS PINS MUST BE AT THE EXACT SAME LOGIC LEVELS FOR THE ENCODER TO CONTROL THE DECODER
THIS ALLOWS A SINGLE TRANSMITTER TO CONTROL MULTIPLE RECEIVERS BY MANIPULATING THE ADDRESS PINS OF THE ENCODER IC TO MATCH THAT OF MULTIPLE RECEIVER DECODER ICS

D D

CONNECT OUTPUT FROM ENCODER IC TO INPUT OF TRANSMITTER CONNECT OUTPUT FROM RECEIVER TO INPUT OF DECODER IC

OUTPUT TO TRANSMITTER
DATA INPUT FROM RECEIVER

8-BIT TRANSMITTER 8-BIT RECEIVER

VCC VCC
D0
1 24 1 24
D1 VCC D1 OUTPUT D1 VCC
D1
2 23 2 23
D2 D0 D2 OUTPUT D2 D0 DO OUTPUT
VCC D2
3 22 3 22
C D3 A9 D3 OUTPUT D3 A9 C
D3
4 21 4 21
D4 A8 D4 OUTPUT D4 A8
D4
5 20 5 20
D5 A7 D5 OUTPUT D5 A7
D5
6 19 6 19
D6 A6 D6 OUTPUT D6 A6
D6
7 18 7 18
D7 A5 D8 OUTPUT D7 A5
VCC D7
8 17 8 17
DOUT A4 VALID TRANSMIT OUTPUT VT A4
9 16 9 16
TE A3 DIN A3
TRANSMIT ENABLE 10 15 10 15
OSC1 A2 OSC1 A2
390K 11 14 390K 11 14
OSC2 A1 OSC2 A1
12 13 12 13
GND A0 GND A0
B B
HT-640 HT-648L OR HT-658

VCC

SUBSTITUTE MOTOR FOR OTHER LOAD TYPES AS NECESSARY

MOTOR

DRIVE CIRCUIT, 1 = ON, 0 = OFF

NPN
1N4148

RELAY
TO DECODER OUTPUT
4.7K
A Title A
8-Bit Encoder/Decoder Circuits
VCC
Size Number Revision
Orcad A
Date: 12-Jun-2001 Sheet of
File: C:\CAD\SCHEMATICS.Ddb Drawn By:

1 2 3 4