An Introduction to iSCSI

Presenter:
Mel Tsai
[email protected]

11/13/2002
1
 Outline
1) The basics of SCSI
2) Introduction to iSCSI
1) iSCSI vs. DAS/NAS/SAN
3) iSCSI Internals
• Initiators, Targets, Connections, and Sessions
• SCSI command encapsulation
• Ordered Delivery, Naming
4) TCP/IP offload engines
5) Summary: the pros and cons of iSCSI
6) Status of iSCSI 2
 SCSI Basics

• SCSI: Small Computer System Interface

→ Derived from the ca. 1979 “Shutgart Associates System
Interface” (SASI)

• The SCSI interface is used to attach hard disk drives, CD-

ROM drives, and other peripherals (e.g. scanners) to a host
machine

3
 SCSI Basics (cont.)

• SCSI-1, early 80’s

→ Original specification, disks accessed via a Common Command
Set (CCS), now OBSOLETE
• SCSI-2, mid-80’s
→ Backward compatible with SCSI-1, adds (faster) parallel
interfaces & broad support for non-disk devices (CDROM, tape,
scanners)
• SCSI-3, early 90’s to present
→ Adds many new standards, including the Fiber Channel Protocol
(FCP), serial packet protocol, low-voltage differential (LVD)
signaling

4
 Two faces of SCSI

• SCSI refers to two important entities:

→ The physical transport, i.e. the signaling & cabling for SCSI-
compliant devices

→ The higher-level data transmission protocol & formats

• (iSCSI uses the SCSI data transmission protocol, not the

physical transport)

5
 SCSI Transfer Modes
• "Regular" SCSI (SCSI-1)
• Wide SCSI
• Fast SCSI
• There is also an important • Fast Wide SCSI
difference between SCSI • Ultra SCSI
standards & SCSI transfer • Wide Ultra SCSI
modes • Ultra2 SCSI
• Wide Ultra2 SCSI
• Ultra3 SCSI
• Ultra160 (Ultra160/m) SCSI
• Ultra160+ SCSI
• Ultra320 SCSI

6
 SCSI Features

• SCSI has a “client-server” architecture model

→ Clients are initiators
→ Servers are targets

• Multiple SCSI initiators/targets on a single physical bus

→ Up to 16 devices on SCSI-2, prioritized by SCSI “Device ID”
number
→ Targets can be further divided into logical units, e.g. individual
disks in a multi-disk CD-ROM changer

7
 SCSI Features (cont.)

• Command queuing and reordering

→ Multiple outstanding commands can be served by the device a
better order than issued
→ SCSI disks can offer higher performance in a multi-user, multi-
tasking environment (e.g. vs. IDE/ATA drives)

• Rich command set:

→ Standard commands for formatting, polling, reading, writing, etc.
→ Specialized command sets for CD-ROMs, tape drives, scanners

8
SCSI Command-Descriptor Blocks

9
 iSCSI: SCSI over IP

• SCSI is already used everywhere

→ In direct-attached storage (DAS)
→ In devices connected to network-attached storage (NAS)
→ As the FC layer-4 block I/O protocol in Fibre Channel SANs

• Why iSCSI?
→ A low-cost alternative to FC SANs: remote storage can be
accessed via TCP/IP using the block I/O of SCSI
→ Better resource utilization because more clients can use the
pooled storage than possible with FC SANs
→ Interoperability: FC SAN equipment is often vendor-specific
10
 iSCSI vs. SANs

• Wide-area coverage:
→ It is costly to extend FC SANs beyond 10 km

• iSCSI does not necessarily replace the FC SAN:

→ iSCSI provides a low-cost method for extending the
reach of FC SANs by utilizing any existing IP
infrastructure
→ Cisco makes an FC-to-iSCSI router
→ FC SANs and iSCSI can be complementary
11
 iSCSI vs. NAS

• Primary advantage of iSCSI vs. NAS: Block I/O

→ NAS uses file I/O access such as NFS or CIFS
→ File I/O limits the performance of datacenter applications

• iSCSI makes remote storage look like a local SCSI drive

→ Simplifies management and setup of clients… all you need is an
Ethernet connection
→ Clients can structure data however they like, i.e. native ext3 or
NTFS
→ Backup is achieved by copying to the “local” SCSI disk

12
 iSCSI Deployment

• A major disadvantage of iSCSI and NAS is increased LAN

utilization
→ Higher latency when the LAN is saturated, especially during
backups

• Possible solution:
→ Build a dedicated IP network for your iSCSI traffic
→ This is still cheaper than FC

13
 iSCSI Competitors:

• Fibre Channel over IP (FCIP)

→ A “dumb” point-to-point IP tunnel between FC SANs

• Internet Fiber Channel Protocol (iFCP)

→ Slightly smarter than FCIP… Encapsulation FC
traffic in IP, maps individual FC devices to IP
addresses

14
 iSCSI Basic Operation

• Terminology:
→ Network Entities
→ iSCSI Nodes
• Initiators
• Targets
→ Network Portals

15
 iSCSI Sessions
• Only one iSCSI session can exist between an initiator/target pair
→ Normal sessions
→ Discovery sessions
→ Session IDs (SSIDs)

• Multiple parallel TCP/IP connections can exist in a session (CIDs)

16
 An iSCSI Session

• An iSCSI initiator logs in to an iSCSI target after

establishing a TCP connection
→ Various methods of client authentication

• After client authentication, a session is initialized

→ Via a driver on the client, the session encapsulates local SCSI
commands into remote iSCSI commands for the target
→ This is the “full-feature phase”
→ Block I/O data can be transferred securely, e.g. via IPSec

• Once finished, the session is terminated (logout & shutdown)

by either the initiator or target
17
 Some goals and requirements of iSCSI

• Does not require modification of TCP/IP infrastructure

• An initiator can attach to multiple network portals (IP

addresses) on a single target

• iSCSI sessions can operate over a single TCP/IP

connection and use TCP/IP connections conservatively

• iSCSI should support all SCSI-3 command sets

→ New feature of SCSI-3: device-to-device copy

18
 iSCSI Internals

• iSCSI wraps a local SCSI command into an iSCSI protocol

data unit (PDU) request
→ PDUs wrap the SCSI command descriptor blocks (CDBs)
→ The CDB and other info is placed in the PDU’s Basic Header
Segment (BHS)

• SCSI responses and status info from the target are returned
as iSCSI PDU responses

19
An iSCSI PDU

20
 In-order delivery of messages

• Sequence numbers, similar to TCP/IP

→ Commands
• Command sequence number (maintained by initiator)
• Expected command sequence number (maintained by target)
• Maximum command sequence number (maintained by target)
• “Immediate delivery” commands
→ Status
• Status sequence number (maintained by target)
• Expected status sequence number (maintained by initiator)
→ Data
• Data sequence numbers (reading from target)
• Request-to-transfer sequence numbers (writing to target)

21
 iSCSI Device Naming

• All iSCSI initiators/targets get a globally-unique World-

Wide Unique Identifier (WWUI)
• The WWUI is nice because:
→ Multiple iSCSI targets can exist behind a single IP address
→ The same target can exist behind multiple IP addresses
→ Initiators and targets can be referred to symbolically, independent
of their location
• A “complete” iSCSI address is made up of:
→ An IP address
→ A TCP/IP port (typically 3260)
→ The WWUI
22
 The iSCSI Killer: TCP/IP Overhead
• TCP/IP connections are expensive at high data rates
→ Connection establishment & teardown
→ Out-of-order packet reassembly
→ Error detection, packet retransmission
→ Expensive memory copying between protocol layers

• Transferring just 32 KB of data via TCP/IP can involve over 30

transactions between the NIC and CPU (20 data packets, 10 ACKs)

• Often-cited “rule” for TCP/IP overhead on a server:

→ You need a dedicated 1 GHz processor for 1 Gbit of TCP/IP traffic, and
a 10 GHz processor for 10 GbE

23
 Solution: TCP offload engines (TOEs)
• Implement the layer-4 TCP/IP stack with a separate CPU, NPU, or
ASIC
→ Now you can present the session layer (5) to the host

• TOEs can be integrated into standard Ethernet cards, iSCSI host

adaptors, or other iSCSI equipment

• TOEs will become an absolute requirement at speeds above 1 Gbps

due to server memory bandwidth limitations
→ Even PCI-X bandwidth cannot withstand 10 GbE without modification

• On the bright-side: Other applications (besides SANs) will soon need

TOEs!

24
 Summary: iSCSI Pros
1. iSCSI transforms directed-attached disks to network-attached, block
I/O devices
2. Existing SCSI RAID devices, tape libraries, etc. can be easily migrated
to your low-cost Ethernet iSCSI SAN with easy management
3. If the iSCSI network is separate from the primary LAN, you can get
LAN-free and server-free backup
4. Block I/O is better than File I/O for datacenter apps
5. High security
6. Potentially very fast… FC will be 2 Gbps tomorrow, while iSCSI
could be 10 GbE today
7. Interoperability vs. FC
8. No distance limitations

25
 Summary: iSCSI Cons
1. A standard 1 Gbps FC network is fundamentally faster than iSCSI at 1
Gbps due to protocol overhead
2. ASIC- or NPU-based TOEs are required for high performance
3. You still need a separate iSCSI IP network to achieve LAN-free
backup
4. Others?

26
 Where is iSCSI today?
• The iSCSI standard(s) are not yet finished

• There are several existing iSCSI products on the market, but it has a
while to go
→ 60 corporations are on the iSCSI working group of the SNIA.
→ Several shipping iSCSI host bus adaptors
→ Cisco makes an iSCSI to FC gateway

• Cisco has written a public domain Linux iSCSI kernel driver

→ A simple kernel module that implements an iSCSI initiator
→ Turns a remote iSCSI target (by specifying its IP address) into /dev/sda
or /dev/sdb, etc.

27
 References & Sources
• The PC Guide, www.pcguide.com
• SCSI Primary Commands - 2 (SPC-2), ISO/IEC 14776-312
• Cisco Whitepaper: “Introduction to iSCSI”
• “IP Storage Networking: IBM NAS and iSCSI Solutions,” IBM Redbook
• 10 Gigabit Ethernet Alliance: Introduction to TCP offload engine
• “The ins and outs of interconnects,” nwfusion.com
• “Inside iSCSI: Low-Cost Storage Networking”, extremetech.com

28