AT89ISP Programmer Cable

Introduction AT89ISP
This Application Note describes the Atmel® AT89ISP cable interface; this in-system
programmer cable communicates serially with Atmel’s AT89S microcontrollers and Programmer
reprograms them in the circuit without removal. For surface-mounted devices, elimi-
n a t i n g t h i s s t e p gr e a t l y r e d u c e s t h e p o s s i b i l i t y o f d a m a g e s c a u s e d by Cable
inser tion/removal of delicate leads, and allows for design changes and soft-
ware/parameter updates in the field.

AT89ISP Software
Application
The Atmel Microcontroller ISP Software is the primary means for performing in-system Note
programming (ISP) of Atmel AT89S devices. It provides an intuitive interface for in-sys-
tem programming that can be run from a personal computer. The software will run
under the Windows®9x/ME/2000/NT® operating systems. The Atmel ISP software has
a comprehensive set of features that allows a user to view, program, and erase data
from an Atmel AT89S device. A detailed Adobe® Acrobat® document describing the
features/functions of the software accompanies it.

AT89ISP Cable
In order to use the Atmel Microcontroller ISP Software, the user will need to have an
Atmel AT89ISP cable. The ISP cable’s pins need to be connected to an AT89S device
in the manner shown in Figure 1. The 25-pin male connector plugs into the parallel
port of the user’s personal computer. The 10-pin female IDC header plugs into a 10-
pin male header in the user’s target board. A polarized 10-pin receptacle male header
is highly recommended. The pin-out shown below represents the target 10-pin male
header connector in the user's board as viewed from the top.

Figure 1. AT89ISP Cable 10-pin Male Header Pinout

(SCK) P1.7 1 2 GND

(MISO) P1.6 3 4 VCC

RST 5 6 NC

NC 7 8 NC

(MOSI) P1.5 9 10 GND

Rev. 3310A–MICRO–11/02

1
Connection The correct way to connect the female header end of the AT89ISP cable to the 10-pin
receptacle male header is to align the connector “arrow” towards pin 1, as illustrated in
Figure 2. On the cable casing end, make sure the connector “arrow” sits visible next to
the side of the small PC board (not away from it).

Figure 2. Proper Cable Alignment

1 2

9 10

Table 1. ATMEL AT89ISP Cable Pinout

Pin Name Comment
1 SCK Serial Clock
3 MISO Master In – Slave Out
4 VCC Target Power Supply
5 RST Target MCU Reset
9 MOSI Master Out – Slave In
2, 10 GND Common Ground
6, 7, 8 NC No Connection

Figure 3. AT89ISP Target Board Sample Connection

10-pin Male
Atmel AT89ISP Cable Header

User Target Board

Parallel Port 20-/40-pin

Socket

VCC

Voltage Levels The AT89ISP cable requires a regulated DC supply from the user target board. The
cable should operate correctly between the specified operating voltage limits. The cur-
rent operating VCC voltage range for the AT89ISP cable is 3.3V to 5.5V.

2 AT89ISP Programmer Cable

3310A–MICRO–11/02
 Atmel Headquarters Atmel Operations
Corporate Headquarters Memory RF/Automotive
2325 Orchard Parkway 2325 Orchard Parkway Theresienstrasse 2
San Jose, CA 95131 San Jose, CA 95131 Postfach 3535
TEL 1(408) 441-0311 TEL 1(408) 441-0311 74025 Heilbronn, Germany
FAX 1(408) 487-2600 FAX 1(408) 436-4314 TEL (49) 71-31-67-0
FAX (49) 71-31-67-2340
Europe Microcontrollers
Atmel Sarl 2325 Orchard Parkway 1150 East Cheyenne Mtn. Blvd.
Route des Arsenaux 41 San Jose, CA 95131 Colorado Springs, CO 80906
Case Postale 80 TEL 1(408) 441-0311 TEL 1(719) 576-3300
CH-1705 Fribourg FAX 1(408) 436-4314 FAX 1(719) 540-1759
Switzerland
TEL (41) 26-426-5555 La Chantrerie Biometrics/Imaging/Hi-Rel MPU/
FAX (41) 26-426-5500 BP 70602 High Speed Converters/RF Datacom
44306 Nantes Cedex 3, France Avenue de Rochepleine
Asia TEL (33) 2-40-18-18-18 BP 123
Room 1219 FAX (33) 2-40-18-19-60 38521 Saint-Egreve Cedex, France
Chinachem Golden Plaza TEL (33) 4-76-58-30-00
77 Mody Road Tsimshatsui ASIC/ASSP/Smart Cards FAX (33) 4-76-58-34-80
East Kowloon Zone Industrielle
Hong Kong 13106 Rousset Cedex, France
TEL (852) 2721-9778 TEL (33) 4-42-53-60-00
FAX (852) 2722-1369 FAX (33) 4-42-53-60-01

Japan 1150 East Cheyenne Mtn. Blvd.

9F, Tonetsu Shinkawa Bldg. Colorado Springs, CO 80906
1-24-8 Shinkawa TEL 1(719) 576-3300
Chuo-ku, Tokyo 104-0033 FAX 1(719) 540-1759
Japan
TEL (81) 3-3523-3551 Scottish Enterprise Technology Park
FAX (81) 3-3523-7581 Maxwell Building
East Kilbride G75 0QR, Scotland
TEL (44) 1355-803-000
FAX (44) 1355-242-743

e-mail
[email protected]

Web Site
http://www.atmel.com

© Atmel Corporation 2002.

Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty
which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors
which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does
not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted
by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical
components in life support devices or systems.

ATMEL ® is the registered trademark of Atmel.

Windows ® and Windows NT® are the registered trademarks of Microsoft Corporation.
Adobe ® and Acrobat ® are the registered trademarks of Adobe Systems Incorporated. Printed on recycled paper.
Other terms and product names may be the trademarks of others.
3310A–MICRO–11/02 xM