Scribd Logo
Upload

Welcome to Scribd!

  • 43 views

    DI67

    Uploaded by

    Erln Lima
    The document provides diagnostic steps to check the clutch switch circuit for the cruise control system on a Toyota Tacoma with ETCS-i. It describes the circuit, shows the wiring diagram, and lists 4 inspection procedures to check: 1) starter operation, 2) the input signal with the indicator light, 3) voltage at the ECM terminal when the clutch is depressed/released, and 4) the wire harness and connector between the ECM and gauge fuse.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    DI67

    Uploaded by

    Erln Lima
    43 views3 pages
    The document provides diagnostic steps to check the clutch switch circuit for the cruise control system on a Toyota Tacoma with ETCS-i. It describes the circuit, shows the wiring diagram, and lists 4 inspection procedures to check: 1) starter operation, 2) the input signal with the indicator light, 3) voltage at the ECM terminal when the clutch is depressed/released, and 4) the wire harness and connector between the ECM and gauge fuse.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides diagnostic steps to check the clutch switch circuit for the cruise control system on a Toyota Tacoma with ETCS-i. It describes the circuit, shows the wiring diagram, and lists 4 inspection procedures to check: 1) starter operation, 2) the input signal with the indicator light, 3) voltage at the ECM terminal when the clutch is depressed/released, and 4) the wire harness and connector between the ECM and gauge fuse.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    43 views3 pages

    DI67

    Uploaded by

    Erln Lima
    The document provides diagnostic steps to check the clutch switch circuit for the cruise control system on a Toyota Tacoma with ETCS-i. It describes the circuit, shows the wiring diagram, and lists 4 inspection procedures to check: 1) starter operation, 2) the input signal with the indicator light, 3) voltage at the ECM terminal when the clutch is depressed/released, and 4) the wire harness and connector between the ECM and gauge fuse.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    DI–710

    DIAGNOSTICS – CRUISE CONTROL SYSTEM (w/ ETCS–i)


    DIA7U–03

    Clutch Switch Circuit (M/T)

    CIRCUIT DESCRIPTION
    When the clutch pedal is depressed, the clutch switch sends a signal to the ECM. When the signal is input
    to the ECM during cruise control driving, the ECM cancels the cruise control.

    WIRING DIAGRAM

    ECM

    C16
    Cruise Control
    J/B No. 1 J/B No. 3
    Clutch SW
    2 GAUGE 5 19 13 25
    B–R B–R B–W
    1I 1F 3D 3D E6 D
    1 2

    B–Y

    From
    Ignition SW

    I26137

    INSPECTION PROCEDURE

    1 Check starter operation.

    CHECK:
    Check that the starter operates normally and that the engine starts.

    NG Proceed to engine troubleshooting.

    OK

    2003 TOYOTA TACOMA (RM1002U)

    Author: Date: 972


    DI–711
    DIAGNOSTICS – CRUISE CONTROL SYSTEM (w/ ETCS–i)

    2 Check input signal.

    PREPARATION:
    Input Signal Indicator Light
    Blinking Pattern See the input signal check on page DI–691.
    CHECK:
    Light
    Turn PNP Switch ON SW ON Check the indicator light when shifting into any positions except
    OFF D.
    (Shift into posi- SW OFF
    OFF
    tions except D ) OK:
    The indicator light goes off when shifting into any
    positions except D.

    OK Proceed to next circuit inspection shown in


    problem symptoms table (See page DI–700).

    NG

    3 Check voltage between terminal D of ECM connector and body ground.

    PREPARATION:
    Turn the ignition switch ON.
    E6
    CHECK:
    Measure the voltage between terminal E6–25 (D) of the ECM
    connector and the body ground when the clutch pedal is de-
    pressed and released.
    D (+) OK:
    Clutch Pedal Voltage
    I25145
    Released 10 – 14 V
    Depressed Below 1 V

    OK Proceed to next circuit inspection shown in


    problem symptoms table (See page DI–700).

    NG

    2003 TOYOTA TACOMA (RM1002U)

    Author: Date: 973


    DI–712
    DIAGNOSTICS – CRUISE CONTROL SYSTEM (w/ ETCS–i)

    4 Check wire harness and connector between ECM and GAUGE fuse (See page
    IN–28).

    NG Repair or replace harness or connector.

    OK

    Check and replace ECM (See page IN–28).

    2003 TOYOTA TACOMA (RM1002U)

    Author: Date: 974

    You might also like