Scribd
Upload
370 views3 pages

Simulation of Halfwave Inverter Using Psim

This document provides instructions for simulating a half-wave inverter circuit using PSIM simulation software. It lists the required components, their parameters, and how to arrange them in the schematic. It describes the steps to build the circuit model in PSIM, run the simulation, and view the output voltage waveform across the resistor load and the switching waveforms of the IGBT switches. The aim is to simulate and observe these waveforms of a half-wave inverter circuit.

Uploaded by

Sidh Lodhi
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
370 views3 pages

Simulation of Halfwave Inverter Using Psim

This document provides instructions for simulating a half-wave inverter circuit using PSIM simulation software. It lists the required components, their parameters, and how to arrange them in the schematic. It describes the steps to build the circuit model in PSIM, run the simulation, and view the output voltage waveform across the resistor load and the switching waveforms of the IGBT switches. The aim is to simulate and observe these waveforms of a half-wave inverter circuit.

Uploaded by

Sidh Lodhi
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

SIMULATION OF HALFWAVE INVERTER USING PSIM

EX.NO: DATE:

Aim: To Simulate Half wave rectifier to observe the following waveforms by using PSIM.
(1) Output Voltage across R.
(2) Top and bottom waveforms of switch used(IGBT)

Requirements:

Table 1: Half wave inverter


Components Tool Box / Block parameters
Library browser

Voltage Source Elements /Source DC Amplitude = 230


/Voltage/Sine Frequency = 50

Switch Elements /Power IGBT


/Switch/IGBT Default

Load Elements /Power Resistor Resistance(Kilo ohm) = 100


/RLC Branches

Capacitance Elements/Power Capacitance Capcitance(micro faraday)=10


/RLC Branches

Gating pulse Elements/Power Gating block Top ON from 0-180’c


/Switch/Gating
block Bottom ON from 180-360’c

Procedure:
Steps to create Simulation Model using PSIM:
1. Click on File New.
2. Make/Model the circuit by placing all its Blocks from its corresponding Library/toolbox, which is
clearly shown in the table 1. Right click on the block to rotate mirror etc. to organize the circuit
elements.
3. To change the circuit parameters applicable to the block by double clicking on the block/element
and type the values. Keep the values default for some blocks like thyristor, diodes, mosfet etc.
4. To measure/observe the voltage across or current passes through the electrical block/device,
connect voltmeter blocks , it is available on the Elements/others/Probes/Voltmeter To observe the
waveform provide the clock from the simulate/simulation control provide time to observe the wave
form.
5. For Half wave inverter, components required and its parameter values tabulated in Table 1. The
schematic arrangement is shown in schematic diagram.

Steps to simulating the circuit using PSIM:


1. After correcting all errors start by creating a simulation.
2. To run the simulation, select simulate Run Simulation.
3. If any errors are reported here. Correct schematic or the simulation settings and re-run simulation.
4. To view simulation plots on simulation window, add the desired output name on the right side of
the window.
5. The waveforms obtained are shown in Fig 1, 2.

Schematic diagram: 1
Half wave inverter

G1
IGBT1
10u C1
vo 0 180.
V
R switch(IGBT1) is ON from 0-180.
Vin 100
switch(IGBT2) is ON from 180-360.
100k

G2
10u C2 IGBT2
180 360.
Output voltage and top, bottom(IGBT) Voltage waveform

Result:
A single phase half wave inverter model is created and analyzed the various waveforms by using
PSIM.

Inference:

You might also like