Application of the Pathloss Software

Contents

 Overview

 Importing the Data

 Pre-Planning Routes

 Outputting the Information

Overview
• Purpose
1. Masters the basic operations of the Pathloss.
2. Pre-plans the microwave routes by using the Pathloss.

• Studied Case
Area: Mauritius, which is located in the east longitude and south
latitude, Southern Hemisphere

Basic information of the site:

High- accuracy electronic map (in the Planet_UTM format):

 Overview
• The Pathloss software is a comprehensive path design tool based on the radio links. The
Pathloss software operates at frequencies ranging from 30 MHz to 100 GHz. Currently,
Pathloss 4.0 is commonly used.
• Generally, electronic maps in three formats are used for the Pathloss software. They are
described as follows:
1. Electronic map released with the software
The accuracy of this map is 900 meters. The map is carried in two disks as follows:
Disk 1-map covering the North and South America
Disk 2-map covering the Europe, Africa and Asia
2. Electronic map in the SRTM format
This kind of map is classified into the following three categories:
SRTM 1': The accuracy of this map is 30 meters. Only the electronic map covering part of
the North America is available.
SRTM 3':The accuracy of this map is 90 meters. The high-accuracy electronic map
covering the entire globe is available. It is commonly used.
SRTM 30': The accuracy of this map is 900 meters. The high-accuracy electronic map
covering the entire globe is available.
3. Electronic map in the Planet_UTM format
This kind of map has high accuracy, which ranges from several meters to tens of meters.
You can obtain it form the Radio Network Planning Dept.
 Overview
Four versions of the Pathloss Software
• PL4B: basic design software for microwave transmission
• PL4C: basic design software for microwave transmission + 　　 coverage
calculation
• PL4I: basic design software for microwave transmission + interference analysis
• PL4CI: basic design software for microwave transmission + coverage calculation
+ interference analysis
Overview
Requirements for Installing the Pathloss Software
• The computer should be of the Pentium series, and should run in the Windows
95/98 (or a later version) or Windows NT 4.0 (or a later version) operating
system.
• The Pathloss software (with few database engines) requires a minimum of 6-
Mbyte hard disk space. More database engines and various data files will
increase the requirement for the hard disk space to 25 Mbytes.
• A memory with a capacity of more than 64 Mbytes is required when the
computer runs in the Windows 95/98 operating system, or a memory with a
capacity of more than 128 Mbytes is required when the computer runs in the
Windows NE operating system.
• The authentication of license (in a floppy disk or in a dongle) is required.
• You can obtain these contents at the website of CTE: www.pathloss.com
Overview
Uninstallation of the Pathloss
License in a floppy disk:
• Choose Configure > Program > Uninitialize Program from the menu in the Pathloss.
• Click Start, and select Control Panel. In the displayed window, choose Add or Remove Programs >
Change or Remove Programs > Pathloss 4.0.
License in a USB
• Click Start, and select Control Panel. In the displayed window, choose Add or Remove Programs >
Change or Remove Programs > Pathloss 4.0.
Contents

 Overview

 Importing the Data

 Pre-Planning Routes

 Outputting the Information

Importing the Data
• Processing the Data

• Importing the Electronic Map

1. Importing the electronic map released with the software
• Click Start, and choose Program > Pathloss 4.0 to run the software.
• Choose Configure > Terrain Database from the menu of the Pathloss. (In the displayed dialog
box, according to the format of the map released with the software, GTopo30 Global 30 sec
under Primary is generally selected.)
Importing the Data
• Click Setup Primary, and then click Set Directory in the Gtopo30 Global 30 sec dialog box to set the directory that
contains the information of the map to be used in the network planning. When the directory setting is complete, click OK.
Click Close in the GTopo30 Global 30 sec dialog box, and then click OK in the Configure Terrain Database dialog box.
Importing the Data
2. Importing the electronic map in the SRTM format
• Run the Pathloss software, and choose Configure > Terrain Database from the menu of the Pathloss. In
the displayed dialog box, select SRTM under Primary.
• Click Setup Primary, and the SRTM window is displayed. Choose Files > BIL-HDR-BLW to select the
proper map (in the format of *.hgt).
Importing the Data
3. Importing the electronic map in the Planet_UTM format
Run the Pathloss software, and choose Configure > Geographic Defaults from the menu of the
Pathloss. In the displayed Geographic Defaults dialog box, modify the values in Datum and Ellipsoid to the formats
specified in the Projection file. Select the proper items under Latitude, Longitude and Use as required. Under Grid
Coordinate System, select Universal Transverse Mercator (UTM). Modify other items according to the actual
situation. (In the studied case, Mauritius is located in the east longitude and south latitude, Southern Hemisphere.)
Importing the Data
Descriptions of the options:
1. Datum: You should make a selection in the drop-down list after Datum if Datum is selected.
Select the proper item in the drop-down list after Datum, according to the attribute of the
map that is used.

2. Ellipsoid: You should make a selection in the drop-down list after Ellipsoid if Ellipsoid is selected.
Select the proper item in the drop-down list after Ellipsoid, according to the attribute of the map
that is used.

3. Longitude

4. Latitude

5. Use: Select Datum or Ellipsoid.

6. Grid Coordinate System: Generally, Universal Transverse Mercator (UTM) is selected.

7. Seconds Format: Generally, Nearest 0.01 Second is selected. (This item does not affect the
calculation and the final result.)

8. Allow Non Standard UTM Zones

Importing the Data
The Pathloss software supports various ellipsoid definitions and projection
modes.

Projection modes: Approximately 10 projection modes, such as UTM,

Gausss Kruger, Gauss Conformal (south Africa), New
Zealand Gird, are supported.

Ellipsoid definitions: More than 100 ellipsoid definitions, such as WGS1984,

WGS1972, GRS80, Voirol1960, Massawa, Airy1983, and
Mahe19871, are supported.
Importing the Data
The maps used in the radio network planning all adopt the UTM projection mode.

The basic contents of the UTM are as follows: heights, clutter,

vectors.
The projection.txt file in the heights folder includes the
information of the digital map, such as the ellipsoid, time zone,
projection mode and range.
For example
GRS-1980: ellipsoid definition
29: time zone information of the digital map, that is, Time
Zone 29
UTM: projection mode of the map
0.0-9.0 500000.0 0.0: range of the map

The maps used in the radio network planning mostly adopt the
ellipsoid definitions WGS1984 and GRS1980, and the UTM
projection mode.
Importing the Data
Map Projection
The map projection can exhibit the curved earth surface on a flat
surface by using the specific mathematics method, according to a
certain algorithm, and thus establish mapping relations between the
points on the earth surface and the points on the flat surface. When the
ellipsoid of the earth is projected on a flat surface, the distortion will
occur. According to the shape of the projection plane, the map
projection is classified into azimuth projection, cylindrical projection,
and conical projection. According to the projection distortion property,
the map projection is classified into conformal projection, equivalent
projection, and equidistant projection.
Reference Ellipsoid
As the internal substances of the earth are distributed unevenly
and the earth surface rolls, the datum cannot be used as the
calculation plane of the measurement result. In this case, a
rotating ellipsoid that is similar to the earth is usually selected and
is expressed in the mathematical way to replace the datum. The
ellipsoid is the basis for measurement and map drawing. The
rotating ellipsoid that is in best accordance with the datum of the
local area (a nation or several nations) is called the reference
ellipsoids, such as GRS80, Krassovsky, and WGS84.
 Importing the Data
Universal Transverse Mercator (UTM)

UTM projection is a conformal, secant, and cylindrical projection. The cylinder intersects the
earth at the two circles of equal altitudes: south altitude 80 degrees and north altitude 84
degrees. After the projection, distortion does not occur to the two intersected longitudes. The
ratio of the two longitudes to the central meridian is 0.9996. The UTM projection is created for
the world war. In 1948, the U.S.A completed the calculation of this universe projection
system. The projection azimuth is not distorted, the central meridian is a straight line and is
the symmetry axis of the projection.
In UTM, earth is divided into 60 zones limited by west longitude 180 degrees, spanning six
degrees of longitude each from the west to the east. UTM is a widely used projection mode.
The satellite image of China often adopts the UTM projection mode.
Importing the Data
 Choose Configure > Terrain Database from the menu of the
Pathloss. In the displayed Configure Terrain Database dialog box,
select Odyssey - UTM under Primary.
Importing the Data
• Click Setup Primary. In the displayed Odyssey - UTM dialog box, select Use special UTM zone, and enter the time zone number
plus N or S in the box. ("N" represents the Northern Hemisphere, and "S" represents the Southern Hemisphere. If you do not enter N
or S, it is set to N by default. In the case of Mauritius, you should enter 40S.) If the map contains the information of buildings, select
Embedded building data. If the map covers regions that are located in several time zones, you can select Use standard UTM
zones in index.
Importing the Data
Descriptions of the options:
1. Use standard UTM zones in index: When the map covers regions that are
located in several time zones, you should select this item.
2. Use specified index file: When the time zone file is available, you can select this
item. In this case, you should specify the index file that contains the data of the
time zone.
3. Use specified UTM zone: When you select this item, enter the accurate time
zone number and the letter that indicates the hemisphere where the region is
located, for example, 40S
4. Embedded building data: When the map contains the information of buildings,
select this item. When the planned links are located in cities, this item has a great
impact.
Importing the Data
 Click Set Directory to specify the directory of the map. In the example, the path is as follows:
D:\Microwave Planning Design Software Training\20-new Mauritius\height. Note that you should select
the Heights folder in the directory of the digital map. Click Index, and choose Files > Import List in
the displayed Odyssey - UTM window. The Define Fields dialog box is displayed as follows:
Importing the Data
• Click Planet, and the format of the imported data is changed to Planet. In UTM zone, enter the time
zone number plus N or S. Then click OK, select the Index.txt file, and click OK. The map information
list is imported. Choose Files > Close in the Odyssey - UTM window. Click Close and then click OK.
• Descriptions of the preceding parameters:
Edge units: generally expressed in meters
Byte order: SPARC or INTEL
Bottom up: This item determines whether the map starts from the southwestern corner or from the
northwestern corner. If the imported map is upside down, you need to adjust this item.
Importing the Data
• Importing the Data in the Format of CSV
Importing the data of a single layer
Choose Module > Network > Site Data > Site List > Import > Site Text File from the menu of the Pathloss, and the Import Text File dialog
box is displayed.

 After you determine the related items in the Import Text File dialog box, click Import.
Select the data to be imported (final data format: *.CSV), click Open, and then click
Import. Click Close when the process is complete.
Importing the Data
• Choose Files > Save (in the format of *.gr4) > Site Data > Create Background. The background file is
created.
 Importing the Data
• The background files may not be created when the Pathloss is used. The
possible causes are as follows:
1. The table heading in the saved *.CSV file is not deleted.
2. The path of the map is incorrectly set.
3. The geographical location is incorrectly set.
4. The file is not saved as required, that is, you should choose Files >
Save to save the file in the format of *.gr4.
Importing the Data
Importing the data of multiple layers

• Click Start, and choose Program > Pathloss 4.0 to run the software.
• Choose Module > Network > Configure > Terrain Database, and
the Configure Terrain Database dialog box is displayed.
• Setting the layers: Select Layers to determine the layer where the site
is located, and then click OK.
• Modifying the legends of sites in batches: Choose Defaults > Site
Legend.
• Choose Site Data > Site List > Import > Site Text File, and the
Import Text File dialog box is displayed. After you set the attributes of
the site in the dialog box, click Import to select the data to be
imported (in the format of *.CSV). Click Import, and then click Close
when the process is complete.
Contents

 Overview

 Importing the Data

 Pre-Planning Routes

 Outputting the

Information
Pre-Planning Routes
1. Read through the contents on network, transmission and line construction in the
tender document and digest these contents. Sort out the required information.
2. If the clauses that are required for the network planning but are not specified in the
tender document, communicate with the operator and clarify the doubts.
3. Fully understand the bidding strategies of the project team.
4. Determine the required conditions for pre-planning the microwave transmission
routes, based on the requirements of the tender document, the conclusion reached
after the communication with the project team, and the output of the radio network
planning. These required conditions are described as follows:
• Bidding strategies of the project team
• KPIs
• Transmission modes of the backbone network (network between cities)
• Selected microwave products
• Maximum antenna heights
• Adopted protection modes
 Pre-Planning Routes
• Risk factor of the microwave BOQ
• Frequencies
• Geographical location of the nation, that is, the hemisphere, longitude, and latitude
where the nation is located.
• Location of each BTS and the requirement of each BTS for the transmission capacity
• Location of each BSC and the requirement of each BSC for the transmission capacity
• Subordinating relations between BSCs and BTSs
5. When the Pathloss software is used to pre-plan the microwave transmission routes,
the following aspects are involved:
• Divide the work of personnel involved in the project microwave planning and design
and making out the plan.
• Produce the project-level microwave transmission distance calculation table.
• Determine the graphic example of the project-level microwave planning and design
and outputting the format.
• Determine the microwave network topology to design the network at different layers,
that is, backbone layer, convergence layer, and access layer. Increase the distance of
routes in the SDH backbone network to a proper length to decrease the number of
SDH microwave hops, choosing curved profiles, and capitalizing on the local terrain
condition.
 Pre-Planning Routes
• Network Configuration
SDH (large-capacity microwave: STM-1) 4xE1
PDH (small-capacity microwave: 4xE1, 8xE1, 16xE1)

E1
1+1 1E1
1E1

4x
2xE
2xE
BSC 11
16xE1
4xE1

8x

E1
E1

4x
4xE1
4xE1 4xE1
4xE1 2xE1
2xE1 1xE1
1xE1

4xE
1 1xE1
1xE1

2xE1
2xE1
Pre-Planning Routes
Start

Connecting the BSC at the root

node to the nearest site

(1) Check if there is the site with NO

no link configured

YES
Click on the connection line

Terrain Data

Operations

Generate Profile

Close Adding a
Relay Site

Module

Antenna Heights

Calculate to adjust the antenna heights

at two ends

Check if the line-of- NO

sight Transmissions
Between two sites
is available

YES
Network

Flow chart 1 YES

END
Pre-Planning Routes
Procedures for Configuring a Link
 Connect the BSC to a nearest site, and click on the
connection line. Choose Terrain Data > Operations >
Generate Profile.
 In the displayed Generate Profile dialog box, click Generate
and then click Close. Choose Module > Antenna Heights,
and click Calculate (check if the line-of-sight transmission
between the two sites is available).
 Choose Module > Network, and then click Yes.
Pre-Planning Routes
• Drag the mouse to connect Site38 and Site40. Click on the connection line, and
select Summary. Based on the data in Calculated Distance (km), enter the proper
value in Frequency. This hop of link adopts the central frequency point 12996 MHz
of the 13 GHz frequency band.
Pre-Planning Routes
• Choose Module > Terrain Data > Operations > Generate Profile.
Pre-Planning Routes
• Click Generate in the Generate Profile dialog box, and then click Close. Double-
click the blank area under Structure, and then select Range of Structures. Set the
height of the structure (in the example, a tree of 15 meters).

 Select any point on the profile, and you can modify the related parameters, for
example, distance, elevation, structure, scale and ground.
Pre-Planning Routes
• Choose Module > Antenna Heights, and then click .
Pre-Planning Routes
• Choose Module > Print Profile.

220

200

180

160
E lev ation ( m )

140

120

100

80

60

40

20
0 1 2 3 4 5 6 7 8 9
Path leng th (9.11 km)
Site38 Frequency (MHz) = 12996.0 Site40
Latitude 20 11 15.36 S K = 1.33, 0.67 Latitude 20 08 52.08 S
Long itude 057 43 03.36 E %F1 = 100.00, 60.00 Longitude 057 38 28.68 E
Azimuth 298.90 Azimuth 118.93
Elevation 40 m ASL Elevation 170 m ASL
Antenna CL 28.5 m AGL Antenna CL 29.8 m AGL

十月 18 07
Pre-Planning Routes
Operations for the Sites Between Which the Line-of-Sight Transmission Is not Available: Adding a
Relay Site
Determine the
location of the relay
site to be added

Site Data

Add Site

Click on the location

of the relay site to be
added

Add Site

Enter the name of

the relay site

OK

Flow chart 2 Flow chartFlow

2 chart 2
Flow chart 1-(1)
 Pre-Planning Routes
• Deleting a Relay Site
Choose Site Data > Site List, and select the site to be deleted. Choose Edit > Delete >
Import > Close.
• Labeling a Link
Labeling a link by default (labeling the site distance only)
Right-click on a link and select Label, and the Label dialog box is displayed. Select
Distance, and deselect Do not draw. Enter the information of the link in the blank of the
dialog box. You can also adjust the font size and position of the characters. After the
process is complete, click OK.
Labeling a link in a customized way (labeling any information on the link)
Right-click on a link and select Label, and the Label dialog box is displayed. Deselect Do
not draw. Enter the information of the link in the blank of the dialog box. You can also
adjust the font size and position of the characters. After the process is complete, click
OK.
Pre-Planning Routes
• Labeling a Link by Default (Labeling the Site Distance Only)
Pre-Planning Routes
• Labeling a Link in a Customized Way (Labeling Any Information on the Link)
Contents

 Overview

 Importing the Data

 Pre-Planning Routes

 Outputting the

Information
Outputting the Information
Outputting
Outputtingthe
the
terrain diagram
terrain diagram

Outputting
Outputtingthethe
profile diagram
profile diagram
between
betweensites
sites

Outputting
Outputtingthe
the
antenna height
antenna height
and
andsite
sitedistance
distance

Outputting
Outputtingthe
thenetworking
networking
diagram
diagram as a PDFdocument
as a PDF document
Outputting the Information
• Choose Module > Network > Print > Copy from the menu of the Pathloss.
Paste the terrain diagram in the Word and save it in the format of *.doc.
Outputting the Information
• Outputting the Profile Diagram of a Single Link
Click on the link whose profile diagram is to be output between two sites, and choose Terrain
Data > Module > Print Profile > Print > Copy from the menu of the Pathloss. Paste the profile
diagram in the Word and save it in the format of *.doc.

220

200

180

160
E l e v a ti o n ( m )

140

120

100

80

60

40

20
0 1 2 3 4 5 6 7 8 9
Path length (9.11 km)
Site38 Frequency (MHz) = 12996.0 Site40
Latitude 20 11 15.36 S K = 1.33, 0.67 Latitude 20 08 52.08 S
Long itude 057 43 03.36 E %F1 = 100.00, 60.00 Long itude 057 38 28.68 E
Azimuth 298.90 Azimuth 118.93
Elevation 40 m ASL Elevation 170 m ASL
Antenna CL 28.5 m AGL Antenna CL 29.8 m AGL

十月 18 07
Outputting the Information
• Outputting the Profile Diagrams of Multiple Links in Batches

 Two software programs should be installed: Adobe Acrobat 5.0 and

pdfprinter.
 Double-click Pathloss 4.0. Choose Module > Print Profile > Batch
Print, and then click on a certain link. Press Ctrl+A to select all
links, and then click Open. Enter the names of these files, and save
them in the format of *.PDF. (The number of files is determined by
the number of links. In this case, the PDF documents containing the
profile diagrams are generated in batches.)
 Double-click on a certain link whose PDF document containing the
profile diagram was created previously. Select the PDF document,
and select and insert all the other created PDF documents
containing the profile diagrams of other links. Click OK. In this way,
you can combine multiple PDF documents into one PDF document.
Outputting the Information
• Outputting the Antenna Height and Site Distance
Choose Site Data > Site List > Reports > CSV link list-microwave. Select the site information to be output, and then
click OK. In this case, the report is saved as a CSV file. You should open it in the Excel and save it in the format of *xls.
Outputting the Information
Outputting the Information
• The networking diagram is output as a PDF document. Do as follows: Click
Printer Setup, and select Acrobat PDFWrite in the Printer Setup dialog box.
Set the size of the paper, and then click Properties.
Outputting the Information
Outputting the Information
 Choose Print > Print to save the file in the format of *.pdf, and then click Save.