Student Project

Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

Student Project 1
Create different components of the Double Bearing assembly and then assemble them as
shown in Figure 1. Figure 2 shows the exploded view of the assembly. The dimensions of
various components are given in Figure 3 to Figure 7.

Figure 1 Double Bearing assembly

Figure 2 Exploded view of the Double Bearing assembly

 2 Student Projects
Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

Figure 3 Top view of the Cap Figure 5 Top view of the Base

Figure 4 Front view of the Cap Figure 6 Front view of the Base

Figure 7 Dimensions of the Bushing and the Bolt

Student Projects 3

Student Project 2
In this tutorial you will create all the components of the Wheel Support assembly and then
assemble them as shown in Figure 8. The exploded view of the assembly is shown in Figure 9.

Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

The dimensions of the components are shown in Figure 10, to Figure 14.

Figure 8 Wheel Support assembly

Figure 9 Exploded view of the Wheel Support assembly

 4 Student Projects
Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

Figure 10 Dimensions of the Base Figure 11 Dimensions of the Support

Figure 12 Front view of the Wheel Figure 13 Sectioned side view of the Wheel

Figure 14 Dimensions of the Shoulder Screw, Bolt, Nut, Bushing,

and Washer
Student Projects 5

Student Project 3
Create the components of the Drill Press Vice assembly and then assemble them, as shown in
Figures 15 and 16. The dimensions for the components are shown in Figures 17 through 22.

Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

You will use the bottom-up approach for creating this assembly.

Figure 15 Drill Press Vice assembly

Figure 16 Drill Press Vice assembly

 6 Student Projects
Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

Figure 17 Dimensions of the Clamp Screw, the Figure 18 Dimensions of the Jaw Face, the Cap
Handle Stop, and the Clamp Screw Handle Screw, and the Safety Handle

Figure 19 Top view of the Base Figure 21 Top view of the Movable Jaw

Figure 20 Front view of the Base Figure 22 Front view of the Movable Jaw
Student Projects 7

Student Project 4
Create the components of the Pipe Vice assembly shown in Figures 23 and 24. The dimensions
of the components are shown in Figures 25 and 26. You will use the bottom-up approach for

Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

creating this assembly.

Figure 23 Pipe Vice assembly

Figure 24 Exploded view of the Pipe Vice assembly

 8 Student Projects
Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

Figure 25 Dimensions of the Base

Figure 26 Dimensions of the other components

Student Projects 9

Student Project 5
Create the components of the Butterfly Valve assembly shown in Figures 27 and 28. The
dimensions of the components are shown in Figures 29 and 37. Use the bottom-up approach

Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

for creating this assembly.

Figure 27 Butterfly Valve assembly Figure 28 Inside view of the Butterfly Valve

Figure 29 Solid model of the Body Figure 30 Top view of the Body

Figure 31 Left-side view of the Body Figure 32 Sectioned front view of the Body
 10 Student Projects
Evaluation Chapters. Do not copy. Logon to www.cadcim.com for more information

Figure 33 Top view of the Arm Figure 35 Dimensions of the Shaft

Figure 34 Sectioned front view of the Arm Figure 36 Dimensions of the Retainer

Figure 37 Dimensions of the Plate, Nut, and Screw