DESIGN DECISION --

ADVANTAGES WITH
ALUMINUM EXTRUSIONS
There are any number of ways in
which extruded aluminum can be
applied to meet design challenges
more effectively, more efficiently, or
more economically than alternative
methods of manufacture. The
following illustrations offer just a few
common examples.

1. As shown, several rolled shapes,

riveted together, can be replaced by a
single extruded profile, resulting in
higher strength while eliminating
joining costs.

2. Machining costs often can be

reduced by extruding the desired
component to exact size and shape
requirements.

3. Weight can be greatly decreased

by putting the metal only where
needed. The extrusion process can
put the metal exactly where needed.

Section 6 Designing 6-4

 4. Welded assemblies frequently can
be eliminated by designing an appro-
priate extrusion. In this way, costs
can be reduced while both strength
and accuracy are increased.

5. Sturdy multi-void hollow profiles

are available to replace roll-formed
alternatives, often at reduced set-up
costs and shortened lead times.

6. Improved stiffness and strength

can be achieved through extrusion.
Here, a detailed hollow profile
replaces a crimped tubular section, at
a reduced manufacturing cost.

Advantages

Aluminum Extrusion Manual 6-5

Circumscribing Circle Size Most common profiles are less than
One common measurement of the 18 inches in diameter, but a few
size of an extrusion is the diameter extruders are capable of producing
of the smallest circle that will entirely extrusions with a much larger
enclose its cross-section--its circumscribing circle diameter
circumscribing circle. (CCD), some as large as 32 inches.

This dimension is one factor in the

economics of an extrusion.
In general, extrusions are most
economical when they fit within a
medium-sized circumscribing circle: The example shown here would be classified
as a 3-to-4-inch circle-size shape.
that is, one with a diameter between
one and ten inches.
18”+
10”
9”
8”
7”
6”
5”
4”
3”
2”

Not to scale

Section 6 Designing 6-10

DESIGN DECISION --
PRACTICES
To develop a good extrusion design,
the following key characteristics
should be addressed:
• Specify the appropriate metal
thickness
• Keep metal thickness as uniform
as possible Rounded corners ease the flow of metal.
• Use metal dimensions for
tolerances Keep Metal Thickness As Uniform
• Design with surface finish in mind As Possible
• Smooth transitions Extrusion allows you to put extra
• Use webs where possible metal where it is needed--in high-
• Use ribs to straighten stress areas, for example--and still
• Round corners wherever possible, save material by using normal
avoiding sharp edges dimensions elsewhere in the same
• Incorporate indexing marks. piece. Adjacent-wall thickness ratios
Specify the Most Appropriate of less than two-to-one are extruded
Metal Thicknesses without difficulty, but large differ-
Specify metal thicknesses that are just ences between thick and thin areas
heavy enough to meet your structural may create dimensional control prob-
requirements. Even in low stress lems during extrusion. It is best to
areas, however, keep sufficient thick- maintain near uniform metal thick-
ness to avoid risking distortion or ness throughout a shape if possible.
damage. Some shapes tend to invite When a design combines thick and
distortion during the extrusion thin dimensions, streamline the tran-
process (such as an asymmetric pro- sitions with a radius (a curve, rather
file or thin details at the end of a than a sharp angle) at junctions
long flange); such tendencies exert where the thickness changes sharply.
more influence on thin-walled shapes
than on those with typical metal
thickness.

Practices

Metal thicknesses should be appropriate.

Aluminum Extrusion Manual 6-11

 3.00
±.024
Use Metal Dimensions for Best
Tolerance
Dimensions measured across solid
metal are easier to produce to close
A "Metal Dimension"
tolerances than those measured can be extruded to
across a gap or angle. So rely on so- close tolerances.
called metal dimensions as much as
possible when designing close-fitted
mating parts or other shapes requir-
3.00
ing closer tolerances. Standard
±.057
industry dimensional tolerances are
entirely adequate for many applica-
tions, but special tolerances can be
specified if necessary.

An "Open Space
Dimension" is more
difficult to hold to
close tolerances.

Design with Surface Finish in Mind

Always indicate "exposed surfaces"
on your design drawing so the
extruder can give them special
This shape, with sharp
attention and protect their finish angular transitions,
during both extrusion and post- risks show-through
extrusion handling. streaks on the opposite
surface.
As a general rule, the narrower the
exposed surface, the more uniform
its finish.

Webs, flanges, and abrupt changes

in metal thickness may show up as
marks on the opposite surface of
an extrusion, particularly on thin
sections. The marking of exposed
Modifying the shape
surfaces can be minimized by by rounding the
thoughtful design. transitions reduces
the chance of oppo-
site-side streaking.

Section 6 Designing 6-12

Smooth All Transitions in Thickness
Transitions should be streamlined by
a generous radius at any thick-thin Smooth transitions
can be achieved
junction. through rounding
corners.

The hollow condition

Web Gives Better Dimensional
of the part can be
Control avoided by making
Metal dimensions are more easily the component in two
held than gap or angle dimensions. pieces as shown by
The web also allows thinner wall sec- the dotted line.
tions in this example.

Ribs Help Straightening Operation

Wide, thin sections can be hard to
straighten after extrusion. Ribs help Ribs reduce twisting.
to reduce twisting, and to improve
flatness.

Rounded Corner Strengthens Tongue Rounded corners are

The die tongue is less likely to snap stronger corners.
off when the corners of the profile
are rounded at the narrowest area of
the void.

Built-In Indexing Mark

Shallow extruded grooves make
drilling, punching, and assembly
easier by eliminating the need for
center-punching. An index groove An extruded groove
can also be used to help identify could eliminate the
need for center-
pieces that are similar in appearance, punching.
or to distinguish an inside (rather
than an outside) surface.

Aluminum Extrusion Manual 6-13

 Snap-fit Heat Sink Integral Patterned
assembly Tube on leg Surface for
DESIGN DECISION -- appearance
ASSEMBLY Dovetail Hinge
Extruded shapes can incorporate assembly
essential design features such as screw Screw Boss
bosses, card slots, or drill guides. on leg
Groove
Thus, aluminum profiles enhance the to accept “Christmas Tree”
usefulness of the part produced. printed for joining with
circuit wood or plastic

The joining of aluminum extrusions cards

Anti-skid
can be accomplished by way of nine traction
distinct methods that can be Screw Boss pattern
designed into the profiles themselves.
Fluted Surface Groove for
1. nesting
for appearance rubber
2. interlocking
molding
3. snap-fit Groove for
Slot for nut or bolt
screw or rivet
4. three-piece interlock
Drill grooves
5. combination
6. slip-fit
7. hinge joint
8. key-lock joint
9. screw slot

Nesting Joints A nesting joint.

Nesting joints which include lap
joints and tongue-and-groove joints,
have mating elements that are shaped
to be assembled with little or no self-
locking action.

Interlocking Joints
The interlocking joint is, in effect, a
modified tongue-and-groove. But
instead of being straight, the two mat-
ing elements are curved; therefore,
they cannot be assembled or (more
to the point) disassembled by simple
straight-line motion. They are assem-
bled by a rotating motion and will
not separate without a corresponding
An Interlocking joint.
counter-rotation. As long as the parts
are held in their assembled position,
they strongly resist separation and
misalignment in both the horizontal
and the vertical directions.

Section 6 Designing 6-14

Snap-Fit Joints
A "snap-fit" or "snap-lock" joint is one
which is self-locking and requires no
additional fasteners to hold the joint
together.

The mating parts of a snap-fit joint

A snap-fit joint
exert a cam action on each other,
flexing until one part slips past a
raised lip on the other part. Once
past this lip, the flexed parts snap
back to their normal shape and the
lip prevents them from separating.
After it is snapped together, this joint
cannot be disassembled
unintentionally.

A Three-Piece Interlocking Joint

A three-piece joint can be designed
with a blind (hidden) fastener inter-
locking the two principal extrusions.
Such a design presents one side with
a smooth appearance and no visible
mounting hardware.
A three-piece interlocking joint.

Combination Joints
Nesting, interlocking and snap-fit
joints can be combined in the same In the example below, a single extruded shape is designed for mating
extruded assembly. with identical parts that are rotated into assembly and then snap-locked
rigidly into position without auxiliary fastening. The tight surface-to-
surface contact in this design also provides resistance to sliding
For example, snap-fit elements can
between the parts.
easily be combined with rotating
elements.

Assembles with self

Assembly

Aluminum Extrusion Manual 6-15

Slip-Fit Joints
Slip-fit joints are assembled by sliding
two extruded mating parts together
in the direction of their length.
They are generally classified either as
close-fitting, rigid dovetail joints or
as loose, freely-rotating hinge joints.

Dovetail joints are useful in many

products where a simple, strong, This dovetail joint is a type of slip-fit joint.
permanent connection is required.

Hinge Joints
The cross-section of the components
of a hinge joint have ball-and-socket
shapes that allow them to rotate with-
out separating. Hinge action
through 60 to 90 degrees is easy to
obtain; incorporating adequate rein-
forcement, hinge joints may be
designed to rotate beyond 90
degrees. Since the hinge joint is rel-
atively "loose," provisions should be
made to prevent lateral (side-to side)
slippage. A pair of extruded components make up this hinge joint.

A number of profiles could be assembled in series for this type of hinge joint.

Section 6 Designing 6-16

Key-Locked Joints Keyed interlocks of this type permit
These unusual joints have two or rapid, easy assembly and disassembly,
more primary elements which are making them particularly adaptable to
locked together only when an addi- temporary and portable installations, as
tional specialized part, the key, is slid well as relatively permanent structures.
into position.

The joint shown here is used to

connect two or more panels. In the This unique key-locked joint won an award
illustration, two panels and their in an international extrusion design
competition cosponsored by The Aluminum
extruded joining elements are seen
Association and the Aluminum Extruders
edge-on from the top or bottom. Council.
The three hook-profiled extrusions
nest together, but are not in fact
joined until an extruded pin with a
special profile is inserted into the
space at the center, locking them in
place.

Assembly

Aluminum Extrusion Manual 6-17