Gerber D200 - Users - Manual

1
Introduction
The Dimension 200 is a router/engraver for three-dimensional

signage created for use with the GRAPHIX ADVANTAGE or
other computer systems along with ART Path software.
The ART Path Software Option allows the GRAPHIX

ADVANTAGE to fully control the routing operation, enabling
you to send jobs directly from ART Path on the GRAPHIX
ADVANTAGE through the ADVANTAGE Router Control
(ARC) station.
The Dimension 200 can cut designs from a variety of materials, as

well as draw all types of text or graphics. In addition, the
Dimension 200 is an excellent solution for creating ADA-
compliant (Americans with Disabilities Act) signage.
Warning: THE DIMENSION 200 IS A COMPUTER-

CONTROLLED MACHINE TOOL AND SHOULD BE
OPERATED ONLY BY TRAINED OPERATORS. THE SAFETY
GUIDELINES IN THIS MANUAL MUST BE FOLLOWED AT
ALL TIMES TO AVOID RISK OF INJURY.
Manual Contents
This manual provides installation, operation, and maintenance
procedures as well as safety guidelines for the Dimension 200.
Covering the basic information needed for using the Dimension
200, it is arranged as follows:
Router requirements and package contents

Stand assembly instructions
Router and optional equipment installation instructions
Safety guidelines
Principles of operation
System preparation and use
2 Dimension 200
Cleaning and maintenance procedures

Recommended feed rates for various materials (card)
Conventions
The following conventions are used in this manual:
Note: A note contains important information which could affect

successful completion of a task.
CAUTION: A caution statement contains information which, if not

observed, could result in damage to the equipment.
WARNING: A warning statement contains information which, if

not observed, could result in personal injury.
Customer Support

If you require assistance installing or operating your Dimension
200, contact your Gerber distributor or the Router Support Group at
800-336-1698 (USA and Canada) or fax at 203-290-5568.
If possible, please use a phone that is close to your GRAPHIX

ADVANTAGE system and have the following information
available before calling:
MS-DOSand Microsoft Windows version numbers

GSP System ID number
System serial number
GRAPHIX ADVANTAGE, Windows, MS-DOS, and hardware
utilities disks
GRAPHIX ADVANTAGE, Windows, and MS-DOS user
manuals
3
Router Requirements
This section discusses the work space, equipment, and electrical

requirements for the Dimension 200 router system.
Work Space Requirements

Warning: THERE MUST BE SUFFICIENT SPACE PROVIDED
IN THE PRODUCTION AREA AROUND THE ROUTER FOR
MATERIAL STORAGE AND SAFE ACCESS FROM ALL
SIDES.
A 3-ft. clearance on all sides of the router stand is the

recommended minimum work area. In addition, all equipment
should be kept reasonably close together. The T-Vac blower
must be located close to the rear of the table.
CAUTION: Do not place a router in a damp work area. The

operating environment should fall within a temperature range
between 32 - 99°°F (0 and 37 C) and within a relative humidity
o
range between 0 and 70%.
Equipment Requirements
ROUTER STAND
A 48 in. square table or stand (with 3-ft. clearance on all sides, or

more if the paneling feature is used) is needed. If the stand is not
used, the table must be a heavy duty table able to support 300 lbs.
ELECTRICAL BOX
Gerber recommends placing the electrical box on the table beside

the unit or under the table. The power switch must be easily
accessible. Do not set the box directly on concrete floors because
of condensation potential. The electrical box must also be
protected from any coolant.
4 Dimension 200
HIGH FREQUENCY SPINDLE OPTION AND SPEED CONTROLLER
The Speed Controller is used only with the High Frequency

Spindle Option. Mount the Speed Controller vertically a
minimum of 3 ft. away from the system, with the controls easily
accessible. Do not set the Speed Controller directly on concrete
floors because of condensation potential. The Speed Controller
must also be protected from coolant.
MIST COOLANT COMPRESSED AIR
The optional Mist Coolant System requires 30-100 psi of

compressed air. The compressor is purchased separately.
CHIP REMOVAL SYSTEM
The Chip Removal System requires a wet/dry shop vacuum with

a 2 1/2" hose diameter to attach to the Chip Removal System.
T-VAC VACUUM SYSTEM (FACTORY-INSTALLED)
The optional T-Vac Vacuum System requires a vacuum blower

and filter (purchased and installed separately) and a dedicated
line installed by a licensed industrial electrician. The vacuum
filter must be placed directly under the rear of the router table,
with the vacuum blower nearby. To obtain additional
information on the vacuum blower, please contact your
authorized Gerber distributor.
Electrical Requirements
The Dimension 200 has specific power requirements which must
be supplied for the system to work properly. Gerber recommends
that all power requirements be installed by a licensed industrial
electrician.
Note: The High Frequency Spindle Speed Controller and T-Vac

Vacuum System electrical service MUST be installed by a licensed
industrial electrician.
Router Requirements 5
Requirements are as follows:
Electrical Box:
Domestic systems: 200, 208, 220, 230, or 250V AC, 30 amp, 60
Hz, single phase, dedicated line.
NEMA Reference X
3-POLE, 4-WIRE
G W
Receptacle: L14-30R
Plug: L14-30P
Y
Neutral
Export systems: 200, 208, 220, 230, or 250V AC, 20 amp, 50

Hz, single phase, dedicated line.
NEMA Reference X
3-POLE, 4-WIRE
Receptacle: L14-20R G W
Plug: L14-20P
Y
Neutral, not connected
T-Vac Vacuum System:

220V AC, 10 amp, 50/60 Hz, single phase, dedicated line. The
plug and receptacle will be determined by the licensed
industrial electrician at the time of installation.
220V AC, 10 amp, 50/60 Hz, three-phase, dedicated line. The
plug and receptacle will be determined by the licensed
industrial electrician at the time of installation.
6 Dimension 200
Speed Controller:
200-240V AC ±10%, 20 amp, 50/60 Hz, single phase,
dedicated line.
NEMA Reference
2-POLE, 3-WIRE
Receptacle: 6-15R
Plug: 6-15P
GROUND
Note: If the High Frequency Spindle Option is purchased, a licensed

industrial electrician must install a dedicated power line for the Speed
Controller. Instructions for this installation are supplied separately.
Router Package Contents

Contents of the large shipping crate for the Dimension 200 are
listed below. Check each part against the list and inspect all parts
for any damage which may have occurred during shipping.
WARNING: Do not attempt to assemble and install the

Dimension 200 without adequate assistance. Though small, the
router table is heavy. At least four people are needed to move
the Dimension 200.
caution: BE EXTREMELY CAREFUL WHEN UNPACKING

THE DIMENSION 200 SO AS NOT TO DAMAGE THE
EQUIPMENT.
Crate:
1 ADVANTAGE Router Control (ARC) Station

1 Electrical Box
1 Dimension 200 Router Table
1 Table Stand Kit
1 Small components box
1 Mist Coolant System (optional)
1 Engraver System (optional for the Dimension 200, standard
for the Dimension 200E)
1 Engraver Vacuum System (optional for the Dimension 200,
standard for the Dimension 200E)
1 8' x 2 1/2" diameter Chip Removal System hose
1 20' braided copper ground strap (may be assembled inside the
Chip Removal System vacuum hose)
1 7' x 2" diameter hose for the T-Vac Vacuum System (optional)
1 T-Vac filter and blower fitting (optional)
2 Hose clamps (optional)
1 Training video
1 ADA material sample
1 Tool Kit
8 Dimension 200
Small Components Box:

1 ARC station power supply
1 Ground strap with connectors and instructions
1 Power cord for the ARC station power supply
1 100' 9-pin to 25-pin RS-232 cable
1 8' 37-pin cable
1 Owner's Guide
1 Warranty
Stand Kit:
4 Legs
2 Front/Rear Cross Members
2 Side Cross Members
2 Front/Rear Tie Members
2 Side Tie Members
36 M6 Bolts (10 mm)
36 M6 Nuts (10 mm)
8 M8 Nuts (13 mm)
12 M8 Washers
4 M8 Bolts (13 mm)
1 Instruction Illustration
Chip Removal System:

1 Fully Assembled Vacuum Shroud
Mist Coolant System (Option):

1 Mist coolant applicator with gauge, flexible coolant tubing,
screws and washers
1 Hole drilling template
1 Installation and Usage Guide
Tool Kit Contents

Tool Kit contents are listed below and identified in the
illustration. Metric sizes are shown in parentheses.
1 Collet wrench set

1 Collet nut
1 .250" collet (6 mm)
1 .125" router bit sleeve (3 mm)
1 .500" collet
3 .125" Gerber Gold bits (3 mm)
3 .250" Gerber Gold bits (6 mm)
1 .020" profile cutter (engraver type) (6 mm)
1 Table surfacing bit
1 Pen assembly
1 Tool Height Gage
1 Step Height Gage
1 5 mm hex key
4 T-nut assemblies
4 Work clamps
4 Clamp nuts
10 Dimension 200
Note: The contents of your tool kit may vary from the photograph.
11
Router Stand Assembly
Warning: THIS PROCEDURE REQUIRES AT LEAST FOUR

PERSONS TO LIFT THE ROUTER TABLE BECAUSE OF ITS
WEIGHT.
CAUTION: When removing the four foot subassemblies from

the Dimension 200 router table, do not set the table on the
ground. Damage to the undercarriage will occur. Use the
wooden packing materials to block up the router table.
Assemble the Leg Assembly

1. Unpack the router and use the wooden packing materials to
block up the router table.
2. Unscrew and remove the four foot subassemblies from the

bottom of the Dimension 200 router table.
3. Attach one foot subassembly to the bottom of each leg of the

stand (as shown on the next page) using the specified parts.
DO NOT tighten the nuts or install the M8 bolt and washer at
the top of each leg at this time.
Note: The top of each leg has one bolt hole on each outside surface. The
bottom of each leg has three bolt holes on each outside surface. Refer to
the Assembled Stand figure.
12 Dimension 200
LEG ASSEMBLY
Router Stand Assembly 13
Assemble the Stand

1. Attach the front, side, and rear cross members to the legs (as
shown in the Assembled Stand figure) using the specified
parts. Do not yet tighten the nuts.
2. Attach the front, side, and rear tie members to the legs (as
shown in the Assembled Stand figure) using the specified
parts. Do not tighten the nuts at this time.
3. Use a carpenter's square to align all parts of the stand. Hand

tighten all nuts.
Mount the Router Table on the Stand

1. Carefully place the router table on the stand. Align the holes
where the foot subassemblies on the bottom of the router table
were with the holes in the top of the legs.
2. Secure the router table to the stand with the M8 bolts and
washers as shown in Leg Assembly figure. Use a wrench to
tighten all nuts on the stand assembly.
Level the Stand and Router Table

1. Use the foot subassemblies to level the stand and router table.
Note: It may be easier to screw the nuts up or down on the foot

subassembly if someone assists you by slightly lifting the router
table to take some of the weight off the foot subassembly.
14 Dimension 200
ASSEMBLED STAND
2. To lower a foot subassembly, use a 13 mm wrench to loosen
the top nut inside the leg frame. When the foot is lowered
sufficiently, tighten the bottom nut against the bottom of the
leg frame.
3. To raise a foot subassembly, use a 13 mm wrench to loosen the

bottom nut on the bottom of the leg frame. When the foot is
raised sufficiently, tighten the top nut inside the leg frame.
15
Router Installation Procedure
Before You Begin

WARNING: Turn OFF power to the GRAPHIX ADVANTAGE
and unplug the system from the outlet. DO NOT plug in power
until instructed to do so.
WARNING: Turn OFF and unplug any lettering systems or

plotters connected to the GRAPHIX ADVANTAGE.
WARNING: THE MAIN POWER BREAKER SWITCH ON

THE FRONT PANEL OF THE ELECTRICAL BOX MUST BE
OFF (POINTING DOWN). THE ROUTER MOTOR SWITCH
(LOCATED ON THE ROUTER MOTOR) MUST BE OFF.
Note: Should problems occur while you install the hardware to your
system, contact the Router Support Group at 800-336-1698 (USA and
Canada) or fax at 203-290-5568.
Power Off Check
The main power breaker switch on the front panel of the

electrical box must be OFF (pointing down).
16 Dimension 200
ARC Station
Connect Power Supply to ARC Station

1. Plug the single-pronged end of the ARC station power cord
into the port labeled R831 on the ARC station (the other end
already connects to the power supply box). See the above
illustration.
2. Locate the power cord and plug the three-slotted end into the
power supply box.
3. Plug the three-pronged end of the power cord into either

receptacle labeled ARC STATION/ACCESSORY on the back of
the electrical box.
Connect Router Table to ARC Station

1. Plug the 14-pin round X and Y limit switch connector from the
router table into the receptacle labeled R892 on the ARC
station. (See the illustration above.)
Connect Electrical Box to ARC Station

1. Plug one end of the 37-pin to 37-pin cable into the receptacle
labeled R830 on the ARC station. Tighten the screws.
2. Plug the other end into the receptacle labeled R846 on the
electrical box. Tighten the screws.
Router Installation Procedure 17
Connect Electrical Box to Router Table

1. Plug the 3-pronged power cord from the router table into the
receptacle labeled R849 on the electrical box.
2. Connect the cable labeled P856 (X motor cable bundled with

the Y and Z motor cables on the router table) to the receptacle
labeled R856X.
3. Connect the cable labeled P857 (Y motor) to the receptacle

labeled R857Y.
4. Connect the cable labeled P858 (Z motor) to the receptacle

labeled R858Z.
Electrical Box
18 Dimension 200
Connect Chip Removal System

The Chip Removal System helps keep the work area clean during
the routing operation. In addition, its pressure foot provides
downward force to keep the workpiece from lifting due to forces
exerted by the routing bit. The pressure foot pad rests on the
workpiece and slides easily over the workpiece surface, while the
tool bit extends through an opening in the pressure foot pad.
Two pads are supplied, one with a 1.5" (38 mm) opening for
normal use, and one with a 0.4" (10 mm) diameter opening for
cutting very small pieces. The 1.5" diameter opening pad, which is
installed at the factory, is used for the mat milling procedure. The
0.4" diameter opening pad is included the tool kit.
A heavy duty wet/dry shop vacuum is required and is not

supplied with the router system. A 2 1/2" (64 mm) diameter hose
and all necessary fittings are provided with the Dimension 200.
INSTALLING THE CHIP REMOVAL SYSTEM
WARNING: BEFORE INSTALLING THE CHIP REMOVAL

SYSTEM, UNPLUG THE ELECTRICAL BOX FROM ITS
POWER SOURCE.
WARNING: SCRAP CHIPS GENERATED BY CUTTING

CREATE STATIC CHARGES WHICH CAN BE HARMFUL TO
THE OPERATOR AS WELL AS MACHINERY COMPONENTS.
A PROPERLY INSTALLED GROUND STRAP CABLE (ALSO
CALLED STATIC DRAIN WIRE) REDUCES THE CHANCES
OF STATIC SHOCK HAZARD. THE GROUND STRAP
CABLE IS ALREADY INSTALLED IN THE VACUUM HOSE
SUPPLIED WITH THE SYSTEM. YOU MUST CONNECT IT
TO THE ELECTRICAL BOX.
To install the vacuum shroud
The vacuum shroud is installed by Gerber. Should you need to

reinstall it, follow the procedure below.
1. Align the screw holes on the vacuum shroud with the screw
holes in the carriage sidewalls.
2. Insert and tighten the screws.
To attach the vacuum hose
1. Attach the vacuum hose onto the pressure foot of the

Dimension 200. (One end of the ground strap cable is already
connected at this end in the interior of the hose.)
2. Lead the vacuum hose and the ground strap which extends
from the end of the vacuum hose to the electrical box. Make
sure that there is ample slack on the strap to comfortably
connect in the next procedure.
20 Dimension 200
3. Now lead the vacuum hose and ground strap to the shop
vacuum canister, inserting some of the ground strap into the
canister.
4. Make sure that some of the ground strap still extends from the
vacuum hose and that there is enough slack on the ground
strap. (The ground strap goes in and comes back out of the
canister to connect to the electrical box in the next procedure.)
Connect the Ground Strap Cables

Ground strap cables are static protection devices that reduce the
risk of static electricity damage to the router system's integrated
circuitry. The Dimension 200 comes equipped with three ground
strap cables which connect as follows:
ARC station to the electrical box
foot mount block on the Dimension 200 router table to the

electrical box
vacuum hose pressure foot to the electrical box.
All three ground strap cables must connect at the same point on
the electrical box. Both ends of all ground strap cables must be
securely fastened to ensure a reliable ground connection.
To connect the ground strap cable at the router table
1. At the left rear of the Dimension 200 router table, remove the
left capscrew that secures the foot mount block to the router
bed.
2. Locate the ground strap cable (recognizable by the yellow ring

lug) fastened to the limit switch and motor cables.
3. Insert the capscrew through the ground strap ring lug and
reinstall.
4. Securely tighten the capscrew to ensure a reliable ground

connection.
To connect the ground strap cable at the ARC station
1. Looking at the ARC station from the back, remove the screw
located on the right side near the back. (In some models, the
screw may instead be located underneath the rear of the ARC
station.)
2. Place the ground strap ring lug over the removed screw.
3. Place the star washer over the screw.
4. Reinstall the screw into the side of the ARC station and
tighten securely.
5. Use the tie wraps supplied to fasten the ground strap cable to
the 37-pin interface cable.
To connect the ground strap cable at the vacuum shroud
Note: The ground strap is already connected to the vacuum shroud.
To connect all ground strap cables to the electrical box
1. Looking at the rear of the electrical box, remove the screw

located on the right side of the electrical box near the attention
label (triangle with an exclamation point).
2. Insert the removed screw through the ring lug of all three
ground strap cables (from the Dimension 200 router table, the
ARC station, and the vacuum shroud).
3. Place one star washer over the screw.
4. Reinstall the screw into the side of the electrical box. To ensure
a reliable connection, tighten the screw securely.
5. Coil up any excess ground strap cable extending from the

vacuum hose and place it inside the reservoir of the shop
vacuum canister.
6. Insert the end of the vacuum hose into the receptacle on the
side of the shop vacuum canister.
22 Dimension 200
Connect GRAPHIX ADVANTAGE to ARC Station

1. Plug the 9-pin D-connector of the RS-232 cable into the port
labeled PLOTTER or COM at the rear of the GRAPHIX
ADVANTAGE. Carefully align all pins and press all the way
in.
2. Tighten the connector thumb screws to secure the cable to the

system.
3. Plug the 25-pin D-connector into the receptacle labeled R829

on the ARC station (see the illustration on page 16). Tighten
the thumb screws.
Power Connections
1. Plug the power cord from the electrical box into an
appropriately grounded outlet.
2. If necessary, plug in the router motor power cord into the

receptacle, as shown.
3. Plug the shop vacuum into the duplex receptacle on the

electrical box labeled SHOP VAC/BLOWER.
4. Turn ON power at the electrical box.

5. Turn ON power at the GRAPHIX ADVANTAGE system.
The ARC station displays the message SLEW TO THE POINT

OF ORIENTATION in the display panel after performing
power-up diagnostics. The router system is now ready to
operate. Refer to the section on setting up the ARC station
later in this chapter.
6. Turn ON the router motor power switch when ready to cut.
Set Up the ARC Station

The ARC station can support several different routers. When you
first install your system, follow the procedure below to configure
the ARC station for the Dimension 200. (See page 39 for an
illustration of the front panel of the ARC station.)
1. With the main power switch off on the electrical box, press
and hold down the RESET and UP arrow keys on the ARC
station.
2. While holding these keys down, turn the main power switch
on.
3. Release the ARC station keys after the second beep. The
SYSTEM: message appears.
4. Press SELECT.
5. Press the left or right arrow key until DIMENSION 200 is

displayed.
6. Press SELECT.
7. LIMIT SWITCH displays. (Gerber recommends that the limit

switch be set to ON.)
8. Press SELECT.
24 Dimension 200
Below is an illustration of the basic Dimension 200 system and its peripherals
to assist you in installing and checking the connections. The illustration does
not depict the actual connections or placement of the equipment.
25
Optional Equipment Installation
This section addresses the installation of optional equipment for

the Dimension 200: the Mist Coolant System, the T-Vac Vacuum
System, High Frequency Spindle and Speed Controller, and the
Engraver and vacuum.
Mist Coolant System

The Mist Coolant System option is used to cool and lubricate the
cutting tool as it cuts metals such as aluminum or brass. It is not
intended for use with non-metallic materials such as wood or
plastic.
The Mist Coolant System is equipped with an 8½ oz. coolant

reservoir that can be filled under pressure with no need to
disconnect air input or stop the system. The coolant drip rate is
easily adjustable from one drop every six minutes to 30 drops per
minute.
The Mist Coolant System requires 30-100 psi of compressed air.

The compressor is purchased separately.
The Mist Coolant System is designed to be used with Gerber Cool

coolant, a high performance spray lubricant available from Gerber
Scientific Products, Inc. Gerber Cool is a non-toxic, biodegradable
coolant custom-formulated for Gerber routers. It meets all FDA
and USDA requirements for use in areas with incidental food
contact and will not harm the environment.
Note: The Mist Coolant System cannot be used at the same time as the
Chip Removal System or the Engraving Option.
26 Dimension 200
INSTALLING THE MIST COOLANT SYSTEM
WARNING: Turn off the GRAPHIX ADVANTAGE and

unplug the Dimension 200 from the AC outlet before installing
the Mist Coolant System to avoid possible electrical shock.
1. Remove the top two screws from the Dimension 200 right end
plate on the right end of the beam when viewed from the
front.
2. Insert these screws through the top hole of each hanging

bracket, reinsert into the end plate, and finger tighten.
3. Align the standoffs on the hanging brackets with the semi-

circular openings in the sides of the mist coolant system.
4. Insert one M4 x 50 mm Phillips panhead screw with flat and

lock washers through semi-circular openings in the mist
coolant reservoir into each threaded standoff in the hanging
brackets. Tighten the hanging bracket and the mist coolant
mounting screws.
5. Cut out the hole drilling template provided in the option kit,
fold the top edge along the fold line, and hold the template
against the left side of the carriage with the folded portion on
top of the carriage wall and the right edge along the front
edge of the carriage wall.
6. Drill a 1/4" hole in the carriage wall where indicated by the

template.
7. Insert the socket head capscrew through the M6 flat washer

and through the carriage wall from the right and into the
nozzle coupling mounting block on the outside of the carriage
wall. Tighten using a 5mm Allen wrench.
8. Run the coolant hose from the reservoir along the cable
harness in the cable trough at the back of the beam. Run the
coolant hose along the entire length of the cable harness, then
across the beam to the X carriage. This will prevent the hose
from stretching as the carriage moves. Run the hose to the left
Optional Equipment Installation 27
side of the carriage when viewed from the front. See the
illustration at right.
28 Dimension 200
The illustration below shows the Dimension 200 carriage with the optional
High Frequency Spindle Motor installed (on the upper left) and Mist Coolant
Option components (on the lower right).
9. Attach the two tie mounts on top of the carriage (as shown in
the illustration on the previous page) and secure the hose.
10. Use the tie wraps to secure the hose to the cable harness in the
cable trough. Place a tie wrap about every 8" along the cable.
Tie the wraps firmly but not so tightly that coolant flow is
restricted.
11. Insert the barb fitting on the air line intake and connect the air
line.
12. Insert the quick-disconnect fitting to the opposite end of the

air line and connect to the compressor.
13. Turn on the Dimension 200. Make sure the coolant hose
travels smoothly in the cable trough by slewing the carriage
from one end of the beam to the other. The coolant hose must
not stretch as the carriage moves.
T-Vac Vacuum System

The optional T-Vac Vacuum System uses vacuum to hold down a
workpiece easily and securely on the router table. Depending on
the material and the job, vacuum hold-down may be used with
adhesive and sacrificial material.
T-Vac requires a vacuum blower, filter, and relief valve purchased

separately. The blower, filter, and relief valve must be connected
to the router table. Hose and necessary attachment fittings are
supplied with the router table.
To install the T-Vac Vacuum System
1. Place the filter directly below the intake opening at the rear of
the router table.
2. Position the blower as close to the filter as possible.

30 Dimension 200
3. Insert the 2" diameter hose supplied in the kit on the intake
opening on the table and secure with a hose clamp.
4. Insert the 2" adapters supplied in the kit on the reducing tee as
shown above.
5. Insert the 1.5" adapter in the relief valve.
6. Install the relief valve on the reducing tee as shown above.
7. Cut the hose to fit in a straight line between the manifold

intake opening and the air filter/relief valve.
8. Attach the hose to the air filter/relief valve assembly and

secure with a hose clamp.
9. Attach one end of the remaining hose to the filter exhaust

opening with a 2" barb adapter and secure with a hose clamp.
10. Attach the other end of the hose to the vacuum blower with a
2" barb adapter, cutting the hose as short as possible to
increase the efficiency of the blower. Secure with a hose
clamp.
11. Have a licensed industrial electrician with industrial motor

experience wire the vacuum blower.
Speed Controller System

Refer to the illustration below when installing the Speed
Controller System:
To install the Speed Controller System
1. Plug the AC power cord into a dedicated wall outlet.
2. Plug the Spindle remote ON/OFF cable labeled P894 into the
connector labeled R894 (top) on the back of the electrical box.
3. Plug the Spindle Motor cable into the connector located on the
High Frequency Spindle motor and latch it.
32 Dimension 200
USING THE SPEED CONTROLLER SYSTEM
The Speed Controller System is used to control the spindle speed

of the High Frequency Spindle motor. The thickness and type of
material, as well as the tool selected, determine the correct spindle
speed. The recommended speed for various materials may be
found at the end of this manual.
The speed selection knob located on the Speed Controller selects a

spindle speed as follows:
Knob Spindle Speed

0 0
10 2,800
20 5,600
30 9,400
40 12,200
50 14,000
60 16,800
70 19,600
80 22,400
90 25,200
100 28,000
Note: The Speed Controller System must be installed by a qualified

electrician. Installation instructions are supplied with the speed
controller.
Engraver Vacuum System Option

The optional Engraver Vacuum System is a quiet, conveniently-
sized system used to clean debris from the table and engraving
area.
To assemble the Engraver Vacuum System
1. Remove and discard the plugs from the holes labeled IN and
OUT on the front of the vacuum motor.
2. Thread the long end of the pipe elbow into the "in" receptacle
on the vacuum motor and tighten. Make sure the elbow
points up.
3. Insert the short pipe fitting into the end of the protruding
elbow and tighten.
4. Place the vacuum tank on the short pipe fitting and rotate the
tank to tighten.
5. To securely tighten the entire attached assembly, one person

should hold down the motor while another person turns the
entire assembly until it is tight.
6. Insert the reducer fitting into the hole on top of the vacuum
tank and tighten.
7. Insert the barbed fitting into the reducer fitting and tighten.
8. Slip one end of the hose over the end of the barbed fitting on
top of the tank.
9. Place the assembled vacuum system near the router,

preferably on the right side.
35
Safety Guidelines
Warning: THE DIMENSION 200 IS A HIGH-SPEED

CUTTING MACHINE. ITS USE MAY BE HAZARDOUS IF
YOU DO NOT OBSERVE THE FOLLOWING PRECAUTIONS.
THESE GUIDELINES ARE NECESSARY FOR THE SAFE AND
EFFICIENT OPERATION OF THE DIMENSION 200.
WARNING: DO NOT STORE WET ALUMINUM CHIPS IN A

CLOSED CONTAINER AND DO NOT USE THE VACUUM
HOSE TO CLEAN UP WET ALUMINUM. WET ALUMINUM
PRODUCES HYDROGEN GAS. THIS GAS MAY REACH
EXPLOSIVE CONCENTRATIONS WHEN WET ALUMINUM
CHIPS ARE STORED IN A CLOSED CONTAINER.
1. Only a trained operator should attempt to run the equipment.
2. Wear protective eyewear, such as goggles or safety glasses,

which cover the front and sides of the face.
3. Do not use the router in a damp or wet location.
4. Do not store wet aluminum chips in a closed container.
5. Do not use the vacuum hose to clean up wet aluminum.
6. Stand in front of the ARC station during system operation to

provide easy access to the RESET key and the main power
switch on the electrical box. (This also prevents any clothing
from getting caught in the machine.)
7. Keep the work area clear for easy access to the main power
switch.
8. Unplug or turn off the router motor when changing tools.
9. Tie back or cover long hair.

36 Dimension 200
10. Remove loose jewelry, ties, and loose clothing. Wearing a

long-sleeved shop coat is strongly recommended.
11. Wear ear protection.
12. Keep all personnel at a safe distance from the machine when it
is operating.
13. Carefully secure the workpiece with clamps.
14. Use the proper tool for the material. Do not use small tools
with heavy material.
15. Make a test cut whenever possible to test the tool in the
material.
16. Perform all periodic maintenance procedures on a regular

basis.
37
Operating Principles
Overview
Note: It is essential that you read this section before operating the
Dimension 200. This section introduces the operating principles of the
router system.
The complete Dimension 200 router system consists of these major

components:
the Dimension 200 router table

the electrical box
the ARC station
Text and graphics are cut or drawn by the router after being
prepared for routing by ART Path. During router operation, the
cutting table and clamped workpiece remain stationary. All
operating motion is performed by the router motor, carriage, and
tool.
X, Y, Z Axes
The Dimension 200 has three basic axes of movement:
The X (horizontal) axis is oriented from left to right.

The Y (vertical) axis is oriented from front to back.
The Z (depth) axis is oriented up and down.
When the router cuts a design, the tool moves in the X, Y and Z
axes of movement.
38 Dimension 200
Z Axis
The Z axis of the router is the up and down movement of the tool.
Initializing the Z axis is an essential procedure when using the
Dimension 200. It establishes the location of the tool above the
workpiece at the start of a job.
CAUTION: The Z axis must be set every time the tool or

material is changed, and whenever the operator prepares to cut
or draw. Failure to initialize the Z axis properly will cause the
machine to cut at the wrong depth. This may destroy the
material and cause the tool to cut into the router table.
The Z axis may be positioned by:
the Z INIT function key located on the ARC station keypad

a Z axis adjustment knob located on top of the Z axis motor
the ART Path depth of cut
The workpiece and sacrificial material must be mounted on the

router table when the Z axis is initialized. See the Z INIT portion
of the ARC station section in this manual for instructions on
initializing the Z axis.
Operating Principles 39
Job Home Position

The job home position is the position on the router table which
corresponds to the job 0,0 point or starting position of the job.
The job home position is stored in the ARC station and is
maintained even when power is interrupted.
The job home position (start position) is also controlled by ART

Path. ART Path considers the current tool position to be job home.
The actual job starting position may be modified by a pre-
position (either absolute or relative) set in the ART Path Output
dialog box.
The SET JOB HOME function of the ARC station allows the router
operator to modify the home position either before or after a job
has been received at the ARC station and the job header, material
and tool messages have been displayed.
The job home position of each job is stored when the job starts.
The RETURN HOME function of the ARC station returns the
carriage to the stored job home position. In the event of a power
failure or other job interruption, the operator can use the
RETURN HOME function to return the router carriage easily to
the stored home position. This also simplifies starting multiple
jobs from the same position.
See the “Set Job Home” and “Return Home” descriptions in the
ARC station section of this manual for more information. Also see
the ART Path User Manual for information on job positioning.
40 Dimension 200
Power Switch
The main power switch is located on the front of the electrical
box, encircled by a yellow border. It switches power on and off at
the ARC station. Turn the power on or off here for normal use.
Before turning on the main power switch, make sure that the ARC
station power supply is connected to both the ARC station and
the appropriate grounded outlet on the back of the electrical box.
Emergency Power Switch
The main power switch on the front of the electrical box also
serves as the emergency power switch. Turn off power here for
emergencies.
ROUTER MOTOR POWER SWITCH
The router motor power switch turns the motor on and off. The
router motor has a thumb switch on the top labeled ON and OFF.
WARNING: The router motor must be OFF during vacuum

shroud installation, mist coolant installation, tool changing, Z
axis initialization, or when performing any other functions
around the cutter.
CAUTION: The router motor switch should be off until the job
is ready to begin. DO NOT turn the router motor on when pen
plotting.
1. When the job is ready to begin, turn ON the router motor

power switch.
2. Press the START key to start the job.
Note: There is a delay before the tool begins cutting. This delay gives
the router motor time to come up to full speed before cutting begins, and
the operator time to stop the job if the router motor is not ON.
ARC Station
The Advantage Router Control (ARC) station is the
communication link between the GRAPHIX ADVANTAGE and
the router system. It can do the following:
send and receive messages and commands to and from the

GRAPHIX ADVANTAGE
display messages to the operator
control router motor movements
change feed rates
return the router carriage to the job home position
set motor delay
42 Dimension 200
FRONT PANEL
The front panel of the ARC station consists of a message display

panel and nine function keys:
START/STOP
RESET
Z INIT
SELECT
right, left, up, and down arrow keys.
The ENTER key is not used.
Display Panel
The bottom right of the message display panel may contain

indicators for the operator:
W, w - Alternating uppercase and lowercase indicates that

the router is waiting for a job.
J, j - Alternating uppercase and lowercase indicates that
there is a job ready for routing. Pressing START will begin or
continue processing the job.
I, i - Alternating uppercase and lowercase indicates the job is
incomplete, which occurs when a partial job is sent from ART
Path. Power interruption at the GRAPHIX ADVANTAGE or a
pause status in the Plot Spooler application will cause partial
transmission.
WARNING: WHEN THE INCOMPLETE JOB INDICATOR

(I,I) AND START JOB ARE DISPLAYED, THE ROUTER
CARRIAGE MAY MOVE WITHOUT FURTHER WARNING.
The top right of the message display panel at times may contain
an asterisk (*). When a job is running and the operator presses
the STOP key, the asterisk appears to show that the machine has
received the message and will pause at the next logical point. The
router will resume cutting when the START key is pressed again.
Power-Up Tests
When the power is turned ON, the ARC station performs
diagnostic self-tests, and displays the operating set revision level.
The ARC station requests the operator to slew the router carriage
near the point of orientation, which is the absolute 0,0 point. To
slew to the point of orientation, use the arrow keys to move the
router carriage as far toward the front and to the left as possible.
When the carriage is at 0,0, the carriage will move away from the
limit a preset distance in X and Y. The ORIENTATION message will
appear in the display panel, followed by the STOP READY
message.
If an error occurs:
The system emits a constant audible tone.

Press the RESET key to clear the error and to rerun the failed
test(s).
If the same error recurs or if RAM ERROR, ROM ERROR, or
INTR_ERROR is displayed, contact the Router Support
Department at 800-336-1698 (USA and Canada).
When testing successfully completes, the STOP READY message

displays.
44 Dimension 200
Function Keys
The function keys located on the front panel of the ARC station
perform specific routines. Each function key is discussed
individually in the following pages.
ARROW KEYS
The arrow keys are most frequently used to slew the router
carriage into position. Slewing refers to positioning the X and Y
axes where desired.
The arrow keys are also used to scroll through available choices at
the ARC station after a selection has been made in the Menu
Select mode. See the page in this section on Menu Select mode.
To slew the Dimension 200
To position the tool to the left or right over the router table
surface, press the left or right arrow keys until the desired
placement is reached.
To position the tool forward or backward over the table

surface, press the up or down arrow keys until the desired
placement is reached.
To slew diagonally, press two keys at the same time (left or

right with up or down).
You cannot slew past the table edges if the limit switches have
been set.
START/STOP
This key toggles between the START and STOP modes.
Start Mode
START mode, as shown by a message in the display panel, may

be in one of two states:
START READY - the system is ready to receive a job

START JOB - the system has received a job and is processing it
The following keys are available in START mode:
RESET - immediately aborts router movement and purges the

job
START/STOP - pauses processing the job
Start Ready
WARNING: In START READY mode, the carriage may move

without further warning.
1. While in the STOP READY mode, use the arrow keys to slew
the carriage to the starting location of the job.
2. Press the START/STOP key to display the START READY

message.
The Dimension 200 is now in a “ready” state and the message

remains until the data arrives from the GRAPHIX ADVANTAGE.
The current tool position becomes the start point for the job.
46 Dimension 200
Start Job
When the job data is received, the START JOB message appears,
indicating that the Dimension 200 is in a “run” state. ART Path
sends a header or tool message, the system goes into STOP JOB
mode and instructs the operator to load material. Press
START/STOP again to display the tool assignment. To begin the
job, press START/STOP again.
WARNING: The carriage may move without further warning.
Stop Mode
STOP mode, as shown by a message in the display panel, may be

in one of two states:
STOP READY - the router is in an idle state waiting to receive

data
STOP JOB - the router is in a pause state during a job
The following keys are available in STOP mode:
START/STOP
RESET
Z INIT
SELECT
arrow keys
Stop Ready
In STOP READY, the GRAPHIX ADVANTAGE sends data to the

ARC station. The system beeps when data is received and J, j is
displayed in the lower right corner of the message display panel.
Press the START/STOP key to begin the job.

The carriage can be slewed to establish a start position for the
next job.
The job start position can be changed in the STOP READY mode.
It can also be changed when one of the following occurs:
SET HOME is selected from the menu

the job completes
the operator presses RESET to abort the job and clear it from
the ARC station
the ARC station receives a terminate command from the
GRAPHIX ADVANTAGE Plot Spooler.
Stop Job
If you press the START/STOP key while in the START JOB mode,
the machine enters pause mode and results in the following:
the STOP JOB message appears

no incoming data processes
the job stops at the next logical break point
the tool raises
the router motor turns off
an asterisk appears in the upper right corner of the message
display.
When the router is in pause mode, you can slew the router
carriage for tool changes or other tasks. Press START/STOP to
return the router tool to the position in the job where the operator
paused the system. The job can be resumed without position or
data loss.
48 Dimension 200
Resume Processing
After pausing temporarily, press the START key to resume

processing without position or data loss.
Change Tools
If a tool change is required, follow the steps below:
1. In STOP JOB mode, slew the carriage to a safe tool change

position.
Note: If a tool is changed during a job, the system remembers the

tool position and returns from slew to the appropriate location.
2. Turn OFF the router motor and disconnect the router motor
power cable from the router motor.
3. Change the tool. (See the sections on “Tool Installation” and

“Tool Replacement” in this manual, if necessary.)
4. Initialize the Z axis. (If needed, see the Z INIT function key
explanation in this section of the manual.)
5. Change the Feed Rate parameter, if necessary.
6. Reconnect the router motor power cable and turn ON the

router motor.
7. To avoid hitting clamps, manually slew close to where the job

will resume.
8. Reset the vacuum shroud (lower it back to the material

surface).
9. Press the START/STOP key to continue the job. The carriage

will return to the pause position, then enter STOP JOB mode.
Press START/STOP again to resume the job.
Repeat Job
To repeat a job at the same position as the previous job, before

pressing START/STOP:
1. Press SELECT while in the STOP READY mode to access the

Menu Select mode.
2. Press the right or left arrow key until RETURN HOME appears
in the message box.
3. Press SELECT. The router carriage will move to the job home
position.
4. Press START/STOP to begin processing the job.

50 Dimension 200
RESET
The RESET function key immediately halts the job that is running.
In Start Mode
If in START JOB mode and the operator presses the RESET key:
the tool raises

the carriage X,Y travel stops
current job data from the router and the GRAPHIX
ADVANTAGE clears
the STOP/READY message displays.
In Menu Select Mode
RESET exits the menu without saving changes.
In Other Modes
If in any other mode and the operator presses the RESET key, the
ABORT ??? message appears.
To cancel the job, press the RESET key again.
To continue the job without data loss, press START/STOP.

Z INIT
The Z INIT function key initializes the Z axis tool height above
the work surface. The Z INIT key may be used only when the
STOP JOB or STOP READY message displays. You may use either
the tool height gage or the step height gage for initialization.
CAUTION: The Z axis must be set every time the tool or

material is changed. Failure to initialize the Z axis properly will
make the tool cut into the material at the wrong depth. This may
destroy the material and cause the tool to cut into the router
table.
CAUTION: Do not turn the Z axis knob after the Z axis has
been initialized.
To perform Z Init
1. Place the step height gage on top of the material to be cut. (See
the procedure in this manual for “Using the Step Height
Gage.”)
2. Slew the carriage to position the tool over the gage.
3. Press the Z INIT key. The Z motor is now OFF to allow for
manual adjustment. The Z UNLOCKED message appears.
4. Turn the Z axis knob to lower the tool until it just touches the
surface of the step height gage.
CAUTION: Excessive pressure will cause tool damage.
5. Press Z INIT to raise the tool.
Note: If RESET is pressed, the Z motor locks and the Z INIT

process is exited.
6. Remove the step height gage.

52 Dimension 200
ENTER
This function key is not used in this release. Press SELECT to exit
a selection and store values. Press RESET to exit a selection
without storing values.
SELECT
This function key allows access to the Menu Select mode to set
system parameter values. It is available in STOP mode when the
STOP READY or STOP JOB message is displayed.
Using Select
To access the Menu Select mode, press SELECT while in the STOP
READY or STOP JOB mode.
The choices available are as follows:
Absolute (X,Y):
Set Job Home
Return Home
Feed Rate:
Motor Delay:
Test:
Display:
Default
Note: A colon (:) following a menu selection indicates additional choices

are available when the item is selected. Each menu selection is explained
and contains directions on changing parameters.
To exit the Menu Select mode and return to STOP mode without
changing settings, press RESET.
To make a selection in Menu Select mode
1. Press the right arrow key to scroll forward (right) through the
menu list or press the left arrow key to scroll backward (left)
through the menu list.
2. When the desired menu item appears, press the SELECT key
to display the choices available under the selected menu item
if the item is followed by a colon (:), or to execute the function.
3. Use the arrow keys to display available choices.

54 Dimension 200
ABSOLUTE X,Y:
The Absolute X,Y function displays the exact position of the

router tool relative to the absolute 0,0 position on the router table
established during orientation when the router was turned on.
The Absolute X,Y display allows the operator to position the
router tool with great precision and helps set the job home
position. Each coordinate is precise to three decimal places
(000.000) in inches, two decimal places (0000.00) in mm.
To display the absolute X,Y position
1. Press SELECT while in the STOP READY or STOP JOB mode.
2. Press the right or left arrow key until Absolute (X,Y): appears
in the message box.
3. Press SELECT to display the current position.
X: +000.000 INCH
Y: +000.000 INCH
4. Press any arrow key to move the router carriage. The message
box will display the new coordinate position when the arrow
key(s) are released.
5. Press any key to exit.

SET JOB HOME
The job home position is the point that corresponds to the starting
point of the job. It is the point by which a job is positioned on the
router table. ART Path considers the current tool position to be job
home. The actual job starting position may be modified by a pre-
position (either absolute or relative) set in the ART Path Output
dialog box.
The SET JOB HOME function allows the router operator to

modify the home position after a job has been received at the ARC
station and the job header, material, and tool messages have been
displayed.
The job home position of each job is stored when the job starts.
The RETURN HOME function returns the carriage to the stored
job home position. In the event of a power failure or other job
interruption, the operator can use the RETURN HOME function
to return the router carriage easily to the stored home position.
To place multiple jobs in the same home position on the table, the
operator must use the Return Home parameter prior to sending
the job from the GRAPHIX ADVANTAGE to move the router
carriage to the exact job home position.
Note: If the router carriage hits a clamp or fixture when moving,

position may be lost. Turn power to the system off and on. As instructed
on the message display, reestablish position by using the arrow keys to
move the router carriage to the extreme front, left point (the point of
orientation).
Setting Job Home Position
The tool position when you press START/STOP is the job home
position, unless a job pre-position has been set in the Output
dialog box in ART Path. In that case, the pre-position becomes the
job home position.
You can set job home from the ARC station using the following
procedure, but a job must be in the queue for the job home
position to be stored.
56 Dimension 200
WARNING: Do not use the Set Job Home parameter to reset job
home after cutting has begun. The carriage will move unpredictably
when the job is restarted.
To set job home
1. Slew the carriage to the desired job home position by pressing

the arrow keys. This position will be stored as job home when
you press START/STOP.
2. Press SELECT while in the STOP JOB mode.
3. Press the right or left arrow key until SET JOB HOME appears
in the message box.
4. Press SELECT. The ARC station will beep twice to indicate

the position has been stored.
To change job home
Move the carriage to any position on the table and repeat the
steps above. The new position replaces the previously stored
position in the ARC station.
To display current job home
1. To avoid hitting clamps, slew the carriage near the home

position using the arrow keys.
in the message box.
4. Press SELECT to move the carriage to the precise Job Home

position.
5. Press the right or left arrow key until Absolute (X,Y): appears
in the message box.
6. Press SELECT to display the current position. This is the

current Job Home position.
Note: Make note of this position. If the carriage hits a clamp or

fixture and router position is lost, you can slew to this position or
set an absolute pre-position in ART Path and repeat the job, but
only if you reorient the system by turning the power off and then on
again.
58 Dimension 200
JOB HOME POSITION AND JOB BOUNDARIES
Job boundaries cannot exceed the active cutting area of the router
table. The Dimension 200 and ART Path interpret job boundaries
for certain job types in these ways:
Output repeats are considered to include all repeats within

the job boundary.
Paneled jobs are treated as separate jobs. The largest panel

must fit on the table.
Inplace repeats include the park position within the job

boundary.
PrePosition set in ART Path is included in the job boundary.
If the Job Home position will cause the job being processed to
exceed the table boundaries, the ARC station displays JOB WILL
EXCEED TABLE BOUNDARY in the message box.
To clear the boundary message
1. Press START/STOP to display the correction necessary to

permit the job to fit.
2. Press the arrow keys to move the carriage the distance in X

and Y indicated in the message. When the carriage is in an
acceptable position, the X and Y distances will be zero.
3. Press START/STOP again. If the job still exceeds boundaries,

the correction message is displayed again. If the job fits,
PRESS START TO SET HOME is displayed.
4. Press START/STOP again to set the current position as Job

Home and start the job.
RETURN HOME
The Return Home feature allows the operator to return the

carriage to the last Job Home position. The Job Home position is
stored when a job is started or when the Set Job Home function is
used.
To return home
1. To avoid hitting clamps or fixtures, move the carriage near the

home position using the arrow keys.
in the message box.
4. Press SELECT to move the carriage to the precise Job Home

position.
FEED RATE:
The Feed Rate is set in ART Path at the GRAPHIX ADVANTAGE.

It is the absolute speed in inches per minute or millimeters per
second at which the tool travels along the tool path. To override
this rate and reduce or increase the feed rate, change the
established Feed Rate by a percentage described below. The feed
rate will not exceed maximum velocity of the router.
The Feed Rate parameter is most frequently changed in the STOP

JOB mode when the Feed Rate has been set too high or too low for
the job in progress. The feed rate override is not cleared after the
job completes and will be applied to the next job.
The feed rate will not exceed maximum velocity of the router.
How-ever, if the Feed Rate set in ART Path is less than the
maximum, you may increase it using the Feed Rate parameter. A
Feed Rate of 200% would double the Feed Rate set in ART Path.
60 Dimension 200
To change feed rate
CAUTION: The feed rate override is not cleared after the job
completes and will be applied to the next job received.
2. Press the right or left arrow key until Feed Rate: appears in
the message box.
3. Press SELECT to obtain the Feed Rate percentage.
4. Press the right or left arrow keys to move the cursor to the
desired digit.
5. Press the up or down arrow keys to increase or decrease the

digit under the cursor. Acceptable values are 1% to 1000%.
6. Press SELECT to save the new value.
If the value is valid (1 - 1000%), the system beeps twice and

returns to the STOP READY or STOP JOB mode.
If the value is not valid, the display remains until a valid value
is entered or until RESET is pressed to exit the menu without
changing the Feed Rate.
MOTOR DELAY:
The Motor Delay parameter sets the time the tool will wait for the
router to reach full speed before it descends to the material. Valid
values are 0 to 99 seconds. Gerber recommends a setting of 05
(five seconds).
To change motor delay
2. Press the right or left arrow key until Motor Delay: appears in
the message box.
3. Press SELECT to obtain the Motor Delay time.
4. Press the right or left arrow keys to move the cursor to the
desired digit.
5. Press the up or down arrow keys to increase or decrease the

digit under the cursor. Acceptable values are 00 to 99.
6. Press SELECT to save the new value, or RESET to exit without

saving the value.
TEST:
This function allows testing both the router table and the ARC
station to ensure machine accuracy and integrity. The ARC station
does not accept data from the GRAPHIX ADVANTAGE during
testing.
A power-on test restarts the system, displays the revision level of

the system, and repeats orientation of the carriage at the lower left
corner of the table.
The remaining tests are not used by the operator unless instructed
to do so by Gerber technicians.
62 Dimension 200
DISPLAY:
This function allows you to set the language and units which
display in the ARC station message box.
It also allows you to turn Auto Scroll on or off. When on, Auto
Scroll automatically scrolls messages that are too long to fit in the
message box. When Auto Scroll is off, truncated messages are
displayed. Normally, Auto Scroll should be left on.
To change the language
2. Press the right or left arrow key until Display: appears.
3. Press SELECT.
4. Press the right or left arrow key until Language: and the
current language appear.
5. Press the right or left arrow key to scroll through the language
choices.
Language:
English
6. Press SELECT to save the selected choice.
The system beeps twice and returns to the STOP READY or

STOP JOB mode displayed in the entered language.
To change units
2. Press the right or left arrow key until Display: appears.
3. Press SELECT.
4. Press the right or left arrow key until Units: and the current
units appear.
5. Press the right or left arrow key to scroll through the units
choices (inches or millimeters).
Units:
Inches
6. Press SELECT to save the selected choice.
The system beeps twice and returns to the STOP READY or

STOP JOB mode displayed.
To turn Auto Scroll on or off
2. Press the right or left arrow key until Auto Scroll: appears.
3. Press SELECT.
4. Press the right or left arrow key to display On and Off.
5. Press SELECT to save the choice.
DEFAULT
This function allows you to reset all value parameters back to the
factory default settings.
To reset the defaults
1. Press SELECT while in the STOP READY mode.
2. Press the right or left arrow key until Default appears.
3. Press the SELECT key to reset all value parameters to the

factory default settings. The system beeps twice and returns
to the STOP READY mode.
65
System Preparation and Use
This section discusses the procedures to follow before and during

the operation of the Dimension 200:
Preliminary preparation
Router motor installation/removal
Tool selection, installation, removal, and replacement
Table mat milling and engraving
Material selection and preparation
Workpiece attachment to sacrificial material
Workpiece mounting to the router table
Chip removal system use
Mist coolant system use
Step height gage use

66 Dimension 200
Preliminary Preparation
Before preparing the Dimension 200 for operation, complete the
following steps:
1. Turn OFF the electrical box power switch.
2. Unplug the router motor power cable.
3. Raise the router motor by manually turning the Z axis

adjustment knob, located on top of the Z axis motor.
4. Adjust the feet of the Dimension 200 to a higher or lower

position to ensure that the router table is level.
System Preparation and Use 67
Router Motor Installation/Removal

For your convenience, the Dimension 200 is shipped with the
router motor already installed. However, should a problem occur
requiring the motor to be removed, please follow the instructions
below.
To remove the router motor
1. Turn off and unplug power at the router, electrical box, and
GRAPHIX ADVANTAGE.
2. Loosen the screws on the collar of the motor mount and

carefully slide the motor up the mount to remove it.
To install the router motor
Note: The photograph below is for illustration purposes only and may
vary somewhat from your router motor.
1. Locate the router motor and note the small pin or pins
(depending on the model) projecting from it.
2. Ease the router motor into the motor mount, matching the
pins to the grooves.
3. Slide the motor to the bottom of the mount.

68 Dimension 200
4. Tighten the screws on the collar of the motor mount and plug
in the router motor cord into the outlet on the router.
Note: The photograph below is for illustration purposes only and

may vary somewhat from your router motor.
The ARC station displays STOP READY after performing

diagnostics. The router system is now ready to operate.
5. Turn ON power at the router when ready to cut.

Tool Selection
PEN TOOLS
When first using the Dimension 200, be sure to learn as many

system functions as possible with the pen tool. Do not try to cut
material with the router until you have mastered the basic system
functions using the pen.
CUTTING TOOLS
The tool kit contains six spiral fluted solid carbide cutting tools.
Cutters used with the Dimension 200 must have a .499 - .500,
.249 - .250, or .124 - .125-inch shank for use with the .50 or .25-inch
collets, or the .125-inch collet adapter supplied in the tool kit. All
cutters must have plunge capabilities.
Note: Metric collets and tools are available from a Gerber distributor.
TOOL INFORMATION
The tools supplied in the tool kit are basic tools for average
cutting jobs. As you gain more experience, you may wish to
purchase additional cutters. The information below may be
helpful in your use and selection of tools.
The .25-inch cutter is the strongest cutter supplied and has a

longer cutting edge length than the .125-inch cutter.
The .25-inch cutter has a higher surface speed at the outside

edge, creating a higher chip removal rate and a smoother edge
finish.
The .25-inch cutter has a 0.75-inch cutting edge length. Any

material which is thicker than 0.75 inches requires a router bit
with a longer cutting edge length.
The .25-inch cutter creates a .125-inch radius on all inside

corners.
The .125-inch cutter creates a .0625-inch radius on all inside

corners.
70 Dimension 200
A .25-inch cutter may not fit through some openings. If this

occurs, use the .125-inch cutter if possible.
You may discover that characters can be cut smaller than the
recommended limits. If a .25-inch cutter is used, double the
size limit for the smallest characters in each style. If larger bits
are purchased, scale the limitations proportionally for larger
cutters.
Gerber sells a complete line of high quality cutting tools that

provide optimum cutting performance. Contact your
Distributor for details.
COLLETS
The tool kit contains two collets. One is a 1/2" collet intended for
use with the pen tool. The other is a 1/4" collet intended for use
with all 1/4" cutters.
A 1/4" cutter must have a diameter of .249-.250, and a 1/2"

cutter must have a diameter of .499-.500 inches.
If the cutter has a 1/8" shank, insert it into the 1/8" adapter
provided and use the 1/4" collet.
The cleanliness of the collet and the spindle is essential.

Damaged surfaces will affect the holding ability of the collet.
Be sure that the tapered inside diameter of the spindle, the
tapered outside diameter of the collet, and the inside diameter
of the collet are free of chips and debris.
The outside diameter of the cutting tool is an important factor

in the collet's ability to hold tools tightly in place. Use only
cutting tools that have a -0.001 inch (or less) tolerance on the
nominal outside diameter. Gerber authorized cutters comply
with these tolerances.
Insert the collet into the nut before you insert the tool. Insert
the tool bit, then install the nut on the bottom of the spindle.
This will make it easier to remove the adapter.
TOOL INSTALLATION
Solid carbide tools, such as those included in the tool kit, must be
handled very carefully.
caution: DO NOT STRIKE THE CUTTING EDGE WITH THE

COLLET OR ADAPTER DURING TOOL INSTALLATION.
To install the tool
1. Turn OFF the router motor.
2. Select the desired tool and the appropriate collet from the tool
kit.
3. Insert the tool into the collet and tighten with the wrenches
provided in the tool kit.
When installing the pen, position the bottom of the collet

about half-way up the shank of the tool.
When installing a cutter, position the bottom of the collet

approximately even with the top of the flutes. The collet
should not cover any portion of the flutes, and very little of
the straight portion of the shank should be exposed below the
collet.
4. Slew the carriage to near the front edge of the router table.
5. Remove the retaining nut from the base of the router motor
using the wrenches supplied in the tool kit.
72 Dimension 200
6. Be sure that the collet and spindle are clean and undamaged.
7. Insert both the tool and collet into the opening at the base of the
router motor, as shown below.
8. Hold the collet to prevent the tool from falling out and hand
tighten the retaining nut.
9. Hold a wrench in one hand and place it on the flats of the

router motor chuck.
10. Hold the other wrench in the opposite hand and place it on
the flats of the retaining nut.
11. Tighten the retaining nut by pushing the wrenches with a firm
even force.
TOOL REMOVAL
CAUTION: When removing a tool, do not attempt to gain leverage

by jamming one wrench against the carriage while pushing on the
other.
DO NOT position the router motor over the router table without
any material underneath, such as foam board or a soft cloth. The
tool might fall out when the retaining nut is loosened and break or
damage the cutting edge.
74 Dimension 200
To remove a tool
1. Use the slew keys to position the carriage near the front of the
router table.
2. Turn OFF the router motor.
3. Loosen the retaining nut using one wrench while holding the
router motor chuck firmly with the other wrench.
4. Remove the tool from the collet.
PEN TOOL REPLACEMENT
To replace a pen
1. Unscrew the top of the pen assembly.
2. Remove the spring.
3. Remove the pen.
4. Insert the replacement pen into the pen barrel.
5. Replace the spring, and replace the cover on top of the barrel.
REPLACEMENT CUTTERS
Replacement cutters are available from Gerber. Different cutters

purchased from other dealers may or may not provide satisfactory
results with the Dimension 200.
Gerber is not responsible for results obtained with cutters not

recommended in this manual or purchased from other dealers. Be
sure to get only the highest quality cutters for use with the
Dimension 200.
Table Mats
The Dimension 200 table mats provide accurate depth control and
minimize the need for sacrificial material. They are installed at
the factory but are milled on-site after installation to provide a
perfectly flat surface.
A grid that aids alignment can also be engraved into the mats.
Files containing data for both operations are supplied with ART
Path, and bits for both operations are supplied in the tool kit.
Note: Gerber recommends using the Chip Removal System and pressure
foot for this procedure.
MAT MILLING
The mat milling data is supplied with ART Path in the file
D200MILL.RTP.
1. In ART Path, choose Open from the File menu.
2. Highlight Router Files under List Files of Type to open

D200MILL.RTP. Click on OK.
3. In the Setup menu, select Start/End position.
4. Set the Start/End position to start and end the machine at the
lower left.
5. Click on OK.
6. Install the table surfacing bit supplied in the tool kit.
7. On the ARC station, press Z INIT once to unlock the Z axis.
8. Place the tool height gage on the surface of the mats under the
bit. Use the Z axis knob to lower the tool until it just touches
the gage.
9. Press Z INIT once. This lifts the Z axis once and locks it. The
tool is now initialized to the table surface.
76 Dimension 200
10. Using the arrow keys, move the carriage to the extreme lower
left corner (absolute 0,0 or the orientation point) of the table.
11. In ART Path, click on Output. The Job Output dialog box
appears. (Make sure that no pre-position moves have been
entered.)
12. Click on Rout.
13. Press START/STOP three times to begin table milling. This

displays the header and tool messages and begins routing.
Grid Engraving
The grid consists of a numbered grid that assists in precise
alignment of material on the table. It should be engraved on the
mats after the mats have been milled.
After milling the table mats, choose the appropriate grid

engraving procedure described to engrave the grid:
normal grid engraving

grid engraving with the T-Vac System option installed
NORMAL GRID ENGRAVING
The grid engraving data needed is supplied with ART Path in the
file ENGRGRID.RTP.
ENGRGRID.RTP
The number data is supplied in the file GRIDNUMB.RTP.
GRIDNUMB.RTP
To engrave the grid

ENGRGRID.RTP. Click on OK.
lower left.
5. Click on OK.
6. Install the .020 engraving bit supplied in the tool kit.
the gage.
78 Dimension 200
entered.)
12. Click on Rout.
13. Press START/STOP three times to begin grid milling. This

To engrave the grid numbers
Note: Use the same .020 engraving bit as above.
2. To engrave the numbers, highlight Router Files under List

Files of Type to open GRIDNUMB.RTP. Click on OK.
lower left.
5. Click on OK.
the tool height gage.
entered.)
11. Click on Rout.

12. Press START/STOP three times to begin table milling. This

GRID ENGRAVING WITH T-VAC OPTION
The grid engraving program is supplied with ART Path in the

VACGRID.RTP file. The VACGRIDM.RTP file contains a similar grid
for use with a metric system.
VACGRID.RTP3
To engrave the grid

VACGRID.RTP (or VACGRIDM.RTP). Click on OK.
lower left.
5. Click on OK.
6. Install the .020 engraving bit supplied in the tool kit.

80 Dimension 200
the gage.
left corner (absolute 0,0 or the orientation point) of the table
and set Job Home Position.
entered.)
12. Click on Rout.
13. Press START/STOP three times to begin the grid. This

Material Selection and Preparation

The Dimension 200 can draw on any kind of material suitable for a
ballpoint pen, and cut virtually any routable material including
those listed below.
ROUTABLE MATERIALS
Plastics Woods Metals*

Acrylic Hard Aluminum
Polycarbonate Soft Brass
Phenolic Masonite Copper
Styrene Plywood Bronze
Foam Board Particle Board
* All metals require use of the Mist Coolant system.
CAUTION: Steel or stainless steel is not recommended for use

with the Dimension 200.
Because different routable materials have different densities,

varying cutting speeds are required. A table of recommended
cutting speeds for various materials is included at the back of this
manual.
CHOOSING SACRIFICIAL MATERIAL
You may place a piece of sacrificial material under the workpiece

when cutting. The best sacrificial materials are foam or acrylic.
Pressed boards such as chip board and masonite can be used;
however, pressed boards contain glue, which is abrasive to
cutters. Abrasive materials can wear out the tips of cutters and
degrade their plunge capabilities.
Acrylic is recommended over pressed board.
When using acrylic as a sacrificial material, remove the

protective paper coating from the sacrificial acrylic surface.
Select sacrificial material of similar density to the material

being cut.
Attaching the Workpiece to Sacrificial Material

When not cutting to the mask, attach the workpiece to the
sacrificial material using one of the following methods:
Double-Sided High Tack Tape

Double-Sided Tape
Spray Adhesive
Follow the guidelines below when attaching the workpiece to the
sacrificial material before mounting the workpiece on the router
table.
Hard Metals
For brass, other metals, or hard wood:
Use Double-Sided High Tack Tape. Specially formulated Double-

Sided High Tack Tape is unaffected by mist coolant spray and is
82 Dimension 200
especially suitable for securing metals which produce high cutting

forces.
High Tack Tape is available through Gerber or most industrial and office
supply distributors.
Note: Using both tape and spray adhesive is a good alternative on

rough-textured wood.
Thin Metals
For thin aluminum or other thin metals:
Use less aggressive Double-Sided Tape. The 3M #410 Double-

Sided Tape is especially suitable for securing thin aluminum or
other light materials to avoid bending the metal when lifting them
after cutting. This tape is available from most industrial and office
supply distributors.
Note: Do not use foam-filled Double-Sided mounting tape. Spray

adhesive works well on thin aluminum.
Non-Metals
For plastic, Styrofoam, thin wood, or other non-metallic

materials:
Use Spray Adhesive. Spray Adhesive is especially suitable for

securing plastic, Styrofoam, wood or other non-metallic materials.
Spray Adhesive is available from Gerber or most industrial and

office supply distributors. Low-tack tape may also be appropriate
for certain types of wood, which tend to splinter when high-tack
tape is removed.
Note: When using acrylic materials as a workpiece, do not remove the

protective paper sheets which preserve the acrylic surface from scratches
during cutting. If the acrylic materials are supplied unmasked, you may
wish to apply the transfer tape before spraying on the adhesive.
USING TAPE
Follow these guidelines when using tape to attach the workpiece

to the table mats:
Place the tape in closely spaced strips.

Do not overlap the strips.
Make sure the centers of letters like O, B, and P are held
securely by the tape.
To use double-sided tape
Follow these steps when using double-sided tape to secure the

workpiece to the sacrificial material:
1. Lay the tape across the underlying material.
2. Place the workpiece on top of the tape.
3. Press firmly to bond securely.
USING SPRAY ADHESIVE
When using spray adhesive, refer to the manufacturer's

suggestions on the can.
WARNING: Apply spray adhesive only in a well-ventilated

area.
84 Dimension 200
CAUTION: Spray adhesive is sticky. Do not spray near the

router table.
To attach the workpiece to the sacrificial material
1. Spray the adhesive in smooth, even strokes across the back of

the workpiece.
2. Coat the entire surface uniformly, including edges and corners, until
tacky, but not wet.
3. Press the workpiece firmly onto the sacrificial material.
Mounting the Workpiece

After adhering the material to sacrificial material, or if you are not
using sacrificial material, you may mount the workpiece on the
table using clamps, the T-Vac, or a combination of both.
USING CLAMPS
After the workpiece is adhered to the sacrificial material (if used),

attach the entire workpiece to the router table with work clamps.
Use all four work clamps to ensure that the workpiece is held
down securely. The clamps can be reversed so that they may be
used with either thick or thin material, as shown below.
Note: Your router may vary from the photographs.

If the workpiece is thick, use a clamp block (shim) of equal

thickness under the free end of the work clamp to keep the clamp
level and maximize its holding ability.
CAUTION: When moving the router motor with the slew keys,
or during router operation, take care not to run the vacuum
shroud into the work clamps. Make sure the work clamps are
not in the tool path.
To use the clamps
1. Press the slew key to move the router carriage to the back of
the router table.
2. Place the workpiece in the center of the router table.
3. Locate the work clamps in the tool kit. Each work clamp
consists of a strap, clamping nut, and nut/stud assembly.
4. Insert the strap over the stud and thread on the clamping nut
before clamping the material.
5. Position the work clamp on the edge of the workpiece.
6. Hand-tighten the work clamp by hand.
Note: Over tightening the clamps can bend them, making them less
effective.
7. Slew the router motor and tool over the workpiece.
Note: The descriptions of drawing and cutting that follow assume no (or
minimal) vacuum hold-down. Less clamping is needed with T-Vac.
Drawing
If the workpiece is thin, use the thinner side of the clamp, as

shown on the previous page. When drawing, two work clamps
are normally sufficient to hold the paper and sacrificial material
securely in place.
Cutting
When cutting, use all four work clamps to hold the workpiece and
sacrificial material securely in place.
86 Dimension 200
USING T-VAC VACUUM HOLD-DOWN
The T-Vac Vacuum System reduces the need for adhesives and
sacrificial materials because it holds the workpiece securely on the
table without adhesives. With certain materials, you may wish to
use sacrificial material. T-Vac is not recommended for use with
very small workpieces, very thick or porous materials, or
materials with irregular surfaces.
CAUTION: IT IS ADVISABLE TO USE CLAMPS IN

ADDITION TO T-VAC VACUUM HOLD-DOWN IF THE
WORKPIECE IS THICK OR THE JOB IS LARGE TO PREVENT
ACCIDENTAL WORKPIECE MOVEMENT IF THE VACUUM
IS INTERRUPTED.
When using T-Vac vacuum hold-down, follow these guidelines:
The workpiece must be flat.

Do not use T-Vac with porous materials, very thick materials,
or materials with irregular surfaces.
The workpiece must cover most of the vacuum holes. Up to 30
holes may be uncovered at the start of the job. Additional
holes may be uncovered as the job progresses. Use scrap
material to cover the holes that are not covered by the
workpiece.
Use the Chip Removal System and keep the table surface
clean.
USING BOTH CLAMPS AND T-VAC
For large jobs, it is advisable to also clamp the workpiece to

prevent movement if a power outage or other condition interrupts
the vacuum.
Using the Chip Removal System

Use the Chip Removal System when cutting plastic, Styrofoam,
and wood. Disconnect the removal system when pen plotting or
cutting metals such as aluminum or brass.
CAUTION: The Chip Removal System cannot be used with the

Mist Coolant System.
To use the Chip Removal System
1. Make sure that the Chip Removal System has been properly
installed. (See the section on installation, if necessary.)
2. Press the START key on the ARC station to start the job. The
vacuum is switched on by the electrical box when the job
starts.
88 Dimension 200
PRESSURE FOOT AND PRESSURE FOOT PAD
The Chip Removal System includes a pressure foot to hold

material flat against the router table to prevent it from lifting
while routing.
The pressure foot also makes the router safer by preventing chips
and small pieces of material from being thrown out of the
machine while routing.
Using the pressure foot saves time and money by reducing the
need for bonding and sacrificial material.
The pressure foot has a removable pad that rests on the workpiece
and slides smoothly over it during cutting operations. The tool
extends through an opening in the pressure foot pad. Two pads
are supplied, one with a 1.5" (38 mm) diameter opening for
normal use, and one with a 0.4" (10 mm) diameter opening for
cutting very small pieces without risk of pulling the piece off the
table and into the vacuum.
To install the pressure foot
1. Align the pressure foot to the four pins attached to the shroud.
2. Turn counterclockwise to install.
To remove the pressure foot
1. Grasp the pressure foot with your hand (or insert a screw
driver into a vent hole).
2. Turn clockwise to remove.

To replace the pressure foot pad
1. Align the pad screw holes with the holes on the pressure foot.
2. Replace the screws and tighten just enough to compress the

cushion slightly. A thread locking compound should be used.
Loctite Thread Locker is recommended.
3. Replace the pressure foot window.
4. Replace the screws and tighten.

90 Dimension 200
Using the Mist Coolant System

CAUTION: The Mist Coolant System has been designed to be
used with Gerber Cool coolant. DO NOT dilute Gerber Cool
prior to use.
CAUTION: Use of other types of fluids may damage the system.

DO NOT use toxic or volatile liquids.
The adjustable drip rate allows for a wide range of mist "wetness"
and cooling capability. The evaporation of the mist provides the
desired cooling effect and minimizes heat build-up of the
remaining lubricant as well.
To use the Mist Coolant System
1. Turn on the compressor and set the air pressure at 20-40 psi as
indicated on the mist coolant air pressure gage.
To increase air pressure, turn the air pressure regulator

clockwise.
To decrease air pressure, turn the air pressure regulator
counterclockwise.
2. Remove the brass filler plug using a flat head screwdriver and
fill the reservoir with Gerber Cool coolant. The reservoir
should remain full to assure proper lubrication. Add coolant
periodically to maintain the level.
3. Adjust the coolant nozzle so that it is directed at the point of

cutting.
CAUTION: Keep the nozzle at a safe distance to avoid

damaging it with the cutter.
4. Open the shut off valve near the nozzle coupling mounting
block. When open, the handle is aligned vertically with the
coolant tubing.
5. Starting with a drip rate of six drops per minute, adjust the
drip rate and air pressure to provide a mist wet enough to
create a slight beading of moisture on the workpiece. Avoid
an excessively "dry" mist. Better cooling and mist placement
are achieved when larger mist droplets are used. Ideally the
coolant should evaporate during cutting.
6. Adjust the drip rate and lubricant flow by turning the drip
regulator on the top of the coolant reservoir.
To increase the drip rate, turn the regulator

counterclockwise.
To decrease the drip rate, turn the regulator clockwise.
Using the Step Height Gage

The step height gage enhances the depth accuracy of the
Dimension 200. When working with a milled table surface, you
can set the depth of cut so precisely that masked materials, such
as acrylic sheet, can be cut while leaving the bottom layer of
masking paper intact. This eliminates the need for separate
adhesives to hold the cut shape in the workpiece and can do away
with the need for sacrificial material.
92 Dimension 200
UNLOCK AND INITIALIZE THE Z AXIS
1. Place the step height gage on the milled table surface next to
the workpiece to be cut. Ensure that the table surface is clean.
Note: Debris under the gage will cause inaccurate measurement

and poor results.
2. Using the arrow keys, position the tool over the step on the
gage marked with the thickness of the material to be cut.
Note: The actual step height is larger than the thickness marked. Do
not use the step height gage as a measuring device.
3. Press Z INIT on the ARC station. Turn the Z axis ways knob
until the tool just touches the appropriate gage step.
CAUTION: Excessive pressure will cause tool damage.
4. Press Z INIT once.

DEPTH OF CUT
Set the depth of cut in ART Path to the decimal equivalent of the
step height selected on the step height gage. This will leave the
bottom mask layer intact. Decimal equivalents of step heights are
shown below.
Step Decimal
Equivalent
1/16 .063
1/8 .125
3/16 .188
1/4 .250
5/16 .313
3/8 .375
7/16 .438
1/2 .500
9/16 .563
5/8 .625
11/16 .688
3/4 .750
13/16 .813
7/8 .875
15/16 .938
1 1.000
95
Cleaning and Maintenance
The Dimension 200 is relatively simple to operate and easily

maintained. However, routine checking and cleaning of the
equipment can significantly reduce the likelihood of major
problems.
Router maintenance is based on daily inspection of the

equipment and daily and weekly cleaning procedures.
Daily and weekly inspections of the router are recommended to

help establish a cleaning schedule appropriate to the
environment. Use the charts provided as inspection guidelines.
96 Dimension 200
Daily Inspection
Component What To Check For
Entire machine surface Chip buildup, mist coolant

buildup, table slot debris
X and Y ways Debris buildup
Lead screws Debris buildup
Router carriage, linear Debris buildup

bearing seals
Mist coolant nozzle Coolant buildup
Mist coolant tank Coolant level
T-Vac filter Debris buildup
Electrical box air filter Debris buildup
Cleaning Recommendations
WARNING: BEFORE PERFORMING ANY CLEANING
PROCEDURE, TURN OFF THE ROUTER MOTOR AND
UNPLUG THE ELECTRICAL BOX FROM ITS POWER
SOURCE.
DAILY CLEANING
Use the daily inspection to help establish a cleaning schedule that

is appropriate for the router environment. The daily cleaning
procedures recommended are based on average use of the
Dimension 200.
Cleaning and Maintenance 97
TWICE WEEKLY CLEANING
Clean the T-Vac air filter twice a week or even more frequently if
there is heavy use. Debris buildup in the filter will reduce vacuum
hold-down and may cause the vacuum to overheat and fail.
SUPPLIES
The following tools and supplies are recommended for the

cleaning procedures:
Shop vacuum
Lint-free cloth
Hand broom
1" (25 mm) nylon or natural bristle brush
2.5 mm and 4 mm hex head wrenches
Light machine oil
Daily Cleaning
Y AXIS WAYS
The Y axis ways are the shafts on which the beam moves. There is
one Y axis way on each side of the work table, running the length
of work table.
1. Locate the Y axis ways.

2. Clean the Y axis ways by wiping them with a lint-free cloth.
98 Dimension 200
X AXIS WAYS
The X axis ways are the shafts located on the beam on which the
router motor carriage moves.
To clean the X axis ways
1. Locate the two X axis ways.
2. Clean the X axis ways by wiping them with a lint-free cloth.

LEAD SCREWS
The lead screws are located along the width of the router motor
carriage below the ways, on the Z axis, and beneath the center
front of the router. (See the previous photograph and illustration.)
CAUTION: DO NOT OIL THE LEAD SCREWS.
1. Use a brush to remove debris from the lead screws.
Note: The “teflon” coating on the lead screws will gradually wear
away. This is normal and will not affect performance.
ROUTER TABLE SURFACE
To clean the router table surface
1. Use a hand broom to clean the router table surface after each
operation, brushing away the chips from around the router
motor and the work table.
2. Use the lint-free cloth to wipe the table clean.
MIST COOLANT
The Mist Coolant System requires two maintenance procedures:

checking the mist coolant fluid level and cleaning the mist coolant
nozzle.
To check the mist coolant
1. Regularly check the mist coolant tank to ensure that it

contains enough coolant to avoid running out during a job.
2. If the coolant level is low, fill the tank to within one inch (25
mm) of the top of the level indicator. Overfilling may result in
the tank leaking.
To clean the mist coolant nozzle
1. Use a lint-free cloth to wipe off any coolant build-up.

100 Dimension 200
Weekly Inspection
Component What To Check For
Z axis ways Debris buildup
X and Y axis ways Debris buildup
Electrical box air filter Debris buildup on filter

element
Weekly Cleaning
The weekly cleaning and maintenance procedures include the
following:
cleaning and oiling the ways

cleaning the electrical box air filter
Z AXIS WAYS
1. Locate the Z axis ways on either side of the router motor.
2. Lower the router motor to its lowest position by turning the Z

axis adjustment knob.
3. Clean and oil the upper part of the Z axis ways.
4. Use a lint-free cloth to clean the way.
5. Lightly oil the Z axis way with light machine oil.
6. After cleaning the upper part of the Z ways, raise the router
motor to its highest position by turning the Z axis adjustment
knob.
7. Clean and oil the lower part of the Z axis ways.
8. Use a lint-free cloth to clean the way. Lightly oil the way.
X AND Y AXIS WAYS
See the photograph under the “Daily Cleaning” section for parts
identification.
1. Use a lint-free cloth to clean the X and Y axis ways.
2. Lightly oil the X and Y axis ways with a light machine oil.
ELECTRICAL BOX AIR FILTER
The air filter is located on the electrical box. In harsh

environments, the air filter may need more frequent cleaning than
recommended.
1. Turn OFF the main power switch and unplug the electrical
box from its power source.
2. Snap off the air filter cover from the front of the electrical box.
3. Remove the air filter from the cover.
4. Vacuum thoroughly to remove any dust or debris.
5. Return the air filter to the cover.
6. Return the cover to its former position and snap into place.
102 Dimension 200
ROUTER MOTOR LUBRICATION
The router motor bearings are lubricated during assembly but

must be lubricated after every 1000 hours of operation. This
procedure refers to the High Frequency Spindle Motor Option
only.
1. Use a lithium-based, NLGI grade 2 grease, such as Optimal

Longtime PD2 or Leuber Isoflex LDS 18 Special A.
CAUTION: Before lubricating the bearings, clean the grease

nipples carefully to prevent dust or dirt from entering the
motor.
2. Lubricate each bearing with 2 grams of grease.
CAUTION: Do not over-lubricate. Over-lubrication will

cause excessive heat build-up.
3. Weekly, clean and grease the cams with lithium-based or

white grease.
103
Index air filter ..........................................97

daily................................................92
lead screws ....................................94
A mist coolant tank and nozzle......95
supplies..........................................93
Absolute X,Y .....................................52
weekly............................................96
Acrylic....................................77, 78, 79
work table......................................93
Aluminum .........................................33
X and Y axis ways ........................97
ARC Station.......................................16
Z axis ways....................................96
connect to GA................................22
Collets ................................................68
display panel .................................40
Coolant ..............................................86
front panel .....................................40
Customer Support..............................2
function keys.................................42
Cutting...............................................82
functions ........................................39
Cutting tools .....................................67
power supply ................................16
power-up tests ..............................41 D
setting up .......................................23
testing.............................................59 Daily cleaning...................................92
to electrical box .............................16 Daily inspection................................92
to router table................................16 Default settings.................................61
ART Path Depth of cut ................................87, 89
job home position .........................37 Diagnostics........................................66
mat milling data ...............72, 73, 76 power-up .......................................23
Auto Scroll...................................60, 61 DISPLAY ...........................................60
Axes Display panel ....................................40
of movement .................................35 Double-sided high tack tape...........78
X, Y, Z.............................................35 Double-sided tape......................79, 80
Drawing.............................................82
B
E
Boundary message ...........................56
Electrical box.............................3, 5, 16
C air filter cleaning ..........................97
to router table................................17
Changing tools..................................46
Electrical requirements......................4
Chip Removal System............4, 18, 83
Engraver vacuum system ...............32
installation .....................................18
Engraving
pressure foot..................................83
grid numbers.................................75
using ...............................................83
vacuum shroud.............................19 F
with mat milling ...........................72
Clamps .........................................81, 82 Feed Rate ...........................................57
Cleaning Function keys
104 Dimension 200
arrows ............................................42 Job Home Position ...............37, 53, 56

Reset ...............................................48
Select...............................................50 L
Start.................................................45 Language ...........................................60
Start/Stop ......................................43 Lead screws.................................92, 94
Stop.................................................45 Low-tack tape ...................................79
Z Init .........................................36, 49
M
G
Main power switch ..........................38
Gerber Cool coolant ...................25, 86 Mat milling data...............................72
Grid engraving .................................73 Material selection .............................77
grid numbers.................................75 Menu Select mode............................48
normal ............................................73 Menu selection
with T-Vac .....................................76 Absolute X,Y .................................52
Grid engraving data.........................73 Default ...........................................61
Grid numbers....................................75 Display...........................................60
Ground strap cables .........................20 Feed Rate .......................................57
Motor Delay ..................................59
H Return Home ................................57
Hard metals.......................................78 Set Job Home.................................53
High Frequency Spindle Option .4, 6, Test .................................................59
25, 27, 31, 98 Metals...........................................77, 78
Home Position ..................................37 Mist coolant
current ............................................55 fluid level.......................................95
nozzle .............................................95
I Mist Coolant System........................25
Initializing air pressure....................................86
Z Axis .............................................36 compressed air................................4
Inplace repeats ..................................56 drip rate adjustment ....................87
Installation installation.....................................26
Chip Removal System..................18 using...............................................86
Mist Coolant System ....................25 Motor Delay ......................................59
pressure foot..................................84
router..............................................15
N
router motor ..................................65 Non-metals........................................79
Speed Controller...........................30
T-Vac Vacuum System.................28 O
Operating principles........................35
J Orientation ..................................52, 59
Job boundaries ..................................56 Orientation point......41, 72, 74, 75, 77
Index 105
Output repeats ..................................56 Slew ..............................................42, 81

Speed controller..............................4, 6
P installation.....................................30
Paneled jobs ......................................56 Speed Controller System.................31
Pause mode .......................................45 Spindle speed....................................31
Plastics .........................................77, 79 Spray adhesive .................................79
Point of orientation ..........................41 Start Job .............................................44
Power connections ...........................22 Start Mode...................................43, 48
Power switch Start position.....................................37
emergency .....................................38 Start Ready ........................................43
main................................................38 step height gage................... 49, 87- 89
rotor motor ....................................38 step heights
Power-up diagnostics ......................23 decimal equivalents .....................89
Preposition ..........37, 53, 55, 73, 75, 77 Stop Job..............................................45
PrePosition ........................................56 Stop Mode .........................................44
Pressure foot......................................83 Stop Ready ........................................45
installation .....................................84 Styrofoam ..........................................79
removal ..........................................84
replacement ...................................85
T
Table Mats .........................................72
R Thin metals........................................79
Repeat job ..........................................47 Tool change.......................................46
Replacement cutters.........................71 Tool height gage.............49, 72, 75, 77
Resume processing...........................46 Tools
Return Home.....................................57 bits ..................................................67
Rotor motor cutting ............................................67
bearings..........................................98 information ...................................67
Routable materials............................78 installation.....................................69
Router maintenance .........................91 pen ..................................................71
Router motor removal ..........................................70
installation .....................................65 replacement...................................71
lubrication......................................98 T-Vac vacuum
removal ..........................................65 and clamps ....................................83
Router motor power switch ............38 guidelines ......................................83
Router stand ........................................3 T-Vac Vacuum System ......4, 5, 28, 82
air filter cleaning ..........................92
S and grid engraving ......................76
installation.....................................28
Sacrificial material......................78, 81
Safety guidelines ..............................33
Select key ...........................................51
106 Dimension 200
U
Units ...................................................60
V
Vacuum hose.....................................19
W
Weekly Cleaning ..............................96
Weekly Inspection............................96
Wood ......................................77, 78, 79
Work clamps .....................................81
Work Space..........................................3
Workpiece
attachment .....................................78
mounting .......................................81
using double-sided tape ..............80
using spray adhesive ...................80
using tape ......................................79
X
X axis ..................................................35
X axis ways........................................97
cleaning..........................................94
X, Y, Z Axes .......................................35
Y
Y axis ..................................................35
Y axis ways........................................97
cleaning..........................................93
Z
Z axis ................................35, 36, 49, 64
Initializing .............36, 38, 46, 49, 88
Z axis ways
cleaning..........................................96
Z INIT...........................................36, 49
Table of Contents
INTRODUCTION...............................................................................................................1
Manual Contents...........................................................................................................1
Conventions ..................................................................................................................2
Customer Support .........................................................................................................2
ROUTER REQUIREMENTS .............................................................................................3
Work Space Requirements ...........................................................................................3
Equipment Requirements .............................................................................................3
Router Stand...........................................................................................................3
Electrical Box.........................................................................................................3
High Frequency Spindle Option and Speed Controller .........................................4
Mist Coolant Compressed Air................................................................................4
Chip Removal System............................................................................................4
T-Vac Vacuum System ..........................................................................................4
Electrical Requirements................................................................................................4
Router Package Contents..............................................................................................7
Tool Kit Contents .........................................................................................................9
ROUTER STAND ASSEMBLY ......................................................................................11
Assemble the Leg Assembly ......................................................................................11
Assemble the Stand ....................................................................................................13
Mount the Router Table on the Stand ........................................................................13
Level the Stand and Router Table ..............................................................................13
ROUTER INSTALLATION PROCEDURE ....................................................................15
Before You Begin.......................................................................................................15
Connect Power Supply to ARC Station......................................................................16
Connect Router Table to ARC Station .......................................................................16
Connect Electrical Box to ARC Station .....................................................................16
Connect Electrical Box to Router Table.....................................................................17
Connect Chip Removal System ..................................................................................18
Installing the Chip Removal System....................................................................18
Connect the Ground Strap Cables ..............................................................................20
Connect GRAPHIX ADVANTAGE to ARC Station ................................................22
Power Connections .....................................................................................................22
Set Up the ARC Station..............................................................................................23
OPTIONAL EQUIPMENT INSTALLATION .................................................................25
Mist Coolant System ..................................................................................................25
Installing the Mist Coolant System......................................................................26
T-Vac Vacuum System...............................................................................................29
Speed Controller System ............................................................................................31
Using the Speed Controller System .....................................................................32
Engraver Vacuum System Option ..............................................................................33
SAFETY GUIDELINES ...................................................................................................35
OPERATING PRINCIPLES .............................................................................................37

Overview.....................................................................................................................37
X, Y, Z Axes...............................................................................................................37
Z Axis .........................................................................................................................38
Job Home Position......................................................................................................39
Power Switch..............................................................................................................40
ARC Station................................................................................................................41
Front Panel ...........................................................................................................42
Power-Up Tests ..........................................................................................................43
Function Keys.............................................................................................................44
START/STOP ......................................................................................................45
RESET .................................................................................................................50
Z INIT ..................................................................................................................51
ENTER.................................................................................................................52
SELECT ...............................................................................................................52
Using Select................................................................................................................53
Absolute X,Y .......................................................................................................54
Set Job Home .......................................................................................................55
Job Home Position and Job Boundaries...............................................................58
Return Home ........................................................................................................59
Feed Rate..............................................................................................................59
Motor Delay .........................................................................................................61
Test.......................................................................................................................61
Display .................................................................................................................62
Default..................................................................................................................63
SYSTEM PREPARATION AND USE ............................................................................65
Preliminary Preparation..............................................................................................66
Router Motor Installation/Removal............................................................................67
Tool Selection.............................................................................................................69
Pen Tools..............................................................................................................69
Cutting Tools........................................................................................................69
Tool Information ..................................................................................................69
Collets ..................................................................................................................70
Tool Installation ...................................................................................................71
Tool Removal.......................................................................................................73
Pen Tool Replacement .........................................................................................74
Replacement Cutters ............................................................................................74
Table Mats ..................................................................................................................75
Mat Milling ..........................................................................................................75
Grid Engraving ...........................................................................................................76
Normal Grid Engraving........................................................................................76
Grid Engraving with T-Vac Option .....................................................................79
Material Selection and Preparation ............................................................................80
Routable Materials ...............................................................................................80
Choosing Sacrificial Material ..............................................................................81
Attaching the Workpiece to Sacrificial Material........................................................81
Using Tape ...........................................................................................................83
Using Spray Adhesive..........................................................................................83
Mounting the Workpiece ............................................................................................84
Using Clamps .......................................................................................................84
Using T-Vac Vacuum Hold-Down ......................................................................86
Using Both Clamps And T-Vac ...........................................................................87
Using the Chip Removal System................................................................................87
Pressure Foot and Pressure Foot Pad ...................................................................88
Using the Mist Coolant System ..................................................................................90
Using the Step Height Gage .......................................................................................91
Unlock and Initialize the Z Axis ..........................................................................92
Depth of Cut.........................................................................................................93
CLEANING AND MAINTENANCE...............................................................................95
Daily Inspection..........................................................................................................96
Cleaning Recommendations .......................................................................................96
Daily Cleaning .....................................................................................................96
Twice Weekly Cleaning.......................................................................................97
Supplies................................................................................................................97
Daily Cleaning............................................................................................................97
Y Axis Ways ........................................................................................................98
X Axis Ways ........................................................................................................98
Lead Screws .........................................................................................................99
Router Table Surface ...........................................................................................99
Mist Coolant.........................................................................................................99
Weekly Inspection ....................................................................................................100
Weekly Cleaning ......................................................................................................100
Z Axis Ways.......................................................................................................100
X and Y Axis Ways ...........................................................................................101
Electrical Box Air Filter.....................................................................................101
Router Motor Lubrication ..................................................................................102

Gerber D200 - Users - Manual

Uploaded by

Copyright:

Available Formats

Gerber D200 - Users - Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Gerber D200 - Users - Manual

Uploaded by

Copyright:

Available Formats

1

The Dimension 200 is a router/engraver for three-dimensional

The ART Path Software Option allows the GRAPHIX

The Dimension 200 can cut designs from a variety of materials, as

Warning: THE DIMENSION 200 IS A COMPUTER-

 Router requirements and package contents

 Cleaning and maintenance procedures

Note: A note contains important information which could affect

CAUTION: A caution statement contains information which, if not

WARNING: A warning statement contains information which, if

If possible, please use a phone that is close to your GRAPHIX

 MS-DOSand Microsoft Windows version numbers

This section discusses the work space, equipment, and electrical

Work Space Requirements

A 3-ft. clearance on all sides of the router stand is the

CAUTION: Do not place a router in a damp work area. The

range between 0 and 70%.

A 48 in. square table or stand (with 3-ft. clearance on all sides, or

Gerber recommends placing the electrical box on the table beside

HIGH FREQUENCY SPINDLE OPTION AND SPEED CONTROLLER

The Speed Controller is used only with the High Frequency

MIST COOLANT COMPRESSED AIR

The optional Mist Coolant System requires 30-100 psi of

CHIP REMOVAL SYSTEM

The Chip Removal System requires a wet/dry shop vacuum with

T-VAC VACUUM SYSTEM (FACTORY-INSTALLED)

The optional T-Vac Vacuum System requires a vacuum blower

Note: The High Frequency Spindle Speed Controller and T-Vac

Requirements are as follows:

 Export systems: 200, 208, 220, 230, or 250V AC, 20 amp, 50

T-Vac Vacuum System:

Note: If the High Frequency Spindle Option is purchased, a licensed

Router Package Contents

WARNING: Do not attempt to assemble and install the

caution: BE EXTREMELY CAREFUL WHEN UNPACKING

1 ADVANTAGE Router Control (ARC) Station

Small Components Box:

Chip Removal System:

Mist Coolant System (Option):

Tool Kit Contents

1 Collet wrench set

Router Stand Assembly

Warning: THIS PROCEDURE REQUIRES AT LEAST FOUR

CAUTION: When removing the four foot subassemblies from

Assemble the Leg Assembly

2. Unscrew and remove the four foot subassemblies from the

3. Attach one foot subassembly to the bottom of each leg of the

Assemble the Stand

3. Use a carpenter's square to align all parts of the stand. Hand

Mount the Router Table on the Stand

Level the Stand and Router Table

Note: It may be easier to screw the nuts up or down on the foot

3. To raise a foot subassembly, use a 13 mm wrench to loosen the

Router Installation Procedure

Before You Begin

WARNING: Turn OFF and unplug any lettering systems or

WARNING: THE MAIN POWER BREAKER SWITCH ON

Power Off Check

 The main power breaker switch on the front panel of the

Router requirements and package contents

Cleaning and maintenance procedures

MS-DOSand Microsoft Windows version numbers

Export systems: 200, 208, 220, 230, or 250V AC, 20 amp, 50

The main power breaker switch on the front panel of the

ARC station to the electrical box

foot mount block on the Dimension 200 router table to the

vacuum hose pressure foot to the electrical box.