Scribd
Upload
3K views

Engineering Graphics

This document outlines the syllabus for an Engineering Graphics course. The syllabus covers topics such as introduction to engineering graphics, engineering curves, loci of points, projections of points and lines, projections of planes and solids, development of lateral surfaces, orthographic projections, and isometric projections. Key areas covered include drawing instruments, conic sections, mechanisms, projections with different orientations, sections of solids, parallel and radial line development, first and third angle projections, and isometric views. The syllabus also lists several required and reference textbooks on engineering drawing and graphics.

Uploaded by

varshasadafule
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
3K views

Engineering Graphics

This document outlines the syllabus for an Engineering Graphics course. The syllabus covers topics such as introduction to engineering graphics, engineering curves, loci of points, projections of points and lines, projections of planes and solids, development of lateral surfaces, orthographic projections, and isometric projections. Key areas covered include drawing instruments, conic sections, mechanisms, projections with different orientations, sections of solids, parallel and radial line development, first and third angle projections, and isometric views. The syllabus also lists several required and reference textbooks on engineering drawing and graphics.

Uploaded by

varshasadafule
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Engineering Graphics

1. Introduction to Engineering Graphics, Drawing instruments and accessories, BIS - SP


46. Use of plane scales and Representative Fraction.

2. Engineering Curves: Classification of Engineering Curves, Construction of Conics,


Cycloidal Curves, Involutes and Spirals.

3. Loci of Points: Path of the points moving on simple arrangements and simple
mechanisms, slider crank mechanism, four bar chain mechanism etc.

4. Projections of Points & Lines: Introduction to principal planes of projections, Projections


of the points located in same quadrant and different quadrants, Projections of line with
its inclination to one reference plane and with two reference planes. True length of the
line and its inclination with the reference planes.

5. Projections of Planes: Concept of different planes, Projections of planes with its


inclination to one reference plane and with two reference planes. Concept of auxiliary
plane method for projections of the plane.

6. Projections of Solids & Section of Solids: Classification of solids. Projections of solids


like Cylinder, Cone, Pyramid and Prism with its inclination to one reference plane and
with two reference planes. Section of such solids and the true shape of the section.

7. Development of Lateral Surfaces: Concept of development of the different surfaces.


Parallel Line Development and Radial Line Development.

8. Orthographic Projections: Principle of projection, Principal planes of projection,


Projections from the pictorial view of the object on the principal planes for View from
Front, View from Top and View from Side using first angle projection method and third
angle projection method, Full Sectional View.

9. Isometric Projections and Isometric View or Drawing: Isometric Scale, Conversion of


orthographic views into isometric projection, isometric view or drawing.

NOTE: Topic No. 1, 8 and 9 of the above syllabus to be covered in Practical Hours.

Text Books:
1. A Text Book of Engineering Graphics By P.J.Shah
S.Chand & Company Ltd., New Delhi
2. A Text Book of Machine Drawing By P.J.Shah
S.Chand & Company Ltd., New Delhi
3. Elementary Engineering Drawing By N.D.Bhatt
Charotar Publishing House, Anand
4. Geometrical and Machine Drawing By N.D.Bhatt
Charotar Publishing House, Anand

Gujarat Technological University B.E Sem I 9


Reference Books:

1. Engineering Graphics – I and II By Arunoday Kumar


Tech – Max Publication, Pune
2. Engineering Drawing & Graphics using Auto CAD 2000 By T. Jeyapoovan
Vikas Publishing House Pvt. Ltd., New Delhi
3. A text book of Engineering Drawing By R.K.Dhawan
S.Chand & Company Ltd., New Delhi
4. A text book of Engineering Drawing By P.S.Gill
S.K.Kataria & sons, Delhi
5. Engineering Drawing with an Introduction to AutoCAD By D.A.Jolhe
Tata McGraw-Hill Publishing Co. Ltd., New Delhi
6. Computer Aided Engineering Drawing, S. Trymbaka Murthy
I.K.International Publishing House Pvt. Ltd., New Delhi

Gujarat Technological University B.E Sem I 10

You might also like