User's Manual: Satellite C650/C650D Satellite Pro C650/C650D Series
User's Manual: Satellite C650/C650D Satellite Pro C650/C650D Series
Satellite C650/C650D
Satellite Pro C650/C650D Series
Copyright
© 2010 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior writ-
ten permission of TOSHIBA. No patent liability is assumed, with respect to
the use of the information contained herein.
TOSHIBA Satellite C650/Satellite C650D/Satellite Pro C650/Satellite Pro
C650D Series Portable Personal Computer User’s Manual
First edition April 2010
Copyright authority for music, movies, computer programs, data bases and
other intellectual property covered by copyright laws belongs to the author
or to the copyright owner. Copyrighted material can be reproduced only for
personal use or use within the home. Any other use beyond that stipulated
above (including conversion to digital format, alteration, transfer of copied
material and distribution on a network) without the permission of the copy-
right owner is a violation of copyright or author’s rights and is subject to civil
damages or criminal action. Please comply with copyright laws in making
any reproduction from this manual.
Disclaimer
This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the TOSHIBA
Satellite C650/Satellite C650D/Satellite Pro C650/Satellite Pro C650D
Series Portable Personal Computer at the time of this manual’s production.
However, succeeding computers and manuals are subject to change
without notice. TOSHIBA assumes no liability for damages incurred directly
or indirectly from errors, omissions or discrepancies between the computer
and the manual.
Trademarks
IBM is a registered trademark, and IBM PC and PS/2 are trademarks of
International Business Machines Corporation.
Intel, Intel SpeedStep and Intel Core and Centrino are trademarks or regis-
tered trademarks of Intel Corporation or its subsidiaries in the United States
and other countries/regions.
AMD, the AMD Arrow logo, AMD Athlon, AMD Turion, Radeon, and combi-
nations thereof, ATI Mobility Radeon™ are trademarks of Advanced Micro
Devices, Inc.
Windows® and Microsoft are registered trademarks of Microsoft Corpora-
tion.
Photo CD is a trademark of Eastman Kodak.
ConfigFree is a trademark of Toshiba Corporation.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
User’s Manual i
Secure Digital and SD are trademarks of SD Card Association.
MultiMediaCard and MMC are trademarks of MultiMediaCard Association.
Labelflash™ is a trademark of YAMAHA CORPORATION.
Other trademarks and registered trademarks not listed above may be used
in this manual.
Safety Instructions
Use the following safety guidelines to help to protect yourself and your
computer.
Do not operate your portable computer for an extended period of time with
the base resting directly on your body. With extended operation, heat can
potentially build up in the base. Allowing sustained contact with the skin
could cause discomfort or, eventually, a burn.
User’s Manual ii
FCC Information
FCC Notice “Declaration of Conformity Information”
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
Only peripherals complying with the FCC class B limits may be attached to
this equipment. Operation with non-compliant peripherals or peripherals
not recommended by TOSHIBA is likely to result in interference to radio
and TV reception. Shielded cables must be used between the external
devices and the computer’s external monitor port, USB port, and
microphone jack. Changes or modifications made to this equipment, not
expressly approved by TOSHIBA or parties authorized by TOSHIBA could
void the user’s authority to operate the equipment.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Contact
Address: TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Telephone: (949) 583-3000
CE compliance
This product is labelled with the CE Mark in accordance with the related
European Directives, notably Electromagnetic Compatibility Directive
2004/108/EC for the notebook and the electronic accessories including the
supplied power adapter, the Radio Equipment and Telecommunications
Terminal Equipment Directive 1999/5/EC in case of implemented
telecommunication accessories and the Low Voltage Directive 2006/95/EC
for the supplied power adapter. Furthermore the product complies with the
Ecodesign Directive 2009/125/EC (ErP) and its related implementing
measures.
This product and the original options are designed to observe the related
EMC (Electromagnetic Compatibility) and safety standards. However,
TOSHIBA cannot guarantee that this product still observes these EMC
standards if options or cables not produced by TOSHIBA are connected or
implemented. In this case the persons who have connected/implemented
those options/cables have to provide assurance that the system (PC plus
options/cables) still fulfils the required standards. To avoid general EMC
problems, the following guidance should be noted:
■ Only CE marked options should be connected/implemented
■ Only best shielded cables should be connected
Working environment
This product was designed to fulfil the EMC (Electromagnetic Compatibility)
requirements to be observed for so-called “Residential, commercial and
light industry environments”. TOSHIBA do not approve the use of this
product in working environments other than the above mentioned
“Residential, commercial and light industry environments”.For example, the
following environments are not approved:
■ Industrial Environments (e.g. environments where a mains voltage of
380 V three-phase is used)
■ Medical Environments
■ Automotive Environments
■ Aircraft Environments
User’s Manual iv
Any consequences resulting from the use of this product in working
environments that are not approved are not the responsibility of
TOSHIBA.The consequences of the use of this product in non-approved
working environments may be:
■ Interference with other devices or machines in the near surrounding
area.
■ Malfunction of, or data loss from, this product caused by disturbances
generated by other devices or machines in the near surrounding area.
Therefore TOSHIBA strongly recommend that the electromagnetic
compatibility of this product should be suitably tested in all non-approved
working environments before use. In the case of automobiles or aircraft, the
manufacturer or airline respectively should be asked for permission before
use of this product.
Furthermore, for general safety reasons, the use of this product in
enviroments with explosive atmospheres is not permitted.
User’s Manual v
Following Information Is Only Valid for EU-member States
Disposal of Products
The crossed out wheeled dust bin symbol indicates that products must be
collected and disposed of separately from household waste. Integrated
batteries and accumulators can be disposed of with the product. They will
be separated at the recycling centres.
The black bar indicates that the product was placed on the market after
August 13, 2005.
By participating in separate collection of products and batteries, you will
help to assure the proper disposal of products and batteries and thus help
to prevent potential negative consequences for the environment and human
health.
For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.
The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from household
waste.
If the battery or accumulator contains more than the specified values of lead
(Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive
Pb, Hg,Cd (2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or
cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure
the proper disposal of products and batteries and thus help to prevent
potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.
This symbol may not be displayed depending on the country and region
where you purchased.
User’s Manual vi
Disposing of the Computer and the Computer's Batteries
■ Discard this computer in accordance with applicable laws and
regulations. For further information, contact your local government.
■ This computer contains rechargeable batteries. After repeated use, the
batteries will finally lose their ability to hold a charge and you will need
to replace them. Under certain applicable laws and regulation, it may be
illegal to dispose of old batteries by placing them in the trash.
■ Please be kind to our shared environment. Check with your local
government authority for details regarding where to recycle old batteries
or how to dispose of them properly. This product contains mercury.
Disposal of this material may be regulated due to environmental
considerations. For disposal, reuse or recycling information, please
contact your local government.
MANUFACTURED
Panasonic System Networks Co., Ltd.
1-62, 4-Chome Minoshima
Hakata-ku Fukuoka, Japan
User’s Manual ix
Toshiba Samsung Storage Technology
TS-L633C/TS-L633Y
MANUFACTURED
Hitachi-LG Data Storage, Inc.
22-23, Kaigan 3-chome, Minato-Ku,
Tokyo, 108-0022, Japan
User’s Manual x
TEAC
DV-W28S-V
User’s Manual xi
International Precautions
CAUTION: This appliance contains a
laser system and is classified as a
“CLASS 1 LASER PRODUCT.” To use
this model properly, read the instruction
manual carefully and keep this manual
for your future reference. In case of any
trouble with this model, please contact
your nearest “AUTHORIZED service
station.” To prevent direct exposure to the
laser beam, do not try to open the
enclosure.
VORSICHT: Dieses Gerät enthält ein
Laser-System und ist als
“LASERSCHUTZKLASSE 1 PRODUKT”
klassifiziert. Für den richtigen Gebrauch
dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch
und bewahren diese bitte als Referenz
auf. Falls Probleme mit diesem Modell
auftreten, benachrichtigen Sie bitte die
nächste “autorisierte Service-Vertretung”.
Um einen direkten Kontakt mit dem
Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.
ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af
klasse 1, hviket betyder, at der anvendes
laserstrlier af svageste klasse, og at man
ikke på apparatets yderside kan bilve
udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF
FAGFOLK MED SÆRLIGT KENDSKAB
TIL APPARATER MED
LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som
advarer imod at foretage sådanne
indgreb i apparatet, at man kan komme til
at udsatte sig for laserstråling.
Preface
General Precautions
Chapter 1 Getting Started
Equipment Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Connecting the AC Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Opening The Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Turning On The Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Starting Up for The First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Turning Off The Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Shut Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Hibernation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Restarting The Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
System Recovery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
System Recovery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
System Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Creating Recovery Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Restoring the pre-installed software from the Recovery hard disk drive
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Restoring the pre-installed software from your created Recovery Media
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Chapter 2 The Grand Tour
Front with The Display Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Left Side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Right Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Back Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Front with The Display Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
System Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
User’s Manual xv
Connecting the security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Chapter 4 Operating Basics
Using The Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Using The Web Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Using TOSHIBA Web Camera Application . . . . . . . . . . . . . . . . . . . . 4-4
Using The TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . 4-5
Note on Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
How to Register The Face Recognition Data . . . . . . . . . . . . . . . . . . 4-6
How to Delete The Face Recognition Data. . . . . . . . . . . . . . . . . . . . 4-7
How to Launch The Help File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Windows Logon Via TOSHIBA Face Recognition. . . . . . . . . . . . . . . 4-7
Using Optical Disc Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Loading Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Removing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Writing CD/DVDs on DVD Super Multi (±R DL) Drive . . . . . . . . . . . 4-12
Important Message (DVD Super Multi (±R DL) Drive) . . . . . . . . . . 4-12
Before Writing or Rewriting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
When Writing or Rewriting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Disclaimer (DVD Super Multi (±R DL) Drive) . . . . . . . . . . . . . . . . . 4-16
TOSHIBA Disc Creator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Data Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
How to Learn More about TOSHIBA Disc Creator . . . . . . . . . . . . . 4-17
TOSHIBA DVD PLAYER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
Notes on Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
Display Devices & Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Starting TOSHIBA DVD PLAYER . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Operating TOSHIBA DVD PLAYER . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Open TOSHIBA DVD PLAYER HELP. . . . . . . . . . . . . . . . . . . . . . . 4-20
Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
CD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Sound System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Adjusting System Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Changing System Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Smart Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Using The Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Wireless Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
Wireless Communication Hot key . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
LAN Cable Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
Connecting LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
Disconnecting LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Manual Contents
This manual is composed of the following chapters, appendixes, a glossary
and an index.
Chapter 1, Getting Started, is an overview of the computer’s features,
capabilities, and options.
Chapter 2, The Grand Tour, identifies the components of the computer and
briefly explains how they function.
Chapter 3, Hardware, Utilities and Options, provides a quick overview of
how to begin operating your computer.
Chapter 4, Operating Basics, includes tips on care of the computer and on
using the touchpad,optical disc drive, Audio/Video controls, the web
camera, the microphone, wireless communication and LAN.
Conventions
This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.
Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parenthesis following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.
Icons
Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.
Keys
The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, ENTER identifies the Enter key.
Key Operation
Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign
(+). For example, CTRL + C means you must hold down CTRL and at the
same time press C. If three keys are used, hold down the first two and at
the same time press the third.
User’s Manual xx
Preface
Display
Messages
Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.
Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.
Please read. A note is a hint or advice that helps you make best use of
your equipment.
Terminology
This term is defined in this document as follows:
Start
The word “Start” refers to the “ ” button in
Windows® 7.
To keep your computer in prime operating condition, protect your work area
from:
■ Dust, moisture, and direct sunlight.
■ Equipment that generates a strong electromagnetic field, such as
stereo speakers (other than speakers that are connected to the
computer) or speakerphones.
■ Rapid changes in temperature or humidity and sources of temperature
change such as air conditioner vents or heaters.
■ Extreme heat, cold, or humidity.
■ Liquids and corrosive chemicals.
Stress Injury
Carefully read the Instruction Manual for Safety and Comfort. It contains
information on the prevention of stress injuries to your hands and wrists
that can be caused by extensive keyboard use. Instruction Manual for
Safety and Comfort also includes information on work space design,
posture and lighting that can help reduce physical stress.
Heat Injury
■ Avoid prolonged physical contact with the computer. If the computer is
used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time, for example if you rest the
computer on your lap or if you keep your hands on the palm rest, your
skin might suffer a low-heat injury.
■ If the computer has been used for a long time, avoid direct contact with
the metal plate supporting the various interface ports as this can
become hot.
■ The surface of the AC adaptor can become hot when in use but this
condition does not indicate a malfunction. If you need to transport the
AC adaptor, you should disconnect it and let it cool before moving it.
■ Do not lay the AC adaptor on a material that is sensitive to heat as the
material could become damaged.
Mobile Phones
Please be aware that the use of mobile phones can interfere with the audio
system. The operation of the computer will not be impaired in any way, but
it is recommended that a minimum distance of 30cm is maintained between
the computer and a mobile phone that is in use.
Getting Started
Equipment Checklist
Carefully unpack your computer. Save the box and packaging materials for
future use.
Hardware
Check to make sure you have all the following items:
■ Satellite C650/Satellite C650D/Satellite Pro C650/Satellite Pro C650D
Series Portable Personal Computer
■ Battery pack
■ AC adaptor and power cord (2-pin plug or 3-pin plug)
Documentation
■ User's Manual
■ Instruction Manual for Safety and Comfort
If any of the items are missing or damaged, contact your dealer
immediately.
Software
Windows 7
The following software is preinstalled:
■ Windows 7
■ Display Drivers for Windows
■ LAN Driver
■ Pointing Device Driver
■ Sound Driver for Windows
■ Wireless LAN driver
■ TOSHIBA Assist
■ TOSHIBA ConfigFree
■ TOSHIBA Disc Creator
■ TOSHIBA DVD PLAYER (Is preinstalled with some models)
■ TOSHIBA Face Recognition (Is preinstalled with some models)
■ TOSHIBA User’s Manual
■ TOSHIBA Value Added Package
■ TOSHIBA Bulletin Board
■ TOSHIBA ReelTime
■ TOSHIBA Recovery Media Creator
■ TOSHIBA Media Controller
Getting Started
■ All users should be sure to read the section Starting Up for The First
Time.
■ Be sure to read the enclosed Instruction Manual for Safety and Comfort
for information on the safe and proper use of this computer. It is
intended to help you be more comfortable and productive while using a
notebook computer. By following the recommendations in it you may
reduce your chance of developing a painful or disabling injury to your
hand, arms, shoulders or neck.
■ Restoring the pre-installed software from the Recovery hard disk drive
■ Restoring the pre-installed software from your created Recovery Media
If you are a new user, follow the steps in each section of this chapter as you
prepare to operate your computer
■ Always use the TOSHIBA AC adaptor that was included with your
computer or use AC adaptors specified by TOSHIBA to avoid any risk
of fire or other damage to the computer. Use of an incompatible AC
adaptor could cause fire or damage to the computer possibly resulting
in serious injury. TOSHIBA assumes no liability for any damage caused
by use of an incompatible adaptor.
■ Never plug the AC adaptor into a power source that does not
correspond to both the voltage and the frequency specified on the
regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.
■ Always use or purchase power cables that comply with the legal
voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
resulting in serious injury.
■ The supplied power cord conforms to safety rules and regulations in
the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.
■ Do not use a 3-pin to 2-pin conversion plug.
■ When you connect the AC adaptor to the computer, always follow the
steps in the exact order as described in the User’s Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical charge
and cause an electrical shock or minor bodily injury when touched. As
a general safety precaution, avoid touching any metal parts.
■ Never place your computer or AC adaptor on a wooden surface,
furniture, or any other surface that could be marred by exposure to heat
since the computer base and AC adaptor's surface increase in
temperature during normal use.
■ Always place your computer or AC adaptor on a flat and hard surface
that is resistant to heat damage.
Refer to the enclosed Instruction Manual for Safety and Comfort for
detailed precautions and handling instructions.
Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug)
Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug)
3. Plug the power cord into a live wall outlet - the DC IN/Battery indicator
on the front of the computer should glow.
Use reasonable care when opening and closing the display panel. Opening
it vigorously or slamming it shut could damage the computer.
■ Be careful not to open the display panel too far as this could put stress
on the display panel’s hinges and cause damage.
■ Do not press or push on the display panel.
■ Do not lift the computer by the display panel.
■ Do not close the display panel with pens or any other objects left in
between the display panel and the keyboard.
■ When opening or closing the display panel, place one hand on the
palm rest to hold the computer in place and use the other hand to
slowly open or close the display panel (Do not use excessive force
when opening or closing the display panel).
1.POWER BUTTON
1. If you have entered data, either save it to the hard disk drive or to
other storage media.
2. Make sure all disk/disc activity has stopped before removing the
CD/DVD or floppy diskette.
■ Make sure the Optical Disc Drive indicator is off. If you turn off the
power while a disk (disc) is being accessed, you may lose data or
damage the disk.
■ Never turn off the power while an application is running. Doing so
could cause loss of data.
■ Never turn off the power, disconnect an external storage device or
remove storage media during data read/write. Doing so can cause data
loss.
3. Click Start.
4. Click the Shut down button ( ).
5. Turn off any peripheral devices connected to your computer.
Sleep Mode
If you have to interrupt your work, you are able to turn off the power without
exiting from your software by placing the computer into Sleep Mode. In this
mode data is maintained in the computer's main memory so that when you
turn on the power again, you can continue working right where you left off.
When you have to turn off your computer aboard an aircraft or in places
where electronic devices are regulated or controlled, always completely
shut down the computer. This includes turning off any wireless
communication functionalities and cancelling settings that reactivate the
computer automatically, such as a timer recording function. Failure to
completely shut down the computer in this way could allow the operating
system to reactivate and run pre-programmed tasks or preserve unsaved
data, which could interfere with aviation or other systems, possibly causing
serious injury.
■ When the computer is shut down in Sleep Mode, the power indicator
will blink amber.
■ If you are operating the computer on battery power, you can lengthen
the overall operating time by turning it off into Hibernation Mode - Sleep
Mode will consume more power while the computer is off.
Hibernation Mode
The Hibernation Mode feature saves the contents of memory to the hard
disk drive when the computer is turned off so that, the next time it is turned
on, the previous state is restored. Please note that the Hibernation Mode
feature does not save the status of any peripheral devices connected to the
computer.
■ Save your data. While entering Hibernation Mode, the computer saves
the contents of memory to the hard disk drive. However, for safety
sake, it is best to save your data manually.
■ Data will be lost if you remove the battery or disconnect the AC adaptor
before the save is completed. Wait for the Optical Disc Drive indicator
to go out.
■ Do not install or remove a memory module while the computer is in
Hibernation Mode. Data will be lost.
■ Press the power button and hold it down for five seconds. Once the
computer has turned itself off, wait between ten and fifteen seconds
before turning the power on again by pressing the power button.
System Recovery
This section describes the creation of Recovery Media and their use.
When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.
When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.
1. Load the Recovery Media into the computer and turn off the compu-
ter's power.
2. While holding down F12 key on the keyboard, turn on your computer -
when the TOSHIBA Leading Innovation>>> logo screen
appears, release the F12 key.
3. Use the up and down cursor key to select the appropriate option from
the menu according to your actual recovery media. Please refer to the
Boot Priority section in Chapter 7, HW Setup and Passwords for fur-
ther information.
4. A menu will be displayed from which you should follow the on-screen
instructions
Bridge media slot This slot allows you to easily transfer data from
devices, such as digital camera and PDA, that
use flash memory (Secure Digital (SD)/Secure
Digital High Capacity (SDHC)/Secure Digital
Extended Capacity (SDXC) /MultiMediaCard
(MMC)).
Left Side
Figure 2-2 shows the computer’s left side.
Be careful not to block the fan vent. Also be careful to keep foreign objects
out of the vents. A pin or similar object can damage the computer’s
circuitry.
■ Do not connect any cable other than a LAN cable to the LAN jack. It
could cause damage or malfunction.
■ Do not connect the LAN cable to a power supply. It could cause
damage or malfunction.
Universal serial bus Two universal serial bus (USB) ports comply with
(USB 2.0) ports USB 2.0 standards, which enable data transfer
speeds 40 times faster than the USB 1.1
standards.
Keep foreign objects out of the USB connectors. A pin or similar object can
damage the computer’s circuitry.
Operation of all functions of all USB devices has not been confirmed.
Some functions might not execute properly.
Right Side
Figure 2-3 shows the computer’s right side.
Back Side
Figure 2-4 shows the computer’s back side.
Underside
Figure 2-5 shows the underside of the computer. Make sure the display is
closed before turning over your computer.
1.BATTERY PACK
2.BATTERY PACK LOCK
3.BATTERY RELEASE LATCH
4.MEMORY MODULE COVER
Battery pack The battery pack powers the computer when the
AC adaptor is not connected. The Batteries
section in Chapter 6, Power and Power-up
Modes, describes how to access the battery
pack. Additional battery packs can be purchased
from your TOSHIBA dealer to extend the
computer’s battery operating time.
Battery pack lock Slide the battery pack lock to unlocked position to
free the battery release latch.
Battery release latch Slide this latch to release the battery pack.
This latch moves only when the computer is
upside down.
Web camera LED The web camera LED glows blue when the web
camera software is used. (Provided with some
models)
System Indicators
Figure 2-7 shows the system indicators, which light when various computer
operations are in progress.
1.DC IN/BATTERY
2.POWER
Keyboard Indicators
The figure below shows the position of the CAPS LOCK indicator and the
NUM LOCK indicator which show the following conditions:
■ When the CAPS LOCK indicator glows, the keyboard is in all-caps
mode.
■ When the NUM LOCK indicator glows, the ten key allows you to enter
numbers.
CAPS LOCK This indicator glows green when letter keys are
locked into their uppercase format.
NUM LOCK When the NUM LOCK indicator glows, you can
use the number keys on the keyboard for number
entry.
DVD
DVD drive and their media are manufactured according to the
specifications of six marketing regions. When you purchase DVD-Video,
make sure it matches your drive, otherwise it will not play properly.
Code Region
1 Canada, United States
2 Japan, Europe, South Africa, Middle East
3 Southeast Asia, East Asia
4 Australia, New Zealand, Pacific Islands, Central America,
South America, Caribbean
5 Russia, Indian Subcontinent, Africa, North Korea,
Mongolia
6 China
Writable Discs
This section describes the types of writable CD/DVD discs. Check the
specifications for your drive to for the type of discs it can write. Use
TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4,
Operating Basics.
CDs
■ CD-R discs can be written only once. The recorded data cannot be
erased or changed.
■ CD-RW discs can be recorded more than once.
DVDs
■ DVD-R, DVD+R, DVD-R DL and DVD+R DL discs can be written only
once. The recorded data cannot be erased or changed.
■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than
once.
AC Adaptor
The AC adaptor converts AC power to DC power and reduces the voltage
supplied to the computer. It can automatically adjust to any voltage from
100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to
use the computer in almost any region.
To recharge the battery, simply connect the AC adaptor to a power source
and the computer. See Chapter 6 Power and Power-up Modes for details.
Always use the TOSHIBA AC adaptor that was included with your
computer, or use AC adaptors specified by TOSHIBA to avoid any risk of
fire or other damage to the computer. Use of an incompatible AC adaptor
could cause fire or damage to the computer possibly resulting in serious
injury. TOSHIBA assumes no liability for any damage caused by use of an
incompatible adaptor.
Hardware
This section describes the hardware of your computer.
The actual specifications may vary depending on the model you
purchased.
Processor*1
Built-in Your computer is equipped with one processor
and processor type varies depending on model.
To check which type of processor is included in
your model, open the TOSHIBA PC Diagnostic
Tool Utility by clicking Start → All Programs →
TOSHIBA → Utilities → PC Diagnostic Tool.
Memory*2
Disks
Hard Disk Drive The computer is equipped with a Hard Disk Drive
(HDD)*4 (HDD) for nonvolatile storage of data and
software.(Depending on the model you
purchased)
■ HDD
■ 250 GB
■ 320 GB
■ 500 GB
Please note that part of the hard disk drive’s
overall capacity is reserved as administration
space.
DVD Super Multi (±R Some models are equipped with a full-size DVD
DL) Drive Super Multi (± R DL) drive module that allows you
to record data to rewritable CD/DVDs as well as
run CD/DVDs without using an adaptor. It reads
DVD-ROMs at maximum 8 speed and CD-ROMs
at maximum 24 speed. It writes CD-R at up to 24
speed, CD-RW at up to 24 speed, DVD-R at up to
8 speed, DVD-RW at up to 6 speed, DVD-RAM at
up to 5 speed, DVD+R at up to 8 speed,
DVD+RW at up to 8 speed, DVD+R DL at up to 6
speed and DVD-R DL at up to 6 speed. This drive
supports the following formats:
■ DVD-ROM
■ DVD-Video
■ DVD-R
■ DVD-RW
■ DVD+R
■ DVD+RW
■ DVD-RAM
■ DVD+R DL
■ DVD-R DL
■ CD-DA
■ CD-Text
■ CD-R
■ CD-RW
■ CD-ROM Mode 1, Mode 2
■ CD-ROM XA Mode 2 (Form1, Form2)
■ CD-G (Audio CD only)
■ Photo CD (single/multi-session)
■ Enhanced CD (CD-EXTRA)
■ Addressing Method 2
Display
The computer's internal display panel supports high-resolution video
graphics and can be set to a wide range of viewing angles for maximum
comfort and readability.
AMD® Vari-BrightTM
Your model may include the AMD® Vari-BrightTM feature that can save the
computer's power consumption by optimizing picture contrast on the
internal LCD. This feature can be used if the computer is:
■ running under battery mode.
■ using the internal LCD display only
The power and performance settings can be adjusted in the Catalyst
Control Center.To access this utility, go to
Start → All Programs → Catalyst Control Center → CCC - Advanced →
Enable Vari-BrightTM
If you want to improve the picture quality under the conditions mentioned
above, adjust the setting towards Maximum Quality or disable this feature.
Keyboard
Pointing Device
Power
RTC battery The internal RTC battery backs up the Real Time
Clock (RTC) and calendar.
Ports
Headphone Enables connection of a stereo headphone.
Universal Serial Bus Two Universal Serial Bus (USB) enable a chain
(USB 2.0) ports connection of USB-equipped devices to your
computer through the ports.
Slots
Bridge media slot This slot allows you to easily transfer data from
devices, such as digital cameras and Personal
Digital Assistants, that use flash memory (Secure
Digital (SD)/Secure Digital High Capacity
(SDHC)/Secure Digital Extended Capacity
(SDXC)/MultiMediaCard (MMC)). see Bridge
Media Slot in this Chapter for details.
Multimedia
Communications
Security
Software
Operating system Windows 7 is available. Refer to the preinstalled
Software section at the Chapter 1, Getting
Started.
TOSHIBA Utilities A number of utilities and drivers are preinstalled
to make your computer more convenient to use.
Refer to the TOSHIBA Value Added Package and
Utilities and Applications sections in this chapter.
Plug and Play When you connect an external device to the
computer or when you install a component, Plug
and Play capability enables the system to
recognize the connection and make the
necessary configurations automatically.
Special Features
The following features are either unique to TOSHIBA computers or are
advanced features which make the computer more convenient to use. To
access the Power Options, click Start → Control Panel → System and
Maintenance → Power Options.
Hot keys Key combinations allow you to quickly modify the
system configuration directly from the keyboard
without running a system configuration program.
Battery save mode This feature allows you to configure the computer
in order to save battery power. This can be
specified in the Power Options.
Panel power on/off This feature turns power to the computer off
when the display panel is closed and turns it
back on when the panel is opened. This can be
specified in the Power Options.
Options
You can add a number of options to make your computer even more
powerful and convenient to use. The following options are available:
Memory expansion Two memory expansion slots are available for
installing PC2-6400, PC3-8500 1 GB, 2 GB or
4 GB memory modules of all models.
■ Maximum size of memory can be installed on
Mobile Intel® GL40 Express Chipset models
is 4 GB.
■ Maximum system memory size and speed
are depending on the model you purchased.
USB FDD kit The USB floppy disk drive accommodates either
a 1.44 MB or 720 KB floppy disk through
connection to one of the computer’s USB ports.
In use, please be aware that, while you cannot
format 720 KB floppy disks under Windows 7,
you are able to read and write to disks that have
already been formatted.
Optional Devices
Optional devices can expand the computer’s capabilities and its versatility.
The following optional devices are available from your TOSHIBA dealer:
Cards/Memory
■ Memory cards: Secure Digital (SD), Secure Digital High Capacity
(SDHC), Secure Digital Extended Capacity (SDXC) and
MultiMediaCard (MMC)
■ Memory expansion
Power Devices
■ Additional battery pack (3 cell and 6 cell)
■ Additional AC adaptor
Peripheral Devices
■ USB FDD Kit
■ External monitor
Other
■ Security lock
Memory Media
This section provides the important safety precautions in order to handle
your memory media.
Should you need to format all areas of the memory card, including the
protected area, you will need to obtain an appropriate application that
applies the copy protection system.
Media Care
Observe the following precautions when handling the card.
Card Care
■ Do not twist or bend cards.
■ Do not expose cards to liquids or store in humid areas or lay media
close to containers of liquid.
■ Do not touch the metal part of a card or expose it to liquids or let it get
dirty.
■ After using card, return it to its case.
■ The card is designed so that it can be inserted only one way. Do not try
to force the card into the slot.
■ Do not leave a card partially inserted in the slot. Press the card until you
hear it click into place.
■ When inserting memory media, do not touch the metal contacts. You
could expose the storage area to static electricity, which can destroy
data.
■ Do not turn the computer off or switch to Sleep Mode or Hibernation
Mode while files are being copied - doing so may cause data to be lost.
■ If you remove the memory media or turn off the power while the
computer is accessing the memory media, you may lose data or
damage the media.
■ Do not remove the memory media while the computer is in Sleep or
Hibernation Mode. The computer could become unstable or data in the
memory media could be lost.
■ Do not remove only the miniSD/microSD Card while leaving the
adaptor in the Bridge Media slot.
Memory Expansion
You can install additional memory in the computer’s memory module to
increase the amount of RAM.
■ If you use the computer for a long time, the memory modules will
become hot. In this case, let the memory modules cool to room
temperature before you replace them.
■ Do not try to install a memory module with the computer turned on or
turned off in Sleep and Hibernation Mode. You can damage the
computer and the memory module.
6. Insert the memory module into the connector on the computer. Press
the module carefully and firmly to ensure a solid connection.
7. Push the module down so that it lies flat and is secured by two
latches.
■ If you use the computer for a long time, the memory modules will
become hot. In this case, let the memory modules cool to room
temperature before you replace them.
■ Do not try to remove a memory module with the computer turned on or
turned off in Sleep and Hibernation Mode. You can damage the
computer and the memory module.
2. Turn the computer upside down and remove the battery pack (refer to
Chapter 6, Power and Power-up Modes.)
3. Remove one screw securing the memory module cover.
4. Lift off the cover.
5. Use a slender object such as a pen to press two latches on either side
of the memory module to the outside. The memory module will pop
up.
6. Grasp the memory module by the sides and pull it out.
Additional AC Adaptor
If you frequently transport the computer between different sites such as
your home and office, purchasing an AC adaptor for each location will
reduce the weight and bulk of your carrying load.
External Monitor
An external analog monitor can be connected to the external monitor port
on the computer.To connect a monitor, follow the steps as detailed below:
Figure 3-8 Connecting the monitor cable to the external monitor port
Security Lock
A security lock enables you to anchor your computer to a desk or other
heavy object to help prevent unauthorized removal of the computer.
Attach one end of a cable to the desk and the other end to the security lock
slot on the right side of the computer.
1.SECURITY LOCK
2.KEY
Operating Basics
1.BUILT-IN MICROPHONE
2.WEB CAMERA LED
3.WEB CAMERA LENS
1.CAPTURE SETTINGS
2.CAMERA RESOLUTION
3.CAPTURE STILL IMAGE
4.VIDEO RECORDING
5.OPEN/CLOSE PREVIEW AREA
6.DELETE RECORDED FILE
Note on Use
■ TOSHIBA Face Recognition does not guarantee the correct
identification of a user. Changes to the likeness of a registrant, such as
hair style changes, wearing a cap, or wearing glasses may effect the
recognition rates when such changes occur after the registrant had
registered.
■ TOSHIBA Face Recognition may incorrectly recognize faces that are
similar to a registrant.
■ For high security purposes, TOSHIBA Face Recognition is not a
suitable substitute for Windows passwords. When security is a high
priority, use your established Windows passwords to log in.
■ Bright background light and/or shadows may prevent a registrant from
being recognized correctly. In that case, log in using your Windows
password. If recognition of a registrant fails repeatedly, refer to your
computer documentation to learn ways to improve recognition
performance.
■ TOSHIBA Face Recognition records face data in a log when face
recognition fails. When transferring ownership or disposing of your
computer, please uninstall the application or delete all the logs created
by the application. For details on how to do this, see help file.
■ TOSHIBA Face Recognition can be used only in Windows Vista and
Windows 7.
Disclaimer
TOSHIBA does not guarantee that the face recognition utility technology
will be completely secure or error-free. TOSHIBA does not guarantee that
the face recognition utility will accurately screen out unauthorized users at
all times. TOSHIBA is not liable for any failure or damage that might arise
out of the use of the face recognition software or utility.
TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO
RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS,
PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE
STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE
OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF.
Please also refer to the Writing CD/DVDs on DVD Super Multi (±R DL)
Drive section for precautions on writing to CD/DVDs.
Loading Discs
Please follow the steps below and refer to figures.
1. a. When the power is on, press the eject button to open the drawer
slightly.
1.EJECT BUTTON
b. Pressing the eject button will not open the drawer when the drive’s
power is off. If the power is off, you can open the drawer by insert-
ing a slender object (about 15 mm) such as a straightened paper
clip into the eject hole just to the right of the eject button.
1.EJECT HOLE
When the drawer is fully opened, the edge of the computer will extend
slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD
at an angle when you place it in the tray. After seating the CD/DVD,
however, make sure it lies flat, as shown in above figure.
4. Press gently at the center of the CD/DVD until you feel it click into
place. The CD/DVD should lie below the top of the spindle, flush with
the spindle base.
5. Push the center of the drawer to close it. Press gently until it locks into
place.
If the CD/DVD is not seated properly when the drawer is closed, the
CD/DVD might be damaged. Also, the drawer might not open fully when
you press the eject button.
Removing Discs
To remove the CD/DVD, follow the steps below and refer to below figure.
Do not press the eject button while the computer is accessing the drive.
Wait for the optical disc drive indicator to go out before you open the
drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for
it to stop before you remove it.
■ When the drawer pops open slightly, wait a moment to make sure the
CD/DVD has stopped spinning before pulling the drawer fully open.
■ Turn off the power before you use the eject hole. If the CD/DVD is
spinning when you open the drawer, the CD/DVD could fly off the
spindle and cause injury.
2. The CD/DVD extends slightly over the sides of the drawer so you can
grasp it. Hold the CD/DVD gently and lift it out.
3. Push the center of the drawer to close it. Press gently until it locks into
place.
CD-R:
TAIYO YUDEN CO., LTD.
MITSUBISHI KAGAKU MEDIA CO., LTD.
HITACHI MAXELL LTD.
CD-RW: (Ultra-Speed)
MITSUBISHI KAGAKU MEDIA CO., LTD.
DVD-R:
DVD Specifications for Recordable Disc for General Version 2.0
TAIYO YUDEN CO., LTD. (for 8x and 16x speed media)
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed
media)
HITACHI MAXELL LTD. (for 8x and 16x speed media)
DVD+R:
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed
media)
TAIYO YUDEN CO., LTD. (for 8x and 16x speed media)
DVD-RW:
DVD Specifications for Recordable Disc for General Version 1.1 or
Version 1.2
VICTOR COMPANY OF JAPAN, LTD. (JVC) (for 2x, 4x and 6x speed
media)
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2x, 4x and 6x speed
media)
DVD+RW:
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x, 4x and 8x speed
media)
DVD-RAM:
DVD Specifications for Recordable Disc for General Version 2.0,
Version 2.1 or Version 2.2
Panasonic CORPORATION. (for 3x and 5x speed media)
HITACHI MAXELL LTD. (for 3x and 5x speed media)
This DVD Super Multi (±R DL) drive cannot use discs that allow writing
faster than 16x speed(DVD-R and DVD+R media), 8x speed DVD-
R(Double layer),DVD+RW, and DVD+R(Double layer) media, 6x
speed(DVD-RW media), 5x speed (DVD-RAM media).
Data Verification
To verify that data has been written or rewritten correctly to a data CD/DVD
you should follow the steps below before you begin the write/rewrite
process:
1. Display the setting dialog box by one of the following two steps:
■ Click the Recording settings button ( ) for writing on the main
toolbar in the Data CD/DVD mode.
■ Select Settings for Each Mode → Data CD/DVD in the Settings
menu.
2. Mark the Verify written data check box.
3. Select File Open or Full Compare mode.
4. Click the OK button.
Notes on Use
■ "TOSHIBA DVD PLAYER" software is supported for playback of DVD-
Video and DVD-VR.
■ Frame dropping, audio skipping or out of synch audio and video may
occur during playback of some DVD-Video titles.
■ Close all other applications when using the “TOSHIBA DVD PLAYER”.
Do not open any other applications or carry out any other operations
during DVD-Video playback. Playback may stop or not function properly
in some situations.
■ Unfinalized DVDs created on home DVD recorders may not be playable
on the computer.
■ Use DVD-Video discs with a region code which is either “the same as
the factory default setting” or “ALL”.
■ Do not playback DVD discs Video while watching or recording television
programs using other applications. Doing so may cause DVD-Video
playback or television program recording errors. In addition, if
prescheduled recording starts during DVD-Video playback it may cause
DVD-Video playback or television program recording errors. Please
view DVD-Video during times when there is no recording prescheduled.
■ The resume function cannot be used with some discs on the “TOSHIBA
DVD PLAYER”.
■ It is recommended the AC adaptor be connected when playing DVD-
Video. Power saving features may interfere with smooth playback.
When playing DVD-Video using battery power, set the Power Options to
“Balance“.
■ Screen savers will not display while playing a movie in the "TOSHIBA
DVD PLAYER". The computer will also not go into Sleep Mode,
Hibernation Mode or Shut Down while using "TOSHIBA DVD PLAYER.
■ Do not configure the Display automatic power off function to run while
the “TOSHIBA DVD PLAYER” is running.
■ Do not switch to Hibernation or Sleep Mode when running the
“TOSHIBA DVD PLAYER”.
■ Do not lock the computer using the Windows logo( ) + L keys or
the FN + F1 keys when running the “TOSHIBA DVD PLAYER”.
■ Do not change Windows Users while "TOSHIBA DVD PLAYER" is
running.
■ The "TOSHIBA DVD PLAYER" does not have a parental control
function.
■ In order to protect copyrights, the Windows Print Screen function is
disabled when "TOSHIBA DVD PLAYER" is running.
Media Care
This section provides tips on protecting data stored on your CD/DVD.
Handle your media with care. The following simple precautions will
increase the lifetime of your media and protect the data stored on them.
CD/DVD
1. Store your CD/DVD in the container they came in to protect them and
keep them clean.
2. Do not bend the CD/DVD.
3. Do not write on, apply a sticker to, or otherwise mark the surface of the
CD/DVD that contains data.
4. Hold the CD/DVD by its outside edge or the edge on the center hole.
Fingerprints on the surface can prevent the drive from properly reading
data.
5. Do not expose to direct sunlight, extreme heat or cold.
6. Do not place heavy objects on your CD/DVD.
7. If your CD/DVD become dusty or dirty, wipe them with a clean dry
cloth. Wipe from the center out, do not wipe in a circular direction
around the CD/DVD. If necessary, use a cloth dampened in water or a
neutral cleaner. Do not use benzine, thinner or similar cleaner.
Sound System
This section describes some of the audio control functions.
Smart Audio
You can confirm and change the audio configuration using the Smart
Audio. To launch the Smart Audio, click Start → Control Panel →
Hardware and Sound → Smart Audio. When you first launch the Smart
Audio, you will see following device tabs.
Volume Mixer
Displays all connected audio devices in the system. Every device has a
Volume Slider Bar and a Mute button.
Clicking once on a device will select and highlight it. On Windows 7, double
clicking will make it the default device, which is denoted by a green
checkmark.
Voice Effects
Controls Voice Recording and Voice Over IP (VOIP) phone conversation
settings.
■ Voice Recording - Microphone Noise Reduction effect will be enabled
to suppress background noise and project a clear voice. To select /
deselect this setting, click on the Voice Recording icon.
■ Voice Over IP - In addition to Microphone Noise Reduction, Speaker
Noise Reduction and Acoustic Echo Cancellation effects will also be
enabled to remove disturbances caused by sound echo. To select /
deselect this setting, click on the Voice Over IP icon.
Audio Director
Allows you to define how sound is directed to devices. There are two
modes to select: Classic and Multi-Stream.
■ Classic mode - Emulates the behavior of Microsoft Windows XP, where
sound is heard either on the speakers or on the headphones, but not
both at the same time. To select Classic mode, click on the
corresponding icon.
■ Multi-Stream - Different sounds can be played on speakers and
headphones simultaneously. To select Multi-Stream mode, click on the
corresponding icon.
Two "Play" buttons allow you to play separate sounds in both modes:
■ When the red Play button is pressed, a sample sound is played on the
headphones.
■ When the blue Play button is pressed, a different sample sound is
played on the speakers.
In Classic mode, if the headphones are plugged in, both red and blue
sounds are heard from the headphones and if they are unplugged, both red
and blue sounds are heard from the speakers.
In Multi-Stream mode, the red sound is only played on the headphones
and the blue sound is only played on the speakers.
2. Click on the Jazz button and you will immediately hear how the Jazz
profile enhances the music output on the speakers.
3. To disable the selected profile, click on the OFF button.
■ Custom - Profiles will be created when you adjust the Equalizer Bars
below the preset icons.
■ Night Mode - An option that boosts vocal clarity while maintaining
background sound quality. It brings up the volume for subtle sounds like
whispers while suppressing the volume of loud sounds like explosions.
Night Mode allows you to hear details in soundtracks of high energy
sound sources without making the volume louder and potentially
disturbing others, which is especially useful for late-night viewing.
Two additional effects are offered on this page that apply to stereo
speakers only and are disabled for headphones and mono speaker.
■ Phantom Speakers - Gives you a closer-to-live experience when you
are watching a movie or listening to concert music. If you sit between
the internal speakers, the sound you hear will appear to be coming from
sources around you, rather than just from the speakers on the PC.This
option is ON by default when the Concert profile is selected.
■ 3D Immersion - Gives you a headphone experience without actually
wearing one. The effect is particularly useful when you are listening to
Voice. This option is ON by default if the Voice profile is selected.
You can adjust the level of the Phantom Speakers and 3D Immersion
effects from "None" to "Expanded" by adjusting the Slider Bar under their
corresponding icons. For Phantom Speakers, your selection will be
depicted by the position of speakers and the opacity of the glow around the
speakers and the rays emanating from them. For 3D Immersion, your
selection will be depicted by a circle around the PC that will get dimmer or
brighter with the movement of the Slider Bar.
Wireless Communications
The computer’s wireless communication function supports some wireless
communication devices.
Wireless LAN
The Wireless LAN is compatible with other LAN systems based on Direct
Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing
radio technology that complies with IEEE 802.11 Wireless LAN standard
(Revision B, G or N).
Setting
1. Please make sure that the Wireless Communication function is on.
2. Click Start → Control Panel → Network and Internet → Network
and Sharing Center.
3. Click Set up a new connection or network.
4. Follow the wizard. You will need the name of the wireless network
together with security settings. Consult the documentation accompa-
nied with your router or ask your wireless network administrator for the
settings.
Security
■ Be sure to enable encryption function. Otherwise your computer will
allow the illegal access by outsider through Wireless LAN to cause
illegal instruction, eavesdropping, and loss or destruction of stored data.
TOSHIBA strongly recommends the customer to enable the encryption
function.
■ TOSHIBA is not liable for the eavesdropping of data due to the use of
Wireless LAN and the damage thereof.
Turn the computer off when you enter an airplane and check the carrier’s
regulations before you use a computer on board.
LAN
The computer has built-in support for Fast Ethernet (10BASE-T/100BASE-
TX). This section describes how to connect/disconnect to a LAN.
Do not install or remove an optional memory module while Wake-up on
LAN is enabled.
The Wake-up on LAN function consumes power even when the system is
off. Leave the AC adaptor connected while using this feature.
If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-
TX), be sure to connect with a CAT5 cable or higher. You cannot use a
CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you
can connect with a CAT3 or higher cable.
1.LAN JACK
3. Plug the other end of the cable into a LAN hub connector. Check with
your LAN administrator before connecting to a hub.
Heat Dispersal
To protect from overheating, the CPU has an internal temperature sensor. If
the computer’s internal temperature rises to a certain level, the cooling fan
is turned on or the processing speed is lowered. You can select whether to
control the CPU temperature by turning on the fan first, then if necessary,
lowering the CPU speed. Or, turns on fan first, if necessary lowers CPU
processing speed earlier than at Maximum Performance Mode for long
battery life. These functions are controlled within the Power Options.
When the CPU temperature falls to a normal range, the fan is turned off
and the CPU operation returns to standard speed.
If the CPU temperature reaches an unacceptably high level with either
setting, the system automatically shuts down to prevent damage. Data in
memory will be lost.
The Keyboard
Typewriter Keys
The typewriter keys, produce the uppercase and lowercase letters,
numbers, punctuation marks, and special symbols that appear on the
screen.
There are some differences, however, between using a typewriter and
using a computer keyboard:
■ Letters and numbers produced in computer text vary in width. Spaces,
which are created by a “space character,” may also vary depending on
line justification and other factors.
■ The lowercase l (el) and the number 1 (one) are not interchangeable on
computers as they are on a typewriter.
■ The uppercase O (oh) and the 0 (zero) are not interchangeable.
■ The CAPS LOCK function key locks only the alphabetic characters in
uppercase while the shift lock on a typewriter places all keys in the
shifted position.
■ The SHIFT keys, the TAB key, and the BACK SPACE key perform the
same function as their typewriter counterparts but also have special
computer functions.
Function Keys: F1 … F9
The function keys, not to be confused with FN, are the 9 keys at the top of
your keyboard. These keys are dark gray, but function differently from the
other dark gray keys.
Hot Keys
Hot keys (pressing FN + a function or ESC key) allow you to enable or
disable certain features of the computer.
If your wireless communication device is not installed, a dialog box will not
appear.
FN Sticky Key
To motive the TOSHIBA Accessibility Utility , you can press FN sticky key
once and then press any ”F number”.
To start the TOSHIBA Accessibility Utility, click Start → All Programs →
TOSHIBA → Utilities → Accessibility.
Power Conditions
The computer’s operating capability and battery charge status are affected
by the power conditions: whether an AC adaptor is connected, whether a
battery is installed and what the charge level is for the battery.
Power conditions Table
No battery • No operation
installed • DC IN/Battery LED:off
System Indicators
The DC IN/Battery and Power indicators on the system indicator panel
alert you to the computer’s operating capability and battery charge status.
DC IN/Battery Indicator
Check the DC IN/Battery indicator to determine the status of the battery
pack- the following indicator conditions should be noted:
If the battery becomes too hot while it is being charged, the charge will
stop and the DC IN/Battery indicator will go out. When the battery’s
temperature falls to a normal range, charge will resume. This event occurs
regardless of whether the power to the computer is on or off.
Power Indicator
Check the Power indicator to determine the power status of the computer -
the following indicator conditions should be noted:
Blinking green Indicates the power was turned off while the
computer was in Sleep Mode.
Battery Types
The computer has two different types of batteries:
■ Battery — 3 cell or 6 cell (depending on the models)
■ Real Time Clock (RTC) battery
Battery
When the AC power cord is not connected, the computer’s main power
source is a removable lithium ion battery pack, also referred to in this
manual as the battery. You can purchase additional battery packs for
extended use of the computer away from an AC power source.
The battery pack is a lithium ion battery, which can explode if not properly
replaced, used, handled or disposed of. Dispose of the battery as required
by local ordinances or regulations. Use only batteries recommended by
TOSHIBA as replacements.
The battery maintains the state of the computer when you enable Resume.
When the computer is powered off in Hibernation and Sleep Mode, and the
AC adaptor is not connected, the battery pack supply power to maintain
data and programs in memory. If the battery pack is completely
discharged, hibernation and sleep do not function and the computer loses
all data in memory. One of the following messages appears when you turn
on the power:
The firmware has detected that a CMOS battery fail
occurred.<F1> continue
To ensure that the battery pack maintains its maximum capacity, operate
the computer on battery power at least once a month until the battery pack
is fully discharged. Refer to Extending Battery Life in this chapter for
procedures. If the computer is continuously operated on AC power, more
than a month, the battery may fail to retain a charge. It may not function
efficiently over the expected life of the battery and the Battery LED may not
indicate a low-battery condition.
Safety Precautions
Mishandling of batteries can cause death, serious injury or property
damage. Carefully observe the following advisories:
Danger: Indicates an imminently hazardous situation, Which could result in
death or serious injury, if you do not follow instructions.
Warning: Indicates a potentially hazardous situation, Which could result in
death or serious injury, if you do not follow instructions.
Caution: Indicates a potentially hazardous situation, Which if not avoided,
may result in moderate or minor injury or property damage.
Note: Provides important information.
Danger
1. Never try to dispose of the battery pack by burning or expose it to a
heating device such as a microwave oven. The battery pack could
explode and cause bodily injury.
2. Never try to disassemble, repair or otherwise tamper with a battery
pack. The battery pack will overheat and ignite. Leakage of caustic
alkaline solution or other electrolytic substances will cause fire or
injury, possibly resulting in death or serious injury.
3. Never short-circuit the battery pack by contacting the terminals with a
metal object. A short-circuit can cause fire or otherwise damage the
battery pack and possibly cause injury. To avoid accidental short-cir-
cuit, always wrap the battery pack in plastic and cover the terminals
with electrical tape when storing or disposing of the battery pack.
4. Never puncture the battery pack with a nail or other sharp object.
Never strike it with a hammer or other object. Never step on it.
5. Never try to change the battery pack in any manner other than that
described in user’s manual. Never connect the battery pack to a plug
socked or to a automobile’s cigarette lighter socket. It may rupture or
ignite.
6. Use only the battery pack supplied with the computer or other device
or an battery pack approved by the computer or device’s manufac-
turer. Battery packs have different voltages and terminal polarities.
Use of an improper battery could cause smoke, fire or rupture of the
battery pack.
7. Never subject a battery pack to heat, such as storage near a heat
source. Exposure to heat can cause the battery pack to ignite,
explode or leak caustic liquid and cause death or serious injury. It
could also fail or malfunction causing data lose.
8. Never expose the battery pack to abnormal shock, vibration or pres-
sure. The battery pack’s internal protective device will fail, causing it
to overheat, explode, ignite or leak caustic liquids possibly resulting in
death or serious injury.
9. Never let a battery pack become wet. A wet battery pack will over-
heat, ignite or rupture possibly resulting in death or serious injury.
Warning
1. Never allow caustic electrolyte fluid leaked from a battery pack to con-
tact your eyes, skin or clothing. If caustic electrolyte fluid should con-
tact your eyes, immediately wash your eyes with large amounts of
running water and seek medical attention, to help prevent eye dam-
age. It electrolyte fluid should contact your skin immediately wash it
under running water to prevent rash. If it contacts your clothes,
promptly remove them to prevent the fluid from contacting your skin or
eyes.
Caution
1. Never continue to use a battery pack after its recharging capacity has
become impaired, or after the display of a warning message indicating
that the battery pack’s power is exhausted. Continued use of an
exhausted or impaired battery pack could cause the loss of data.
2. Never dispose of battery packs with normal trash. Bring them to your
TOSHIBA dealer or to another recycling center to save resources and
prevent environmental damage. Cover the terminals with electrical
tape to prevent short-circuits, which could cause the battery pack to
ignite or rupture.
3. Use only battery packs recommended by TOSHIBA as replacements.
4. Always make sure the battery pack is installed correctly and securely.
Otherwise, a battery pack could fall out and possibly cause injury.
5. Change the battery pack only in an ambient temperature between 5
and 35 degrees Celsius. Otherwise, the electrolyte solution might
leak, battery pack performance might deteriorate and the battery life
might be shortened.
6. Be sure to monitor the remaining battery power. If the battery pack
and real time clock battery discharge completely. Sleep and hiberna-
tion will not function and data in memory will be lose. Also, the com-
puter might register an incorrect time and date. In this case, connect
the AC adaptor to recharge the batteries.
7. Never install or remove the battery pack without first turning off the
power and disconnecting the AC adaptor. Never remove the battery
pack while the computer in Hibernate or Sleep Mode. Data will be lost.
Note
1. Never remove the battery pack while the Wake-up on LAN function is
enabled. Data will be lost. Before you remove a battery pack, disable
the Wake-up on LAN function.
2. To ensure the battery pack maintains maximum capacity, operate the
computer on battery power once a week until the battery pack is fully
discharged. Refer to the section Extending Battery Life in this chapter
Procedures
To recharge a battery pack while it is installed in the computer, connect the
AC adaptor to the DC IN socket and plug the other end into a working
outlet.
The DC IN/Battery indicator glows amber when the battery is being
charged.
Use only the computer connected to an AC power source or the optional
TOSHIBA Batteries charger to charge the battery pack. Never attempt to
charge the battery pack with any other charger.
Time
The following table shows the approximate time required to fully charge a
discharged battery.
Charging time (hours)
Battery type Power on Power off
6. Slide the battery release latch to free the battery pack for removal, then
pull out the battery pack.
1. Be sure the computer’s power is off and all cables are disconnected.
2. Insert the battery pack.
1.BATTERY PACK
At this point, the hot keys FN + F1 to F9 do not work. They will function
after you enter the password.
If you enter the password incorrectly three times in a row, the computer
shuts off. In this case, you must turn the computer back on to retry
password entry.
Power-up Modes
The computer has the following power-up modes:
■ Boot: Computer shuts down without saving data. Always save your
work before you turn the computer off in boot mode.
■ Hibernation: Data in memory is saved to the hard disk.
■ Sleep: Data is maintained in the computer’s main memory.
Refer also to the sections Turning On The Power and Turning Off The
Power in Chapter 1.
Windows Utilities
You can specify the setting in Power Options.
Hot Keys
You can use hot keys FN + F3 to enter Sleep Mode and FN + F4 to enter
Hibernation Mode. See Chapter 5, The Keyboard for details.
Accessing HW Setup
To run the HW Setup program, click Start → All Programs → TOSHIBA →
Utilities → HWSetup.
HW Setup Window
The HW Setup window contains a number of tabs (General, Password,
Display, Boot Priority, Keyboard, LAN and USB) to allow specific functions
of the computer to be configured. In addition there are also three buttons :
OK, Cancel and Apply.
OK Accepts your changes and closes the HW Setup
window.
General
This window displays the BIOS/EC version and contains two buttons:
Default and About.
Setup
This field displays the installed BIOS version, date and EC version.
Password
User Password
Lets you register a new password or change/remove an existing password.
Owner String
This blank field is used to display a message when the password field is
displayed on startup. If a password is not registered the message will not
be shown. The maximum length is 256 characters.
Display
This tab allows you to customize your computer’s display settings for either
the internal LCD screen or for an external monitor.
Power On Display
This tab allows you to select the display to be used when the computer is
started. Please note that this setting is only available on standard VGA
mode and is not available as part of the Windows Desktop properties.
Boot Priority
Boot Priority Options
This tab allows you to set the priority for booting the computer. The Boot
Priority Options setting window will be displayed as shown below. Click the
up and down arrow buttons to adjust the priority.
You can override the settings and manually select a boot device by
pressing one of the following keys while the computer is booting:
U Selects the USB diskette drive*1.
*1 The floppy diskette drive will be used to start the computer when there is
a bootable disk contained in the external drive.
*2 The optical disc drive will be used to start the computer when there is a
bootable disk contained in the drive.
Keyboard
Wake-up on Keyboard
When this feature is enabled and the computer is in Sleep Mode, you can
turn on the computer by pressing any key. However, please be aware that
this option will only work with the internal keyboard and only when the
computer is in Sleep Mode.
USB
Legacy USB Support
You can use this option to enable or disable USB keyboard/mouse legacy
emulation so that, even if your operating system does not support USB
devices, you can still use a standard USB mouse and keyboard - to achieve
this you should set the appropriate option(s) to Enabled.
LAN
Wake-up on LAN
This feature lets the computer's power be turned on from shutdown when it
receives a wake-up packet ( Magic packet ) from the LAN.
■ The Wake-up on LAN function consumes power even when the system
is off. Leave the AC adaptor connected while using this feature.
■ Regarding Wake-up on LAN from sleep or hibernation, you must check
the “Allow the device to wake the computer” check box within the LAN
Device properties. ( This feafure does not effect the Wake-up on LAN
from sleep or hibernation. )
Built-in LAN
This feature enables or disables the Built-in LAN.
Enabled Enables built-in LAN functions. (Default)
Troubleshooting
Preliminary Checklist
Consider the simplest solution first. The items in this checklist are easy to
fix and yet can cause what appears to be a serious problem.
■ Make sure you turn on all peripheral devices before you turn on the
computer. This includes your printer and any other external device you
are using.
■ Before you attach an external device, turn the computer off. When you
turn the computer back on it recognizes the new device.
■ Make sure all options are set properly in the setup program.
■ Check all cables. Are they correctly and firmly attached? Loose cables
can cause signal errors.
■ Inspect all connecting cables for loose wires and all connectors for
loose pins.
■ Check that your diskette is correctly inserted and that the diskette’s
write protect tab is correctly set.
Make notes of your observations and keep them in a permanent error log.
This will help you describe your problems to your dealer. If a problem
recurs, the log will help you identify the problem faster.
System Start-up
When the computer does not start properly, check the following items:
■ Self Test
■ Power Sources
■ Power-on Password
Self Test
When the computer starts up, the self-test will be run automatically, and the
following will be displayed:
TOSHIBA Leading Innovation>>>
This message remains on the screen for a few seconds.
If the self test is successful, the computer tries to load the operating
system.
Depending on how the Boot Priority is set in the Hardware Setup, the
computer tries to load first from drive A then from drive C, or first from drive
C then from drive A.
If any of the following conditions are present, the self test failed:
■ The computer stops and does not proceed to display information or
messages.
■ Random characters appear on the screen, and the system does not
function normally.
■ The screen displays an error message.
Turn off the computer and check all cable connections. If the test fails
again, contact your dealer.
Power
When the computer is not plugged into an AC adaptor, the battery pack is
the primary power source. However, your computer has a number of other
power resources, including intelligent power supply and Real Time Clock
battery. These resources are interrelated and any one could affect apparent
power problems.
This section provides check lists for AC adaptor and the main battery. If you
cannot resolve a problem after following them, the cause could lie with
another power resource. In such case, contact your dealer.
AC Power
If you have trouble turning on the computer with the AC adaptor connected,
check the DC IN/Battery indicator. Refer to Chapter 6, Power and Power-
up Modes for more information.
Problem Procedure
Battery
If you suspect a problem with the battery, check the DC IN/Battery
indicator. For information on indicators and battery operation see Chapter
6, Power and Power-up Modes.
Problem Procedure
Problem Procedure
Password
Problem Procedure
Keyboard
Keyboard problems can be caused by your setup configuration. For more
information refer to Chapter 5, The Keyboard and Chapter 7, HW Setup
and Passwords.
Problem Procedure
Output to screen is Make sure the software you are using is not
garbled remapping the keyboard. Remapping involves
reassigning the meaning of each key. See your
software’s documentation.
LCD Panel
Apparent LCD problems may be related to the computer’s setup. Refer to
Chapter 7, HW Setup and Passwords, for more information.
Problem Procedure
Markings appear on the They might have come from contact with the
LCD screen. keyboard or touchpad. Try wiping the LCD gently
with a clean dry cloth. If markings remain, use
LCD cleaner. Be sure to let the LCD dry before
closing it.
Problem Procedure
Problem Procedure
You cannot access a Make sure the drive’s drawer is securely closed.
CD/DVD in the drive Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the drawer could block laser
light from reading the CD or DVD. Make sure
there is no obstruction. Remove any foreign
object.
Check whether the DVD is dirty. If it is, wipe it
with a cleaning cloth dipped in water or a neutral
cleaner. See the Media Care section in Chapter 4
for details on cleaning.
Some CD/DVDs run The software or hardware configuration may be
correctly, but others do causing a problem. Make sure the hardware
not configuration matches your software’s needs.
Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. Refer
to Chapter 3,Hardware, Utilities and Options for
more information.
Check the region code on the DVD. It must
match that on the drive. Region codes are listed
in the Optical Disc Drive section in Chapter 2,
The Grand Tour.
Cannot write correctly If you have trouble writing, make sure you are
observing the following precautions:
■ Use only media recommended by TOSHIBA
■ Do not use the mouse or keyboard during writing.
■ Use only the software supplied with the computer
for recording.
■ Do not run or start other software during writing.
■ Do not jar the computer during writing.
■ Do not connect/disconnect external devices or
install/remove internal cards during writing.
Diskette Drive
Problem Procedure
Drive does not operate There may be a faulty cable connection. Check
the connection to the computer and to the drive.
You cannot access the Try another diskette. If you can access the
external diskette drive diskette, the original diskette (not the drive) is
probably causing the problem.
Pointing Device
If you are using a USB mouse, also refer to the USB section in this chapter
and to your mouse documentation.
Touchpad
Problem Procedure
Problem Procedure
The mouse pointer Try changing the speed setting in the mouse
moves too fast or too control utility. Click Start → Control Panel →
slow Hardware and Sound → Mouse to access it.
USB Mouse
This section applies only with Windows 7 operating system.
Problem Procedure
Problem Procedure
The mouse pointer The mouse might be dirty. Refer to your mouse
moves erratically documentations for instructions on cleaning.
Problem Procedure
Memory card error Reseat the memory card to make sure it is firmly
occurs connected.
You cannot write to the Make sure the card is not write protected.
memory card
You cannot read a file Make sure the target file is on the memory card
inserted in the slot.
External Monitor
Refer also to Chapter 3, Hardware, Utilities and Options, and to your
monitor’s documentation.
Problem Procedure
Monitor does not turn Make sure that the external monitor’s power
on switch is on. Confirm that the external monitor’s
power cable is plugged into a working power
outlet.
Problem Procedure
Display error occurs Check that the cable connecting the external
monitor to the computer is attached firmly.
Sound System
Problem Procedure
No sound is heard Adjust the volume by pressing FN + 3 to
decrease or FN + 4 to increase.
Check the software volume settings.
Make sure the headphone connection is secure.
Check Windows Device Manager. Make sure the
sound function is enabled and that settings for I/O
address, Interrupt level and DMA are correct for
your software and do not conflict with other
hardware devices that you may have connected
to the computer.
USB
Refer also to your USB device’s documentation.
Problem Procedure
USB device does not Check for a firm cable connection between the
work USB ports on the computer and the USB device.
Make sure the USB device drivers are properly
installed. Refer to your Windows documentation
for information on checking the drivers.
If you are using an operating system that does
not support USB, you can still use a USB mouse
and/or USB keyboard. If these devices do not
work, make sure the USB KB/Mouse Legacy
Emulation item in HW Setup is set to [Enable].
Sleep/Hibernation
Problem Procedure
The system will not Is Windows Media Player open? The system
enter sleep/hibernation might not enter sleep/hibernation, if Windows
Media Player is either playing a selection or
finished playing a selection. Close Windows
Media Player before you select
sleep/hibernation.
LAN
Problem Procedure
Cannot access LAN Check for a firm cable connection between the
LAN jack and the LAN HUB.
Wireless LAN
If the following procedures do not restore LAN access, consult your LAN
administrator. For more information on wireless communication, refer to
Chapter 4, Operating Basics.
Problem Procedure
Recovery Media
Problem Procedure
The following message You will see this message if you have previously
appears when chosen to remove the partition and are trying to
executing Recovery create Recovery Media. When there is no
Media Creator. recovery partition, the Recovery Media Creator
[The Recovery cannot make Recovery Media.
Media Creator can
not be launched However, if you have already created a
because there is “Recovery Media”, you can use it to restore the
no recovery recovery partition.
partition.] Simply follow the instructions in “Restoring the
preinstall software from your creating Recovery
Media” section in this manual. You will be
directed to select Restore Original Factory Image
from the drop-down menu. If you have not
created Recovery Media, please contact
TOSHIBA support for assistance.
TOSHIBA Support
If you require any additional help using your computer or if you are having
problems operating the computer, you may need to contact TOSHIBA for
additional technical assistance.
Where to Write
If you are still unable to solve the problem and suspect that it is hardware
related, write to TOSHIBA at the nearest location listed on the below.
Singapore Spain
TOSHIBA Singapore Pte. Ltd. TOSHIBA Information Systems,
438B Alexandra Road #06-01 ESPAÑA
Alexandra Technopark Parque Empresarial San Fernando
Singapore 119968 Edificio Europa, 1a Planta, Escalera A
28830, Madrid, España
United States of America United Kingdom
TOSHIBA America Information TOSHIBA Information Systems (U.K.)
Systems, Inc. Ltd.
9740 Irvine Boulevard TOSHIBA Court
Irvine, California 92618 Weybridge Business Park
USA Addlestone Road
Weybridge, Surrey KT15 2UL
India The Rest of Europe
TOSHIBA India Pvt Ltd. TOSHIBA Europe (I.E.) GmbH
PC Division Geschäftsbereich,
6th Floor, DR Gopal Das Bhawan Deutschland-Österreich
Barakhamba Road, Hammfelddamm 8,
Delhi-110001, India D-41460 Neuss, Germany
Specifications
Environmental Requirements
Operating Non-operating
Ambient temperature 5°C to 35°C -20°C to 60°C
Relative humidity 20% to 80% 10% to 90%
Altitude (from sea level) 0 to 3,000 meters 0 to 10,000 meters
Power Requirements
Computer 19V DC
Display Controller
The display controller interprets software commands into hardware com-
mands that turn particular pixels on or off.
Due to the display panel's increased resolution, lines may appear broken in
when displaying images in full-screen text mode.
The display controller also controls the video mode and uses industry
standard rules to govern the screen resolution and the maximum number of
colors that can be displayed at any one time. Therefore, software written for
a given video mode will run on any computer that supports that mode.
Video mode
Video mode settings are configured via the Screen Resolution dialog.To
open the Screen Resolution dialog, click Start → Control Panel →
Appearance and Personalization → Display → Change display
settings.
If you are running some application ( for example a 3D application or video
playback and so on), you may use some disturbance, flickering or frame
dropping on your screen.
If that occurs,adjust the resolution of display, lowering it until the screen is
displayed properly.
Disabling Windows AeroTM may also help correct this issue.
Wireless LAN
This appendix is intended to help you get your Wireless LAN network up
and running, with a minimum of parameters.
Card Specifications
Radio Characteristics
Radio characteristics of Wireless LAN cards may vary according to:
■ Country/region where the product was purchased
■ Type of product
Wireless communication is often subject to local radio regulations.
Although Wireless LAN wireless networking products have been designed
for operation in the license-free 2.4 GHz and 5 GHz band, local radio
regulations may impose a number of limitations to the use of wireless
communication equipment.
Radio ■ Band 5 GHz (5150-5850 MHz) (Revision A, N)
Frequency ■ Band 2.4 GHz (2400-2483.5 MHz)
(Revision B, G, N)
The range of the wireless signal is related to the transmit rate of the wire-
less communication. Communications at lower transmit range may travel
larger distances.
■ The range of your wireless devices can be affected when the antennas
are placed near metal surfaces and solid high-density materials.
■ Range is also impacted due to “obstacles” in the signal path of the radio
that may either absorb or reflect the radio signal.
2.4 GHz Band Channels Sets (Wireless IEEE 802.11 Revision B, G and
N)
1 2412
2 2417
3 2422
4 2427
5 2432
6 2437
7 2442
8 2447
9 2452
10 2457*1
11 2462
12 2467*2
13 2472*2
*1 Factory-set default channels
*2 The band width and the channel which can be used depends on the
installed wireless LAN module. And the approved channels on using are
different at each country or region. The channel configuration is managed
as follows:
■ For wireless clients that operate in a Wireless LAN Infrastructure, the
Wireless LAN module will automatically start operation at the channel
identified by the Wireless LAN Access Point. When roaming between
different access points the station can dynamically switch to another
channel if required.
■ For Wireless LAN modules installed in wireless clients that operating in
a peer-to-peer mode, the module will use the default channel 10.
■ In a Wireless LAN Access Point, the Wireless LAN module will use the
factory-set default channel (printed in bold), unless the LAN
Administrator selected a different channel when configuring the
Wireless LAN Access Point device.
161 5805*2
165 5825*2
*1 Factory-set default channels
*2 The channel which can be used depends on the installed wireless LAN
module. And the approved channels on using are different at each country
or region. The channel configuration is managed as follows:
■ For wireless clients that operate in a Wireless LAN Infrastructure, the
Wireless LAN module will automatically start operation at the channel
identified by the Wireless LAN Access Point. When roaming between
different access points the station can dynamically switch to another
channel if required.
■ In a Wireless LAN Access Point, the Wireless LAN module will use the
factory-set default channel (printed in bold), unless the LAN
Administrator selected a different channel when configuring the
Wireless LAN Access Point device.
The AC input plug of power cord must be compatible with various interna-
tional AC power outlets. Power cords need to meet the local standards and
the specifications listed as below:
Length: Minimum 1.7 meters
Wire size: Minimum 0.75 mm2
Current rating: Minimum 2.5 amperes
Voltage rating: 125 or 250V AC
(depending on country/region’s power standards)
Certification agencies
Europe:
Austria: OVE Italy: IMQ
Belgium: CEBEC The Netherlands: KEMA
Denmark: DEMKO Norway: NEMKO
Finland: FIMKO Sweden: SEMKO
France: LCIE Switzerland: SEV
Germany: VDE United Kingdom: BSI
Outside of Europe:
U.S. and Canada: UL listed and CSA certified
No. 18 AWG, Type SVT or SPT-2
China: CCC, CQC India: STQC
Australia: AS
The following illustrations show the plug shapes for USA, Australia, Can-
ada, United Kingdom, Europe, and China.
USA United Kingdom
UL approved BS approved
Australia Europe
Canada China
Legal Footnotes
CPU*1
Central Processing Unit (CPU) Performance Disclaimer.
CPU performance in your computer product may vary from specifications
under the following conditions:
■ use of certain external peripheral products
■ use of battery power instead of AC power
■ use of certain multimedia, computer generated graphics or video
applications
■ use of standard telephone lines or low speed network connections
■ use of complex modeling software, such as high end computer aided
design applications
■ use of several applications or functionalities simultaneously
■ use of computer in areas with low air pressure (high altitude > 1,000
meters or > 3,280 feet above sea level)
■ use of computer at temperatures outside the range of 5°C to 30°C (41°F
to 86°F) or > 25°C (77°F) at high altitude (all temperature references
are approximate and may vary depending on the specific computer
model-please refer to your PC documentation or visit the TOSHIBA
website at http://www.pcsupport.toshiba.com for details)
CPU performance may also vary from specifications due to design
configuration.
64-Bit Computing
64-bit processors are designed to take advantage of 32 and 64 bit
computing.
64-bit computing requires that the following hardware and software
requirements are met:
■ 64-bit Operating System
■ 64-bit CPU, Chipset and BIOS (Basic Input/Output System)
■ 64-bit Device drivers
■ 64-bit applications
Certain device drivers and/or applications may not be compatible with a 64-
bit CPU and therefore may not function properly.
Battery Life*3
Battery life may vary considerably depending on product model,
configuration, applications, power management settings and features
utilized, as well as the natural performance variations produced by the
design of individual components. Published battery life numbers are
achieved on select models and configurations tested by TOSHIBA at the
time of publication. Recharge time varies depending on usage. Battery may
not charge while computer is consuming full power.
After a period of time, the battery will lose its ability to perform at maximum
capacity and will need to be replaced. This is normal for all batteries. To
purchase a new battery pack, see the accessories information that shipped
with your computer or visit the TOSHIBA web site at
http://www.pcsupport.toshiba.com.
LCD*5
Over a period of time, and depending on the usage of the computer, the
brightness of the LCD screen will deteriorate. This is an intrinsic
characteristic of LCD technology.
Maximum brightness is only available when operating in AC power mode.
Screen will dim when the computer is operated on battery power and you
will not be able to increase the brightness of the screen.
Wireless LAN*7
The transmission speed over the Wireless LAN and the distance over
which Wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, and client design and software/hardware configurations. The
actual transmission speed will be lower than the theoretical maximum
speed.
Non-applicable Icons
Certain notebook chassis are designed to accommodate all possible
configurations for an entire product series. Your selected model may not
have all the features and specifications corresponding to all of the icons or
switches shown on the notebook chassis, unless you have selected all
those features.
Copy Protection
Copy protection technology included in certain media may prevent or limit
recording or viewing of the media.
The terms in this glossary cover topics related to this manual. Alternate
naming is included for reference.
Abbreviations
AC: alternating current
ACPI: Advanced Configuration and Power Interface
AGP: accelerated graphics port
AMT: Intel Active Management Technology
ANSI: American National Standards Institute
APM: advanced power manager
ASCII: American Standard Code for Information Interchange
BIOS: basic input output system
bps: bits per second
CD: compact disc
CD-ROM: Compact Disc Read Only Memory
CD-RW: Compact Disc ReWritable
CMOS: complementary metal-oxide semiconductor
CPU: central processing unit
CRT: cathode ray tube
DC: direct current
DDC: display data channel
DIMM: dual inline memory module
DMA: direct memory access
DOS: disk operating system
DVD: digital versatile disc
DVD-R: Digital Versatile Disc Recordable
DVD-RAM: Digital Versatile Disc Random Access Memory
DVD-R DL: Digital Versatile Disc Recordable Dual Layer
DVD-ROM: Digital Versatile Disc Read Only Memory
DVD-RW: Digital Versatile Disc ReWritable
DVD+R DL: Digital Versatile Disc Recordable Double Layer
A
adaptor: A device that provides an interface between two dissimilar
electronic devices. For example, the AC adaptor modifies the power
from a wall outlet for use by the computer. This term also refers to
the add-in circuit cards that control external devices, such as video
monitors and magnetic tape devices.
allocate: To assign a space or function for a specific task.
alphanumeric: Keyboard characters including letters, numbers and other
symbols, such as punctuation marks or mathematical symbols.
alternating current (AC): Electric current that reverses its direction of flow
at regular intervals.
analog signal: A signal whose characteristics such as amplitude and
frequency vary in proportion to (are an analog of) the value to be
transmitted. Voice communications are analog signals.
ANSI: American National Standards Institute. An organization established
to adopt and define standards for a variety of technical disciplines.
For example, ANSI defined the ASCII standard and other
information processing requirements.
antistatic: A material used to prevent the buildup of static electricity.
application: A group of programs that together are used for a specific task
such as accounting, financial planning, spreadsheets, word
processing and games.
ASCII: American Standard Code for Information Interchange. ASCII code is
a set of 256 binary codes that represent the most commonly used
letters, numbers, and symbols.
async: Short for asynchronous.
asynchronous: Lacking regular time relationship. As applied to computer
communications, asynchronous refers to the method of transmitting
data that does not require a steady stream of bits to be transmitted
at regular time intervals.
B
backup: A duplicate copy of files kept as a spare in case the original is
destroyed.
batch file: A file that can be executed from the system prompt containing a
sequence of operating system commands or executable files.
binary: The base two number system composed of zeros and ones (off or
on), used by most digital computers. The right-most digit of a binary
number has a value of 1, the next a value of 2, then 4, 8, 16, and so
on. For example, the binary number 101 has a value of 5. See also
ASCII.
BIOS: Basic Input Output System. The firmware that controls data flow
within the computer. See also firmware.
bit: Derived from “binary digit,” the basic unit of information used by the
computer. It is either zero or one. Eight bits is one byte. See also
byte.
board: A circuit board. An internal card containing electronic components,
called chips, which perform a specific function or increase the
capabilities of the system.
boot: Short for bootstrap. A program that starts or restarts the computer.
The program reads instructions from a storage device into the
computer’s memory.
bps: Bits per second. Typically used to describe the data transmission
speed of a modem.
buffer: The portion of the computer’s memory where data is temporarily
stored. Buffers often compensate for differences in the rate of flow
from one device to another.
bus: An interface for transmission of signals, data or electric power.
byte: The representation of a single character. A sequence of eight bits
treated as a single unit; also the smallest addressable unit within the
system.
C
cache memory: High speed memory which stores data that increases
processor speed and data transfer rate. When the CPU reads data
from main memory, it stores a copy of this data in cache memory.
The next time the CPU needs that same data, it looks for it in the
cache memory rather than the main memory, which saves time. The
computer has two cache levels. Level one is incorporated into the
processor and level two resides in external memory.
capacity: The amount of data that can be stored on a magnetic storage
device such as a floppy diskette or hard disk drive. It is usually
described in terms of kilobytes (KB), where one KB = 1024 bytes
and megabytes (MB), where one MB = 1024 KB.
card: Synonym for board. See board.
CardBus: An industry standard bus for 32-bit PC Cards.
CD-ROM: A Compact Disc Read Only Memory is a high capacity disc that
can be read from but not written to. The CD-ROM drive uses a laser,
rather than magnetic heads, to read data from the disc.
CD-R: A Compact Disc Recordable disc can be written once and read
many times. See also CD-ROM.
CD-RW: A Compact Disc ReWritable disc can be rewritten many times.
See also CD-ROM.
D
data: Information that is factual, measurable or statistical that a computer
can process, store, or retrieve.
data bits: A data communications parameter controlling the number of bits
(binary digits) used to make up a byte. If data bits = 7 the computer
can generate 128 unique characters. If data bits = 8 the computer
can generate 256 unique characters.
DC: Direct Current. Electric current that flows in one direction. This type of
power is usually supplied by batteries.
default: The parameter value automatically selected by the system when
you or the program do not provide instructions. Also called a preset
value.
delete: To remove data from a disk or other data storage device.
Synonymous with erase.
device driver: A program that controls communication between a specific
peripheral device and the computer. The CONFIG.SYS file contains
device drivers that MS-DOS loads when you turn the computer on.
dialog box: A window that accepts user input to make system settings or
record other information.
Digital Audio: An audio compression standard that enables high-quality
transmission and real-time playback of sound files.
disk drive: The device that randomly accesses information on a disk and
copies it to the computer’s memory. It also writes data from memory
to the disk. To accomplish these tasks, the unit physically rotates the
disk at high speed past a read-write head.
disk storage: Storing data on magnetic disk. Data is arranged on
concentric tracks much like a phonograph record.
display: A CRT, LCD, or other image producing device used to view
computer output.
documentation: The set of manuals and/or other instructions written for
the users of a computer system or application. Computer system
documentation typically includes procedural and tutorial information
as well as system functions.
DOS: Disk Operating System. See operating system.
driver: A software program, generally part of the operating system, that
controls a specific piece of hardware (frequently a peripheral device
such as a printer or mouse).
DVB-T (Digital Video Broadcasting - Terrestrial): Also known as
terrestrial digital TV. Digital TV broadcasting standard.
DVD-R (+R, -R): A Digital Versatile Disc Recordable disk can be written
once and read many times. The DVD-R drive uses a laser to read
data from the disc.
DVD-RAM: A Digital Versatile Disc Random Access Memory is a high-
capacity, high performance disc that allows you to store large
volumes of data. The DVD-RAM drive uses a laser to read data from
the disc.
DVD-R DL: A disc having two layers on one side with the DVD-R storage
capacity about 1.8 times larger than before. The DVD-RW drive
uses a laser to read data from the disc.
DVD-ROM: A Digital Versatile Disc Read Only Memory is a high capacity,
high performance disc suitable for play back of video and other
high-density files. The DVD-ROM drive uses a laser to read data
from the disc.
DVD-RW (+RW, -RW): A Digital Versatile Disc ReWritable disc can be
rewritten many times.
DVD+R DL: A disc having two layers on one side with the DVD+R storage
capacity about 1.8 times larger than before. The DVD-RW drive
uses a laser to read data from the disc.
E
echo: To send back a reflection of the transmitted data to the sending
device. You can display the information on the screen, or output it to
the printer, or both. When a computer receives back data it
transmitted to a CRT (or other peripheral device) and then
retransmits the data to printer, the printer is said to echo the CRT.
erase: See delete.
escape: 1) A code (ASCII code 27), signaling the computer that what
follows are commands; used with peripheral devices such as
printers and modems.
2) A means of aborting the task currently in progress.
escape guard time: A time before and after an escape code is sent to the
modem which distinguishes between escapes that are part of the
transmitted data, and escapes that are intended as a command to
the modem.
execute: To interpret and execute an instruction.
Extended Capability Port: An industry standard that provides a data
buffer, switchable forward and reverse data transmission, and run
length encoding (RLE) support.
F
fast infrared: An industry standard that enables cableless infrared serial
data transfer at speeds of up to 4 Mbps.
file: A collection of related information; a file can contain data, programs, or
both.
firmware: A set of instructions built into the hardware which controls and
directs a microprocessor’s activities.
floppy diskette: A removable disk that stores magnetically encoded data.
floppy diskette drive (FDD): An electromechanical device that reads and
writes to floppy diskettes.
Fn-esse: A TOSHIBA utility that allows you to assign functions to hot keys.
folder: An icon in Windows used to store documents or other folders.
format: The process of readying a blank disk for its first use. Formatting
establishes the structure of the disk that the operating system
expects before it writes files or programs onto the disk.
function keys: The keys labeled F1 through F12 that tell the computer to
perform certain functions.
G
gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also
megabyte.
graphics: Drawings, pictures, or other images, such as charts or graphs, to
present information.
H
hard disk: A non-removable disk usually referred to as drive C. The factory
installs this disk and only a trained engineer can remove it for
servicing. Also called fixed disk.
hard disk drive (HDD): An electromechanical device that reads and writes
a hard disk. See also hard disk.
hardware: The physical electronic and mechanical components of a
computer system: typically, the computer itself, external disk drives,
etc. See also software and firmware.
hertz: A unit of wave frequency that equals one cycle per second.
hexadecimal: The base 16 numbering system composed of the digits 0
through 9 and the letters A, B, C, D, E, and F.
host computer: The computer that controls, regulates, and transmits
information to a device or another computer.
hot key: The computer’s feature in which certain keys in combination with
the extended function key, FN, can be used to set system
parameters, such as speaker volume.
HW Setup: A TOSHIBA utility that allows you to set the parameters for
various hardware components.
I
icon: A small graphic image displayed on the screen or in the indicator
panel. In Windows, an icon represents an object that the user can
manipulate.
i.LINK (IEEE1394): This port enables high-speed data transfer directly
from external devices such as digital video cameras.
J
jumper: A small clip or wire that allows you to change the hardware
characteristics by electrically connecting two points of a circuit.
K
K: Taken from the Greek word kilo, meaning 1000; often used as equivalent
to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
KB: See kilobyte.
keyboard: An input device containing switches that are activated by
manually pressing marked keys. Each keystroke activates a switch
that transmits a specific code to the computer. For each key, the
transmitted code is, in turn, representative of the (ASCII) character
marked on the key.
kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte
and megabyte.
L
level 2 cache: See cache.
Light Emitting Diode (LED): A semiconductor device that emits light when
a current is applied.
Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of
glass coated with transparent conducting material. The viewing-side
coating is etched into character forming segments with leads that
extend to the edge of the glass. Applying a voltage between the
glass sheets alters the brightness of the liquid crystal.
LSI: Large Scale Integration.
1) A technology that allows the inclusion of up to 100,000 simple
logic gates on a single chip.
2) An integrated circuit that uses large scale integration.
M
main board: See motherboard.
megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also
kilobyte.
megahertz: A unit of wave frequency that equals 1 million cycles per
second. See also hertz.
menu: A software interface that displays a list of options on the screen.
Also called a screen.
microprocessor: A hardware component contained in a single integrated
circuit that carries out instructions. Also called the central
processing unit (CPU), one of the main parts of the computer.
mode: A method of operation, for example, the Boot Mode, Sleep Mode or
the Hibernation Mode.
modem: Derived from modulator/demodulator, a device that converts
(modulates) digital data for transmission over telephone lines and
then converts modulated data (demodulates) to digital format where
received.
monitor: A device that uses rows and columns of pixels to display
alphanumeric characters or graphic images. See also CRT.
motherboard: A name sometimes used to refer to the main printed circuit
board in processing equipment. It usually contains integrated
circuits that perform the processor’s basic functions and provides
connectors for adding other boards that perform special functions.
Sometimes called a main board.
N
non-system disk: A formatted floppy diskette you can use to store
programs and data but you cannot use to start the computer. See
system disk.
nonvolatile memory: Memory, usually read-only (ROM), that is capable of
permanently storing information. Turning the computer’s power off
does not alter data stored in nonvolatile memory.
numeric keypad overlay: A feature that allows you to use certain keys on
the keyboard to perform numeric entry, or to control cursor and page
movement.
O
OCR: Optical Character Recognition (reader). A technique or device that
uses laser or visible light to identify characters and input them into a
storage device.
online state: A functional state of a peripheral device when it is ready to
receive or transmit data.
operating system: A group of programs that controls the basic operation
of a computer. Operating system functions include interpreting
programs, creating data files, and controlling the transmission and
receipt (input/output) of data to and from memory and peripheral
devices.
output: The results of a computer operation. Output commonly indicates
data.
1) printed on paper, 2) displayed at a terminal, 3) sent through the
serial port of internal modem, or 4) stored on some magnetic media.
P
PAL: PAL (Phase Alternating Line) is the dominant video and broadcasting
standard in Europe.
parity: 1) The symmetrical relationship between two parameter values
(integers) both of which are either on or off; odd or even; 0 or 1.
2) In serial communications, an error detection bit that is added to a
group of data bits making the sum of the bits even or odd. Parity can
be set to none, odd, or even.
password: A unique string of characters used to identify a specific user.
The computer provides various levels of password protection such
as user and supervisor.
pel: The smallest area of the display that can be addressed by software.
Equal in size to a pixel or group of pixels. See pixel.
peripheral component interconnect: An industry standard 32-bit bus.
peripheral device: An I/O device that is external to the central processor
and/or main memory such as a printer or a mouse.
Péritel: Péritel is a 21-pin connecting cable/port system that allows images
and high-quality stereo sound (including Dolby® Pro-Logic sound
formats) to be sent from one audio-visual device to another. It is also
known as a “SCART connector” or “Euro connector”.
pixel: A picture element. The smallest dot that can be made on a display or
printer. Also called a pel.
plug and play: A capability with Windows that enables the system to
automatically recognize connections of external devices and make
the necessary configurations in the computer.
port: The electrical connection through which the computer sends and
receives data to and from devices or other computers.
Power Saver Utility: A TOSHIBA utility that allows you to set the
parameters for various power-saving functions.
R
Radio frequency interference (RFI) shield: A metal shield enclosing the
printed circuit boards of the printer or computer to prevent radio and
TV interference. All computer equipment generates radio frequency
signals. The FCC regulates the amount of signals a computing
device can allow past its shielding. A Class A device is sufficient for
office use. Class B provides a more stringent classification for home
equipment use. TOSHIBA portable computers comply with Class B
computing device regulations.
Random Access Memory (RAM): High speed memory within the
computer circuitry that can be read or written to.
restart: Resetting a computer without turning it off (also called “warm boot”
or “soft reset”). See also boot.
RGB: Red, green and blue. A device that uses three input signals, each
activating an electron gun for a primary additive color (red, green
and blue) or port for using such a device. See also CRT.
RJ11: A modular telephone jack.
RJ45: A modular LAN jack.
ROM: Read Only Memory: A nonvolatile memory chip manufactured to
contain information that controls the computer’s basic operation.
You cannot access or change information stored in ROM.
S
S-Video: Short for Super-Video, a type of connection used by S-VHS
videocassette players, camcorders, DVD players, etc. to transmit
high-quality video signals.
SCSI: Small Computer System Interface is an industry standard interface
for connection of a variety of peripheral devices.
SD Card: Secure Digital cards are flash memory widely used in a variety of
digital devices such as digital cameras and Personal Digital
Assistants.
SECAM L: SECAM (Sequential Color Memory) is a broadcasting standard
used in France.
serial communications: A communications technique that uses as few as
two interconnecting wires to send bits one after another.
serial interface: Refer to a type of information exchange that transmits
information sequentially, one bit at a time.
T
terminal: A typewriter-like keyboard and CRT display screen connected to
the computer for data input/output.
TFT display: A liquid crystal display (LCD) made from an array of liquid
crystal cells using active-matrix technology with thin film transistor
(TFT) to drive each cell.
touchpad: A pointing device integrated into the TOSHIBA computer palm
rest.
TTL: Transistor-transistor logic. A logic circuit design that uses switching
transistors for gates and storage.
U
Universal Serial Bus: This serial interface allows you to communicate with
several devices connected in a chain to a single port on the
computer.
V
VGA: Video Graphics Array is an industry standard video adaptor that
allows you to run any popular software.
volatile memory: Random access memory (RAM) that stores information
as long as power is supplied to the computer.
W
User’s Manual Glossary-13
Glossary
A D
AC adaptor, 2-4, 2-12, 3-5, A-1 DC IN, 2-4
additional, 3-12, 3-21 connecting, 1-5
connecting, 1-3 location, 2-4
problems, 8-5 DC IN/Battery
safety instructions, -ii indicator, 2-8
Display, 2-6, 2-7, 3-3, E-3
B automatic power off, 3-7
Battery brightness down, 5-3
charging, 6-7 brightness up, 5-3
life, E-2 controller, B-1
monitoring capacity, 6-8 HW Setup, 7-2
Real Time Clock battery, 3-5, opening, 1-6
6-4 problems, 8-7, 8-11
retention time, 6-9 resolution, 5-4
types, 6-3 switching, 5-3
Battery pack, 2-5, 3-5, 3-12, 6-3 DVD Super Multi (+-R DL) drive,
additional, 3-21 2-11, 3-3, 4-12
extending battery life, 6-10 problems, 8-8
indicator, 6-2
operating time, 6-9 E
problems, 8-5 External monitor, 3-21
replacing, 6-10 controller, B-1
safety instructions, -ii, 6-4 HW Setup, 7-2
save mode, 3-7 port, 2-2, 3-5
Bridge media slot problems, 8-11
function, 3-13
problems, 8-11 F
Fan vent
C location, 2-2
Checklist FN + 1 (TOSHIBA zooming utility
equipment, 1-1 reduce), 5-4
problems, 8-2, 8-3 FN + 2 (TOSHIBA zooming utility
Cleaning the computer, 4-28 enlarge), 5-4
FN + 3 (Volume Down), 5-4
FN + 4 (Volume Up), 5-4
H K
Hard disk drive Keyboard, 3-4, 5-1
automatic power off, 3-7 FN sticky key, 5-5
capacity, E-3 function keys, 5-2
problems, 8-7 hot keys, 5-2
Headphone, 3-5 HW Setup, 7-4
problems, 8-12 indicator, 2-9
Hibernation mode, 3-8 problems, 8-6
problems, 8-13 typewriter keys, 5-1
setting, 1-10 Windows special keys, 5-5
Hot keys, 3-7
BREAK, 5-5
L
brightness down, 5-3 LAN, 3-6, 4-26
brightness up, 5-3 cable types, 4-27
hibernate, 5-3 connecting, 4-27
lock, 5-2 disconnecting, 4-28
output/display, 5-3 port, 2-2
PAUSE, 5-5 problems, 8-13
power plan, 5-2 LCD, See Display
PRTSC, 5-4 Legal Footnotes, E-1
sleep, 5-3 Lock, security, See Security lock
sound mute, 5-2
SYSRQ, 5-4
M
TOSHIBA zooming utility Memory, 3-1, E-2
enlarge, 5-4 expansion, 3-12, 3-17
TOSHIBA zooming utility installing module, 3-17
reduce, 5-4 module cover, 2-5
Volume Down, 5-4 removing module, 3-20
Volume Up, 5-4
Wireless, 5-3
T
TOSHIBA Accessibility, 3-9
TOSHIBA Assist, 3-10
TOSHIBA Bulletin Board, 3-11
TOSHIBA ConfigFree, 3-10
TOSHIBA Disc Creator, 3-10, 4-16
TOSHIBA DVD PLAYER, 3-10
TOSHIBA DVD-RAM utility, 3-10
TOSHIBA Face Recognition, 3-11
using, 4-5
TOSHIBA Flash Cards, 3-9
TOSHIBA HDD/SSD Alert, 3-11
TOSHIBA HW setup, 7-1
TOSHIBA Media Controller, 3-11
TOSHIBA PC Diagnostic Tool, 3-9
TOSHIBA Power Saver, 3-9
TOSHIBA ReelTime, 3-11
TOSHIBA Service Station, 3-11
TOSHIBA zooming utility, 3-9
Touchpad, 2-7
control buttons, 2-7
problems, 8-9
using, 4-1
U
USB, 3-5
location, 2-2
problems, 8-13
USB mouse
problems, 8-10
V
Video RAM, 3-2
W
Web camera, 2-7, 3-6
using, 4-3
Wireless LAN, 3-6, E-3
function, 4-25
problems, 8-14