0% found this document useful (0 votes)
6K views10 pages

Please Put Home TP: 12316 H 30000: COSHIP (5202 & 5203)

This document provides step-by-step instructions for setting up a Sundirect dish to receive channels from the Measat 3 satellite instead of the previously used Insat 4b satellite. It involves adjusting the dish to the new azimuth and elevation coordinates for Measat 3, editing the transponder settings on the set top box to input the frequencies and parameters for Measat 3 transponders, and then running a channel search to populate the channel list. Key steps include finding the azimuth and elevation online, adjusting the dish position, deleting existing transponder data, inputting 12 transponder frequencies and parameters one by one, selecting all transponders, and running a channel search.
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
6K views10 pages

Please Put Home TP: 12316 H 30000: COSHIP (5202 & 5203)

This document provides step-by-step instructions for setting up a Sundirect dish to receive channels from the Measat 3 satellite instead of the previously used Insat 4b satellite. It involves adjusting the dish to the new azimuth and elevation coordinates for Measat 3, editing the transponder settings on the set top box to input the frequencies and parameters for Measat 3 transponders, and then running a channel search to populate the channel list. Key steps include finding the azimuth and elevation online, adjusting the dish position, deleting existing transponder data, inputting 12 transponder frequencies and parameters one by one, selecting all transponders, and running a channel search.
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 10

Please put Home TP: 12316 H 30000

COSHIP (5202 & 5203):

1. Step 1: Go to Installation menu and select “Advanced Installation” option.


2. Step 2: Select “Insat 4B/SAT “and press OK on the remote & press Yellow color key to
“TP Edit”. (Must to be select satellite No.1)
3. Step 3: Press Right Navigation key on the remote for adding “New Parameters”
4. Step 4: Enter “New Parameters” like “Frequency, Symbol rate, Polarity”
5. Step 5: Fill all “New Parameters” and select OK “Signal strength & Quality “displayed
on screen.
6. Step 6: Press Red color key to “Searching” all available channels.
7. Step 7: After Scanning Press Exit and watch our New channels on “New Satellite”

Home cast (5202 & 5203):

1. Step 1: Go to Menu and select “Installation” option.


2. Step 2: Select “Manual Scan” and press OK on
the remote.
3. Step 3: Pop up window display on the screen “Enter PIN
Code” default password is “0000”
4. Step 4: “Manual Scan setting” menu option below

Dish – Don’t change


Frequency (MHz) – Need Change
Polarity – Need Change
Symbol rate (Msym/s) – Need Change
Modulation – Don’t change
Pilot – Don’t change
Code Rate – Don’t change
Scan Mode – Don’t change
Service Type – Don’t change
Network Search – Don’t change

5. Step 5: Enter the all “New downlink parameters” using Numeric key on the remote.
6. Step 6: In this Menu see the “Signal Status” and “Signal Strength” levels.
7. Step 7: Press “OK” key on the remote for “Search” all channels
8. Step 8: After scanning its shows “Do you want to save changes” select “Yes” and press
Exit.

Note: After satellite Migration don’t do Factory default, if customer did kindly follow the same
Manual
Tuning steps again.
OPENTEC:

1. Step 1: Go to Menu and select “Installation” option.


2. Step 2: Select “Edit TP” and press OK on the remote.
3. Step 3: Press Green color key on the remote for adding “New TP”
4. Step 4: “New TP” pop up window display on the screen with “Frequency, Symbol rate,
Polarity, FEC”
5. Step 5: Fill all “New Parameters” and select OK “Signal strength & Quality “displayed
on top.
6. Step 6: Press Red color key on the remote for “Searching”
7. Step 7: After Scanning Press Exit and watch our New channels on “New Satellite”

Samsung (P1, P2, P3 & G2):

1. Step 1: Go to Menu and select “Advanced Actions” option and press OK.
2. Step 2: Select “Home Transponder Setting” and press OK on the remote.
3. Step 3: Pop up window display on the screen “Enter PIN Code” default password is
“0000”
4. Step 4: “Home Transponder setting” menu option below

Network ID – Don’t change


Frequency (MHz) – Need Change
Symbol rate (Msym/s) – Need Change
LO Low (MHz) – Don’t change
LO High (MHz) – Don’t change
LNB Power – Don’t change
Polarization – Need Change
Position – Don’t change

5. Step 5: Enter the all “New downlink parameters” using Numeric key on the remote.
6. Step 6: Press OK to see the “Signal Status” for new parameters and press exit twice.
7. Step 7: Select “Channel Installation” and its shows “Enter PIN Code” default password is
“0000”
8. Step 8: In this Menu see the “Signal Status” and “Signal Strength” and selected
Parameters details.
9. Step 9: Press “Red color” key on the remote for “Search”
10. Step 10:After scanning its shows “Do you want to save” select “Yes” and press Exit.

Samsung HD:

1. Step 1: Go to Menu and select “System” option.


2. Step 2: Select “Sun Direct TV Manual Scanning” and press “OK” Key on the remote
3. Step 3: “Sun Direct TV Manual Scanning” menu option Listed below

Tuner Don’t change


Satellite Don’t change
Transponder Don’t change
Frequency Need Change
Symbol rate Need Change
FEC Need Change
Polarity Need Change
Modulation Don’t change

4. Step 4: Fill all “New Parameters” and Its shows “Signal status “displayed on same
screen.
5. Step 5: Fill all “New Parameters” and Its shows “Signal status “displayed on same
screen.
6. Step 6: After Scanning its shows “ Search result windows” and press “OK” to confirm.
7. Step 7: Press “Exit” and watch our New channels on “New Satellite”.

So enjoy Sun Direct Viewing now and do change according to your STB model.

Setting up sundirect for measat 3. Do it Yourself


Do it yourself satellite change of sundirect
After waiting for a long time and repeated unsuccessful  contact with customer care and dealer,
finally I decided to change the Dish direction and satellite settings for sun direct myself. here is the
step by step procedure to change and setup sun direct for new satellite measat 3

Initial Preperation

first Visit the site http://www.lyngsat.com/mea3.html for finding out the required azimuth and
elevation for your dish in your location. screen shot of the site is given here, check for the marked
area. Azimuth is the direction clock wise from North (90 deg is East, 180 deg is South, 270 deg is
West, 0 or 360 deg is North) and elevation is movement in vertical plane (0 deg LNB is parallel to
ground and 90 deg is LNB pointing upward). For major cities azimuth and elevation could be
obtained from http://measat.com/support_customer_azimuth.html
What is Azimuth and Elevation

Find azimuth and elevation for your place, it will calculate your location as per your IP
address

It would be better to check azimuth and elevation for Insat 4b at http://www.lyngsat.com/in4b.html,


from where sun direct moved to Measat 3. Now you can see the difference in azimuth and elevation
for both satellite. Normally difference in azimuth is 3.3 degree Clock wise and 2 degree up for
elevation

Before adjusting the satellite, first switch on the TV and set top box , press menu and go to
insatallation. (This metod is almost same for all set top boxes, here I am using Coship)
Menu setup page

Advanced setup page

1. Select advanced installation using left and down key of remote.

2. Select first satellite and rename it by pressing the blue button on remote (optional)
3. Press yellow button on remote for TP edit

4. Delete all transponders in the list using blue button (optional)

5.Enter frequency as 12316, symbol rate 30000 and polarity horizontal. If now you are getting quality
above 20 you will be able to receive channels without dish adjustment. if quality is zero or less than
20%, Keep the TV and set top box on and ask some one to watch the screen for 'quality bar'.

( I recommend you to put a mark awith paint or marker on the dish as shown below for
reverting back, if you are not succeeding in aligning to measat 3)

6. Change the direction of the Dish as per the parameters described in First section. As a thumb of
rule just loosen the Nuts under the dish a little and move the Dish direction 3 degrees clock wise
(just 1- 2 Cms away from North). Lift the dish (tip of LNB) up by 2 degree again around 2 cm
movement. Mean while your attender should be monitoring the quality bar and if there is any
movement adjust the dish for best quality. You should get quality more than 70 % and you may get
upto 87% ( Even though you may receive channels for quality as less as 20 %, try for above
50%.Better the quality better the video and audio)
Transponder (TP) editing page

7. Tighten the nuts where the quality is maximum.

8. get down from the roof, (you had done a wonderful job). take the remote press green button to
add the TP. The data we entered has been updated and you get a new entry for editing. Keep on
entering all the following data's one by one. That is enter the frequency, symbol rate and polarization
one by one, pressing green button after entering each set.

9. make sure after entering polarization you should get some signal strength in quality bar. If you are
not getting any quality percentage, try changing polarity or symbol rate (standard symbol rates for
measat sun direct are 30000, 27500, 19500 and 20000)

Transponder data for feeding


1. Enter this data first, if you have not followed the step above frequency 12316, symbol rate 30000,
polarity Horizontal. press green button to add next transponder.

2. Now enter the following data one by one. keep pressing green button after entering every data set
for saving it.

         Frequency - Symbol rate - Polarity

         12436 - 30000 - Horizontal

         12597 - 19500 - Horizontal

         12615 - 10000 - Horizontal

         12643 - 30000 - Horizontal


         12434 - 30000 - Horizontal

         12523 - 27500 - Vertical

         12563 - 27500 - Vertical

         12603 - 27500 - Vertical

         12643 - 27500 - Vertical

         12723 - 27500 - Horizontal

         12683 - 27500 - Horizontal

For all vertical transponders feed it again in horizontal with symbol rate 30000

If any of the transponder shown above is not showing any quality strength, try changing symbol rate
to 20000 or 30000

Final Setup
Now after entering all data press exit once to get out of data feeding page.

select all transponders one by one and press ok on remote (centre button), a tick mark will appear
next to transponder. Then press red button on remote to search.

You will get a list of channels. press exit togo back. Set top box will restart if not try upgrading
software menu, or switch off and switch on set top box. Set top box will automatically update the
software, which will take around 5 - 10 minutes.

Now click menu, select installation and press ok

you will see signal and quality bars, press red button for starting scan. save and exit

Congratulation now you are done.

In case any thing gone wrong or you are not successful and lost whatever you were getting, Don't
panic. Simply select factory restore. Then go to installation and scan
PENTECH OFS 7100CIR - Sun Direct problem
OPENTEC:
Step 1: Go to Menu and select “Installation” option.
Step 2: Select “Edit TP” and press OK on the remote.
Step 3: Press Green color key on the remote for adding “New TP”
Step 4: “New TP” pop up window display on the screen with “Frequency, Symbol rate, Polarity,
FEC”
Step 5: Fill all “New Parameters” and select OK “Signal strength & Quality “displayed on top.
Step 6: Press Red color key on the remote for “Searching”
Step 7: After Scanning Press Exit and watch our New channels on “New Satellite”

What I Did?

Finally I found solution for OFS 1700CIR set top box of Sun direct.
These steps is for those who having ofs 1700CIR set top box with out green button enabled.
If any one know how to get green button please inform me.
1. first keep dish in existing insat 4B position i.e 93.5deg.
2. make set top box to factory settings.
3. While set to factory settings, it will prompt to press red button for search. press it.
You will get old channels.(You can update software , but for me its failed so the following steps)
4. Now go to Menu->channel search-> then confirm that Network search is on. if not then
change to on, LNB frequency as 9750/10700 , search type auto, and then press red button to
initiate search.. the settings will be saved.
5. Search for channels. then save.
6. you can see symbol rates 30000 and some transponders/ settings are added after doing above
steps.(if not added then set lnb frequency as 9750/10600 and try)
7. Allign the dish to new satellite measat positon.
8. Go to channel search , set lnb to 9750/10700.
9. Search by pressing red button.
10. when search is over new channels are added . go to channel 984 to see the new satellite
promotional channel.
11. for normal coship, and other set top boxes the software will upgrade automatically. but for
this ofs 1700cir box. it won't presently.
12. You can see sun channels also in channel number with four digits, 1001 and so.
13. check channel 556, if you are getting NDTV if yes every thing is fine. some times the
channel number may vary, in such case check symbol rate 30000, for new satellite sun dth
channel. if you are receiving then every thing is fine. you should wait for some time ,may be
months, so that your set top box to updates software. till you can enjoy all channels, including
ten sports for free.
sorry for my english.

Present problem:

Not able to view channels with LNB frequency range 9750/10600.


12316/sr30000/H ,12597 channels.
In this case I can view all v channels like doodarshan, vasanth tv, shalom tv and so on.
Since i didn't do factory defaults in measat position exisiting channels number are present. So i
can't specify exact channel numbers. i am getting sun promotional channels.

But when the LNB frequency is set us 9750/10750,


then we can view sun channels at frequency 12402/sr30000.

I need to know, what this factor.


what is the LNB frequecy range for SUN Direct.
How can I get channel with frequency 12316/30000/H
What shall i o for that?
Any LNB re alignment or dish alignment.

You might also like