SIMS-201

What is Bandwidth and

How it is Used
Overview
 Chapter 16 (continued)
 Bandwidth
 Shannon’s theorem
 Communication systems
 Analog Modulation
 AM
 FM
 Digital Modulation
 ASK
 FSK
 Modems
2
Bandwidth
 In previous lectures, we briefly mentioned the concept of
bandwidth. In this lecture, we will discuss more deeply what
signal bandwidth is, what the meaning of channel bandwidth to
a communications engineer is, and what the limitations on
information rate are.
 Signal bandwidth:
 We can divide signals into two categories: The pure tone signal (the
sinusoidal wave, consisting of one frequency component), and complex
signals that are composed of several components, or sinusoids of various
frequencies.
T=1x10-3 s f=1/1x10-3
=1000Hz=1 kHz

0 1 t (ms)

Pure signal
3
 The bandwidth of a signal composed of components of various frequencies (complex signal) is
the difference between its highest and lowest frequency components, and is expressed in Hertz
(Hz) - the same as frequency.
 For example, a square wave may be constructed by adding sine waves of various frequencies:

Pure tone
150 Hz sine wave

Pure tone
450 Hz sine wave

Approaching a 150 Hz
square wave
(ms)
 The resulting wave resembles a square wave. If more sine waves of other frequencies were
added, the resulting waveform would more closely resemble a square wave
 Since the resulting wave contains 2 frequency components, its bandwidth is around 450-
150=300 Hz.

4
 Male voice
 Since voice signals are also 3000 Hz
composed of several
components (pure tones) of frequency
various frequencies, the component
bandwidth of a voice signal is
taken to be the difference
between the highest and lowest
frequencies which are 3000 Hz
and (close to) 0 Hz
 Although other frequency
components above 3000 Hz
exist, (they are more prominent
in the male voice), an Female voice
acceptable degradation of voice
quality is achieved by 3000 Hz
disregarding the higher frequency
frequency components, component
accepting the 3kHz bandwidth
as a standard for voice
communications
5
  channel bandwidth:
 The bandwidth of a channel (medium) is defined to be the range of
frequencies that the medium can support. Bandwidth is measured
in Hz
 With each transmission medium, there is a frequency range of
electromagnetic waves that can be transmitted:
 Twisted pair cable: 0 to 109 Hz (Bandwidth : 109 Hz)
Increasing  Coax cable: 0 to 1010 Hz (Bandwidth : 1010 Hz)
bandwidth  Optical fiber: 1014 to 1016 Hz (Bandwidth : 1016 -1014 = 9.9x1015 Hz)

 Optical fibers have the highest bandwidth (they can support

electromagnetic waves with very high frequencies, such as light
waves)
 The bandwidth of the channel dictates the information carrying
capacity of the channel
 This is calculated using Shannon’s channel capacity formula

6
Shannon’s Theorem
(Shannon’s Limit for Information Capacity)

 Claude Shannon at Bell Labs figured out how much

information a channel could theoretically carry:
Note that the log
I = B log2 (1 + S/N) is base 2!

 Where I is Information Capacity in bits per second

(bps)
 B is the channel bandwidth in Hz
 S/N is Signal-to-Noise ratio (SNR: unitless…don’t
make into decibel: dB)
7
Signal-to-Noise Ratio

 S/N is normally measured in dB (decibel). It is a

relationship between the signal we want versus the
noise that we do not want, which is in the medium.

 It can be thought of as a fractional relationship (that

is, before we take the logarithm):

 1000W of signal power versus 20W of noise power is

either:
 1000/20=50 (unitless!)

or: about 17 dB ==> 10 log10 1000/20 = 16.9897 dB

8
Communication systems

Digital

Analog

 The block diagram on the top shows the blocks common to all
communication systems
9
We recall the components of a communication
system:
 Input transducer: The device that converts a physical signal
from source to an electrical, mechanical or electromagnetic
signal more suitable for communicating
 Transmitter: The device that sends the transduced signal
 Transmission channel: The physical medium on which the
signal is carried
 Receiver: The device that recovers the transmitted signal from
the channel
 Output transducer: The device that converts the received signal
back into a useful quantity

10
 Analog Modulation
 The purpose of a communication system is to transmit information signals
(baseband signals) through a communication channel
 The term baseband is used to designate the band of frequencies
representing the original signal as delivered by the input transducer
 For example, the voice signal from a microphone is a baseband signal,
and contains frequencies in the range of 0-3000 Hz
 The “hello” wave is a baseband signal:

11
 Since this baseband signal must be transmitted through a communication channel (such
as air or cable) using electromagnetic waves, a procedure is needed to shift the range
of baseband frequencies to other frequency ranges suitable for transmission; and, a
corresponding shift back to the original frequency range after reception. This is called
the process of modulation and demodulation

 Remember the radio spectrum:

 For example, an AM radio system transmits electromagnetic waves with frequencies of

around a few hundred kHz (MF band)
AM radio FM radio/TV
 The FM radio system operates with frequencies in the range of 88-108 MHz (VHF band)

12
 Since the baseband signal contains frequencies in the audio frequency range (3
kHz), some form of frequency-band shifting must be employed for the radio
system to operate properly
 This process is accomplished by a device called a modulator
 The transmitter block in any communications system contains the modulator
device
 The receiver block in any communications system contains the demodulator
device
 The modulator modulates a carrier wave (the electromagnetic wave) which has
a frequency that is selected from an appropriate band in the radio spectrum
 For example, the frequency of a carrier wave for FM can be chosen from
the VHF band of the radio spectrum
 For AM, the frequency of the carrier wave may be chosen to be around a
few hundred kHz (from the MF band of the radio spectrum)
 The demodulator extracts the original baseband signal from the received
modulated signal

In Summary:
 Modulation is the process of impressing a low-frequency information signal
(baseband signal) onto a higher frequency carrier signal
13
Basic analog communications system
Baseband signal
EM waves (modulated
(electrical signal) Transmitter signal)

Input Transmission
transducer Modulator
Channel

EM waves (modulated
Carrier signal)
Baseband signal
(electrical signal) Receiver

Output
Demodulator
transducer

14
 Types of Analog Modulation
 Amplitude Modulation (AM)
 Amplitude modulation is the process of varying the amplitude

of a carrier wave in proportion to the amplitude of a

baseband signal. The frequency of the carrier remains constant

 Frequency Modulation (FM)

 Frequency modulation is the process of varying the frequency

of a carrier wave in proportion to the amplitude of a

baseband signal. The amplitude of the carrier remains constant

 Phase Modulation (PM)

 Another form of analog modulation technique which we will not

discuss
15
Amplitude Modulation

Carrier wave

Baseband signal

Modulated wave

Amplitude varying-
frequency constant 16
Frequency Modulation

Carrier wave

Small amplitude: Large amplitude:

Baseband signal high frequency
low frequency

Modulated wave
Frequency varying-
amplitude constant

17
AM vs. FM
 AM requires a simple circuit, and is very easy to generate.
 It is simple to tune, and is used in almost all short wave broadcasting.
 The area of coverage of AM is greater than FM (longer wavelengths
(lower frequencies) are utilized-remember property of HF waves?)
 However, it is quite inefficient, and is susceptible to static and other
forms of electrical noise.

 The main advantage of FM is its audio quality and immunity to noise.

Most forms of static and electrical noise are naturally AM, and an FM
receiver will not respond to AM signals.
 The audio quality of a FM signal increases as the frequency deviation
increases (deviation from the center frequency), which is why FM
broadcast stations use such large deviation.
 The main disadvantage of FM is the larger bandwidth it requires

18
Digital Modulation
 The previous section presented analog communication systems
that transmit information in analog form using Amplitude or
Frequency modulation

 Digital communication systems also employ modulation

techniques, some of which include:
 Amplitude Shift Keying
 Frequency Shift Keying
 Phase Shift Keying

19
 Basic digital communications
system Transmitter EM waves (modulated
Digital signal
signal)
Analog signal

correction
converter
Transmission

coding
Input Modulator

Error
transducer A/D Channel

Carrier EM waves
Receiver (modulated signal)
analog signal digital signal

correction
detection/
converter

Output Error Demodulator

transducer
D/A

20
 Some Types of Digital Modulation
 Amplitude Shift Keying (ASK)
 The most basic (binary) form of ASK involves the process of
switching the carrier either on or off, in correspondence to a
sequence of digital pulses that constitute the information signal.
One binary digit is represented by the presence of a carrier, the
other binary digit is represented by the absence of a carrier.
Frequency remains fixed
 Frequency Shift Keying (FSK)
 The most basic (binary) form of FSK involves the process of varying
the frequency of a carrier wave by choosing one of two frequencies
(binary FSK) in correspondence to a sequence of digital pulses that
constitute the information signal. Two binary digits are represented
by two frequencies around the carrier frequency. Amplitude
remains fixed
 Phase Shift Keying (PSK)
 Another form of digital modulation technique which we will not
discuss 21
 Amplitude Shift Keying
Digital 1 0 1 1 0 0 1 0 1 0
information

Carrier wave

ASK
modulated
signal

Amplitude varying-
frequency constant
Carrier present Carrier absent

22
 Frequency Shift Keying
1 0 1 1 0 0 1
Digital
information

Carrier 1
(frequency #1)
Carrier 2
(frequency #2)
FSK
modulated
signal

Frequency varying-
amplitude constant

23
Modems
 Modems are devices used to enable the transfer of data over the public switched
telephone network (PSTN)
 The name modem comes from the name MOаulator- DEModulator which
describes the function the modem performs to transfer digital information over
an analog network
 The goal is to produce a signal that can be transmitted easily and decoded to
reproduce the original digital data. Primarily used to communicate via telephone
lines, modems can be used over any means of transmitting analog signals
 There are many kinds of modems available today:
 Internal modem:
 A modem card inside a computer
 Less expensive than external modems
 Disadvantage is that it is necessary to access inside the computer to replace the
modem
 External modem
 A device that connects externally a computer (through a port)
 External power supply does not drain power from the computer
 Modem activity can easily be observed
 More expensive than an internal modem
Source: http://Wikipedia.com
24
 DSL (Digital Subscriber Line)
 A high-speed data service that works over conventional telephone lines
and is typically offered by telephone companies
 It does not occupy the phone line - we can still talk on the phone
 Speed is much higher than regular modem

 Cable modem
 A device that connects to the existing cable feed and to a network card
in the PC (also called a NIC for Network Interface Card)
 No dial up necessary
 Supports higher speeds
 Typically offered by cable companies

 Modems are the most popular means of Internet access

25