Preface

Copyright
This publication, including all photographs, illustrations and software, is protected un-
der international copyright laws, with all rights reserved. Neither this manual, nor any
of the material contained herein, may be reproduced without written consent of the au-
thor.

Version 7.3

Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any par-
ticular purpose. The manufacturer reserves the right to revise this publication and to
make changes from time to time in the content hereof without obligation of the manu-
facturer to notify any person of such revision or changes.

Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners
and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not oc-
cur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
− Reorient or relocate the receiving antenna.
− Increase the separation between the equipment and the receiver.
− Connect the equipment onto an outlet on a circuit different from that to which
the receiver is connected.
− Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly approved by the system's manu-
facturer could void the user's authority to operate the equipment.

i
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the follow-
ing conditions:
− This device may not cause harmful interference, and
− This device must accept any interference received, including interference
that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-
causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1 Describes features of the mainboard,

and provides a shipping checklist.
Introducing the Mainboard
Go to ⇒ page 1

Chapter 2 Describes installation of mainboard

components.
Installing the Mainboard
Go to ⇒ page 7

Chapter 3 Provides information on using the BIOS

Setup Utility.
Using BIOS
Go to ⇒ page 21

Chapter 4 Describes the mainboard software.

Go to ⇒ page 32
Using the Mainboard Software

ii
TABLE OF CONTENTS
Preface i

CHAPTER 1 1
Introducing the Mainboard 1
Introduction .................................................................................................1
Checklist .....................................................................................................1
Standard Items ................................................................................................. 1
Features .....................................................................................................1
Choosing a Computer Case .......................................................................4
Mainboard Components .............................................................................5

CHAPTER 2 7
Installing the Mainboard 7
Mainboard Installation.................................................................................7
Installing the Processor ..............................................................................8
Installing Memory Modules .........................................................................9
Checking Jumper Settings ........................................................................11
Connecting Case Components .................................................................13
The Panel Connectors.................................................................................... 14
Floppy Diskette Drive Installation................................................................. 15
IDE Devices .................................................................................................. 15
Installing Add-on Cards................................................................................. 16
Connecting Optional Devices ........................................................................ 17
Connecting I/O Devices ............................................................................19
External Connector Color Coding ................................................................. 20

CHAPTER 3 21
Using BIOS 21
About the Setup Utility ..............................................................................21
The Standard Configuration .......................................................................... 21
Entering the Setup Utility .............................................................................. 22
Using BIOS ...............................................................................................22
Standard CMOS Features .............................................................................. 23
Advanced Setup Page .................................................................................... 24
Power Management Setup Page .................................................................... 26
PCI / Plug and Play Setup Page..................................................................... 27
Load Optimal Settings ................................................................................... 28
Load Best Performance Settings.................................................................... 28
Features Setup Page....................................................................................... 28
CPU PnP Setup Page ..................................................................................... 30
Hardware Monitor Page................................................................................. 30

iii
CHAPTER 4 31
Using the Mainboard Software 32
About the Software CD-ROM ...................................................................32
Auto-installing under Windows 98/ME/2000/XP .......................................32
Running Setup ............................................................................................... 33
Manual Installation....................................................................................35
Utility Software Reference ........................................................................35

iv
 Chapter 1
Introducing the Mainboard

Introduction
Thank you for choosing the P4VMM2 mainboard. This mainboard has a
Socket 478 for the Intel Pentium 4 type of processors supporting front side
bus (FSB) speeds up to 533/400 MHz.
This mainboard incorporates the VIA P4M266/A Northbridge and VT8235
Southbridge chipsets that support AC 97 audio codec, and provide Ultra DMA
133/100/66/33 function. It supports built-in USB 2.0 providing higher band-
width. It implements Universal Serial Bus Specification Revision 2.0 and is
compliant with UHCI 1.1 and EHCI 0.95. This mainboard has two 32-bit PCI
slots, one 4xAGP slot, one CNR (Communications and Networking Riser) slot,
and an onboard 10BaseT/100BaseTX Network interface (optional). In addition,
this mainboard has a full set of I/O ports including two PS/2 ports for mouse
and keyboard, one serial port, one VGA port, one parallel port and six USB2.0
ports– four back-panel ports and onboard USB header USB2 providing two
extra ports by connecting the Extended USB Module to the mainboard.
This mainboard is a Micro ATX size mainboard and has power connectors for
an ATX power supply.

Checklist
Compare the mainboard’s package contents with the following checklist:

Standard Items
• One mainboard
• One diskette drive ribbon cable
• One IDE drive ribbon cable
• Retention Module
• Software support CD
• This user’s manual

Features
1
Processor The P4VMM2 mainboard uses a mPGA478 Socket that has
the following features:
• Accommodates Intel Pentium 4 478-pins CPU
• Supports a front-side bus (FSB) of 400/533 MHz
Chipset The P4M266/A Northbridge and VT8235 Southbridge in this
chipset in accordance with an innovative and scalable archi-
tecture with proven reliability and performance. A few of the
chipset’s advanced features are:
• An advanced V-Link memory controller architecture that
provides the bandwidth up to 533 MB/s and performance
necessary for even the most demanding Internet and 3D
graphics
• Support for an 4xAGP interface providing vivid 3D graph-
ics and video performance
• An ATA 133 interface on the chipset, which helps boost
system performance by providing a high-speed connec-
tion to ATA 133 Hard Disk Drives, delivering maximum
sustained data transfer rates of 133 MB/sec
Additional key features include support for six USB ports, an
AC 97 link for audio and modem, hardware monitoring, and
ACPI/OnNow power management.
Memory • The mainboard accommodates two 184-pin, 2.5V DDR
DIMM sockets with a total capacity of 2 GB system mem-
ory
• Supports DDR up to 200/266MHz memory bus
Built-in Graphics • P4M266/A integrates S3’s Savag4 graphics accelera-
System tor into a single chip. P4M266/A brings mainstream
graphics performance to the Value PC with leading-edge
2D, 3D and DVD video acceleration into a cost effective
package. Based on its capabilities, P4M266/A is an ideal
solution for the consumer, corporate mobile users and en-
try-level professionals
• Maximum-shared memory size is 32 MB
Graphics This mainboard includes an AGP slot that provides four times
the bandwidth of the original AGP specification. AGP technol-
ogy provides a direct connection between the graphics sub-
system and memory so that the graphics do not have to com-
pete for processor time with other devices on the PCI bus.
AC’97 Audio • Compliant with AC’97 2.1 specification
Codec • 16-bit stereo full-duplex CODEC with fixed 48KHz sam-
pling rate
• 3 analog line-level stereo inputs with 5-bit volume control:
LINE-IN, CD-IN, AUX-IN
• 1 analog line-level mono input: PHONE-IN
• Three Audio Jacks – Line-Out, Line-In and Microphone-In
• Sound Blaster, Sound Blaster Pro Compatible
• Digital I/O compatible with consumer mode S/PDIF
• Advanced power management support

Expansion The mainboard comes with the following expansion options:

Options • Two 32-bit PCI slots capable of Ultra DMA bus mastering

2
 with transfer rates of 33/66/100/133 MB/sec
• An AGP slot
• One CNR (Communications and Networking Riser) slot
Integrated I/O The mainboard has a full set of I/O ports and connectors:
• Two PS/2 ports for mouse and keyboard
• One serial port
• One VGA port
• One parallel port
• Six USB2.0 ports (four back-panel ports, onboard USB
header providing two extra ports)
• Audio jacks for microphone, line-in and line-out
USB 2.0 • Compliant with Universal Serial Bus Specification Revi-
sion 2.0
• Compliant with Intel’s Enhanced Host Controller
Interface Specification Revision 0.95
• Compliant with Universal Host Controller Interface
Specification Revision 1.1
• PCI multi-function device consists of two UHCI Host
Controller cores for full-/low-speed signaling and one
EHCI Host Controller core for high-speed signaling
• Root hub consists 4 downstream facing ports with
integrated physical layer transceivers shared by UHCI
and EHCI Host Controller
• Support PCI-Bus Power Management Interface
Specification release 1.1
• Legacy support for all downstream facing ports
Built-in Ethernet • 100Base-TX/10Base-T Physical Layer Solution
LAN (optional) • Dual Speed – 100/10 Mbps
• MII Interface to Ethernet Controller/Configuration & Status
• Auto Negotiation: 10/100, Full/Half Duplex
• Meet All Applicable IEEE802.3, 10Base-T and 100Base-
TX Standards
BIOS Firmware This mainboard uses AMI BIOS that enables users to config-
ure many system features including the following:
• Power management
• Wake-up alarms
• CPU parameters and memory timing
• CPU and memory timing
The firmware can also be used to set parameters for different
processor clock speeds.

Some hardware specifications and software items are subject to change

without prior notice.

3
Choosing a Computer Case
There are many types of computer cases on the market. The mainboard com-
plies with the specifications for the Micro-ATX system case. Some features on
the mainboard are implemented by cabling connectors on the mainboard to
indicators and switches on the system case. Ensure that your case supports
all the features required. The mainboard can support one or two floppy disk-
ette drives and four enhanced IDE drives. Ensure that your case has sufficient
power and space for all the drives that you intend to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that
the I/O template in the case matches the I/O ports installed on the rear edge
of the mainboard.
This mainboard has a Micro-ATX form factor of 244 mm x 200 mm. Choose a
case that accommodates this form factor.

4
Mainboard Components

5
Table of Mainboard Components
Label Component
AGP1 Accelerated Graphics Port
BAT1 Three volt realtime clock battery
CD1 Primary CD-in connector
CD2 Secondary CD-in connector
CN5 Standard power connector
CNR1 Communications Networking Riser slot
CPU SOCKET Micro PGA 478-pin socket for Pentium 4 CPUs
CPU_FAN Cooling fan for CPU
DDR1 ~ DDR2 Two 184-pin DDR memory modules
FDC Floppy disk drive connector
IDE 1 Primary IDE channel
IDE 2 Secondary IDE channel
J1 USB Card Reader Voltage Selector (VCC)
J16 Onboard LAN LED connector
JBAT1 Clear CMOS jumper
JP1A1/JP1B1 CPU Clock jumper
JP2 Keyboard Power On jumper
JUSBC USB Card Reader Connector
PANEL1 Connector for headphone or microphone jack front panel
PANEL2 Connector for case front panel switches and LED indicators
PCI1 ~ PCI2 Two 32-bit add-on card slots
PJ1 Auxiliary power connector for Pentium 4 CPUs
SIR1 Serial Infrared cable header
SPK1 Internal speaker connector
SYSTEM_FAN System fan connector
USB2 Front Panel USB headers

This concludes Chapter 1. The next chapter explains how to install the main-
board.

6
 Chapter 2
Installing the Mainboard

Mainboard Installation
To install this mainboard in a system, please follow these instructions in this
chapter:
• Identify the mainboard components
• Install a CPU
• Install one or more system memory modules
• Make sure all jumpers and switches are set correctly
• Install this mainboard in a system chassis (case)
• Connect any extension brackets or cables to connecting headers on
the mainboard
• Install other devices and make the appropriate connections to the
mainboard connecting headers.
Note:

1. Before installing this mainboard, make sure jumper JBAT1 is under Nor-
mal setting. See this chapter for information about locating JBAT1 and the
setting options.

2. Never connect power to the system during installation; otherwise, it may

damage the mainboard.

7
Installing the Processor
This mainboard has a Socket 478 processor socket. When choosing a proc-
essor, consider the performance requirements of the system. Performance is
based on the processor design, the clock speed and system bus frequency of
the processor, and the quantity of internal cache memory and external cache
memory.

CPU Installation Procedure

Follow these instructions to install the Retention Module and CPU:
1. Remove the existing retention module (if applicable).

2. Position the backplate

against the underside of
the mainboard, secure
the 4 screws firmly on
the retention module.
Note: Do not over tighten
the screws.

3. Install your CPU. Pull up

the lever away from the
socket and lift up to 90-
degree angle.

4. Locate the CPU cut

edge (the corner with the
pinhole noticeably miss-
ing). Align and insert the
CPU correctly.

5. Press the lever down.

8
6. Apply thermal grease on top of the CPU.

7. Put the CPU Fan down

on the retention module
and snap the four reten-
tion legs of the cooling
fan into place.

8. Flip the levers over to lock the heat sink in place.

9. Connect the CPU Cool-

ing Fan power cable to
the CPUFAN1 connec-
tor. This completes the
installation.

Notes: • To achieve better airflow rates and heat dissipation, we suggest that
you use a high quality fan with 4800 rpm at least.
• CPU fan and heatsink installation procedures may vary with the type of
CPU fan/heatsink supplied. The form and size of fan/heatsink may also
vary.

Installing Memory Modules

This mainboard accommodates two 184-pin 2.5V unbuffered Double Data
Rate SDRAM (DDR SDRAM) Dual Inline Memory Module (DIMM) sockets,
and supports up to 2.0 GB of 200/266 MHz DDR SDRAM.
DDR SDRAM is a type of SDRAM that supports data transfers on both edges
of each clock cycle (the rising and falling edges), effectively doubling the
memory chip’s data throughput. DDR DIMMs can synchronously work with
100 MHz or 133 MHz memory bus.
DDR SDRAM provides 1.6 GB/s or 2.1 GB/s data transfer rate depending on
whether the bus is 100 MHz or 133 MHz. DDR SDRAM uses additional power
and ground lines and requires 184-pin 2.5V unbuffered DIMM module.
Do not remove any memory module from its antistatic packaging until
you are ready to install it on the mainboard. Handle the modules only by
their edges. Do not touch the components or metal parts. Always wear
a grounding strap when you handle the modules.

9
Installation Procedure
Refer to the following to install the memory modules.
1. This mainboard supports unbuffered DDR SDRAM only. Do not attempt to
insert any other type of DDR SDRAM into the slots.

2. Push the latches on each side of the DIMM slot down.

3. Align the memory module with

the slot. The DIMM slots are
keyed with notches and the
DIMMs are keyed with cutouts
so that they can only be in-
stalled correctly.

4. Check that the cutouts on the

DIMM module edge connector
match the notches in the
DIMM slot.

5. Install the DIMM module into

the slot and press it firmly
down until it seats correctly.
The slot latches are levered
upwards and latch on to the
edges of the DIMM.
6. Install any remaining DIMM modules.

10
Checking Jumper Settings
Use the mainboard jumpers to set system configuration options. Jumpers with
more than one pin are numbered. When setting the jumpers, ensure that the
jumper caps are placed on the correct pins.
The illustrations below show a 2-pin jumper. This illustration shows a 3-pin
When the jumper cap is placed on both pins, jumper. Pins 1 and 2 are SHORT.
the jumper is SHORT. If you remove the
jumper cap, or place the jumper cap on just
one pin, the jumper is OPEN.

1 2
Short Open 3

Setting Jumpers
The following illustration shows the location of the mainboard jumpers. Pin 1 is
labeled.

11
JBAT1: Clear CMOS Jumper
This jumper is to clear the contents of CMOS memory. You may need to clear
the CMOS memory if the settings in the Setup Utility are incorrect that pre-
vents your mainboard from operating. To clear the CMOS memory, disconnect
all the power cables from the mainboard and then move the jumper cap into
the CLEAR setting for a few seconds.
Function Jumper Setting
Normal Short Pins 1-2
Clear CMOS Short Pins 2-3
JP1A1, JP1B1: CPU Clock
This jumper enables to select CPU frequency.
CPU Clock JP1A1 JP1B1
100M Short Pins 1-2 Short Pins 2-3
133M Short Pins 2-3 Short Pins 1-2
JP2: Keyboard Power On
This jumper enables any keyboard activity to power up a system previously in
a standby or sleep state.
Function Jumper Setting
5V Short Pins 1-2
5VSB Short Pins 2-3
J1: USB Card Reader Voltage Selector (VCC)
This jumper enables to select voltage of the USB Card Reader.
Function Jumper Setting
5V Short Pins 1-2
5VSB Short Pins 2-3

12
Connecting Case Components
After you have installed the mainboard into a case, you can begin connecting
the mainboard components. Refer to the following:
1. Connect the Pentium
4 processor auxiliary
case power supply
connector to PJ1.
2. Connect the standard
power supply connec-
tor to CN5.
3. Connect the CPU
cooling fan cable to
CPU_FAN.
4. Connect the case
cooling fan connector
to SYSTEM_FAN.
5. Connect the case
speaker cable to
SPK1.
6. Connect the case
LAN LED cable to
J16.
7. Connect the case
switches and indicator
to PANEL1/PANEL2.

PJ1: ATX 12V Power Connector

Pin Signal Name

1 +12V
2 +12V
3 Ground
4 Ground

CN5: ATX 20-pin Power Connector

Pin Signal Name Pin Signal Name

1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 Ground 13 Ground
4 +5V 14 PS ON#
5 Ground 15 Ground
6 +5V 16 Ground
7 Ground 17 Ground
8 PWRGD 18 +5V
9 +5VSB 19 +5V
10 +12V 20 +5V

13
CPU_FAN1/SYSTEM_FAN: FAN Power Connectors

Pin Signal Name Function

1 GND System Ground
2 +12V Power +12V
3 Sense Sensor

SPK1: Internal speaker

Pin Signal Name

1 SPKR
2 NC
3 GND
4 +5V

The Panel Connectors

PANEL1
If there is a headphone jack or a microphone jack on the front panel, connect
the cables to the PANEL1 on the mainboard.
10 9

Pin Signal Name Pin Signal Name

1 MIC IN 2 GND
3 VCCMIC 4 +5V AUDIO
5 LINE OUT (R) 6 LINE OUT (R)
7 NC 8 EMPTY
9 LINE OUT (L) 10 LINE OUT (L)

2 1

PANEL2
This panel connector provides a set of switch and LED connectors found on
ATX case. Refer to the table below for information.
10 9
Empty N/C
(Pin 10) (Pin 9)
Pin Signal Name Pin Signal Name
+1 HDD LED +2 SPD-LED Indicator Reset Switch
Power Switch
(Pins 5, 7)
-3 HDD LED 4 SPD-LED Indicator (Pins 6, 8)

5 Reset Switch 6 POWER ON/OFF

7 Reset Switch 8 POWER ON/OFF
SPD- LED HDD LED
9 NC 10 EMPTY (Pins 2, 4) (Pins 1, 3)

2 1

14
J16: LAN LED Indicator
This connector is attached to LAN device that needs a LED indicator.
Device Pins
Link LED 1, +2 1 LINK LED
ACT LED +3, 4
+

4 ACT LED

Note: The plus sign (+) indicates a pin which must be connected to a positive
voltage.

Floppy Diskette Drive Installation

The mainboard has a floppy diskette drive (FDD) interface and ships with a
diskette drive ribbon cable that supports one or two floppy diskette drives. You
can install a 5.25-inch drive and a 3.5-inch drive with various capacities. The
floppy diskette drive cable has one type of connector for a 5.25-inch drive and
another type of connector for a 3.5-inch drive.

IDE Devices
Your mainboard has a primary and secondary IDE channel interface (IDE1
and IDE2). An IDE ribbon cable supporting two IDE devices is bundled with
the mainboard.
If you want to install more than two IDE devices, get a second IDE cable and
you can add two more devices to the secondary IDE channel.
IDE devices have jumpers or switches to set the IDE device as MASTER or
SLAVE. When installing two IDE devices on one cable, ensure that one device
is set to MASTER and the other one to SLAVE.
This mainboard supports Ultra DMA 66/100/133. UDMA is a technology to
accelerate devices’ performance in the IDE channel. To maximize perform-
ance, install IDE devices that support UDMA and use 80-pin IDE cables
supporting UDMA 66/100/133.

About UltraDMA
This mainboard supports UltraDMA 66/100/133. UDMA is a technology that
accelerates the performance of devices in the IDE channel. To maximize per-
formance, install IDE devices that support UDMA and use 80-pin IDE cables
that support UDMA 66/100133.

15
Installing Add-on Cards
The slots in this mainboard are designed to hold expansion cards and connect
them to the system bus. Expansion slots are a means of adding or enhancing
the mainboard’s features and capabilities. With these efficient facilities, you
can increase the mainboard’s capabilities by adding hardware which performs
tasks that are not part of the basic system.

PCI Slots PCI slots are used to install expansion cards that have the 32-bit
PCI interface.
AGP Slot The AGP slot is used to install a graphics adapter that supports the
4xAGP specification and has a 4xAGP edge connector.

Note: The above layout is for reference only. The AGP slot
may be different from your mainboard. Please refer to
actual shipment.
CNR Slot This slot is used to insert CNR cards with Modem and Audio func-
tionality.

Note: Before installing an add-on card, check the documentation for the card
carefully. If the card is not Plug and Play, you may have to manually con-
figure the card before installation.

Follow these instructions to install an add-on card:

1. Remove a blanking plate from the system case corresponding to the slot
you are going to use.
2. Install the edge connector of the add-on card into the expansion slot. En-
sure that the edge connector is correctly seated in the slot.
3. Secure the metal bracket of the card to the system case with a screw.
Note: For some add-on cards, for example graphics adapters and network adapters,
you have to install drivers and software before you can begin using the add-on
card.

16
Connecting Optional Devices
Refer to the following for information on connecting the mainboard’s optional
devices:

USB2: Front panel USB ports

The mainboard has USB ports installed on the rear edge I/O port array. Addi-
tionally, some computer cases have USB ports at the front of the case. If you
have this kind of case, use auxiliary USB connectors USB2 to connect the
front-mounted ports to the mainboard.
Pin Signal Name Function
1 VREG_FP_USBPWR0 Front Panel USB Power
2 VREG_FP_USBPWR0 Front Panel USB Power
3 USB_FP_P0- USB Port 0 Negative Signal
4 USB_FP_P1- USB Port 1 Negative Signal
5 USB_FP_P0+ USB Port 0 Positive Signal
6 USB_FP_P1+ USB Port 1 Positive Signal
7 GND Ground
8 GND Ground
9 KEY No pin
10 USB_FP_OC0 Overcurrent signal

Note: Please make sure that the USB cable has the same pin assignment as indi-
cated above. A different pin assignment may cause damage or system
hang-up.

17
SIR1: Serial infrared port
The mainboard supports a Serial Infrared (IR1) data port. Infrared ports allow
the wireless exchange of information between your computer and similarly
equipped devices such as printers, laptops, Personal Digital Assistants
(PDAs), and other computers.
Pin Signal Name Function
1 Not assigned Not assigned
2 KEY No pin
3 +5V IR Power
4 GND Ground
5 IRTX IrDA serial output
6 IRRX IrDA serial input

JUSBC: USB Card Reader Connector

This connector is for connecting internal USB card reader. You can use a card
reader to read or transfer files and digital images to your computer.
Pin Signal Name
1 VCC
2 USB-
3 USB+
4 GND
5 KEY

Note: The JUSBC is shared with one of the USB ports of the I/O back
panel. The USB port is located beside the serial port connectors.
See “I/O Ports” for more information.

Please check the pin assignment of the cable and the USB header on
the mainboard. Make sure the pin assignment will match before plug-
ging in. Any incorrect usage may cause unexpected damage to the
system.

18
CD1/CD2: CD-ROM/DVD Audio Input Connector
If you have installed a CD-ROM drive or DVD-ROM drive, you can connect
the drive audio cable to the onboard sound system.
On the mainboard, locate the two 4-pin connectors CD1 and CD2.
There are two kinds of connector because different brands of CD-ROM drive
have different kinds of audio cable connectors. Connect the cable to the ap-
propriate connector.
CD1 CD2
Pin Signal Name Pin Signal Name
1 GND 1 CD IN L
2 CD IN L 2 GND
3 GND 3 GND
4 CD IN R 4 CD IN R

Connecting I/O Devices

The backplane of the mainboard has the following I/O ports:

PS/2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.
PS/2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.
LPT1 Use LPT1 to connect printers or other parallel communica-
tions devices.
COM1 Port Use the COM ports to connect serial devices such as mice or
fax/modems. COM1 is identified by the system as COM1.
VGA Port Use the VGA port to connect VGA devices.
Audio Ports Use the three audio ports to connect audio devices. The first
jack is for stereo line-in signal. The second jack is for stereo
line-out signal. The third jack is for microphone.
LAN Port (optional) Connect an RJ-45 jack to the LAN port to connect your com-
puter to the Network.
USB Ports Use the USB ports to connect USB devices.
Note: The lower USB port located beside the VGA
port is shared with the JUSBC connector.

19
External Connector Color Coding
Many connectors now use standard colors as shown in the table below.
Connector Color
Audio line-in Light blue
Audio line-out Lime
Digital monitor/flat panel White
Microphone Pink
MIDI/game Gold
Parallel Burgundy
PS/2-compatible keyboard Purple
PS/2-compatible mouse Green
Serial Teal or Turquoise
Speaker out/subwoofer Orange
Right-to-left speaker Brown
USB Black
SCSI, network, telephone, modem None

This concludes Chapter 2. The next chapter covers the BIOS.

20
 Chapter 3
Using BIOS

About the Setup Utility

The computer uses the latest AMI BIOS with support for Windows Plug and
Play. The CMOS chip on the mainboard contains the ROM setup instructions
for configuring the mainboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system's
configuration status and provides you with options to set system parameters.
The parameters are stored in battery-backed-up CMOS RAM that saves this
information when the power is turned off. When the system is turned back on,
the system is configured with the values you stored in CMOS.
The BIOS Setup Utility enables you to configure:
• Hard drives, diskette drives, and peripherals
• Video display type and display options
• Password protection from unauthorized use
• Power management features
The settings made in the Setup Utility affect how the computer performs. Be-
fore using the Setup Utility, ensure that you understand the Setup Utility
options.
This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However,
we recommend that you read this chapter in case you need to make any
changes in the future.
This Setup Utility should be used:
• when changing the system configuration
• when a configuration error is detected and you are prompted to
make changes to the Setup Utility
• when trying to resolve IRQ conflicts
• when making changes to the Power Management configuration
• when changing the password or making other changes to the Secu-
rity Setup

21
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST)
routines. POST is a series of built-in diagnostics performed by the BIOS. After
the POST routines are completed, the following message appears:
Press DEL to enter SETUP
Pressing the delete key accesses the BIOS Setup Utility:
AMIBIOS SIMPLE SETUP UTILITY – VERSION 1.21.06
©2000 American Megatrends, Inc. All Rights Reserved
Standard CMOS Setup Features Setup
Advanced Setup CPU PnP Setup
Power Management Setup Hardware Monitor
PCI / Plug and Play Setup Change Password
Load Optimal Settings Exit
Load Best Performance Settings
Esc : Quit ↑ ↓ ← →: Select Item (Shift)F2 : Change Color F5 : Old Values
F6 : Optimal values F7 : Best performance values F10 : Save&Exit

Standards COMOS setup for changing time, date, hard disk type, etc.

BIOS Navigation Keys

The BIOS navigation keys are listed below:
Key Function
Esc Exits the current menu
←↑↓→ Scrolls through the items on a menu
+/–/PU/PD Modifies the selected field's values
F10 Saves the current configuration and exits setup
F1 Displays a screen that describes all key functions
F5 Loads previously saved values to CMOS
F6 Loads a minimum configuration for troubleshooting.
F7 Loads an optimum set of values for peak performance

Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of
the Setup Utility displays a list of the options that are available. A highlight
indicates which option is currently selected. Use the cursor arrow keys to
move the highlight to other options. When an option is highlighted, execute
the option by pressing <Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you
wish to execute that option. Other options lead to dialog boxes that prompt
you for information.

22
Some options (marked with a triangle ) lead to submenus that enable you
to change the values for the option. Use the cursor arrow keys to scroll
through the items in the submenu.
In this manual, default values are enclosed in parenthesis. Submenu items
are denoted by a triangle .

Standard CMOS Features

This option displays basic information about your system.
AMIBIOS SETUP – STANDARD CMOS SETUP
©2000 American Megatrends, Inc. All Rights Reserved
Date (mm/dd/yy) : Mon Nov 04, 2002
Time (hh/mm/ss) : 15:28:50
LBA Blk PIO 32Bit
Type Size Cyln Head WPcom Sec Mode Mode Mode Mode
Pri Master : Auto On
Pri Slave : Auto On
Sec Master : Auto On
Sec Slave : Auto On
Floppy Drive A : 1.44 MB 31/2
Floppy Drive B : Not Installed

Month : Jan – Dec ESC : Exit

Day : 01 – 31 ↑↓ : Select Item
Year : 1901 – 2099 PU/PD/+/- : Modify
(Shift)F2 : Color
F3 : Detect All HDD

Date and Time

The Date and Time items show the current date and time on the computer. If
you are running a Windows OS, these items are automatically updated when-
ever you make changes to the Windows Date and Time Properties utility.
IDE Pri Master/Pri Slave/Sec Master/Sec Slave
Use these items to configure devices connected to the Primary and Secon-
dary IDE channels. To configure an IDE hard disk drive, choose Auto. If the
Auto setting fails to find a hard disk drive, set it to User, and then fill in the
hard disk characteristics (Size, Cyls, etc.) manually. If you have a CD-ROM
drive, select the setting CDROM. If you have an ATAPI device with removable
media (e.g. a ZIP drive or an LS-120), select Floptical.
Floppy Drive A/Floppy Drive B
Use these items to set up size and capacity of the floppy diskette drive(s) in-
stalled in the system.

23
Advanced Setup Page
This option defines advanced information about your system.
AMIBIOS SETUP – ADVANCED SETUP
©2000 American Megatrends, Inc. All Rights Reserved
Quick Boot Enabled AGP Aperture Size 64MB
1st Boot Device IDE-0 Auto detect DIMM/PCI Clk Enabled
2nd Boot Device Floppy CLK Gen Spread Spectrum Disabled
3rd Boot Device CDROM Hyper Threading Function Disabled
Try Other Boot Devices Yes
S.M.A.R.T. for Hard Disks Disabled
BootUp Num-Lock On
Floppy Drive Swap Disabled
Floppy Drive Seek Disabled
Password Check Setup
Boot To OS/2 No ESC : Quit ↑↓←→ : Select Item
L2 Cache Enabled
F1 : Help PU/PD/+/- : Modify
System BIOS Cacheable Enabled
SDRAM Timing by SPD Disables F5 : Old Values (Shift)F2 : Color
SDRAM Frequency 100MHz F6 : Load BIOS Defaults
SDRAM CAS# Latency 2.5
SDRAM Bank Interleave Disabled F7 : Load Setup Defaults
AGP Mode 4X
AGP Comp. Driving Auto
Manual AGP Comp. Driving CB

Quick Boot
If you enable this item, the system starts up more quickly be elimination some
of the power on test routines.
1st Boot Device/2nd Boot Device/3rd Boot Device
Use these items to determine the device order the computer uses to look for
an operating system to load at start-up time.
Try Other Boot Device
If you enable this item, the system will also search for other boot devices if it
fails to find an operating system from the first two locations.
S.M.A.R.T. for Hard Disks
Enable this item if any IDE hard disks support the S.M.A.R.T. (Self-Monitoring,
Analysis and Reporting Technology) feature.
BootUp Num-Lock
This item determines if the Num Lock key is active or inactive at system start-
up time.
Floppy Drive Swap
If you have two diskette drives installed and you enable this item, drive A be-
comes drive B and drive B becomes drive A.
Floppy Drive Seek
If you enable this item, your system will check all floppy disk drives at start up.
Disable this item unless you are using an old 360KB drive.

24
Password Check
If you have entered a password for the system, use this item to determine, if
the password is required to enter the Setup Utility (Setup) or required both at
start-up and to enter the Setup Utility (Always).
Boot to OS/2 > 64MB
Enable this item if you are booting the OS/2 operating system and you have
more than 64MB of system memory installed.
L2 Cache
Leave these items enabled since all the processors that can be installed on
this board have internal L2 cache memory.
System BIOS Cacheable
If you enable this item, a segment of the system BIOS will be copied to main
memory for faster execution.
DOS Flat Mode
This item enables BIOS to enter the DOS protected mode without other soft-
ware supporting under the DOS operating system. We recommend you leave
this item at the default value.
SDRAM Timing By SPD
This item allows you to enable or disable the SDRAM timing defined by the
Serial Presence Detect electrical.
SDRAM Frequency
This item determines frequency of SDRAM memory.
SDRAM CAS# Latency
This item determines the operation of SDRAM memory CAS (column address
strobe). It is recommended that you leave this item at the default value. The
2T setting requires faster memory that specifically supports this mode.
SDRAM Bank Interleave
Enable this item to increase SDRAM memory speed. When enabled, separate
memory banks are set for odd and even addresses and the next byte of
memory can be accessed while the current byte is being refreshed.
AGP Comp. Driving
Use this item to signal driving current on AGP cards to auto or manual. Some
AGP cards need stronger than normal driving current in order to operate. We
recommend that you set this item to the default.
Manual AGP Comp. Driving
When AGP Driving is set to Manual, use this item to set the AGP current driv-
ing value.
AGP Mode
This item provides the OnBoard VGA mode with three options of 1,2, 4 multi-
plied frequency.

25
AGP Aperture Size
This item defines an AGP for the graphics. Leave this item at the default value
64MB.
Auto detect DIMM/PCI Clock
When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI
slots.
CLK GEN Spread Spectrum
Use this item to set the system bus spread spectrum for the installed proces-
sor.
Hyper Threading Function
This item is dependent when your system supports the Hyper-Threading
technology. If your system does not have the Hyper-Threading technology
installed, this item is hidden.

Power Management Setup Page

This page sets up some parameters of system power management operation.
AMIBIOS SETUP – POWER MANAGEMENT SETUP
©2000 American Megatrends, Inc. All Rights Reserved
ACPI Aware O/S Yes
Power Management Enabled
Suspend Time Out Disabled
Hard Disk Time Out Standby
Resume On RTC Alarm Disabled
RTC Alarm Date 15
RTC Alarm Hour 12
RTC Alarm Minute 30
RTC Alarm Second 30 ESC : Quit ↑↓←→ : Select Item
LAN/Ring Power On Disabled
Keyboard Power On Disabled F1 : Help PU/PD/+/- : Modify
Wake-Up Key Any key F5 : Old Values (Shift)F2 : Color
Wake-Up Password N/A
F6 : Load BIOS Defaults
F7 : Load Setup Defaults

ACPI Aware O/S

This item supports ACPI (Advanced Configuration and Power management
Interface). Use this item to enable or disable the ACPI feature.
Power Management
Use this item to enable or disable a power management scheme. If you en-
able power management, you can use the items below to set the power
management operation. Both APM and ACPI are supported.
Suspend Time Out
This sets the timeout for Suspend mode in minutes. If the time selected
passes without any system activity, the computer will enter power-saving Sus-
pend mode.

26
Hard Disk Time Out
This item sets up the timeout to power down the hard disk drive, if there is no
hard disk activity after passing the preset period of time.
Resume On RTC Alarm / Date / Hour / Minute / Second
The system can be turned off with a software command. If you enable this
item, the system can automatically resume at a fixed time based on the sys-
tem’s RTC (realtime clock). Use the items below this one to set the date and
time of the wake-up alarm. You must use an ATX power supply in order to use
this feature.
LAN/Ring Power On
The system can be turned off with a software command. If you enable this
item, the system can automatically resume if there is an incoming call on the
Modem. You must use an ATX power supply in order to use this feature.
Keyboard Power On /Wake-Up Key/Wake-Up/ Password
If you enable this item, system can automatically resume by pressing hot
keys on the keyboard or typing in the password. You must enable the Key-
board Power On jumper and use an ATX power supply in order to use this
feature.

PCI / Plug and Play Setup Page

This page sets up some parameters for devices installed on the PCI bus and
those utilizing the system plug and play capability.
AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP
©2000 American Megatrends, Inc. All Rights Reserved
Plug and Play Aware O/S Yes
Share Memory Size 32MB
Primary Graphics Adapter PCI
Allocate IRQ for PCI VGA Yes
PCI IDE BusMaster Disabled
ESC : Quit ↑↓←→ : Select Item
F1 : Help PU/PD/+/- : Modify
F5 : Old Values (Shift)F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults

Plug and Play Aware O/S

Enable this item if you are using an O/S that supports Plug and Play such as
Windows 95 or 98.
Share Memory Size
This item lets you allocate a portion of the main memory for the onboard VGA
display application with three options of 8/16/32MB.
Primary Graphics Adapter
This item indicates if the primary graphics adapter uses the PCI or the AGP
bus. The default PCI setting still lets the onboard display work and allows the

27
use of a second display card installed in a PCI slot.
Allocate IRQ for PCI VGA
If this item is enabled, an IRQ will be assigned to the PCI VGA graphics sys-
tem. You set this value to No to free up an IRQ.
PCI IDE BusMaster
This item enables or disables the DMA under DOS mode. We recommend you
to leave this item at the default value.

Load Optimal Settings

If you select this item and press Enter a dialog box appears. If you press Y,
and then Enter, the Setup Utility loads a set of fail-safe default values. These
default values are not very demanding and they should allow your system to
function with most kinds of hardware and memory chips.
Note: It is highly recommended that users enter this option to load optimal
values for accessing the best performance.

Load Best Performance Settings

If you select this item and press Enter a dialog box appears. If you press Y,
and then Enter, the Setup Utility loads a set of best-performance default val-
ues. These default values are quite demanding and your system might not
function properly if you are using slower memory chips or other low-
performance components.

Features Setup Page

This page sets up some parameters for those peripheral devices connected to
the system.
AMIBIOS SETUP – FEATURES SETUP
©2000 American Megatrends, Inc. All Rights Reserved
OnBoard FDC Enabled
OnBoard Serial PortA 3F8h/COM1
OnBoard IR Port Disabled
OnBoard Parallel Port 378h
Parallel Port Mode SPP
Parallel Port IRQ 7
Parallel Port DMA N/A
OnBoard Game Port 201h ESC : Quit ↑↓←→ : Select Item
OnBoard MIDI Port 300h
MIDI Port IRQ 10 F1 : Help PU/PD/+/- : Modify
OnBoard IDE Both F5 : Old Values (Shift)F2 : Color
Audio Device Enabled
Modem Device Auto F6 : Load BIOS Defaults
Ethernet Device Enabled F7 : Load Setup Defaults
USB Controller Enabled
USB Device Legacy Support Disabled
ThumbDrive Support for DOS Disabled

28
OnBoard FDC
Use this item to enable or disable the onboard floppy disk drive interface.
OnBoard Serial PortA
Use this item to enable or disable the onboard COM1 serial port, and to as-
sign a port address.
OnBoard IR Port
Use this item to enable or disable the onboard infrared port, and to assign a
port address.
Parallel Port Mode
Use this item to set the parallel port mode. You can select SPP (Standard
Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel
Port), or ECP + EPP.
Parallel Port IRQ
Use this item to assign IRQ to the parallel port.
Parallel Port DMA
Use this item to assign a DMA channel to the parallel port.
OnBoard Game Port
This item enables or disables the I/O address for the game port.
OnBoard MIDI Port
Use this item to enable or disable the onboard MIDI port, and to assign a port
address.
MIDI Port IRQ
Use this item to assign IRQ 7 to the parallel port.
OnBoard IDE
Use this item to enable or disable the onboard IDE channel.
Audio Device
This item enables or disables the AC’97 audio chip.
Modem Device
This item enables or disables the MC’97 modem chip.
Ethernet Device
This item enables or disables the onboard Ethernet LAN.
USB Controller
Use this item to select the USB ports or disabled.
USB Device Legacy Support
This item allows you to enable the USB device, if you have installed a USB
device on the system board.

29
ThumbDrive Support For DOS
Enable this item to make a small portion of memory storage device for the
USB ports.

CPU PnP Setup Page

This page helps you manually configure the mainboard for the CPU. The sys-
tem will automatically detect the type of installed CPU and make the
appropriate adjustments to the items on this page.
AMIBIOS SETUP – CPU PnP SETUP
©2000 American Megatrends, Inc. All Rights Reserved
CPU BRAND INTEL
CPU Type Pentium 4
CPU Ratio 8.0x
CPU Frequency 100 MHz

ESC : Quit ↑↓←→ : Select Item

F1 : Help PU/PD/+/- : Modify
F5 : Old Values (Shift)F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults

CPU BRAND/Type/ Core Voltage/Ratio /Frequency

These items show the type, core voltage, ratio and frequency of CPU installed
in your system.

Hardware Monitor Page

On mainboards that support hardware monitoring, this item lets you monitor
the parameters for critical voltages, critical temperatures, and fan speeds:
AMIBIOS SETUP – HARDWARE MONITOR
©2000 American Megatrends, Inc. All Rights Reserved
*** System Hardware ***
Vcore 1.632V
Vcc 2.5V 2.496V
Vcc 3.3V 3.392V
Vcc 5V 4.945V
+12V 12.032V
-12V -11.968V
SB5V 5.026V ESC : Quit ↑↓←→ : Select Item
VBAT 3.488V
SYSTEM Fan Speed 0 RPM F1 : Help PU/PD/+/- : Modify
CPU Fan Speed 1308 RPM F5 : Old Values (Shift)F2 : Color
Power Temperature 33°C/91°F
F6 : Load BIOS Defaults
SYSTEM Temperature 39°C/102°F
CPU Temperature 62°C/143°F F7 : Load Setup Defaults

30
CPU / System Temperature
These items display CPU and system temperature measurement.
FANs & Voltage Measurements
These items indicate cooling fan speeds in RPM and the various system volt-
age measurements.

Change Password
If you highlight this item and press Enter, a dialog box appears that you can
enter a Supervisor password. You can enter no more than six letters or num-
bers. Press Enter after you have typed in the password. There will be the
second dialog box asking you to retype the password for confirmation. Press
Enter after you have retyped it correctly. Then, the password is required for
the access to the Setup Utility or for it at start-up, depending on the setting of
the Password Check item in Advanced Setup.

Exit
Highlight this item and press Enter to save the changes that you have made in
the Setup Utility configuration and exit the program. When the Save and Exit
dialog box appears, press Y to save and exit, or press N to exit without saving.
This concludes Chapter 3. Refer to the next chapter for information on the
software supplied with the mainboard.

Chapter 4
31
 Using the Mainboard Software

About the Software CD-ROM

The support software CD-ROM that is included in the mainboard package
contains all the drivers and utility programs needed to properly run the bun-
dled products. Below you can find a brief description of each software
program, and the location for your mainboard version. More information on
some programs is available in a README file, located in the same directory
as the software.
Note: Never try to install software from a folder that is not specified for use with
your mainboard.

Before installing any software, always inspect the folder for files named RE-
ADME.TXT, INSTALL.TXT, or something similar. These files may contain
important information that is not included in this manual.

Auto-installing under Windows 98/ME/2000/XP

The Auto-install CD-ROM makes it easy for you to install the drivers and soft-
ware for your mainboard.
Note: If the Auto-install CD-ROM does not work on your system, you can still in-
stall drivers through the file manager for your OS (for example, Windows
Explorer). Refer to Utility Folder Installation Notes later in this chapter.

The support software CD-ROM disc loads automatically under Windows

98/ME/2000/XP. When you insert the CD-ROM disc in the CD-ROM drive, the
autorun feature will automatically bring up the install screen. The screen has
three buttons on it, Setup, Browse CD and Exit.

Note: If the opening screen doesn't appear, double-click the file "setup.exe" in
the root directory.

32
Setup Tab
Setup Click the Setup button to run the software installation program.
Select from the menu which software you want to install.
Browse The Browse CD button is the standard Windows command that
CD allows you to open Windows Explorer and show the contents of
the support CD.
Before installing the software from Windows Explorer, look for a
file named README.TXT, INSTALL.TXT or something similar.
This file may contain important information to help you install the
software correctly.
Some software is installed in separate folders for different oper-
ating systems, such as DOS, WIN NT, or WIN98/95. Always go
to the correct folder for the kind of OS you are using.
To install the software, execute a file named SETUP.EXE or
INSTALL.EXE by double-clicking the file and then following the
instructions on the screen.
Exit The Exit button closes the Auto Setup window.

Application Tab
Lists the software utilities that are available on the CD.

Read Me Tab
Displays the path for all software and drivers available on the CD.

Running Setup
Follow these instructions to install device drivers and software for the main-
board:
1. Click Setup. The installation program begins:

Mainboard ID

33
 Note: The following screens are examples only. The screens and driver lists will
be different according to the mainboard you are installing.
The mainboard identification is located in the upper left-hand corner.
2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default options
are recommended.
4. Click Next run the Installation Wizard. An item installation screen ap-
pears:

5. Follow the instructions on the screen to install the items.

Drivers and software are automatically installed in sequence. Follow the on-
screen instructions, confirm commands and allow the computer to restart a
few times to complete the installation.

34
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root
directory. This file contains the information needed to locate the drivers for
your mainboard.
Look for the chipset and mainboard model; then browse to the directory and
path to begin installing the drivers. Most drivers have a setup program
(SETUP.EXE) that automatically detects your operating system before installa-
tion. Other drivers have the setup program located in the operating system
subfolder.
If the driver you want to install does not have a setup program, browse to the
operating system subfolder and locate the readme text file (README.TXT or
README.DOC) for information on installing the driver or software for your
operating system.

Utility Software Reference

All the utility software available from this page is Windows compliant. They are
provided only for the convenience of the customer. The following software is
furnished under license and may only be used or copied in accordance with
the terms of the license.
Note: These software(s) are subject to change at anytime without prior notice.
Please refer to the support CD for available software.

AWARD Flash Memory Utility

This utility lets you erase the system BIOS stored on a Flash Memory chip on
the mainboard, and lets you copy an updated version of the BIOS to the chip.
Proceed with caution when using this program. If you erase the current BIOS
and fail to write a new BIOS, or write a new BIOS that is incorrect, your sys-
tem will malfunction. Refer to Chapter 3, Using BIOS for more information.

WinFlash Utility
The Award WinFlash utility is a Windows version of the DOS Award BIOS
flash writer utility. The utility enables you to flash the system BIOS stored on a
Flash Memory chip on the mainboard while in a Windows environment. This
utility is currently available for WINXP\ME\2000\98SE. To install the WinFlash
utility, run WINFLASH.EXE from the following directory:
\UTILITY\WINFLASH 1.51

PC-CILLIN 2002
The PC-CILLIN 2002 software program provides anti-virus protection for your
system. This program is available for Windows 2000/ME/98SE/XP and Win-
dows NT. Be sure to check the readme.txt and install the appropriate anti-virus
software for your operating system.

35
We strongly recommend users to install this free anti-virus software to help
protect your system against viruses.

MediaRing Talk – Telephony Software

To install the MediaRing Talk voice modem software for the built-in modem, go
to the directory \UTILITY\MEDIARING TALK, then run MRTALK-
SETUP72.EXE to install the application software.

Super Voice – Fax/Modem Software

To install the Super Voice voice, fax, data communication application for use
with the built-in fax/modem, go the directory \UTILITY\SUPER_VOICE, then
run PICSHELL.EXE to install the application software.

PageABC
The PageABC application software enables you to create your very own home
page. To install the PageABC, go to the directory \UTILITYPageABC, and then
run SETUP.EXE to install the application software.

This concludes Chapter 4.

36