Scribd
Upload
141 views1 page

Diameters Inter

The document outlines diameter tolerances and minimum increases for enamelled round winding wires in three grades. It specifies the nominal conductor diameter, tolerance range, and minimum/maximum diameters for each grade. Higher grades have tighter tolerances and larger minimum diameter increases compared to the nominal size. The tolerances and increases ensure the proper functioning and insulation of winding wires in electrical applications.

Uploaded by

seenudesign
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
141 views1 page

Diameters Inter

The document outlines diameter tolerances and minimum increases for enamelled round winding wires in three grades. It specifies the nominal conductor diameter, tolerance range, and minimum/maximum diameters for each grade. Higher grades have tighter tolerances and larger minimum diameter increases compared to the nominal size. The tolerances and increases ensure the proper functioning and insulation of winding wires in electrical applications.

Uploaded by

seenudesign
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

DIAMETERS AND INCREASE IN DIAMETERS OF

ENAMELLED ROUND WINDING WIRES


(METRIC INTERMEDIATE SIZES)
(BASIS : IS 13730-0-1)
Conductor Conductor
Diameter Tolerance Grade 1 Grade 2 Grade 3
(mm) (mm) Minimum Maximum Minimum Maximum Minimum Maximum
Increase overall dia increase overall dia increase overall dia
(mm) (mm) (mm) (mm) (mm) (mm)
0.043 - - 0.052 - 0.058 - -
0.048 - - 0.059 - 0.065 - -
0.053 - - 0.064 - 0.070 - -
0.060 - - 0.072 - 0.079 - -
0.067 0.003 0.007 0.080 0.012 0.088 0.018 -
0.075 0.003 0.007 0.089 0.014 0.095 0.020 0.102
0.085 0.003 0.008 0.100 0.015 0.107 0.022 0.114
0.095 0.003 0.008 0.111 0.016 0.119 0.023 0.126
0.106 0.003 0.009 0.123 0.017 0.132 0.026 0.140
0.118 0.003 0.010 0.136 0.019 0.145 0.028 0.154
0.132 0.003 0.011 0.152 0.021 0.162 0.030 0.171
0.150 0.003 0.012 0.171 0.023 0.182 0.033 0.193
0.170 0.003 0.013 0.194 0.025 0.205 0.036 0.217
0.190 0.003 0.014 0.216 0.027 0.228 0.039 0.240
0.212 0.003 0.015 0.240 0.029 0.254 0.043 0.268
0.236 0.004 0.017 0.267 0.032 0.283 0.048 0.298
0.265 0.004 0.018 0.297 0.033 0.314 0.050 0.330
0.300 0.004 0.019 0.334 0.035 0.352 0.053 0.369
0.335 0.004 0.020 0.372 0.038 0.391 0.057 0.408
0.375 0.005 0.021 0.414 0.040 0.434 0.060 0.453
0.425 0.005 0.022 0.466 0.042 0.488 0.064 0.508
0.475 0.005 0.024 0.519 0.045 0.541 0.067 0.562
0.530 0.006 0.025 0.576 0.047 0.600 0.071 0.623
0.600 0.006 0.027 0.649 0.050 0.674 0.075 0.698
0.670 0.007 0.028 0.722 0.053 0.749 0.080 0.774
0.750 0.008 0.030 0.805 0.056 0.834 0.085 0.861
0.850 0.009 0.032 0.909 0.060 0.939 0.090 0.968
0.950 0.010 0.034 1.012 0.063 1.044 0.095 1.074
1.060 0.011 0.034 1.124 0.065 1.157 0.098 1.118
1.180 0.012 0.035 1.246 0.067 1.279 0.100 1.311
1.320 0.013 0.036 1.388 0.069 1.422 0.103 1.455
1.500 0.015 0.038 1.570 0.071 1.606 0.107 1.640
1.700 0.017 0.039 1.772 0.073 1.809 0.110 1.844
1.900 0.019 0.040 1.974 0.075 2.012 0.113 2.048
2.120 0.021 0.041 2.196 0.077 2.235 0.116 2.272
2.360 0.024 0.042 2.438 0.079 2.478 0.119 2.516
2.650 0.027 0.043 2.730 0.081 2.772 0.123 2.811
3.000 0.030 0.045 3.083 0.084 3.126 0.127 3.166
3.350 0.034 0.046 3.435 0.086 3.479 0.130 3.521
3.750 0.038 0.047 3.838 0.089 3.883 0.134 3.926
4.250 0.043 0.049 4.341 0.092 4.387 0.138 4.431
4.750 0.048 0.050 4.843 0.094 4.891 0.142 4.936
Note: For intermediate conductor diameters the minimum increase figure corresponding to the next largest nominal conductor
diameter shall be taken.

You might also like