Urea 6

UREA PLANT
Introduction
• Urea (identified 1773), the first organic compound prepared
by inorganic synthesis (1828 Wohler)
NH3 + HCNO → CO(NH2)2
• Commercial production started in 1922 – Germany, 1932 –
USA and 1935 – UK.
• Urea has been considered as slow – release fertilizer since it
must undergo two transportation
1. Hydrolysis:
2. Nitrification: NH3 → Nitrite or Nitrate (Microbes, moist and warm soil )
• Biuret is the impurity in urea.
• More than 50 M tons is produced annually
Uses of Urea
• Main N2 fertilizer, specially for the flooded region.
• Cattle feed supplement where it is cheap.
• Feed material for melamine plastics and various
glues (Urea – Formaldehye, urea – melamine –
formaldehyde)
• Use: Prill or microprill (0.2-0.4 mm), liquid mixture of
urea (±75% solution), molasses, phosphoric acid.
Properties of Urea
Molecular weight 60.06
N2 Content, % 46.6
Color White
Specific gravity 1.335
Melting point oC 132.7
Critical relative humidity
20oC 81%
30oC 73%
Specific heat 20oC, Cal/goC 0.32
Heat of solution in water (endothermic) -57.8
Cal/goC
Process Operating Variables
Reactions:
2NH3+ CO2 → H2NCOONH4
H2NCOONH4 → H2NCONH2 + H2O
Temperature:
• Rate of Carbamate decomposition reaction increases
with temperature. It is slow at < 150oC (NH3:CO2,
stoichiometric) and quite rapid at 210oC.
• 180-210 oC in 0.3 to 1.0 hr is optimum for most process.
At high temperature, corrosion rate is high.
Pressure:
• Preferred pressure is 140 – 250 atm.
Mole ratio of NH3: CO2
• Excess ammonia above the stoichiometric ratio
favors the rate of reaction. (3:1 = NH3: CO2)
Other factors:
• The presence of water decreases conversion.
• The presence of small amount of O2, decreases
corrosion.
Optimum Conditions
• Maximize the production of urea per unit time with
due regard to cost of recycling unreacted NH3 and
CO2, the cost increase of reactor size, corrosion
difficulties. NOT to increase the percentage of
conversion.
Typical Operating Conditions:
T: 180 – 210oC NH3:CO2 = 3.1 - 4.1
P: 140 – 250 atm Retention time: 20-30 min
Urea Processes
 Once – Through
 Partial recycle
 Total recycle (All new plants)
 Stamicarbon: ZFCL, KAFCO
 Snamprogetti (Snam): JFCL
 Mitsu – Toatsu (M – T): UFFL Before 1990.
 Advanced Cost and Energy Saving (ACES) by TEC: UFFL
(After 1990), CUFL
Once Through Process
35 % NH3 conversion
75% CO2 conversion
Ammonium Nitrate
Ammonium Sulfate
Nitric Acid
Ammonium Phosphate
200 atm, etc
100 % excess 185oC
80% urea
• The once – through process is simplest and least expansive
(both capital and operating cost) among the three process.
• Least flexible and cannot be operated unless some provision is
made to utilize large amount of ammonia and off-gas.
Partial Recycle Process

• Part of the off – gas is recycled back to the reactor.
• The amount of ammonia is reduced to 15% to that of once
through that must be used in other processes.
• Investment cost is somewhat lower than the total recycle
process, this advantage apparently does not compensate the
inflexibility arising from the necessity to operate a co-product
plant with mutual interdependency problems. However it
finds application in UAN co-product plants.
80% urea
70 % NH3 conversion
87 % CO2 conversion
200 atm,
185oC
100-110 % excess
( Mitsui – Toatsu )
Total Recycle Processes
• All unconverted NH3 and CO2 is recycled back to the
reactor (99% conversion).
• No nitrogen co-product is necessary.
• Most flexible urea process as it depends only NH3
and CO2 supply.
• Most expensive in investment and operating cost.
Classification of Total recycle Processes
Reactor outlet contains UREA, NH3, CO2, H2O, and
CARBAMATE which must be decomposed before
recycle.
 Hot – gas mixture recycle

 Separated gas recycle Carbamate
Decomposition
 Slurry recycle
 Carbamate - solution recycle Modern Processes:
 Stripping Snam,
Stamicarbon, ACES
The general design objectives are:
• Maximize the heat recovery
• Minimize the amount of carbamate solution recycled (smaller
pumps and less power) and amount of water returned to the
reactor (better conversion).
• Minimize power requirement
• Maximize ammonia recovery (lowering operating cost and less
pollution)
• Other important requirement is of-course minimizing
investment. The problem is finding the best balance between
the utility consumption and maintenance on one hand and
investment on the other hand.
Urea Manufacturing Process
Desired 2NH3 (liquid) + CO2 (gas) = NH4COONH4 +38.06 Kcal/mol
Reactions NH4COONH4= NH2CONH2 + H2O -522 Kcal/mol
Undesired
Reaction
Reduce yields of Urea,

Burns the leaves of plants
Three major design considerations:
• to separate the urea from other constituents,
• to recover excess NH3 and
• decompose the carbamate for recycle.
Block Diagram of Urea Synthesis
150-240 bar
17 bar, 2 bar, -0.35bar

68 %
99%
(Mitsui – Toatsu)
Stripping Process Based Plants
• In 1966 Stamicarbon of Netherland introduced CO2 stripping
→ Snamprogetti built a plant using NH3 as stripping process
(requires high NH3:CO2 ratio) later switched to thermal
stripping → Toyo Engineering Corpora on (TEC) Japan
utilized CO2 stripping.
• Three licensors have different approaches and have improved
their technology throughout the years.
 Closely stoichiometric amount of raw material consumption
 Reduced steam consumption to an apparently economic level
 Avenues available for improvements in reduction of capital cost,
improved reliability and efficiency of mechanical improvements and
advances in metallurgical advances.
Snamprogetti process
Six section
• Synthesis and high pressure (HP) recovery (160 bar)
• Medium pressure (MP) purification and recovery (17 bar)
• Low pressure (LP) purification and recovery (3.5 bar)
• Vacuum concentration (2 steps: 0.3 and 0.03 bar abs)
• Process condensate treatment
• Finishing: prilling and granulation
Snamprogetti Process Flow Diagram
205oC
155oC
Key Features of Snamprogetti Process
ACES plant (UFFL)
1990 – Renovation. From 1994 – ACES is operating
Five section
• Synthesis sections
• Purification section
• Concentration and prilling section
• Recovery section
• Process condensate treatment section
Class Test 2
Date: 14 August, 2010 (or Next available date after 14)
Syllabus: Stamicarbon, Snamprogetti and ACES
process.
Free Tips: Memorize as much as you can !!!!

Urea 6

Uploaded by

Copyright:

Available Formats

Urea 6

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Urea 6

Uploaded by

Copyright:

Available Formats

What are the main reactions involved in urea synthesis?

What are the typical operating conditions for urea synthesis?

UREA PLANT

Partial Recycle Process

 Hot – gas mixture recycle

Reduce yields of Urea,

17 bar, 2 bar, -0.35bar

You might also like