N.

I COLLEGE OF ENGINEERING, KUMARACOIL

PART A (2MARKS) AND PART B (16 MARKS) QUESTIONS

WITH ANSWERS

AE1402 COMPOSITE MATERIALS AND STRUCTURES

SEMESTER VII, DEPARTMENT OF AERONAUTICAL

ENGINEERING

PART A
Unit1

1. What are the major constituents in composite materials?

Reinforcing phase
One in which it is embedded is called the matrix.
Reinforcing phase - Fibres, particles or flakes.
Matrix- Materials are generally continuous.

2. Define lamina.
A lamina (also called a ply or layer) is a single flat layer of unidirectional
fibers or woven fibers arranged is a matrix.

3. Define laminate.
A laminate is a stack of plies of composites. Each layer can be laid at various
orientations and can be different material systems.

4. Define Hooke’s law.

Within elastic stress is proportional to strain. (e.g) Spring balance.
5. Write compliance and stiffness matrices for Hooke’s law stress-strain
relationships at a point in an x-y-z orthogonal system.
 1 ν ν 
 E − E − E o o o
 
εx  − ν 1
−
ν
o o o   σx 
εy   E E E   σy 
   ν ν  
o o o   σz 
1
εz  − E − E E 
 = 1  
γyz   o o o o o  τyz 
γzx   G  τzx 
   1  
γxy   o o o o o  τxy 
G 
 1
 o o o o o 
 G

6. What are advanced composites?

Advanced composites are composite materials which are traditionally used
in the aerospace industries. These composites have high performance
reinforcements of a thin dia. in a matrix material such as epoxy and
aiuminium.

7. List down the reinforcement materials and resins used in composite

materials.
Reinforcement materials
Graphite, Glass, Aramid, Kevlar 49, Boron
Resins
Epoxy, aluminium, Polyamide, Nylon, Polyesters, Vinyl esters, Phenolics,
Polymides, Polybenzimidazoles, Polyphenylquinoxaline.

8. Why are fiber reinforcements of a thin diameter?

(i) As the fibers become smaller in diameter , it reduces the chances of an

2
 inherent flaw in the material.
(ii) Fixed fiber volume in a given volume of composite, the area of the fiber-
matrix interface is inversely proportional to the diameter of the fiber.
(iii) Ability to bend increases with a decrease in the fiber diameter and is
measured as flexibility.

9. What are the aircraft structural components made of composite materials?

Elevator face sheets, Horizontal stabilizer, Wing spoilers, ailerons, rudders,
elevators, fairings etc.,
Skin on the horizontal stabilizer box, Under wing fairings, fin, rudder and
stabilizer skins, skins on vertical fin box, fin leading edge, wing skins,
horizontal and vertical tail boxes ; wing and tail control surfaces etc., Wing
skins and sub structure; forward fuselage; horizontal stabilizer flaps;
ailerons.
10. Explain the difference between isotropic and anisotropic materials.
Anisotropic materials are the opposite of isotropic materials like steel and
aluminium. Anisotropic materials have different properties in different
directions. For example, the Young’s modulus of a piece of wood is higher
(different) in the direction of the grain than in the direction perpendicular to
the grain. In comparison, a piece of steel has the same young’s modulus in
all directions.

11. What are the material constants of an orthotropic materials?

For an orthotropic material, the nine independent elastic constants are E11,
E22, E33, G12, G13, G23, ν 12, ν 13, ν 22.
Uni-directionally oriented fiber composites are a special class of
orthotropic materials. If the fibers are in the 1-2 plane, elastic properties are
equal in the 2-3 directions so that E22=E33, ν 12=ν 13 and G12=G13. Further
more G23 can be expressed in terms of E22 and ν 12. Thus the number of
independent elastic constants for a unidirectionally oriented fiber composite
reduces to 5. Such composites are often called transversely isotropic.

12. What are the properties of matrices? Write down its usage.
Properties
Low viscosity.
High melting point.
Low curing temperature.
Usage:

To transfer stresses between the fibers.

To provide a barrier against an adverse environment.
To protect the surface of the fibers from mechanical abrasion.
13. Define (a) Orthotropic material (b) isotropic material and give the number of
elastic constants in macro mechanics.
If a material has three mutually perpendicular planes of material symmetry it
is called orthotropic material. Three mutually perpendicular planes of
material symmetry also imply that there are three mutually perpendicular
planes of material symmetry. Note there are nine independent elastic
constants.

3
 If all planes in an orthotropic body are identical, it is an isotropic material.
This also implies that there are infinite principal directions. Note that there
are two independent constants.

14. What is meant by orthogonally isotropic material? Give an example.

The Q16 qnd Q26 terms are non-zero when has any value other than 0º or
90º. This indicates the anisotropic behaviour of an orthotropic lamina when
its fibers are not oriented along or perpendicular to the reference load
direction. The terms Q16 and Q26 are that cause an orthotropic lamina to
behave like an anisotropic lamina in a laminate, when is neither 0º nor
90º.(Better 30º and 60º).

15. Define composite materials.

A composite is a structural material which consists of combining two or
more constituents. The constituents are combined at a macroscopic level and
are not soluble in each other. One constituent is called the reinforcing phase
and the one in which it is embedded is called the matrix.
16. What is an isotropic body?
A isotropic material has properties that are the same in all directions. For
example the Young’s modulus of steel is the same in all directions.

17. Write four applications of composite materials?

Air craft. Space, automotive, sporting goods and marine engineering.

18. Distinguish between long fibers and short fibers.

Long fibers: Easy to orient & process. Impact resistance, low shrinkage,
improved surface finish and dimensional stability.
Short fibers : Low cost, Easy to work with matrix. Short fibers have few
flaws and therefore have higher strength.

19. What is a particulate composite?

It consists of particles immersed in matrices such as alloys and ceramics.
They are usually isotropic since the particles are added randomly.

20. What is an anisotropic material?

At a point in anisotropic material, material properties are different in all
directions. The material which has 21 independent elastic constants at a point
is called an anisotropic material.

4
Unit 2

1. What are the assumptions made in the strength of materials approach model?
(i)The bond between fibers and matrix is perfect.
(ii) The elastic moduli, diameters and space between fibers are uniform.
(iii)The fibers are continuous and parallel.
(iv)The fibers and matrix follow Hooke’s law.(linearly elastic)
(v)The fibers possess uniform strength.
(vi)The composite is free of voids.

2. Find the in-plane shear modulus of a glass/epoxy lamina with a 70% fiber
volume fraction. Gf = 35.42 GPa; Gm = 1.308 GPa.
1 0. 7 0.3
= +
G12 35.42 1.308
G12 = 4.014GPa

3. Define micro mechanics.

Micro mechanics is the study of composite material behaviour wherein the
interaction of the constituent materials is examined on a microscopic scale to
determine their effect on the properties of the composite material.

4. Find the transverse Young’s modulus of a glass/epoxy lamina with a 70% fiber
volume fraction. Ef = 85 GPa; Em = 3.4GPa.
1 Vf Vm
= +
E 2 Ef Em
0.7 0.3
= +
85 3.4
E2 = 10.37 GPa.

5. Distinguish between natural axis and arbitrary axis.

The axis parallel to the nominal axis, it is called natural axis or right hand co-
ordinate system.
The axis is some inclining of plane is called arbitrary plane.

6. What is macro mechanics?

The macro mechanical analysis of a lamina is based on average properties and
by considering the lamina to be homogeneous. Methods to find these average
properties based on the individual mechanical properties of the fiber and the
matrix.

7. Define material axes or local axes.

The axes in the 1-2 co-ordinate system are called the local axes or the material
axes. The direction 1 is parallel to the fibers and the direction 2 is
perpendicular to the fibers. Direction 1 is also called the longitudinal direction
(L) and the direction 2 is called the transverse direction (T). The axes in the x-y
co-ordinate system are called the global axes or the off axes.

5
 8. What is density of composites?
The mass of composite (Wc) is the sum of the mass of the fibers (Wf) and the
mass of the matrix (Wm) is
Wc= Wf + Wm
The density of the composite in terms of mass fraction
1 Wf Wm
= +
ρc ρf ρm

9. What is elasticity approach?

Elasticity accounts for equilibrium of forces, compatibility and Hooke’s law
relationships in three dimensions, whereas the strength of materials approach
may not satisfy compatibility and not account for Hooke’s law in three
dimensions.

10. What is major poisson’s ratio?

The major poisson’s ratio is defined as the negative of the ratio of the normal
strain in the transverse direction to the normal strain in the longitudinal
direction, when a normal load is applied in the longitudinal direction.

11. Write the general characteristics of composite materials.

Low specific gravity.
High strength weight ratio.
High modulus-weight ratio.

12. What is meant by “stiffness”.

A measure of modulus
The relationship of load and deformation
The ratio between the applied stress and resulting strain.

13. Write short notes on: Resilience.

A property of a material, which is able to do work against restraining, forces
during return from a deformed condition.

14. What are the assumptions made in micro mechanics?

Micro mechanics – The study of composite material behaviour wherein the
interaction of the constituent materials is examined in detail as part of the
definition of the behaviour of the heterogeneous composite material.
The two basic approaches to the micromechanics of composite materials are
(i) Mechanics of materials
(ii) Elasticity
The mechanics of materials (or strength of materials or resistance of materials)
approach embodies the usual concept of vastly simplifying assumptions
regarding the hypothesized behaviour of the mechanical system. The elasticity
approach actually is at least three approaches (i) bounding principles (ii) exact
solutions and (iii) approximate solutions. All approaches are characterized by
more rigorous satisfaction of physical laws (equilibrium, deformation
continuity and compatibility and stress-strain relations) than in mechanics of
materials.

6
15. What is fiber reinforced plastic (FRP)?
A general term for a composite that is reinforced with cloth, mat, strands or any
other fiber form.

16. Define the term: constituent.

In general, an element of a larger grouping. In advanced composites, the
principal constituents are the fibers and the matrix.

17. What is a homogeneous body?

A homogeneous body has properties that are the same at all points in the body.
A steel rod is an example of a homogeneous body. However, if one heats this
rod at one end, the temperature at various points on the rod would be different.
Since young’s modulus of steel varies with temperature, we no longer have a
homogeneous body.

18. What is a non homogeneous body?

A non-homogeneous or inhomogeneous body has material properties which
are a function of the position on the body.

19. How local and global stresses are related?

The global and local stresses in an angle lamina are related to each other
through the angle of the lamina,

 σx  σ1 
 σy  = [T ]−1  σ 2 
   
τxy  σ 12
Where [T] is called the transformation matrix and is defined as

c 2 s2 − 2 sc 
 
[T]-1 =  s 2 c 2
2 sc 
 sc − sc c 2 − s 2 


20. What are the elements of the transformed reduced stiffness matrix ?
−−

Q 11 = Q11 C 4 + Q22 S 4 + 2(Q12 + 2 Q66 ) S 2 C 2

−−

Q 12 = (Q11 + Q22 − 4 Q66 ) S 2 C 2 + Q12 (C 4 + S 4 )

−−

Q 22 = Q11 S 4 + Q22 C 4 + 2(Q12 + 2 Q66 ) S 2 C 2

7
−−

Q 16
= (Q11 − Q12 − 2 Q66 ) C 3 S − (Q22 − Q12 − 2 Q66 ) S 3C

−−

Q 26 = (Q11 − Q12 − 2 Q66 ) C S 3 − (Q22 − Q12 − 2 Q66 )C 3 S

−−

Q 66
= (Q11 + Q22 − 2 Q12 − 2 Q66 ) S 2 C 2 + Q66 ( S 4 + C 4 )

8
Unit 3

1. Distinguish between symmetric cross ply laminate and symmetric angle ply
laminate.
Symmetric cross ply laminates
Odd no. of plies
[0/90/0/90/0]
Symmetric angle ply laminates
+ and – directions
Odd no. of plies
[-40/40/-40/40/-40]

2. Give an example of a laminate with zero coupling stiffness matrix,

Symmetric laminates
A laminate is called symmetric if the material, angle and thickness of plies are
the same above and below the mid-plane. A example of symmetric laminates is
[0/30/ 60 ]s as shown below:
/0/30/60/30/0/
For symmetric laminates from the definition of [B] matrix, it can be proved
[B]=0. Hence

 Nx  A11 A12 A16  ε x 

°

 Ny = A12 A22 A26 ε ° 


    y 
 Nz  A16 A26 A66 ε ° 
 z
 Mx  D11 D12 D16   κx 
 My = D12 D22 D26  κy 
    
 Mz  D16 D26 D66  κz 

3. What are the merits and demerits of Tsai-hill failure theory?

The variation of strength with angle of lamina orientation is smooth rather than
having cusps that are not seen in experimental results.
The strength continuously decreases as grows from 0º rather than the rise in
uni-axial strength that is characteristic of both the maximum stress and the
max. strain criteria.
The agreement between the criterion and experiment is even better than that at
first glance. The maximum stress and strain criteria are incorrect by100% at
30º.
Considerable interaction exists between the failure strengths X,Y,S in the Tsai-
hill criterion but none exists in the previous criteria where axial, transverse and
shear failures are presumed to occur independently.

4. Give examples of anti symmetric angle ply and symmetric cross ply laminates.
Anti-symmetric angle ply
[-40/40/-40/40]
Symmetric cross ply laminate
[90/0/90/0/90]

9
 5. Define cross ply laminate and angle ply laminate.
Cross ply laminates
A laminate is called a cross ply laminate (also called laminates with specially
orthotropic layers) if only 0º and 90 º plies were used to make a laminate. An
example of a cross ply laminate is a (0/90/90/0/90] laminate.
Angle ply laminates
A laminate is called an angle ply laminate if it has plies of same material and
thickness, and only oriented at + and – direction. An example of an angle
ply laminate is [-40/40/-40/40].

6. What are the assumptions made in classical small deformation theory for a
laminate?
(i)Each lamina is orthotropic.
(ii)Each lamina is homogeneous.
(iii)A line straight and perpendicular to the middle surface remains straight and
perpendicular to the middle surface during deformation (γxz = γxz = 0)
(iv)A straight line in the z-direction remains of constant length (εz =0).
(v)The laminate is thin and is loaded only in its plane. (plane stress) (σz = τxz=
τxz=0)
(vi)Displacements are continuous and small throughout the laminate.
(│u│, │v│, │w│<<laminate thickness).
(vii)Each lamina is elastic.
(viii)No slip occurs between the lamina inter faces.

7. Define inter laminar stresses with causes.

In classical lamination theory no account is taken of stresses such as σzx, τzx and
τzy which are shown on an element of an angle-ply laminate loaded with Nx.
These stresses are called inter laminar stresses and exist on surfaces between
adjacent layers although they exist within the layers but are usually largest at
the layer interfaces.
Accordingly, classical lamination theory does not include some of the stresses
that actually cause failure of a composite laminate.

8. Define: Laminate code.

A laminate is made of a group of a single layers bonded to each other. Each
layer can be identified by its location in the laminate, its material and its angle
of orientation with a reference axis. Each lamina is represented by the angle of
ply and separated from other plies by a slash sign. The first ply is the top ply of
the laminate. Special notations are used for symmetric laminates, laminates
with adjacent lamina of same orientation or of opposite angles and hybrid
laminates.

9. Define: Quasi-isotropic laminate.

A laminate approximating isotropy by orientation of plies in several or more
directions.

10. What is inter laminar shear?

A shearing force tending to produce a displacement between two laminae along
the plane of their interface.

10
11. Define the term: Balanced laminate.
A laminate in which all the plies are at angles other than 0º and 90º and occur
in ±pairs. The plies are symmetrical about the centre line.

12. What are the equations of [A],[B] and [D] matrices?

3
−
Aij = ε Q  ( hk − hk − 1) , i= 1,2,3; j=1,2,3
 k
k =1 ij

1 3 −
Bij = ε Q  ( hk 2 − hk 2 − 1) i=1,2,3; j=1,2,3
2 k =1 ij  k
1 3 −
Dij = ε Q  ( hk 3 − hk 3 − 1) ,i=1,2,3; j=1,2,3
3 =1 ij  k
k

13. What are the transverse equations for laminated plates?

The equilibrium differential equations in terms of the force and moment
resultants derived and the transverse loading p(x,y) are
Nxx + Nyy=0
Nxy,x+ Ny,y=0
Mx,xx+2Mxy,xy+My,yy=-p
Where a comma denotes differentiation of the principal symbol with respect to
the principal symbol with respect to the subscript that follows the comma.

14. What is hybrid laminate?

−− −−
Graphite/Epoxy 0
−− −−
Boron/Epoxy 45
−−−−
Boron/Epoxy − 45
−−−− −
Boron/Epoxy − 45
−−−− −
Boron/Epoxy 45
−−−− −
Graphite/Epoxy 0
− −−−

[0Gr/±45B]s denotes the above laminate. It consists of six plies but the 0º plies
are made of graphite/epoxy, while the angle plies are made of boron/epoxy.

15. What is maximum strain failure theory?

This theory is based on the Maximum Normal strain theory by St. Venant and
the Maximum shear stress theory by Tresca as applied to isotropic materials.
The strains applied to a lamina are resolved to strains in the local axes. Failure
is predicted in a lamina, if any of the normal or shearing strains in the local
axes of a lamina or exceed the corresponding ultimate strains of the
unidirectional lamina. Given the strains /stresses in an angle lamina, find the
strains in the local axes. A lamina is considered to be failed if
- (ε 1c )ult < ε 1 < (ε 1t )ult
- (ε 2c )ult < ε 2 < (ε 2c )ult
or
- (γ 12 )ult < γ 12 < (γ 12 )ult

11
16. What are the types of hybrid laminates?
Interply hybrid laminates
Intraply hybrid composites
Interply-intraply hybrids
Resin hybrid laminates

17. What is warpage of laminates?

In laminates which are not symmetric, a temperature difference results in out-
of-plane deformation. This deformation is also called warpage and is calculated
by integrating –displacement equation
∂2w
κx = − 2
∂x
∂2w
κy = − 2
∂y
∂2w
κ xy = −2
∂x∂y

18. What is maximum stress failure theory?

The stresses acting on a lamina are resolved into the normal and shear stresses
in the local axes. Failure is predicted in a lamina, if any of the normal or shear
stresses in the local axes of a lamina are equal to or exceed the corresponding
ultimate strengths of the unidirectional lamina.
Given the stresses or atrains in the global axes of a lamina, one can find the
stresses in the material axes . The lamina is considered to be failed if
- (σ 1c )ult < σ 1 < (σ 1T )ult
- (σ 2c )ult < σ 2 < (σ 2T )ult
or
- (τ 12)ult < τ 12 < (τ 12)ult
19. What is strength ratio?
The strength ratio is defined as
Maximum Load Which Can Be Applied
SR=
Load Applied
The concept of strength ratio is applicable to any failure theory. If SR>1, then
the lamina is safe and the applied stress can be increased by a factor of SR. If
SR<1, the lamina is unsafe and the applied stress needs to be reduced by a
factor of SR. A value of SR=1 implies the failure load.
20. What is ‘failure envelopes’?
A failure envelope is a three dimensional plot of the combinations of the
normal and shear stresses which can be applied to an angle lamina just before
failure. Since drawing three-dimensional graphs can be time consuming, one
may develop failure envelopes for constant shear stress, τxy, and then use the
two normal stresses σx and σy as the two axes. Then if the applied stress is
within the failure envelope, the lamina is safe, otherwise it has failed.

12
Unit 4

1. List down the materials used for sandwich construction.

Face material
Core material
Wood
Foam
Polyvinyl chloride foam(PVC)
Poystyrene foams
Polyurethane foams
Polymethyl methacrylamide foams
Styrene acrylonitrile (SAN) co-polymer foams

2. List down the advantages using a sandwich construction.

Stiffness to weight ratio is high.
Strength to weight ratio is high.
Honeycomb sandwich panels are also used for energy absorption, air
directionanlisation, acoustical and thermal versatility, radio frequency shielding
etc.,
Honeycomb is also used for straightening and directing air flow.

3. What are the three elements in a structural sandwich?

A pair of thin and strong facing.
A thick and light weight core to separate the facings and carry loads from one
facings to the other and
An attachment which is capable of transmitting shear and axial loads to and
from the core.

4. List down the modes of failure in a sandwich structure.

Facing failure
Flexure crushing of core
Local crushing of core
General buckling
Shear crimping
Face wrinkling
Intra-cell buckling (dimpling)

5. What are the different failure modes of sandwich construction?

Facing failure
Transverse shear failure
Flexure crushing of core
Local crushing of core
General buckling
Shear crimping
Face wrinkling
Intra-cell buckling (dimpling)

6. What is meant by sandwich construction?

Two relatively thin, parallel sheets of structural material bonded to and
separated by a relatively thick, light weight core.

13
 7. Define: Shear crimping.
The column buckling caused by the core having too low a shear modulus.

8. Distinguish between face dimpling and face wrinkling.

Face dimpling Face wrinkling

The compressive buckling of the The local compressive instability of
facing in between the honeycomb facing; similar to plate buckling on an
walls caused by thin facings or elastic foundation.
large cell core.
9. What is splicing?
When large core pieces or complex shapes are desired, small pieces can be
spliced together with core splicing adhesives.

10. What is bonding pressure?

Adhesives such as the phenolics and some others actually require more than
atmospheric pressure in order to prevent excessive porosity. Most of the core
materials alone cannot withstand compressive bonding loads exceeding a few
atmospheres and consequently are not fit to be used with any adhesive system
requiring higher bonding pressures.

11. What is fillet forming?

In order to achieve a good attachment to an open cell core, the adhesive must
have a unique combination of surface tension, surface wetting and controlled
flow during early stages of cure. Controlled flow prevents the adhesive from
flowing down the cell wall and leaving a low strength top skin attachment and
an overweight bottom skin attachment.

12. What is adaptability?

In case of contoured parts, the adhesive must also be a good gap-filler without
appreciable strength penalty, since tolerance control of details is much more
difficult to achieve on contoured parts than on flat panels.

13. What is meant by flexure modulus.

The ratio, within the elastic limit, of the applied stress on a test specimen in
flexure to the corresponding strain in the outermost fibers of the specimen.

14. What are the aspects must be considered in designing sandwich structures?
(a)The sandwich is a composite structure.
(b) The material used may be anisotropic
(c) The core has sufficient shear modulus.

15. What is the purpose of the attachment of core with facings?

(a) Act as single unit under deflection.
(b) Prevent separation and relative motion between the components
(c) Have sufficient strength to force failure in either the core or the facings at
only the ultimate load.

14
16. Write short notes on : Polyvinyl chloride
Closed-cell polyvinyl chloride (PVC) foams are one of the most commonly
used core materials for the construction of high Performance sandwich
structures. Although, they are a chemical hybrid of PVC and polyurethane,
they tend to be referred to simply as ‘PVC foams’.

17. What is the needs of design guide lines in sandwich construction?

Requirements of thick facings to withstand the tensile, compressive and shear
stresses induced by the design loads.
Adequate strength of the core to withstand shear stresses induced by the design
loads.
Adequate compressive strength of the core to resist crushing by design loads
acting normal to the panel facings or by compressive stresses induced through
flexure.
Requirements of thick core having sufficient shear modulus to prevent overall
buckling of the sandwich under load.

18. What is the property of toughness?

In the area of sandwich core-to–facing bonds, toughness refers to the resistance
shown by the adhesive towards loads, which act to separate the facings from
core under either static or dynamic conditions. Greater toughness in the bond
line usually equates to greater durability and thus to longer service life.

19. Define: Foam.

The use of foam as a structural core continues to be extensive. Recent
developments in the technology of foam injection have increased the use of
these materials. The most novel of these methods is the use of a cold-cavity
die, in which the foam is injection molded in a single production step. This is
one of the core materials.

20. What are the types of honeycomb?

Paper honeycomb
Aluminium honeycomb
Glass fibre reinforced plastic honeycomb
Aramid paper honeycomb
Carbon fibre honeycomb
Kevlar honeycomb
Kevlar paper honeycomb

15
Unit 5

1. Explain the difference between fibers and whiskers.

Fiber
A fiber is characterised geometrically not only by its very high length to
diameter ratio but by its near crystal sized diameter.
Whiskers
A whisker has essentially the same near-crystal-sized diameter as a fiber but
generally is very short and stubby, although the length-to-diameter ratio can be
in the hundreds. Thus a whisker is an even more obvious example of the crystal
–bulk-material-property-difference paradox.

2. Distinguish between open mould and close mould processes.

Open mould process: It is done in open structure.
• Spray lay up
• Hand lay up
• Filament winding
• SMC
• Expansion tool moulding
• Contact moulding
Closed mould processes
It is done in a closed structure.
• Compression moulding
• Vacuum bag
• Injection moulding
• Resin transfer

3. What is meant by sizing of glass fibers?

The filaments are cooled rapidly and coated with a sizing such as starch,
gelatine, oil etc. to avoid damage to the fibers. The sizing imparts strand
integrity, resin compatibility, adhesion properties, etc. to the final product.

4. What is vacuum bag moulding?

A process in which a lay-up is cured under pressure by drawing a vacuum in
the space between the lay-up and a flexible sheet placed over it and sealed at
the edges.

5. Define: Roving.
Collection of bundles of continuous filaments either as untwisted strands or as
twisted yarns.

6. What is pre-preg?
It is impregnated with resin and partly cured. A combination of mat, fabric or
non-woven material with resin advanced to B-stage, ready for curing.

7. What is meant by knitting?

A method of constructing fabric by interlocking series of loops of one or more
yarns.

16
 8. State the process of injection moulding.
Method of forming a plastic to the designed shape by forcing the heat softened
plastic into a relatively cool cavity under pressure.

9. Give brief notes on: filament winding.

A fabrication process in which continuous filament is treated with resin and
wound onto a removable mandrel in a present pattern.

10. State the definition of fiber glass.

An individual filament made by drawing molten glass. A continuous filament
is a glass fiber of great of indefinite length.

11. What is facing failure?

The sandwich panel failure caused by the facing failing in compression, tension
or local buckling.

12. Explain the term: Facing.

One of the two outer layers, which has been bonded to the core of a sandwich.

13. What is meant by cure?

To change the properties of a thermosetting resin irreversibly by chemical
reaction, i.e., condensation, ring closure, or addition. Cure may be
accomplished by addition of curing (cross-linking) agents, with or without
catalyst, and with or without heat and pressure.

14. Define the term: Creep.

The time dependent part of strain resulting from an applied stress. Also referred
to as the change in dimension of a material under load over a period of time.

15. What is creel?

A framework arranged to hold tows, rovings or yarns so that many ends can be
withdrawn smoothly and evenly without tangling.

16. What is ‘chopped strands’?

Short strands cut from continuous filament strands of reinforcing fibetr, not
held together by any means.

17. What is the function of caul plate?

Smooth metal plates, free of surface defects, same size and shape as that of a
composite lay-up, used immediately in contact with the lay-up during the
curing process to transmit normal pressure and to a smooth surface on the
finished laminate.

18. What are the characteristics of carbon fiber?

Reinforcing fiber known for its light weight, high strength and high stiffness
produced by pyrolysis of an organic precursor fiber in an inert atmosphere at
temperature above 1000ºC. Can also be graphitised by heat-treating above
2500ºC.

17
19. What is the function of bleeder cloth?
A material used to allow the escape of gases and excess resin during cure cycle.
It is removed after completion of curing cycle.

20. What are the desired properties of the matrix?

Reduced moisture absorption.
Low shrinkage.
Low coefficient of thermal expansion.
Good flow characteristics so that it penetrates the fibre bundles completely and
eliminates voids during the compacting/curing process.
Reasonable strength, modulus and elongation (elongation should be greater
than fibre).
Must be elastic to transfer load to fibers.

PartB (16 Marks) Questions with keys

Unit 1
1. Obtain an expression for E1 , E2, and G12 in terms of material properties
with respect to principal material directions using mechanics of material
approach.
Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 159-173.

2.(a) What are the advantages of composite material? And explain its area of
application?
Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 28-45.

(b) Show the reduction of anisotropic material stress-strain equations to those of

a monoclinic material stress-strain equations.
Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 75-77.

3. For a graphite/epoxy unidirectional lamina, find the following.

(a) Compliance matrix.
(b) Minor poisons ratio.
(c) Reduced stiffness matrix.
(d) Strains in the 1-2 co-ordinate system if the applied stresses are σ1=2MPa,
σ2= -3MPa, τ12= 4MPa,
E1=181GPa, E2=10.3 GPa, υ12=0.28,G12=7.17 GPa.
Ans:
 0.0055 − 0.0015 0 

(a) [S]= − 0.0015 0.097 0  x10-9 Pa-1
 0 0 0.1395

18
 (b) υ21 = 0.01593
181.8 2.897 0 

(c) [Q] = 2.897 10.35 0  x109
 0 0 7.17 
µm µm µm
(d) ε1 =15.69 ; ε2 = -294.4 ; γ12 =557.9 .
m m m

4. Explain the Hooke.s law for different materials?

Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 67-69.

5. Explain monoclinic material with compliance and stiffness matrices.

Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 70-72.

Unit 2
1. (a) For glass epoxy laminate Ef = 85 Gpa, Em = 3.4 GPa, υm = 0.3 and υf = 0.25,
find the minor Poisson’s ratio υ21 and G12 for a fiber volume fraction of 70%.
Ans; υ21 =0.23; G12 =0.03939.

(b) What weight of glass fibers must be added to 1kg of epoxy to produce a
composite with a density of 1700 kg/m3, ρf = 2500kg/m3 and ρm =1200 kg/m3.
Ans: Weight of glass fibers = 1.3007kg.

2.(a) Describe stress strain relations for a lamina of arbitrary orientation.

Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 115-116.

(b) A graphite/ epoxy cuboid specimen with voids has dimensions a x b x c and
its mass is Mc. After putting it in a mixture of sulphuric acid and hydrogen
peroxide, the remaining graphite fibers have a mass Mf. From independent
tests, the densities of graphite and epoxy are ρf and ρm, respectively. Find the
volume fraction of the voids in terms of a, b, c, Mf,Mc, ρf and ρm.
v 1 Mf Mc − Mf 
Ans.: Vv = v = 1 −  +
abc abc  ρ f ρ m 

3. Explain the elasticity approach to find four elastic moduli.

Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw p180-183.

4. Explain Hooke.s law for a twodimensional unidirectional lamina?

Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 80-82.

5. Find the following for a 60º angle lamina of graphite /epoxy. E1=181GPa,
E2=10.3GPa, υ12=0.28,G12=7.17 GPa.
(a) Transformed compliance matrix
(b) Transformed reduced stiffness matrix
If the applied stress is σx =2 MPa, σy =-3MPa, τxy = 4MPa, also find
(c) Global strains
(d) Local strains
(e) Local stresses

19
 (f) Principal stresses
(g) Maximum shear stress
(h) Principal strains
Ans:
−− 1
S 12 = −0.7878(10 −11 )
Pa
−− 1
S 16 = −0.3234(10 −10 )
Pa
−− 1
(a) S 22 = 0.3475(10 −10 )
Pa
−− 1
S 26 = −0.4696(10 −10 )
Pa
−− 1
S 66 = 0.1141(10 −9 )
Pa

0.2365 0.3246 0.2005

−−  
(b) Q  = 0.3246 0.1094 0.5419 x1011 Pa
 
0.2005 0.5419 0.3674
 ε x   0.5534(10 −4 ) 
   
(c)  ε y  = − 0.3078(10 −3 )
γ xy   0.5328(10 −3 ) 
   

 ε 1   0.1367(10 ) 
−4

 
(d)  ε 2  = − 0.2662(10 −3 )
γ 12  − 0.5809(10 −3 )

σ 1   0.1714(10 ) 
7

 
(e) σ 2  =  − 0.2714(10 7 ) Pa
 
τ 12   − 0.4165(10 7 ) 

(f) σmax,min = 4.217,-5.217 MPa

(g) τmax = 4.717 MPa.
(h) ε max, min = 1.962(10-4), -4.486(10-4)

Unit 3
1. Explain Tsai-Hill failure theory used for anisotropic materials.
Show that for unidirectional lamina the failure theory can be written as
σ12 / X2 - σ1σ2 / X2 + σ22 / Y2 + τ122 / S2 = 1 where σ1, σ2, τ12 are the stress
components with respect to principal material direction and X, Y and Z are
failure strengths of the lamina.
Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 119-122.

2.(a) What are the types of laminates given below? Mention which elements of

20
 [A],[B] and [D] are zero for each of them.
(1) [ ± 45 / ± 45]
(2) [ 30 / -45 / -30 / 45]
(3) [0 / 90 / 0 / 90]
Ans: (1) Angle ply laminate
(2) Balanced laminate
(3) Cross ply laminate and also
Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 269-271.

(b) Compute [A] matrix for a [0/±45] laminate with the following laminate
properties. E1 =145 GPa, E2 =10.5 GPa, υ12 = 0.28 and G12 =7.5 GPa.
Thickness of each lamina is 0.25 mm.
6.045X10 6 1.728X10 6 0 
 
Ans:  5.55x10 5 2.668x10 7 0 
 0 0 2 . 068 x10 7
 

3. Find the stiffness matrices [A], [B] for a three ply [0/30/-45] graphite epoxy
laminate. Assume each lamina has a thickness of 5mm. The properties of
graphite/epoxy El =181 GPa, Et =10.3 GPa, υlt = 0.28 and Glt =7.17 GPa.

1.739 x10 9 3.88x10 8 5.66 x10 7 

 
Ans: [A] =  3.44 x10 8 4.53x10 8 − 1.14 x10 8  Pa-m.
 5.66 x10 7 − 1.141x10 8 4.525x10 8 

− 3.128x10 6 9.85x10 5 − 1.07 x10 6 
 
[B] =  9.86 x10 5 1.157 x10 6 − 1.07 x10 6  Pa-m.
 − 1.07 x10 6 − 1.07 x10 6 9.85x10 5 


4. A symmetric angle ply laminate hae the following data: 4 Layers of each
0.5mm thick +45º/-45º/-45º/+45º . El =210 GPa, Et =21 GPa, υit = 0.3 and
Git =7 GPa. Compute the in-plane stiffness matrix of the laminate.
Ans: Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 237-23.

5. Derive the governing differential equation for a laminated unidirectional

anisotropic plate.
Ans: Refer ‘Mechanics of composite materials’ by Robert M. Jones pp 290-
299.

Unit 4
1(a) What are the materials used for sandwich construction.
Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 68-76.

(b) Write short notes on the failure modes of sandwich panels.

Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 83.

2. (a) Explain basic design concept of sandwich construction.

Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 81-82.

21
 (b) Explain the two methods of honey comb core manufacturing.
Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 77-78.

3. Explain the cell configuration in honeycomb cores?

Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 78-79.

4. Obtain an expression for the flexural modulus of a

(a) Sandwich plate with different face thickness.
(b) Sandwich plate with different face thickness and material.
Ans:Refer ‘Mechanics of materials approach’ by Autar K.Kaw pp 84-88.

5. Explain the honeycomb processes.

Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 81-82.

Unit 5
1. (a) What are the functions and desirable properties of resins?`
Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 33-34.

(b) Write short notes on vacuum bag moulding and continuous pultrusion.
Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 201-203;215-
217.

2. (a) Explain with neat sketches the production of carbon fibers.

Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 15-18.

(b) What are the commercial forms of fibers?

Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 9-32.

3.(a) Explain open and closed mould processes.

(b) Explain with neat sketches one fabrication process under each method.
Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 189-215.

4. Explain any two methods of glass fiber manufacturing with neat sketch.
Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 11-14.

5. (a) Explain the applications of resins.

Ans: Refer ‘Advanced composite materials’ by Lalit Gupta pp 43-44.

(b) Write short notes on Netting analysis.

Ans: Refer ‘Mechanics of composite materials’ by Robert M. Jones pp 253-
254.

22
23