0% found this document useful (0 votes)
55 views2 pages

Relative Resource Manager

This document provides assembly instructions for a data burst controller circuit board (rev 1). It includes a list of components, drilling details, assembly details, and a parts list. The summary instructions are to: 1) fit and solder all resistors, 2) fit and solder the microcontroller socket, trimpot, switch, and veropins, 3) fit and solder connectors and LED, 4) fit header links and rubber feet, and 5) test with programmed microcontroller.

Uploaded by

vasireddysamrat
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
55 views2 pages

Relative Resource Manager

This document provides assembly instructions for a data burst controller circuit board (rev 1). It includes a list of components, drilling details, assembly details, and a parts list. The summary instructions are to: 1) fit and solder all resistors, 2) fit and solder the microcontroller socket, trimpot, switch, and veropins, 3) fit and solder connectors and LED, 4) fit header links and rubber feet, and 5) test with programmed microcontroller.

Uploaded by

vasireddysamrat
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Data Burst Controller – Rev 1

R6
J5 RELEASED
10k
Data2 Approved for student use
R4
100R

VDD

J6

R1
22k Data
J7

R2
Clock
100R
J3
SW1

Sync
VDD

VDD

J1
U1 R3
7 10k
GP0/AN0
6 +5V
GP1/AN1/VREF R5
5 J2
GP2/T0CKI/INT/AN2 1k
4 1
GP3/MCLR C1
3 2
GP4/T1G/OSC2/AN3 100n
2 3
GP5/T1CKI/OSC1
PIC12F675 VDD = 1 CONN-SIL3
VSS = 8 LD1
J4 J8 LED

C2 I/P 0V
100n
J9
1

1
RV1 2
3 3

Trimpot 47k CONN-SIL3


2

Originated by: PC On date: 01/12/04 Title: Data Burst Generator


the University of Greenwich
Revised by: ASR On date: 03/11/10 Doc No: SOE XXXX
School of Engineering
Approved by: On date: Filename: BData#1.DSN
Project No: Sheet 1/1 Revision: 1

Drilling Details – Solder Side

Drill 1.0mm (5 pos’n) Drill 1.0mm (4 pos’n)

Data Burst (Rev 1)

Drill 1.0mm (2 x 3 pos’n)

Drill 5.0mm (4 pos’n) Drill 1.0mm (2 pos’n)


Assembly Details – Component Side

Parts List Assembly


Qty Part Ref’s Value
1 PCB Rev 1 There are no thru-hole pins in this PCB
1 R1 Res 22k 0.25W 5% 1. Fit all the resistors and solder
2 R2, R6 Res 10k 0.25W 5%
2 R3, R4 Res 100R 0.25W 5%
1 R5 Res 1k0 0.25W 5% 2. Fit U1 socket, trimpot, switch and
solder in place.
1 C1 Cap 100n 50V Cer
3. Fit all 7 veropins from the top and
1 U1 Skt IC 8W T/P solder.
1 U1 IC PIC12F675 Micro

1 RV1 Res Trim 47k Vert


4. Fit and solder the LED and both SIL
1 LD1 LED – 3mm Red connectors.
1 SW1 Switch 6x6 T/H
5. Finally fit the 2 header links and the 4
2 J2, J9 Con SIL3 rubber feet.
2 J2, J9 2W header link
7 J1, J3 - 8 Veropin D/S Fit the programmed 12F675
4 Rubber Feet – 12mm
microcontroller supplied separately and test
the PCB.
Optional

1 C2 Cap 100n 50V Ceramic

You might also like