Optical Fiber Connections Joints and Couplers

Optical Fiber Connections
joints and couplers

Fiber Joints
• Optical fiber links with any line communication
system have a requirement for both jointing and
termination.
• A single mode fiber has continuous preform
length of around 200Km but such fiber spans
cannot be installed
Why we need joints
• Fiber can only be installed in lengths upto
2Km, for longer spans a joint is needed.
• For the repair of damaged fiber.
• For test purpose at terminal equipment.
• All of the fiber cable in a building cannot
be installed as one continues cable run.
• joints are needed to complete network
cabling.
• Temporary access is needed for test
purposes.
Fiber Pigtail
• Fiber optic transmitter and receivers are

terminated to a fiber optic Pigtail.
• A fiber pigtail is a short length of optical fiber
(usually 1 meter or less) permanently fixed to the
optical source or detector.
• Manufacturers supply transmitters and receivers
with pigtails and connectors
• Reduced coupling loss results when source-to-
fiber and fiber-to-detector coupling is done in a
controlled manufacturing environment
Fiber joint loss
• In fiber-fiber connection the optical loss
encountered at interface.
• The loss in optical power through a
connection is defined as
Po is the power emitted from the source fiber

Pi is the power accepted by the connected fiber
Fiber joint loss (cont…)
• Fiber-to-fiber connection loss is affected by intrinsic and extrinsic
coupling losses.
• Intrinsic coupling losses are caused by inherent fiber
characteristics.
• Extrinsic coupling losses are caused by jointing techniques.
sources of loss in Fiber-to-fiber joint
Fiber joint loss (cont…)
• Intrinsic coupling losses are limited by reducing fiber
mismatches between the connected fibers.
• This is done by procuring only fibers that meet stringent
geometrical and optical specifications
• Extrinsic coupling losses are limited by proper
connection procedures.
Fresnel Loss (Return Loss)
• When optical fibers are connected, optical power may be reflected back into
the source fiber.
• Light that is reflected back into the source fiber is lost.
• This reflection loss, called Fresnel reflection, occurs at every fiber interface.
• Fresnel reflection is caused by a step change in the refractive index that
occurs at the fiber joint.
Fresnel Loss
Reducing Fresnel Loss
• To reduce the amount of loss from Fresnel
reflection, the air gap can be filled with an index
matching gel.
• The refractive index of the index matching gel
should match the refractive index of the fiber core.
• Index matching gel reduces the step change in the
refractive index at the fiber interface.
Misalignment losses
These losses depends upon the fiber type , core diameter and
the distribution of the optical power.
End separation Loss
Fiber Splice
A permanent joint formed between two

individual optical fibers in the field or factory is
known as a FIBER SPLICE.
Used to establish long haul optical fiber links
Two types of splicing:
1. Fusion splicing

2. Mechanical splicing
Prior to splicing both fibers must be
prepared:
Remove plastic buffer coatings on both fibres
Cleave fibre end and clean with isopropyl alcohol
Good fibre end preparation is vital if a low loss splice
is to be achieved.
Fusion Splice
 Melts the fibers together to form a
continuous fiber
 The source of heat is usually an
electric arc, but can also be a laser, or a
gas flame, or a tungsten filament
through which current is passed.
Fusion Splice Principles
Cleaved fiber ends are fused permanently together

using an electric arc
During splicing fibers area held in V-grooves for

alignment
A variety of splices have developed to cater for

multimode and singlemode fiber
Cleaving Steps
Fiber End Face
Steps in Fusion Splice Process
Fusion Splice loss
Which Splice?
 If cost is the issue, we've given you the clues to make a choice:
fusion is expensive equipment and cheap splices, while
mechanical is cheap equipment and expensive splices. So if you
make a lot of splices (like thousands in an big telco or CATV
network) use fusion splices. If you need just a few, use
mechanical splices. Fusion splices give very low back reflections
and are preferred for singlemode high speed digital or CATV
networks. However, they don't work too well on multimode
splices, so mechanical splices are preferred for MM, unless it is
an underwater or aerial application, where the greater reliability
of the fusion splice is preferred.

Optical Fiber Connections Joints and Couplers

Uploaded by

Copyright:

Available Formats

Optical Fiber Connections Joints and Couplers

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Optical Fiber Connections Joints and Couplers

Uploaded by

Copyright:

Available Formats

Optical Fiber Connections

joints and couplers

• Fiber optic transmitter and receivers are

Po is the power emitted from the source fiber

A permanent joint formed between two

Two types of splicing:

1. Fusion splicing

Cleave fibre end and clean with isopropyl alcohol

Good fibre end preparation is vital if a low loss splice

Cleaved fiber ends are fused permanently together

During splicing fibers area held in V-grooves for

A variety of splices have developed to cater for

You might also like