21FL91

SERVICE MANUAL
SX2U321FL91//

COLOR TELEVISION
Chassis No. GA-2

MODEL 21FL91
In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.

CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2
» LOCATION OF USER'S CONTROL ..................................................................................................... 4
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 5
» SERVICE MODE .................................................................................................................................. 6
» ADJUSTMENT METHOD ................................................................................................................... 11
» CHASSIS LAYOUT ............................................................................................................................. 26
» BLOCK DIAGRAM .............................................................................................................................. 27
» SCHEMATIC DIAGRAMS ................................................................................................................... 33
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 38
» REPLACEMENT PARTS LIST ............................................................................................................ 42
» PACKING OF THE SET ...................................................................................................................... 48

ELECTRICAL SPECIFICATIONS
POWER INPUT ....................................... AC 110~220 V, 50/60 Hz SPEAKER
POWER RATING .................................................................... 95W SIZE ................................................................... 12 x 5 cm, 2pcs
PICTURE SIZE .......................................... 1,239 cm2 (192sq inch) VOICE COIL IMPEDANCE ............................. 16 ohm at 400 Hz
CONVERGENCE ............................................................. Magnetic ANTENNA INPUT IMPEDANCE
SWEEP DEFLECTION .................................................... Magnetic VHF/UHF ..................................................... 75 ohm Unbalanced
FOCUS ............................................... Hi-Bi-Potential Electrostatic TUNING RANGES
INTERMEDIATE FREQUENCIES VHF-Channels ............................................................... 2 thru 13
Picture IF Carrier Frequency ..................................... 45.75 MHz UHF-Channels ............................................................ 14 thru 69
Sound IF Carrier Frequency ...................................... 41.25 MHz CATV Channels ........................................................... 1 thru 125
Color Sub-Carrier Frequency .................................... 42.17 MHz (EIA, Channel Plan U.S.A.)
(Nominal)
AUDIO POWER Specifications are subject to change without
OUTPUT RATING ........................................ 3.0 W(RMS) x 2pcs prior notice.

This document has been published to be used for after

SHARP CORPORATION sales service only.
The contents are subject to change without notice.
21FL91

IMPORTANT SERVICE SAFETY PRECAUTION

Ë Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:

WARNING X-RADIATION AND HIGH VOLTAGE LIMITS

1. For continued safety, no modification of any circuit 1. Be sure all service personnel are aware of the
should be attempted. procedures and instructions covering X-radiation.
2. Disconnect AC power before servicing. The only potential source of X-ray in current solid
3. Semiconductor heat sinks are potential shock state TV receivers is the picture tube. However, the
hazards when the chassis is operating. picture tube does not emit measurable X-Ray
4. The chassis in this receiver has two ground systems radiation, if the high voltage is as specified in the
which are separated by insulating material. The non- "High Voltage Check" instructions.
isolated (hot) ground system is for the B+ voltage It is only when high voltage is excessive that X-
regulator circuit and the horizontal output circuit. The radiation is capable of penetrating the shell of the
isolated ground system is for the low B+ DC voltages picture tube including the lead in the glass material.
and the secondary circuit of the high voltage The important precaution is to keep the high voltage
transformer. below the maximum level specified.
To prevent electrical shock use an isolation 2. It is essential that servicemen have available at all
transformer between the line cord and power times an accurate high voltage meter.
receptacle, when servicing this chassis. The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
SERVICING OF HIGH VOLTAGE SYSTEM there is no possibility of an X-radiation problem.
AND PICTURE TUBE Every time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
When servicing the high voltage system, with a meter to be certain that the high voltage does
remove the static charge by connecting a not exceed the specified value and that it is regulating
10k ohm resistor in series with an insulated correctly.
5. Do not use a picture tube other than that specified
wire (such as a test probe) between the pic- or make unrecommended circuit modifications to the
ture tube ground and the anode lead. (AC high voltage circuitry.
line cord should be disconnected from AC 6. W h e n t r o u b l e s h o o t i n g a n d t a k i n g t e s t
outlet.) measurements on a receiver with excessive high
voltage, avoid being unnecessarily close to the
1. Picture tube in this receiver employs integral receiver.
implosion protection. Do not operate the receiver longer than is necessary
2. Replace with tube of the same type number for to locate the cause of excessive voltage.
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.

2
 21FL91

IMPORTANT SERVICE SAFETY PRECAUTION

(Continued)

BEFORE RETURNING THE RECEIVER • Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
(Fire & Shock Hazard) cabinet, screw heads, knobs and control shafts,
Before returning the receiver to the user, perform escutcheon, etc.) and measure the AC voltage drop
the following safety checks. across the resistor.
AII checks must be repeated with the AC line cord
1. Inspect all lead dress to make certain that leads are plug connection reversed. (If necessary, a non-
not pinched or that hardware is not lodged between polarized adapter plug must be used only for the
the chassis and other metal parts in the receiver. purpose of completing these check.)
2. Inspect all protective devices such as non-metallic Any current measured must not exceed 0.5 milliamp.
control knobs, insulating materials, cabinet backs, Any measurements not within the limits outlined
adjustment and compartment covers or shields, above indicate of a potential shock hazard and
isolation resistor-capacity networks, mechanical corrective action must be taken before returning the
insulators, etc. instrument to the customer.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 110~220 volt AC
outlet, (Do not use an isolation transformer for this
test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to earth ground. 1.5k ohm
• Use an AC voltmeter having with 5000 ohm per volt, 10W
or higher, sensitivity to measure the AC voltage drop
across the resistor.

0.15 F
TEST PROBE

TO EXPOSED
METAL PARTS CONNECT TO
KNOWN EARTH
GROUND

123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
SAFETY NOTICE
Many electrical and mechanical parts in television For continued protection, replacement parts must be
receivers have special safety-related characteristics. identical to those used in the original circuit. The use of
These characteristics are often not evident from visual substitute replacement parts which do not have the same
inspection, nor can protection afforded by them be safety characteristics as the factory recommended
necessarily increased by using replacement components replacement parts shown in this service manual, may
rated for higher voltage, wattage, etc. create shock, fire, X-radiation or other hazards.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

3
21FL91

LOCATION OF USER'S CONTROL

4
 21FL91

INSTALLATION AND SERVICE INSTRUCTIONS

Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.

CIRCUIT PROTECTION HIGH VOLTAGE CHECK

The receiver is protected by a 3.15A fuse (F701), High voltage is not adjustable but must be checked
mounted on PWB-A, wired into one side of the AC to verify that the receiver is operating within safe
line input. and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
1. Connect an accurate high voltage meter between
After service has been performed on the horizontal ground and anode of picture tube.
deflection system, high voltage system, B+ system, 2. Operate receiver for at least 15 minutes at 110~220V
test the X-Radiation protection circuit to ascertain AC line voltage, with a strong air signal or a properly
proper operation as follows: tuned in test signal.
3. Enter the service mode and set Y-mute ON by using
1. Apply 110~220V AC using a variac transformer for Service R/C.
accurate input voltage. 4. The voltage should be approximately 28.7kV (at zero
2. Allow for warm up and adjust all customer controls beam).
for normal picture and sound. If a correct reading cannot be obtained, check circuitry
3. Receive a good local channel. for malfunctioning components. After the voltage test,
4. Connect a digital voltmeter to TP653 and make sure make Y-mute off to the normal mode.
that the voltmeter reads 18.9 ±1.1V.
5. Apply external 24.5V DC at TP653 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.

5
21FL91

SERVICE MODE
Service Mode Overview
1. Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset.
2. Service mode is cleared by entering SERVICE key command during service mode.
3. If key input port (SERVICE) input is LOW, then it is in service mode.
4. During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE is disabled.
5. Service mode can be switched to 4 modes as follows by key input MENU;

Adjustment mode

First mode of service mode when SERVICE key is

Setting mode pressed.

Check mode

Option mode First mode of service mode when local key

CH-UP + VOL-DOWN is pressed after MCU reset.

6. AFT processing is disabled during service mode. PLL setting data is set to fo data.
7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively
in service mode. Energy Save is off.
8. Sleep timer, View timer and Off timer are inactivated in Service mode.
9. Sound is muting in service mode except at Adjustment Items V20, M01, M03, M04, M05, and M06.

6
 21FL91

Adjustment Mode Items

No. Item Name IC Register Range Default
V01 SUB-PICTURE 1 Chip CONTRAST 0~127 127
V02 SUB-TINT 1 Chip TINT 0~127 64
V03 SUB-COLOR 1 Chip COLOR 0~127 64
V04 SUB-BRIGHT 1 Chip BRIGHT 0~255 128
V05 SUB-SHARP 1 Chip VIDEO-TONE 0~63 32
V06 V-SHIFT 1 Chip V-SHIFT 0~7 4
V07 H-SHIFT 1 Chip H-PHASE 0~31 16
V08 RF-AGC 1 Chip RF-Delay 0~127 127
V09 V-SIZE 1 Chip V-SIZE 0~63 32
V10 PIF-VCO 1 Chip VIF-VCO 0~63 32
V11 R-CUTOFF 1 Chip R-CUTOFF 0~255 127
V12 G-CUTOFF 1 Chip G-CUTOFF 0~255 127
V13 B-CUTOFF 1 Chip B-CUTOFF 0~255 127
V14 R-DRIVE 1 Chip R-DRIVE 0~127 64
V15 B-DRIVE 1 Chip B-DRIVE 0~127 64
V16 SUB-COLOR(YUV) 1 Chip COLOR 0~127 64
V17 SUB-TINT(YUV) 1 Chip BASEBAND-TINT 0~127 64
V18 CC-POS MICON 0~255 32
V19 (Vertical mode) 1 Chip V-MUTE,SERVICE 0, 1, 2 0
V20 SUB-VOL 1 Chip A-ATT 0~127 127
V21 H-VCO 1 Chip H-VCO 0~7 4
M01 MTS-ATT MTS ATT 0~15 10
M02 MTS-VCO MTS VCO 0~63 32
M03 MTS-FILTER MTS FILTER 0~63 28
M04 MTS-WIDEBAND MTS WIDEBAND 0~63 27
M05 MTS-SPECTRAL MTS SPECTRAL 0~63 32
M06 SUB-VOL MTS VOL 0~63 63

7
21FL91

Ë SELF ADJUSTMENT
H-VCO
1. When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.
2. H-FREE(1chip) is set to 1.
3. H-OUT is set by intelligent monitor output.
4. IM input is set as TIM input.
5. H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.
6. When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.
7. H-FREE(1chip), intelligent monitor output and IM input mode are recovered.

RF-AGC
1. When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.
2. AGC-OUT is set by intelligent monitor output.
3. IM input is set as AD input.
4. By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the
maximum setting value.
5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.
6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.
7. Intelligent monitor output and IM input mode are recovered.

PIF-VCO
1. When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.
2. VIF-DEF(1chip) is set to 1.
3. AFC is set by intelligent monitor output.
4. IM input is set as AD input.
5. VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V.
6. When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.
7. VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.

MTS-FILTER
Adjustment is performed in the center of the range when FILTER status is OK.
1. If data is changed from 0 to 63, point where NG → OK is A and point where OK → NG is B.
2. If data is changed from 63 to 0, point where NG → OK is C and point where OK → NG is D.
3. (A+B+C+D)/4 is the adjustment point.

8
 21FL91

Setting Mode Items

No. Item Name IC Register Range Default
F01 VideoTone-Gain (TV) 1chip V-TONE 0/1 0
F02 VideoTone-Gain (AV) 1chip V-TONE 0/1 0
F03 VideoTone-Gain(YUV) 1chip V-TONE 0/1 0
F04 ABCL 1chip ABCL 0/1 0
F05 BS 1chip BS-OFF 0/1 0
F06 ABCL-G 1chip ABCL-G 0/1 0
F07 SHP-AV OFFSET VIDEO-TONE(OFFSET) -16~+16 0
F08 SHP-YUV OFFSET VIDEO-TONE(OFFSET) -16~+16 0
F09 RGB-CLIP 1chip ExtRGB-Clip 0/1 0
F10 E-SAVE OFFSET CONTRAST(OFFSET) 0~63 30
F11 FAO-VOL 1chip A-ATT 0~127 120
F12 PIF-G 1chip VIF-GAIN 0~7 4
F13 Y-DELAY(TV) 1chip Y-Delay 0~7 0
F14 Y-DELAY(AV) 1chip Y-Delay 0~7 0
F15 Y-DELAY(YUV) 1chip Y-Delay 0~7 0
F16 TINT-AV OFFSET TINT(OFFSET) -32~+32 0
F17 COL-AV OFFSET COLOR(OFFSET) -32~+32 0
F18 R-DRI(R2) OFFSET R-DRI(OFFSET) -32~+32 0
F19 R-DRI(R) OFFSET R-DRI(OFFSET) -32~+32 0
F20 R-DRI(B) OFFSET R-DRI(OFFSET) -32 ~+32 0
F21 B-DRI(R2) OFFSET B-DRI(OFFSET) -32~+32 0
F22 B-DRI(R) OFFSET B-DRI(OFFSET) -32~+32 0
F23 B-DRI(B) OFFSET B-DRI(OFFSET) -32~+32 0
F24 V-FREE 1chip V-FREE 0/1 0
F25 GAMMA 1chip GAMMA 0~3 0
F26 TRAP(TV) 1chip TRAP-FINE 0~3 2
F27 TRAP(AV) 1chip TRAP-FINE 0~3 2
F28 H-FREE 1chip H-FREE 0/1 0
F29 1W(TV) 1chip V.Window 0/1 0
F30 1W(AV) 1chip V.Window 0/1 0
F31 YLPF 1chip YSW-LPF 0/1 1
F32 BS-D 1chip BS-DISCHARGE 0~3 0
F33 BS-C 1chip BS-CHARGE 0~3 0
F34 SL(TV) 1chip S-SLICE DOWN 0~3 0
F35 SL(AV) 1chip S-SLICE DOWN 0~3 0
F36 SL(YUV) 1chip S-SLICE DOWN 0~3 0
F37 AFC2 1chip AFC2-G 0/1 0
F38 VD(TV) 1chip Vsync-Det 0/1 0
F39 VD(AV) 1chip Vsync-Det 0/1 0
F40 AS(TV) 1chip Auto-Slice 0/1 0
F41 AS(AV) 1chip Auto-Slice 0/1 0
F42 AS(YUV) 1chip Auto-Slice 0/1 0
F43 FBP(TV) 1chip FBP Vth 0/1 0
F44 FBP(AV) 1chip FBP Vth 0/1 0
F45 FBP(YUV) 1chip FBP Vth 0/1 0
F46 C.Clip Level 1chip C.Clip Level 0/1 0
F47 PSW MTS PSW 0/1 0
F48 FAO-VOL MTS VOL 0~63 60
F49 CP PLL CP 0/1 0
F50 CC LEVEL MICON 0/1 0
F51 OSD POS MICON 0/1 0
F52 OFFSET-ADJ-COL 1 chip COLOR -32~32 0
F53 OFFSET-ADJ-TINT 1 chip TINT -32~32 0
F54 OFFSET-ADJ-TINT-YUV 1 chip BASEBAND-TINT -32~32 0

9
21FL91

Option Mode Items

No ITEM 0 1 DEFAULT
O01 DEM0 Without DEMO With DEMO 1
O02 DOWNLOAD Without V-CHIP OP With V-CHIP OP 1
O03 V-CHIP Without V-CHIP With V-CHIP 1
O04 SPEAKER Without SPEAKER With SPEAKER 1
O05 FAO Without FAO With FAO 1
O06 P.PREF Without P.PREF With P.PREF 1
O07 UNIV+ Without UNIV+ With UINIV+ 1
O08 VIEW TIMER Without VIEW TIMER With VIEW TIMER 1
O09 EZ-SETUP EZ-SETUP AUTO PRESET 1
O10 PON-CH Without POWER-ON With POWER-ON 1
O11 FAV-COL FAV-COL COL-TEMP 1
O12 COMPONENT Without COMPONENT With COMPONENT 1
O13 AV Without AV With AV 1
O14 AV2 AV1 system AV2 system 1
O15 MTS Without MTS With MTS 1
O16 TONE-CTRL Without S-ADJ With S-ADJ 1
O17 AUTO-OFF Without AUTO-OFF With AUTO-OFF 1
O18 INIT-LANG ENGLISH SPANISH 0
O19 SETUP-FLAG NO SETUP AUTO SETUP 1
3: Display "FRONT A/V INPUTS" and
"REAR A/V INPUTS" in DEMO mode.
O20 FR.AV (Front, 2: Display "FRONT A/V INPUTS" only in 2
DEMO mode.
Rear AV)
1: Display "REAR A/V INPUTS" only in
DEMO mode.
0: No display of above lines in DEMO mode.

Check Mode
Micron mask version, software version and ROM correction function status are displayed in check mode.

10
 21FL91

ADJUSTMENT METHOD
Caution: to get into the service mode, one of the ways is press direct key for service items. the other ways
is short the main chassis JA309 and JA402

There is three stage of Service Mode data

First stage data from V01 ~ M06
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F54
to go into third stage of service mode data, press MENU key twice
Third stage data from 001 ~ 020

Below is the contents of these data

First Stage

Data Service Mode Function Range Default Data

V01 SUB-PICTURE CONTRAST 0~127 127
V02 SUB-TINT TINT 0~127 64
V03 SUB-COLOR COLOR 0~127 64
V04 SUB-BRIGHT BRIGHT 0~255 128
V05 SUB-SHARP VIDEO-TONE 0~63 32
V06 V-SHIFT V-SHIFT 0~7 4
V07 H-SHIFT H-PHASE 0~31 16
V08 RF-AGC RF-DELAY 0~127 127
V09 V-SIZE V-SIZE 0~63 32
V10 PIF-VCO VIF-VCO 0~63 32
V11 R-CUTOFF R-CUTOFF 0~255 127
V12 G-CUTOFF G-CUTOFF 0~255 127
V13 B-CUTOFF B-CUTOFF 0~255 127
V14 R-DRIVE R-DRIVE 0~127 64
V15 B-DRIVE B-DRIVE 0~127 64
V16 SUB-COLOR(YUV) COLOR 0~127 64
V17 SUB-TINT(YUV) BASEBAND-TINT 0~127 64
V18 CC-POS CC-POSITION 0~255 32
V19 SCREEN CUT OFF CUT OFF 0
V20 SUB-VOL A-ATT 0~127 127
V21 H-VCO H-VCO 0~7 4
M01 MTS-ATT ATT (MTS) 0~15 10
M02 MTS-VCO VCO (MTS) 0~63 32
M03 MTS-FILTER FILTER (MTS) 0~63 28
M04 MTS-WIDEBAND WIDEBAND (MTS) 0~63 27
M05 MTS-SPECTRAL SPECTRAL (MTS) 0~63 32
M06 SUB-VOL VOL (MTS) 0~63 63

Auto Adjustment Item

1. H-VCO (Currently need manual adj)
2. RF-AGC
3. PIF-VCO
4. MTS-FILTER

11
21FL91

Second Stage
Data Service Mode Function Range Default Data
F01 VIDEO TONE -GAIN (TV) V-TONE 0/1 0
F02 VIDEO TONE -GAIN (AV V-TONE 0/1 0
F03 VIDEO TONE -GAIN(YUV) V-TONE 0/1 0
F04 ABCL ABCL 0/1 0
F05 BS BS-OFF 0/1 0
F06 ABCL-G ABCL-G 0/1 0
F07 SHP-AV VIDEO-TONE(OFFSET) -16~+16 0
F08 SHP-YUV VIDEO-TONE(OFFSET) -16~+16 0
F09 SHP-CLIP EXTRGB-CLIP 0/1 0
F10 E-SAVE CONTRAST(OFFSET) 0~63 30
F11 FAO-VOL A-ATT 0~127 120
F12 PIF-G VIF-GAIN 0~7 4
F13 Y-DELAY(TV) Y-DELAY 0~7 0
F14 Y-DELAY(AV) Y-DELAY 0~7 0
F15 Y-DELAY(YUV) Y-DELAY 0~7 0
F16 TINT-AV TINT(OFFSET) -32~+32 0
F17 COL-AV COLOR(OFFSET) -32~+32 0
F18 R-DRI(R2) R-DRI(OFFSET) -32~+32 0
F19 R-DRI( R) R-DRI(OFFSET) -32~+32 0
F20 R-DRI(B) R-DRI(OFFSET) -32~+32 0
F21 B-DRI(R2) B-DRI(OFFSET) -32~+32 0
F22 B-DRI( R) B-DRI(OFFSET) -32~+32 0
F23 B-DRI(B) B-DRI(OFFSET) -32~+32 0
F24 V-FREE V-FREE 0/1 0
F25 GAMMA GAMMA 0~3 0
F26 TRAP(TV) TRAP-FINE 0~3 2
F27 TRAP(AV) TRAP-FINE 0~3 2
F28 H-FREE H-FREE 0/1 0
F29 1W(TV) V.WINDOW 0/1 0
F30 1W(AV) V.WINDOW 0/1 0
F31 YLPF YSW-LPF 0/1 1
F32 BS-D BS-DISCHARGE 0~3 0
F33 BS-C BS-CHARGE 0~3 0
F34 SL(TV) S-SLICE DOWN 0~3 0
F35 SL(AV) S-SLICE DOWN 0~3 0
F36 SL(YUV) S-SLICE DOWN 0~3 0
F37 AFC2 AFC2-G 0/1 0
F38 VD(TV) VSYNC-DET 0/1 0
F39 VD(AV) VSYNC-DET 0/1 0
F40 AS(TV) AUTO-SLICE 0/1 0
F41 AS(AV) AUTO-SLICE 0/1 0
F42 AS(YUV) AUTO-SLICE 0/1 0
F43 FBP(TV) FBP VTH 0/1 0
F44 FBP(AV) FBP VTH 0/1 0
F45 FBP(YUV) FBP VTH 0/1 0
F46 C.CLIP LEVEL C.CLIP LEVEL 0/1 0
F47 PSW PSW 0/1 0
F48 FAO-VOL VOL 0~63 60
F49 CP CHARGE PUMP 0/1 0
F50 CC LEVEL CC LEVEL 0/1 0
F51 OSD POS OSD POS 0/1 0
F52 COL OFFSET (SUR → NOR) 0
F53 TINT OFFSET (SUR → NOR) 0
F54 TING-YUV TINT-YUV(OFFSET) 0

12
 21FL91

Third Stage
Data Service Mode DATA="0" DATA="1" Default Data
001 DEMO DEMO DISABLE ON 1
002 DOWNLOAD V-CHIP OP DISABLE ON 1
003 V-CHIP V-CHIP DISABLE ON 1
004 SPEAKER SPEAKER DISABLE ON 1
005 FAO FAO DISABLE ON 1
006 P.PREF P.REF DISABLE ON 1
007 UNIV+ UNIV+ DISABLE ON 1
008 VIEW TIMER VIEW TIMER DISABLE ON 1
009 EZ-SETUP EZ-SETUP AUTO PRESET 1
010 *PON-CH POWER-ON DISABLE ON 1
011 FAV-COL FAV-COL COL-TEMP 1
012 COMPONENT COMPONENT DISABLE ON 1
013 AV AV DISABLE ON 1
014 AV2 AV2 DISABLE ON 1
015 MTS MTS DISABLE ON 1
016 TONE-CTRL S-ADJ DISABLE ON 1
017 AUTO-OFF AUTO-OFF DISABLE ON 1
018 INIT-LANG ENGLISH SPANISH 0
019 SETUP-FLAG NO SET UP AUTO SET UP 1
020 AV-FR "0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT 2
*
**POWER ON BY CH-UP/CH-DOWN KEY

13
 21FL91

ADJUSTMENT ADJUSTMENT
OPTION SET UP BUS SET UP
ITEM ITEM
ADJUSTMENT ADJUSTMENT
REFER AS BELOW STEP RANGE REFER AS BELOW REFER AS BELOW STEP RANGE REFER AS BELOW
POSITION POSITION

CONTROL – CONTROL –

PRE-ADJUST PRE-ADJUST
– –
REQUIREMENT REQUIREMENT

CONTENT – CONTENT –

INPUT INPUT 21FL91

21FL91 CONDITION
CONDITION

OUTPUT OSD CHECKING OUTPUT OSD CHECKING

BUS OPTION FOR THIRD STAGE SERVICE DATA DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
V05 F13 F14 F16 F17 F30 F34 F38 F40 F49 F18
001 002 003 004 005 006 007 008 009 010 FUNCTION
FUNCTION SHARP Y-DL(TV) Y-DL(AV) TINT-AV COL-AV 1W(AV) SL(TV) VD(TV) AS(TV) CP R-D(R2)
DEMO DOWNLOAD V-CHIP SP FAO P.PREF UNIV+ VIEW EZ PON-CH
21FL91 1 0 0 1 1 1 1 1 0 0 21FL91 50 5 2 -7 4 1 1 1 1 1 +8

14
DEF
DEF “0”=DISABLE “1”=ENABLE
ADJUSTMENT ADJUSTMENT
009 → “0”=EZ-SETUP “1”=AUTO PRESET
PROCEDURE PROCEDURE

BUS OPTION FOR THIRD STAGE SERVICE DATA DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
F19 F20 F21 F22 F23 F52 F53 F35 F41 F48 F54
011 012 013 014 015 016 017 018 019 020 FUNCTION
FUNCTION R-D(R) R-D(B) B-D(R2) B-D(R) B-D(B) C-OF TI-OF SL(AV) AS(AV) FAO-VOL TINT-YUV
FAV-COL COMP AV AV2 MTS TONE AUTO LAN SETUP AV-FR 21FL91 +3 -2 -18 -8 +6 +10 +8 1 1 58 -8
21FL91 1 1 1 1 1 1 1 1 1 3

DEF
DEF 011 → ”0”=FAV-COL “1”=COL-TEMP
018 → “0”=ENGLISH “1”=SPANISH
019 → “0”=NO SET UP “1”=AUTO SETUP

14-1 14-2
 ADJUSTMENT ADJUSTMENT
H-POSITION V-SIZE
ITEM ITEM
ADJUSTMENT ADJUSTMENT
V07 STEP RANGE 0-31 V09 STEP RANGE 0~63
POSITION POSITION

CONTROL I2C BUS CONTROL CONTROL I2C CONTROL

PRE-ADJUST PRE-ADJUST
OPTION SET UP, BUS SET UP, CRT-PURITY OPTION SET UP, BUS SET UP, CRT PURITY, V-PHASE, +B ADJUST
REQUIREMENT REQUIREMENT

CONTENT US 4 CH LION HEAD (MONOSCOPE) CONTENT US 4 CH LION HEAD

INPUT INPUT AC 220V

AC 220V, MEXICO MAGNETIC FIELD
CONDITION CONDITION

OUTPUT CONFIRMATION BY CRT SCREEN OUTPUT CONFIRMATION BY CRT SCREEN

1. ADJUST THE V07 BUS DATA TO HAVE A BALANCE POSITION TO SPEC ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS
OF A=B. SPECIFIED BELOW.
2. IF CANNOT MAKE IT TO A=B, ADJ FROM THE BEST POINT SO THAT CAUTION: - PLEASE AGING TV MORE THAN 10 MINUTES BEFORE
B SLIDELY SMALLER THAN A ADJUSTMENT.

15
A B

ADJUSTMENT ADJUSTMENT
PROCEDURE PROCEDURE

[CHECKING SPEC] [CHECKING SPEC]

LEFT AND RIGHT SYMMETRICAL OVERSCAN 10 ± 2.5%

15-1 15-2
21FL91
 21FL91

ADJUSTMENT ADJUSTMENT
V-PHASE CLOSED CAPTION SET UP
ITEM ITEM
ADJUSTMENT ADJUSTMENT
V06 STEP RANGE 0-7 V18 STEP RANGE 0~255
POSITION POSITION

CONTROL I2C CONTROL CONTROL I2C CONTROL

PRE-ADJUST PRE-ADJUST
OPTION SET UP, BUS SET UP, CRT-PURITY OPTION SET UP, BUS SET UP
REQUIREMENT REQUIREMENT

CONTENT US 4 CH LION HEAD (MONOSCOPE PATTERN) CONTENT US 4 CH LION HEAD

INPUT INPUT AC 220V

220V, RF INPUT, ZERO MAGNETIC FIELD
CONDITION CONDITION

OUTPUT CONFIRMATION ON CRT SCREEN OUTPUT CONFIRMATION ON CRT DISPLAY.

ADJUST V06 BUS DATA TO HAVE MOST ACCEPTABLE VERTICAL PO- 1) BY SELECTING THE V18, BOX BLK TEXT WILL BE APPEARED.
SITION. 2) ADJUST THE V18 BUS DATA TO HAVE A BALANCE POSITION TO
THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL SPEC OF A=B.
POSITION
NOTE: THE DATA FOR V06 LIMIT AT <= 04, EVEN POSITION GOOD
ENOUGH

16
TEXT BOX BLK

ADJUSTMENT ADJUSTMENT
PROCEDURE PROCEDURE

A B

[CHECKING CONFIRMATION] [CHECKING SPEC]

LEFT AND RIGHT SYMMETRICAL

16-1 16-2
 ADJUSTMENT ADJUSTMENT
H-VCO PIF-VCO
ITEM ITEM
ADJUSTMENT ADJUSTMENT
V21 STEP RANGE 0-7 V10 STEP RANGE 0~63
POSITION POSITION

CONTROL I2C CONTROL CONTROL I2C CONTROL

PRE-ADJUST PRE-ADJUST
OPTION SET UP, BUS SET UP OPTION SET UP, BUS SET UP
REQUIREMENT REQUIREMENT

CONTENT NO SIGNAL (RASTER) CONDITION CONTENT NO SIGNAL (RASTER) CONDITION

INPUT INPUT AC 220V

AC 220V
CONDITION CONDITION

OUTPUT IC 801 PIN 11 OUTPUT CONFIRMATION ON CRT DISPLAY (AUTO), IC801 PIN 2 VOLTAGE (MANUAL).

(MANUAL ADJ) (AT SELF ADJUSTMENT MODE)

1) GO TO SERVICE MODE, 1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
2) GO TO SERVICE DATA V21, ADJ UNTIL FREQ AS BELOW 2) PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR “OK” AT
SCREEN
(SELF ADJ) 3) IF APPEAR “NG” PLS REPEAT STEP2
1) GO TO SERVICE MODE,BY SELECTING THE SERVICE DATA V21
2) PRESS THE R/C TO OPERATE AUTO H-VCO,OSD APPEAR "OK" AT (AT MANUAL ADJUSTMENT MODE)
SCREEN 1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
3) IF APPEAR "NG" PLS REPEAT STEP2 2) ADJUST THE DATA UP/DOWN UNTIL IC801 PIN 2 VOLTAGE BECOME

17
AS SPECIFIED BELOW
ADJUSTMENT ADJUSTMENT
PROCEDURE PROCEDURE

[CHECKING SPEC] [CHECKING SPEC]

FREQ = 15.735 ± 0.2 KHz 2.5 ± 0.5 V DC (CHECKING SPEC : 2.50 ± 1.5V)

17-1 17-2
21FL91
 21FL91

ADJUSTMENT ADJUSTMENT
RF-AGC SCREEN
ITEM ITEM
ADJUSTMENT ADJUSTMENT
V08 STEP RANGE 0-127 V11,V12,V13 STEP RANGE 0-255
POSITION POSITION

CONTROL I2C CONTROL CONTROL I2C CONTROL

PRE-ADJUST PRE-ADJUST
OPTION SET UP, BUS SET UP OPTION SET UP, BUS SET UP
REQUIREMENT REQUIREMENT

CONTENT US10CH HALF COLOR BAR CONTENT WINDOW PATTERN OR US4CH LION HEAD

INPUT RF INPUT INPUT 220V

CONDITION FIELD STRENGTH 53dBµV (FIX) CONDITION

OUTPUT TUNER AGC TERMINAL (TP 201) OR CRT DISPLAY CONFIRMATION OUTPUT CONFIRMATION ON CRT DISPLAY

(AT SELF ADJUSTMENT MODE) 1) IN SERVICE MODE, SET V04&V11&V12&V13 TO 127; V14&V15 TO
1. GO TO SERVICE MODE 64, GET IN Y-MUTE BY R/C AND SET V19 TO “1”, PICTURE APPEAR
2. GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC IN CUT-OFF CONDITION
KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN. 2) ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW
3. IF APPEAR NG PLS REPEAT STEP 2 AGAIN. BRIGHT, THEN JUDGE THAT WHETHER THE CUT-OFF LINE APPEAR
IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION V11=R-
(AT MANUAL ADJUSTMENT MODE) CUTOFF, V12=G-CUTOFF, V13=B-CUTOFF, FIX THE DATA OF THE

18
1. ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BE- COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE
COME MAXIMUM, THEN DROP 0.1V BELOW MAXIMUM VOLTAGE. OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE COLOR BE-
2. CHANGE THE ANTENNA INPUT SIGNAL TO 63-67 dBµV, AND MAKE COME WHITE.
ADJUSTMENT SURE THERE IS NO NOISE ADJUSTMENT 3) TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DIS-
PROCEDURE 3. CHANGE THE ANTENNA INPUT SIGNAL TO 90-95 dBµV TO BE SURE PROCEDURE APPEAR AND USE R/C TO SET V19 TO “0”, NEXT DISABLE THE Y-
THAT THERE IS NO CROSS MODULATION BEAT. MUTE SO THAT PICTURE APPEAR IN NORMAL MODE.

[CHECKING SPEC] [VOLTAGE CONFIRMATION]

MAX - 0.1V dc

18-1 18-2
 ADJUSTMENT ADJUSTMENT
WHITE BALANCE SUB-BRIGHT
ITEM ITEM
ADJUSTMENT ADJUSTMENT
V14,V15,V11,V12,V13 STEP RANGE 0-127, 0~255 V04 STEP RANGE 0-255
POSITION POSITION

CONTROL I2C BUS CONTROL CONTROL I2C CONTROL

PRE-ADJUST PRE-ADJUST
OPTION SET UP, BUS SET UP, SCREEN OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE
REQUIREMENT REQUIREMENT

CONTENT 23CH 501RE WINDOW PATTERN CONTENT WINDOW PATTERN

INPUT 220V INPUT 220V

CONDITION CONDITION

OUTPUT CRT SCREEN DISPLAY. OUTPUT CRT SCREEN DISPLAY.

1) WHITE (HIGH BEAM) 1) LET THE GUN POINT AT BLACK POSITION (AS ATTACH DRAWING),
FIRST LET THE GUN POINT AT BLACK POSITION (AS DRAWING ADJUST V04 BUS DATA UNTIL BRIGHTNESS Y=0.5 cd/m2, THEN
ATTACH), ADJ V04 UNTIL BRIGHTNESS Y BECOME 5 cd/m2, THEN STEP DOWN MORE 4 STEP
LET THE GUN POINT AT WHITE POSITION (AS DRAWING ATTACH),
ADJUST V01 UNTIL BRIGHTNESS Y BECOME 150 cd/m2, ADJUST
THE BUS DATA OF V14 (R DRIVE), V15(B DRIVE) UNTIL THE AXIS
OF COLOR TEMPERATURE BECOME X=0.273, Y=0.280
2) BLACK (LOW BEAM)
LET THE GUN POINT AT BLACK POSITION, IF THE VALUE SHIFTED

19
AWAY FROM THE DATA ADJUSTED IN STEP 1), ADJUST AGAIN THE
ADJUSTMENT TWO SERVICE DATA WHICH HAVE CHOSEN AT SCREEN ADJUST ADJUSTMENT
PROCEDURE SO THAT TO OBTAIN THE SIMILAR AXIS AS ABOVE. PROCEDURE
*WARNING: DO NOT DISTURB THE MINI STEP GUN DATA DURING US14
BLACK
THIS ADJUSTMENT.
**REPEAT STEP 1), 2) TO GET A REGULATED POSITION.

WHITE

US14 BLACK

[CHECKING CONFIRMATION] [VOLTAGE CONFIRMATION]

X=0.273, Y=0.280 (11,600°K + 1 MPCD) BRIGHTNESS Y=0.5 cd/m2, THEN STEP DOWN MORE 4 STEP

19-1 19-2
21FL91
 21FL91

ADJUSTMENT ADJUSTMENT
SUB-PICTURE SUB-TINT
ITEM ITEM
ADJUSTMENT ADJUSTMENT
V01 STEP RANGE 0-127 V02 STEP RANGE 0-127
POSITION POSITION

CONTROL I2C BUS CONTROL CONTROL I2C CONTROL

PRE-ADJUST PRE-ADJUST
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE, SUB-BRIGHTNESS OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
REQUIREMENT REQUIREMENT

CONTENT WINDOW PATTERN CONTENT US 10 CH HALF COLOR BAR PATTERN

INPUT INPUT 220V

220V
CONDITION CONDITION
B-AMP TR BASE (TP853)
OUTPUT CRT SCREEN DISPLAY. OUTPUT
CONFIRRM WITH OSCILLOSCOPE
1) LET THE GUN POINT AT WHITE POSITION (AS ATTACH DRAWING), 1) GET IN Y-MUTE FUNCTION BY R/C.
ADJUST V01 BUS DATA UNTIL BRIGHTNESS Y=150 cd/m2. 2) ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW.
NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN’T MATCH 3) DISABLE THE Y-MUTE
THE SPEC **PLS TAKE NOTE THAT SERVICE MODE DATA F53 NEED TO SET +8

20
WHITE
B-AMP BASE (TP853)
MUST BE IN STEPPING
ADJUSTMENT ADJUSTMENT
LEVEL
PROCEDURE PROCEDURE
US14

[VOLTAGER CONFIRMATION] [CONFIRMATION]

BRIGHTNESS Y=150 cd/m2

20-1 20-2
 ADJUSTMENT ADJUSTMENT
SUB-COLOR X-RAY PROTECTION OPERATING CONFIRMATION
ITEM ITEM
ADJUSTMENT ADJUSTMENT
V03 STEP RANGE 0-127 – STEP RANGE –
POSITION POSITION

CONTROL I2C BUS CONTROL CONTROL –

PRE-ADJUST PRE-ADJUST
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, SUB-PICT, SUB-TINT AFTER ALL ADJUSTMENT FINISHED.
REQUIREMENT REQUIREMENT

CONTENT US 10 CH HALF COLOR BAR PATTERN CONTENT US 4 CH LION HEAD (MONOSCOPE PATTERN)

INPUT 220V INPUT AC 220V, RF INPUT

CONDITION CONDITION
R-AMP TR BASE (TP851)
OUTPUT OUTPUT CONFIRMATION BY THE CRT
CONFIRRM WITH OSCILLOSCOPE
1) SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW SET THE USER CONTROL TO SHIPMENT POSITION.
2) THIS WAVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS
OF COLOR BAR BEAT AT THE SAME LEVEL [VOLTAGE CONFIRMATION]
*PLEASE TAKE NOTE THAT SERVICE DATA F52 MUST SET TO +10 CHECK THE VOLTAGE OF P603 PIN 3 AS SPECIFIED BELOW.

[OPERATION CONFIRMATION]
Cy G
SUPPLY THE DC VOLTAGE TO P603 PIN 3 AND MAKE SURE THE PRO-
TECTOR IS FUNCTIONED.
HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.

21
ADJUSTMENT ADJUSTMENT [RECOVER INFORMATION]
PROCEDURE PROCEDURE PULL OUT THE AC CORD.
100% WHITE
[CAUTION]
FROM THE RECOVER CONFIRMATION MENTIONED ABOVE, THE AC
W Y Mg R B
CODE MUST BE PULLED OUT AT LEAST 4 SECOND BEFORE PLUG-
GING IN AGAIN.(IN ORDER TO MAKE SURE THE µ-COM HAS BEEN
RESET.)

[VOLTAGE CONFIRMATION]

TP VOLTAGE OPERATION VOLTAGE

18.9± 1.1V DC 24.5V

[CHECKING CONFIRMATION]

21-1 21-2
21FL91
 21FL91

ADJUSTMENT ADJUSTMENT
HIGH VOLTAGE MS LEVEL ADJUSTMENT
ITEM ITEM
ADJUSTMENT ADJUSTMENT
– STEP RANGE – M01 STEP RANGE 0~15
POSITION POSITION

CONTROL – CONTROL I2C BUS CONTROL

PRE-ADJUST PRE-ADJUST
AFTER ALL ADJUSTMENT FINISHED. OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
REQUIREMENT REQUIREMENT

CONTENT US 4 CH LION HEAD (MONOSCOPE PATTERN) CONTENT MONORAL SIGNAL (400HZ 100% MODULATION)

INPUT AC 220V, RF INPUT INPUT AC 220V, RF INPUT

CONDITION CONDITION

OUTPUTΩ CRT ANODE VOLTAGE OUTPUT IC 3001 39 PIN

SET THE USER CONTROL TO SHIPMENT SETTING POSITION. PUSH 1) SET THE SOUND VOLUME CONTROL MORE THAN 1.
ON Y-MUTE BY R/C CONFIRM THE VOLTAGE OF CRT ANODE BY HIGH 2) ADJUST BUS DATA OF M01 UNTIL THE VOLTAGE OF 39 PIN BE-
VOLTAGE METER AND MAKE SURE THE READING IS AS BELOW. COME AS SPECIFIED BELOW.

HIGH VOLTAGE
BELOW 30kV

22
ADJUSTMENT
PROCEDURE ADJUSTMENT
PROCEDURE

[CAUTION POINT]
USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL/
[CHECKING SPEC]
DHHS STANDARD TO MAKE CORRECTION AND CONTROL.
490 ± 10mVrms (CHECKING SPEC :490 ± 20mVrms)

22-1 22-2
 ADJUSTMENT ADJUSTMENT
MTS+VCO ADJUSTMENT FILTER ADJUSTMENT
ITEM ITEM
ADJUSTMENT ADJUSTMENT
M02 STEP RANGE 0~63 M03 STEP RANGE 0~63
POSITION POSITION

CONTROL I2C BUS CONTROL CONTROL I2C BUS CONTROL

PRE-ADJUST PRE-ADJUST
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO
REQUIREMENT REQUIREMENT

CONTENT SIGNAL WITHOUT NOISE (SIGNAL WITHOUT SOUND MODULATION) CONTENT SINE WAVE (9.4kHz, 600mVrms)

INPUT AC 200V INPUT PIN 14 (FROM C3005 - TERMINAL)

CONDITION CONDITION

OUTPUT IC 3001 39 PIN OUTPUT CONFIRM BY CRT SCREEN

1) CONNECT 100 µ F ELECTROLLYTIC CAPACITOR BETWEEN C3005 1) ADJUST M03 DATA UNITILL OK DISPLAY ON SCREEN ADJUST THE
(-ve)-GND BUS DATA IN CENTRE OF THE RANGE.
2) ADJUST THE BUS DATA M02 UNTIL THE OUTPUT FREQUENCY OF
39 PIN BECOME AS SPECIFIED BELOW.
NOTE: TO MINIMIZE THE PRODUCTION TIME, ITEM 1) CAN IGNORE.
IF ITEM 2) CAN'T BE ADJUST, THEN ITEM 1) IS REQUIRE.

23
ADJUSTMENT ADJUSTMENT
PROCEDURE PROCEDURE

[CHECKING SPEC] [CHECKING SPEC]

62.94 ± 0.75kHz (CHECKING SPEC : 62.94 ± 1.20kHz) REFER TO ABOVE (CHECKING SPEC : ± 2 STEP TO CENTRE)

23-1 23-2
21FL91
 21FL91

ADJUSTMENT
SEPARTION ADJUSTMENT
ITEM
ADJUSTMENT
M04, M05 STEP RANGE 0~63
POSITION

CONTROL I2C BUS CONTROL

PRE-ADJUST
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO, FILTER
REQUIREMENT
STEREO SIGNAL SIGNAL 1,: MODULATION 30%, L-CH ONLY, NR-ON, 300Hz
CONTENT
SIGNAL 2,: MODULATION 30%, L-CH ONLY, NR-ON, 3kHz
INPUT
RF INPUT
CONDITION

OUTPUT IC 3001 39 PIN

1) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNTIL THE AC

VOLTAGE OF 39 PIN BECOME MINIMUM LEVEL.
2) INPUT SIGNAL 2, ADJUST BUS DATA OF M05 UNTIL THE AC VOLT-
AGE OF 39 PIN BECOME MINIMUM LEVEL.
3) REPEAT STEP 1) AND 2).

SET THE SOUND VOLUME TO MAXIMUM THEN MAKE SURE THE

24
READING FROM THE SPEAKER TERMINAL MUST BE OVER THE SPEC
AS SPECIFIED BELOW.

ADJUSTMENT
PROCEDURE

[CHECKING SPEC]
OVER 25 dB (CHECKING SPEC : OVER 20 dB)

24-1 24-2
 21FL91

-MEMO-

25
21FL91

CHASSIS LAYOUT
H

1 2 3 4 5 6

26
 21FL91

CRT BLOCK DIAGRAM

H

1 2 3 4 5 6

27
21FL91 21FL91

MAIN BLOCK DIAGRAM

J

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

28~29
21FL91 21FL91

MTS BLOCK DIAGRAM

J

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

30~31
21FL91

DESCRIPTION OF SCHEMATIC DIAGRAM

NOTES: WAVEFORM MEASUREMENT CONDITIONS:
1. The unit of resistance "ohm" is omitted. 1. Photographs taken on a standard gated color bar
(K=kΩ=1000Ω, M=MΩ) signal, the tint setting adjusted for proper color. The
2. All resistors are 1/16 watt, unless otherwise noted. wave shapes at the red, green and blue cathodes of
3. All capacitors are µF, unless otherwise noted. the picture tube depend on the tint, color level and
(P=pF=µµF) picture control.
4. (G) indicates ±2% tolerance may be used. 2. indicates waveform check points (See chart,
5. indicates line isolated ground. waveforms are measured from point indicated to
chassis ground.)
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected å AND SHADED ( ) COMPONENTS
between points indicated and chassis ground, line = SAFETY RELATED PARTS.
voltage set at 120V AC and all controls set for normal ç MARK= X-RAY RELATED PARTS.
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color DRGANNES MARQUES åET HACHRES ( ):
signal. PIECES RELATIVES A LA SECURITE.
MARQUE ç : PIECS RELATIVE AUX RAYONS X.

This circuit diagram is a standard one, printed circuits

may be subject to change for product improvement
without prior notice.

WAVEFORMS

32
 21FL91

SCHEMATIC DIAGRAM: CRT Unit

H

1 2 3 4 5 6

33
21FL91 21FL91

SCHEMATIC DIAGRAM: MAIN Unit

J

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

34~35
21FL91 21FL91

SCHEMATIC DIAGRAM: MTS MODULE Unit

J

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

36~37
21FL91

PRINTED WIRING BOARD ASSEMBLIES

H

PWB-A: MAIN Unit (Wiring Side)

1 2 3 4 5 6

38
 21FL91

RJ 4 0

R1 0 2 6

RJ 4 5

RJ 4 1
RJ 4 3
R1 0 0 8

R1 0 0 6
R3 8 4

RJ 4 6

R4 3 2

R4 3 1
R1 0 0 7 R1 0 0 9 R1 0 0 2

R3 8 2
R3 8 3
RJ 1 6 RJ 4 8
R1 0 2 7
R1 0 0 3

R3 8 1
RJ 6 0

B2

R3 2 1
Z1 A1
RJ 3 0

F DC2

R3 1 2

RJ 1 1
RJ 5 9

R3 1 4
RJ 7 6

R3 1 3
C3 1 3

R3 1 5

RJ 7 1
C3 1 9
C3 2 0
RJ 9

RJ 0
R3 110

RJ 8

RJ 1 3

R3 0 6

R3 0 5
F

RJ 1 5
R3 1 6
RJ 2 1

Q3 0 1 Q3 0 2
C3 0 8

R3 0 7

R3 1 7
RJ 1 4 R3 1 0
R3 1 8
R3 0 8

RJ 7 7
R3 0 3

RJ 7 0

RJ 7 4

R1 0 8 1

C7 5 9
R7 6 6

Q7 4 1

R1 0 5 9

R7 6 8
Q7 5 5

R4 5 4

R7 4 4
R1 0 5 2

R7 4 3
R1 0 4 3 Q7 4 0
R1 0 7 6

R1 0 5 3

R1 0 4 7

D1 0 9 0

D1 0 0 4
R1 0 4 9

R1 0 3 3
R1 0 3 8

R1 0 5 7

E
RJ 6 9

R1 0 4 8

R1 0 3 4
RJ 3 6
D1 0 8 6

R1 0 5 1

R1 0 6 4

R1 0 3 7

R1 0 3 6
R1 0 4 6
Q1 0 0 2 D1 0 8 5

R1 0 2 4
RJ 2 3
R1 0 3 9
R1 0 6 5 Q1 0 0 1
R1 0 5 6 R1 0 5 4 D1 0 8 8 R1 0 7 3

R1 0 5 5

C1 0 1 5
R1 0 7 2

I C1 0 0 1

RJ 3 9
RJ 3 3 C1 0 0 4
RJ 3 5

D1 0 8 7
R1 0 7 4
R1 0 2 5

RJ 1 7
R1 0 7 1
C7 8 4

F DC3

R1 0 6 8

R1 0 7 0

R1 0 7 5
RJ 6 3

R1 0 6 9
C1 0 1 3

I C1 0 0 3

RJ 2 2
R1 0 6 1

R1 0 3 2

R1 0 3 1
RJ 3 2

R1 0 6 6

R1 0 6 7
Q6 0 4
C7 3 5

R1 0 2 2

R1 0 2 1
C1 0 1 1 C1 0 0 9

R1 0 6 0

C1 8 5 5

R8 4 2
C1 0 1 0

C1 0 0 8
R7 1 4

R6 6 2

C8 1 0
R6 6 1

RJ 1 9

R8 0 7
R8 1 0
R1 0 6 2
R1 0 6 3

R1 8 5 1

R8 0 4
R8 4 3

C8 0 9
R1 8 5 3

R1 8 5 2

D8 1 0
R8 0 6

R8 0 5
C8 1 5

C8 1 6

R8 3 8
C8 1 3

C8 1 1

C8 0 6
R8 4 0
D8 1 2

RJ 4 2
R8 0 2
C8 0 8

C8 1 4
Q8 0 4

D8 1 5
Q8 0 3
R8 1 3
D8 1 1
R8 0 3

R8 0 1
C8 1 2
R8 1 1

D8 1 3
R8 1 6
D8 1 4
RJ 3 7

R8 3 2

RJ 6 2
R8 1 7

R8 1 5

R8 3 4
RJ 7 5

D
R8 1 4

R8 3 9

C8 0 4
R8 1 2
C8 2 3

C8 2 1

D5 0 1
C8 0 2
R5 2 0

C5 1 9

I C8 0 1
C8 1 9

R5 2 7 R8 3 5

R5 2 8

C8 4 6

RJ 7
RJ 2 6

R2 1 3
RJ 6 5

C2 1 1
R8 2 1

R2 1 2
C8 4 5
R8 2 2 R2
RJ120

D2 0 2
C8 3 1 C2 1 3
R8 1 9 C8 4
R8 340
C8 4 4

R5 2 1
R8 2 0

C2 1 0

R2 1 1
R8 3
C8 425 C8 4 7 C8 4 1

RJ 3
C8 3 3

R8 3 3
R1 8 5 4

C8 4 0
C5 1 7

R5 1 6

Q2 0 2
C8 3 6 R2 0 9
C1 8 5 6
RJ 3 8

R8 2 5

R5 2 2
RJ 4 9

RJ 5 0
C2 0 8
RJ 4 4

R2 0 8 C2 0 7
R2 2 0
R5 0 4
Q2 0 1
C2 0 9
R2 0 7

R2 0 6

R2 0 5
C5 1 8
R8 3 1
R1 8 5 0
RJ 1

RJ 1 2
R4 3 7

R8 2 8
R8 2 7
C4 3 6

RJ 4 7

I C4 0 1
R8 2 9

R1
RJ82459
C8 3 9

Q8 0 5
C2 1 2
C2 0 5
RJ 2 4

C RJ 7 2
RJ 7 3

F DC4
C2 0 3

RJ 5 3
RJ 3 4

RJ 5 1

R3 6 3
R3 6 5

RJ 5 2

C1 8 6 2
C1 8 6 4
R3 6 2

R6 1 8
R6 1 9

C1 8 6 1
R3 6 4

R1 8 6 1

C1 8 6 3
R6 2 0

R2 0 1
RJ 6 4

R2 0 2
R6 1 7

R4 3 5
RJ 6 2
R4

R6 5 4
R8 3 0
1

R1 8 6 2

Z2
F DC1 R4 3 3
R4 3 4

R4 6 1
R4 5 8

A2
B1
R6 1 3

PWB-A: MAIN Unit (Chip Parts Side)

1 2 3 4 5 6

39
21FL91

C
PWB-B: CRT Unit (Wiring Side)

1 2 3 4 5 6

40
 21FL91

PWB-E: MTS MODULE Unit (Wiring Side)

E
R3 0 2 4

D
R3 0 2 5
R3 0 8 0

RJ 1 0

R3 0 8 1
RJ 4

I C3 0 0 2

Q3 0 0 7
C3 0 0 2

R3 0 0 3

R3 0 0 4

R3 0 0 5
R3 0 1 6

C3 0 0 8
R3 0 8 4

R3 0 8 5
RJ 1 3

C3 0 8 2

R3
RJ03
76

RJ 2 Q3 0 0 6
RJ 6

I C3 0 0 1
R3 0 0 7 R3 0 1 9
R3 0 0 8
R3 0 0 2

R3 0 0 1

R3 0 8 2
R3 0 1 0

R3 0 1 8
C3 0 1 3
RJ 3

RJ 1 4

R3 0 8 3 R3 0 2 6
C3 0 3 1

C3 0 3 2 R3 0 2 9
C3 0 2 6

Q3 0 0 4
C3 0 2 8
C3 0 4 3

R3 0 1 1
Q3 0 0 1

C
C3 0 3 3
C3 0 2 5

R3 0 2 7

R3 0 1 2
Q3 0 0 2
C3 0 2 7

C3 0 2 4
C3 0 3 6

C3 0 3 5

R3 0 3 0
R3 0 3 4

R3 0 3 5

C3 0 2 3
R3 0 1 3
R3 0 2 8

C3 0 4 2

R3 0 2 1
Q3 0 0 5
R3
RJ03
83
R3 0 3 1
R3 0 3 2

R3 0 1 4

RJ 9 RJ 1 5
RJ 1 6
RJ 1 7

B PWB-E: MTS MODULE Unit (Chip Parts Side)

1 2 3 4 5 6

41
21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
REPLACEMENT PARTS LIST
å Q701 VSSTP6NC80Z1E X STP6NC80Z AF
PARTS REPLACEMENT Q703 VS2SC3198-Y-1+ X 2SC3198-Y AB
Q740 VS2SD601AR/-1~ X 2SD601AR AA
Replacement parts which have these special safety characteristics Q741 VS2SD601AR/-1~ X 2SD601AR AA
are identified in this manual; electrical components having such Q751 VS2SC2236Y/-1+ X 2SC2236Y AB
features are identified by "å" in the Replacement Parts Lists. Q752 VS2SC2236Y/-1+ X 2SC2236Y AB
Q753 VS2SC3198-G-1+ X 2SC3198-G AB
The use of a substitute replacement part which does not have the
Q755 VS2SD601AR/-1~ X 2SD601AR AA
same safety characteristics as the factory recommended replace- Q804 VS2SB709AR/-1~ X 2SB709AR AA
ment parts shown in this service manual may create shock, fire or Q805 VS2SD601AR/-1~ X 2SD601AR AA
other hazards. Q1001 VS2SD601AR/-1~ X 2SD601AR AA

"HOW TO ORDER REPLACEMENT PARTS" DIODES AND LED

D201 RH-EX0676GEZZ~ X Zener, EX0676GE AB
To have your order filled promptly and correctly, please furnish the D203 RH-DX0048GEZZ~ X DX0048GE AA
following informations. D393 RH-DX0247CEZZ~ X DX0247CE AB
D501 RH-EX1393CEZZ~ X Zener, EX1393CE AB
D502 RH-EX0652GEZZ~ X Zener, EX0652GE AB
1. MODEL NUMBER 2. REF. NO. D503 RH-EX0612GEZZ~ X Zener, EX0612GE AB
3. PART NO. 4. DESCRIPTION D504 RH-EX0654CEZZ~ X Zener, EX0654CE AC
D505 RH-DX0441CEZZ~ X DX0441CE AA
D510 RH-DX0131CEZZ~ X DX0131CE AB
MARK : SPARE PARTS-DELIVERY SECTION. D601 RH-DX0048GEZZ~ X DX0048GE AA
D602 VHD1SS244//-1~ X 1SS244 AA
D603 RH-EX0662GEZZ~ X Zener, EX0662GE AB
Ref. No. Part No. ★ Description Code
D606 RH-DX0131CEZZ~ X DX0131CE AB
D608 RH-DX0131CEZZ~ X DX0131CE AB
PICTURE TUBE å D701 RH-DX0111PEZZ X DX0111PE AC
D703 RH-DX0048GEZZ~ X DX0048GE AA
D704 RH-EX0650GEZZ~ X Zener, EX0650GE AB
å V101 VB51QDX992X2E X Picture Tube BY
D708 RH-DX0048GEZZ~ X DX0048GE AA
å L706 RCiLG0069PEZZ X Degaussing Coil AH
D710 RH-DX0048GEZZ~ X DX0048GE AA
QEARCA012WJZZ X Grounding Strap AC
D750 RH-EX0647CEZZ~ X Zener, EX0647CE AE
PMAGF3046CEZZ X Purity Magnet, x3 AC
D751 RH-DX0229CEZZ X DX0229CE AB
PSPAG0003PEZZ X Spacer, x3 AB
D752 RH-DX0131CEZZ~ X DX0131CE AB
D755 RH-DX0048GEZZ~ X DX0048GE AA
D756 RH-DX0441CEZZ~ X DX0441CE AA
D801 RH-EX0613GEZZ~ X Zener, EX0613GE AB
D806 RH-DX0048GEZZ~ X DX0048GE AA
D807 RH-EX0625GEZZ~ X Zener, EX0625GE AB
PRINTED WIRING BOARD ASSEMBLIES D808 RH-DX0048GEZZ~ X DX0048GE AA
(NOT REPLACEMENT ITEM) D810 RH-EX0263TAZZ~ X Zener, EX0263TA AB
D811 RH-EX0263TAZZ~ X Zener, EX0263TA AB
D812 RH-EX0263TAZZ~ X Zener, EX0263TA AB
PWB-A DUNTKB541WEA0 - MAIN Unit —
D813 RH-EX1393CEZZ~ X Zener, EX1393CE AB
PWB-B DUNTKA599WEA0 - CRT Unit —
D815 RH-EX0263TAZZ~ X Zener, EX0263TA AB
PWB-E DUNTKB271WEA1 - MTS MODULE Unit —
D1004 RH-EX1393CEZZ~ X Zener, EX1393CE AB
D1081 RH-DX0048GEZZ~ X DX0048GE AA
D1085 RH-EX1393CEZZ~ X Zener, EX1393CE AB
DUNTKB541WEA0 D1086 RH-EX1393CEZZ~ X Zener, EX1393CE AB
PWB-A MAIN UNIT D1087 RH-EX1393CEZZ~ X Zener, EX1393CE AB
D1088 RH-EX1393CEZZ~ X Zener, EX1393CE AB
TUNER D1089 RH-EX0613GEZZ~ X Zener, EX0613GE AB
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN D1090 RH-EX1393CEZZ~ X Zener, EX1393CE AB
ASSEMBLY NOT INDEPENDENTLY. D1091 RH-DX0048GEZZ~ X DX0048GE AA
å TU201 RTUNQA003WJZZ X Tuner AR å IC702 RH-FX0008GEZZ X PC123FY8 AB
VA701 RH-VX0073CEZZ X Varistor AB
INTEGRATED CIRCUITS
IC301 VHiAN7522++-1 X AN7522++ AF PACKAGED CIRCUITS
IC401 VHiMM1501XN-1~ X MM1501XN AC å PR701 RMPTP0001PEZZ X Packaged Circuit AE
å IC501 VHiTDA9302H-1 X TDA9302H AE å R751 RR-DZ0049CEZZ~ X Resistor AB
IC601 VHiKA7809AP-1 X KA7809AP AB å R752 RR-DZ0049CEZZ~ X Resistor AB
å IC701 VHiTEA1507/-1 X TEA1507 AE X801 RCRSAA009WJZZ X Crystal, CRSAA009WJ AC
å IC703 VHiSE130N//-1 X SE130N AF
IC801 VHiM61251FP1EQ X M61251FP AN FILTERS
IC1001 RH-iXA155WJN4 X IXA155WJ AP CF201 RFiLC0447CEZZ X Filter, FiLC0447CE AB
IC1003 VHiBR2416E2-1~ X BR2416E2 AD CF802 RFiLC0446CEZZ X Filter, FiLC0446CE AB
SF201 RFiLC0405CEZZ X Filter, FiLC0405CE AD
TRANSISTORS
Q201 VS2SC2735//1E~ X 2SC2735 AB
Q302 VS2SD601AR/-1~ X 2SD601AR AA
Q601 VS2SC2482//-1+ X 2SC2482 AB COILS
Q602 VS2SD2539//1E X 2SD2539 AG L202 VP-CF270K0000~ X Peaking, 27µH 10% AB
Q603 VS2SC3198-G-1+ X 2SC3198-G AB L203 VP-DF270K0000~ X Peaking, 27µH 10% AA
Q604 VS2SD601AR/-1~ X 2SD601AR AA

42
 21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

L204 VP-XF1R2K0000~ X Peaking, 1.2µH 10% AA C643 VCEA0A1CW477M+ X 470 16V Electrolytic AB
L602 RCiLP0223CEZZ X Coil, CiLP0223CE AB C650 VCKYPA2HB101K+ X 100p 500V Ceramic AB
L603 RCiLZA006WJZZ X Coil, CiLZA006WJ AE å C701 RC-FZ029SCEZZ X 0.22 275V AB
å L703 RCiLF0078PEZZ X Coil, CiLF0078PE AC Metallized Polypro Film
L751 RCiLP0225CEZZ X Coil, CiLP0225CE AB C702 RC-KZ0029CEZZ+ X 0.01 250V Ceramic AB
L801 VP-DF100K0000~ X Peaking, 10µH 10% AA C703 RC-KZ0029CEZZ+ X 0.01 250V Ceramic AB
L802 VP-DF100K0000~ X Peaking, 10µH 10% AA C704 RC-KZ0029CEZZ X 0.01 250V Ceramic AB
L803 VP-DF100K0000~ X Peaking, 10µH 10% AA å C705 RC-EZ0804CEZZ X 220 400V Electrolytic AH
L804 VP-XF150K0000~ X Peaking, 15µH 10% AA C706 VCQYTA1HM103J+ X 0.01 50V Mylar AA
L806 VP-DF100K0000~ X Peaking, 10µH 10% AA C711 VCFYFA1HA334J+ X 0.33 50V AB
L807 VP-XF1R2K0000~ X Peaking, 1.2µH 10% AA Metallized Polypro Film
L1861 VP-XF8R2K0000~ X Peaking, 8.2µH 10% AA C718 VCKYPA2HB472K+ X 4700p 500V Ceramic AB
L1862 VP-XF8R2K0000~ X Peaking, 8.2µH 10% AA C737 VCEA0A1EW226M+ X 22 25V Electrolytic AA
C738 RC-KZ0040CEZZ X 820p 2kV Ceramic AB
TRANSFORMERS C743 VCKYPH3DB561K X 560p 2000V Ceramic AB
å T601 RTRNZ0026PEZZ X Transformer AD C744 VCQYTA1HM104J+ X 0.1 50V Mylar AB
å T602 RTRNFA012WJZZ X H-Volt Transformer AU C751 RC-KZ0106GEZZ X 0.0033 250V Ceramic AB
å T701 RTRNWA076WJZZ X Transformer AG C752 VCKYPH3DB561K X 560p 2000V Ceramic AB
C753 RC-EZ0724CEZZ X 100 160V Electrolytic AC
CAPACITORS C754 RC-EZ0638CEZZ X 33 160V Electrolytic AD
C201 VCEA0A1CW476M+ X 47 16V Electrolytic AA C755 VCQYTA1HM103J+ X 0.01 50V Mylar AA
C202 VCEA0A0JW477M+ X 470 6.3V Electrolytic AB C756 VCEA0A1EW108M+ X 1000 25V Electrolytic AB
C203 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA C758 VCEA0A1HW225M+ X 2.2 50V Electrolytic AA
C204 VCEA0A0JW477M+ X 470 6.3V Electrolytic AB C759 VCKYCY1HB102K~ X 1000p 50V Ceramic AA
C205 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA C784 VCKYCY1HB103K~ X 0.01 50V Ceramic AA
C206 VCEA0A1HW106M+ X 10 50V Electrolytic AA C801 VCFYFA1HA105J+ X 1 50V AB
C207 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA Metallized Polypro Film
C208 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA C802 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C209 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA C803 VCEA0A1AW476M+ X 47 10V Electrolytic AA
C210 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA C804 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C213 VCKYCY1HB102K~ X 1000p 50V Ceramic AA C805 VCEA0A1HW105M+ X 1 50V Electrolytic AA
C301 VCEA0A1CW477M+ X 470 16V Electrolytic AB C806 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C304 VCEA0A1CW106M+ X 10 16V Electrolytic AA C807 VCEA0A1CW337M+ X 330 16V Electrolytic AB
C307 VCEA0A1HW105M+ X 1 50V Electrolytic AA C808 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C308 VCKYCY1HF153Z~ X 0.015 50V Ceramic AA C809 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C310 VCEA0A1HW225M+ X 2.2 50V Electrolytic AA C810 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C311 VCEA0A1HW105M+ X 1 50V Electrolytic AA C811 VCKYCY1EF104Z~ X 0.1 25V Ceramic AA
C312 VCEA0A1CW476M+ X 47 16V Electrolytic AA C812 VCKYCY1EF104Z~ X 0.1 25V Ceramic AA
C313 VCKYCY1HF153Z~ X 0.015 50V Ceramic AA C813 VCKYCY1EF104Z~ X 0.1 25V Ceramic AA
C321 VCEA0A1CW476M+ X 47 16V Electrolytic AA C814 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C322 VCEA0A1HW105M+ X 1 50V Electrolytic AA C815 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C377 VCEA0A1CW107M+ X 100 16V Electrolytic AA C816 VCKYCY1EF104Z~ X 0.1 25V Ceramic AA
C391 VCKYPA1HB102K+ X 1000p 50V Ceramic AA C817 VCEA0A1AW107M+ X 100 10V Electrolytic AA
C392 VCQYTA1HM103J+ X 0.01 50V Mylar AA C818 VCEA0A1HW475M+ X 4.7 50V Electrolytic AA
C393 VCEA0A1EW108M+ X 1000 25V Electrolytic AB C819 VCCCCY1HH121J~ X 120p 50V Ceramic AA
C434 VCEA0A1CW106M+ X 10 16V Electrolytic AA C820 VCEA0A1HW474M+ X 0.47 50V Electrolytic AA
C435 VCE9GA1CW106M+ X 10 16V Electrolytic AB C821 VCKYCY1HF153Z~ X 0.015 50V Ceramic AA
C436 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA C822 VCE9GA1HW105M+ X 1 50V Electrolytic AB
C452 VCEA9M1CW106M+ X 10 16V Electrolytic AA C823 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C505 VCEA0A1HW107M+ X 100 50V Electrolytic AB C824 VCEA0A1CW337M+ X 330 16V Electrolytic AB
C508 VCFYAA2AA224J+ X 0.22 100V AC C825 VCE9EM1HW105M+ X 1 50V Electrolytic AB
Metallized Polypro Film C826 VCKYPA1HF103Z+ X 0.01 50V Ceramic AA
C509 VCKYD41CY103N~ X 0.01 16V Ceramic AA C827 VCEA9M1CW476M+ X 47 16V Electrolytic AA
C511 VCEA0A1VW477M+ X 470 35V Electrolytic AB C828 VCKYPA1HB103K+ X 0.01 50V Ceramic AB
C512 VCKYPA2HB102K+ X 1000p 500V Ceramic AB C829 VCEA0A1CW476M+ X 47 16V Electrolytic AA
C513 VCEA0A1VW108M+ X 1000 35V Electrolytic AA C831 VCKYCY1EF104Z~ X 0.1 25V Ceramic AA
C514 VCFYSA1JB273J+ X 0.027 63V AB C833 VCKYCY1EF104Z~ X 0.1 25V Ceramic AA
Metallized Polypro Film C834 VCEA0A1CW107M+ X 100 16V Electrolytic AA
C515 VCEACA1HC335J+ X 3.3 50V Electrolytic AB C835 VCEA0A1CW106M+ X 10 16V Electrolytic AA
C518 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA C836 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C519 VCKYCY1HB102K~ X 1000p 50V Ceramic AA C837 VCEA0A1HW105M+ X 1 50V Electrolytic AA
C601 VCQYTA1HM563J+ X 0.056 50V Mylar AA C839 VCCCCY1HH680J~ X 68p 50V Ceramic AA
C602 VCEA0A1HW475M+ X 4.7 50V Electrolytic AA C840 VCKYCY1EF104Z~ X 0.1 25V Ceramic AA
C603 VCEA0A1HW105M+ X 1 50V Electrolytic AA C841 VCCCCY1HH101J~ X 100p 50V Ceramic AA
C604 VCEA0A2EW336M+ X 33 250V Electrolytic AB C842 VCEA9M1HW474M+ X 0.47 50V Electrolytic AA
C605 VCKYPA2HB102K+ X 1000p 500V Ceramic AB C843 VCEA9M1HW105M+ X 1 50V Electrolytic AA
C606 VCKYPA2HB102K+ X 1000p 500V Ceramic AB C845 VCKYCY1CF224Z~ X 0.22 16V Ceramic AA
å C607 VCFPVC3ZA902H X 9000p 1800V AB C846 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
MetalIized Polypro Film C847 VCCCCY1HH220J~ X 22p 50V Ceramic AA
C608 VCKYPA2HB561K+ X 560p 500V Ceramic AB C848 VCEA0A1HW105M+ X 1 50V Electrolytic AA
C610 VCFYSB2EB823J X 0.082 250V AB C1001 VCEA0A0JW107M+ X 100 6.3V Electrolytic AA
MetalIized Polypro Film C1003 VCEA0A1CW106M+ X 10 16V Electrolytic AA
C611 VCFPVC2DB244J X 0.24 200V AB C1004 VCKYCY1CF474Z~ X 0.47 16V Ceramic AA
MetalIized Polypro Film C1006 VCEA0A1HW225M+ X 2.2 50V Electrolytic AA
C641 VCEA0A1EW108M+ X 1000 25V Electrolytic AB C1007 VCEA0A1CW107M+ X 100 16V Electrolytic AA
C642 VCEA0A1EW476M+ X 47 25V Electrolytic AA C1008 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA

43
21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

C1009 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA R362 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA
C1011 VCKYCY1HB221K~ X 220p 50V Ceramic AA R363 VRS-CY1JF564J~ X 560k 1/16W Metal Oxide AA
C1012 VCEA0A1HW105M+ X 1 50V Electrolytic AA R364 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA
C1013 VCKYCY1HB102K~ X 1000p 50V Ceramic AA R365 VRS-CY1JF564J~ X 560k 1/16W Metal Oxide AA
C1014 VCEA0A1HW475M+ X 4.7 50V Electrolytic AA R381 VRS-CY1JF564J~ X 560k 1/16W Metal Oxide AA
C1015 VCCCCY1HH101J~ X 100p 50V Ceramic AA R382 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA
C1081 VCEA0A1HW104M+ X 0.1 50V Electrolytic AA R383 VRS-CY1JF564J~ X 560k 1/16W Metal Oxide AA
C1849 VCFYFA1HA223J+ X 0.022 50V AA R384 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA
Metallized Polypro Film R431 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA
C1855 VCKYCY1HB561K~ X 560p 50V Ceramic AA R432 VRS-CY1JF750J~ X 75 1/16W Metal Oxide AA
C1856 VCKYCY1HB102K~ X 1000p 50V Ceramic AA R433 VRS-CY1JF750J~ X 75 1/16W Metal Oxide AA
C1861 VCCCCY1HH221J~ X 220p 50V Ceramic AA R434 VRS-CY1JF750J~ X 75 1/16W Metal Oxide AA
C1862 VCKYCY1HB102K~ X 1000p 50V Ceramic AA R435 VRS-CY1JF750J~ X 75 1/16W Metal Oxide AA
C1863 VCCCCY1HH221J~ X 220p 50V Ceramic AA R437 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA
C1864 VCKYCY1HB102K~ X 1000p 50V Ceramic AA R461 VRS-CY1JF750J~ X 75 1/16W Metal Oxide AA
R462 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA
RESISTORS R502 VRS-RG3AB102J+ X 1k 1W Metal Oxide AB
C211 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R503 VRN-RL3DB1R2J+ X 1.2 2W Metal Film AB
RJ1 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R504 VRS-CY1JF222J~ X 2.2k 1/16W Metal Oxide AA
RJ2 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R506 VRS-RG3AB331J+ X 330 1W Metal Oxide AB
RJ3 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R507 VRD-RM2HD1R0J~ X 1 1/2W Carbon AA
RJ4 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R513 VRD-RM2HD333J~ X 33k 1/2W Carbon AA
RJ7 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R514 VRD-RM2HD682J~ X 6.8k 1/2W Carbon AA
RJ9 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R520 VRS-CY1JF123J~ X 12k 1/16W Metal Oxide AA
RJ10 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R522 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA
RJ11 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R523 VRD-RA2BE101J~ X 100 1/8W Carbon AA
RJ13 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R524 VRD-RA2BE103J~ X 10k 1/8W Carbon AA
RJ14 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R525 VRD-RA2BE122J~ X 1.2k 1/8W Carbon AA
RJ15 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R526 VRD-RA2BE101J~ X 100 1/8W Carbon AA
RJ16 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R528 VRS-CY1JF683J~ X 68k 1/16W Metal Oxide AA
RJ17 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R602 VRD-RA2BE393J~ X 39k 1/8W Carbon AA
RJ19 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R603 VRD-RA2BE273J~ X 27k 1/8W Carbon AA
RJ22 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R604 VRD-RA2BE473J~ X 47k 1/8W Carbon AA
RJ23 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R605 VRD-RM2HD104J~ X 100k 1/2W Carbon AA
RJ33 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R606 VRN-RL3LBR27J+ X 0.27 3W Metal Film AB
RJ35 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA å R608 VRD-RM2HD102J~ X 1k 1/2W Carbon AA
RJ37 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA å R611 VRN-RL3ABR27J+ X 0.27 1W Metal Film AB
RJ39 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA å R612 VRD-RM2HD270J~ X 27 1/2W Carbon AA
RJ41 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R613 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA
RJ42 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R614 VRD-RA2BE154J~ X 150k 1/8W Carbon AA
RJ43 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R615 VRD-RA2BE102J~ X 1k 1/8W Carbon AA
RJ47 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R616 VRD-RA2BE102J~ X 1k 1/8W Carbon AA
RJ50 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R617 VRS-CY1JF123J~ X 12k 1/16W Metal Oxide AA
RJ51 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R618 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
RJ52 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R621 VRN-RL2HC4R7J+ X 4.7 1/2W Metal Film AB
RJ53 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R622 VRS-VV3DB682J X 6.8k 2W Metal Oxide AA
RJ60 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R631 VRS-KT3LB391J X 390 3W Metal Oxide AB
RJ62 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R632 VRS-RG3LB122J+ X 1.2k 3W Metal Oxide AB
RJ63 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA å R633 VRS-KA3NG3R3K X 3.3 7W Metal Oxide AB
RJ65 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R637 VRD-RA2BE331J~ X 330 1/8W Carbon AA
RJ69 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R638 VRD-RA2BE331J~ X 330 1/8W Carbon AA
RJ70 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R639 VRD-RM2HD562J~ X 5.6k 1/2W Carbon AA
RJ71 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R642 VRD-RM2HD470J~ X 47 1/2W Carbon AA
RJ72 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R643 VRS-KA3HG912J X 9.1k 5W Metal Oxide AB
RJ75 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R661 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
RJ76 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA R662 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
R201 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA R701 VRW-KQ3NC1R5K X 1.5 7W Cement AB
R202 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA R702 VRD-RM2HD100J~ X 10 1/2W Carbon AA
R205 VRS-CY1JF680J~ X 68 1/16W Metal Oxide AA R705 VRN-VV3DBR33J X 0.33 2W Metal Film AB
R206 VRS-CY1JF122J~ X 1.2k 1/16W Metal Oxide AA R706 VRN-VV3DBR27J X 0.27 2W Metal Film AB
R207 VRS-CY1JF221J~ X 220 1/16W Metal Oxide AA R707 VRD-RM2HD270J~ X 27 1/2W Carbon AA
R208 VRS-CY1JF331J~ X 330 1/16W Metal Oxide AA R708 VRD-RA2BE102J~ X 1k 1/8W Carbon AA
R209 VRS-CY1JF392J~ X 3.9k 1/16W Metal Oxide AA R710 VRS-RG2HC103J+ X 10k 1/2W Metal Oxide AB
R216 VRS-VV3LB333J X 33k 3W Metal Oxide AB R711 VRD-RA2BE394J~ X 390k 1/8W Carbon AA
R220 VRS-CY1JF221J~ X 220 1/16W Metal Oxide AA R713 VRD-RM2HD122J~ X 1.2k 1/2W Carbon AA
R301 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA R715 VRD-RA2BE150J~ X 15 1/8W Carbon AA
R302 VRN-RL3DBR22J+ X 0.22 2W Metal Film AB R716 VRD-RA2BE223J~ X 22k 1/8W Carbon AA
R303 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA å R720 VRW-GA4AB1R5K X 1.5 10W Cement AC
R304 VRD-RA2BE683J~ X 68k 1/8W Carbon AA R725 VRD-RM2HD821J~ X 820 1/2W Carbon AA
R305 VRS-CY1JF274J~ X 270k 1/16W Metal Oxide AA R726 VRN-RL2HCR47J+ X 0.47 1/2W Metal Film AB
R307 VRS-CY1JF222J~ X 2.2k 1/16W Metal Oxide AA R742 VRD-RA2BE183J~ X 18k 1/8W Carbon AA
R308 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA R743 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA
R310 VRS-CY1JF473J~ X 47k 1/16W Metal Oxide AA R744 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA
R311 VRD-RA2BE272J~ X 2.7k 1/8W Carbon AA R745 VRD-RA2BE472J~ X 4.7k 1/8W Carbon AA
R314 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA R746 VRD-RA2BE223J~ X 22k 1/8W Carbon AA
R315 VRS-CY1JF222J~ X 2.2k 1/16W Metal Oxide AA R753 VRD-RM2HD124J~ X 120k 1/2W Carbon AA

44
 21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
R754 VRN-RL3DB8R2J+ X 8.2 2W Metal Film AB R1063 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
R755 VRS-RG3DB150J+ X 15 2W Metal Oxide AB R1064 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
R756 VRS-RG3DB121J+ X 120 2W Metal Oxide AB R1065 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
R759 VRS-RG3DB101J+ X 100 2W Metal Oxide AB R1066 VRS-CY1JF561J~ X 560 1/16W Metal Oxide AA
R766 VRS-CY1JF333J~ X 33k 1/16W Metal Oxide AA R1067 VRS-CY1JF152J~ X 1.5k 1/16W Metal Oxide AA
R767 VRD-RA2BE103J~ X 10k 1/8W Carbon AA R1068 VRS-CY1JF331J~ X 330 1/16W Metal Oxide AA
R768 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA R1069 VRS-CY1JF152J~ X 1.5k 1/16W Metal Oxide AA
R802 VRS-CY1JF682J~ X 6.8k 1/16W Metal Oxide AA R1070 VRS-CY1JF331J~ X 330 1/16W Metal Oxide AA
R803 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA R1071 VRS-CY1JF152J~ X 1.5k 1/16W Metal Oxide AA
R804 VRS-CY1JF222J~ X 2.2k 1/16W Metal Oxide AA R1072 VRS-CY1JF221J~ X 220 1/16W Metal Oxide AA
R805 VRS-CY1JF222J~ X 2.2k 1/16W Metal Oxide AA R1073 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA
R806 VRS-CY1JF222J~ X 2.2k 1/16W Metal Oxide AA R1074 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
R807 VRS-CY1JF222J~ X 2.2k 1/16W Metal Oxide AA R1075 VRS-CY1JF331J~ X 330 1/16W Metal Oxide AA
R808 VRD-RA2BE273J~ X 27k 1/8W Carbon AA R1076 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
R810 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA R1081 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
R812 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA R1849 VRS-CY1JF222J~ X 2.2k 1/16W Metal Oxide AA
R814 VRS-CY1JF473J~ X 47k 1/16W Metal Oxide AA R1850 VRS-CY1JF472J~ X 4.7k 1/16W Metal Oxide AA
R815 VRS-CY1JF473J~ X 47k 1/16W Metal Oxide AA R1851 VRS-CY1JF221J~ X 220 1/16W Metal Oxide AA
R816 VRS-CY1JF223J~ X 22k 1/16W Metal Oxide AA R1852 VRS-CY1JF221J~ X 220 1/16W Metal Oxide AA
R817 VRS-CY1JF473J~ X 47k 1/16W Metal Oxide AA R1853 VRS-CY1JF221J~ X 220 1/16W Metal Oxide AA
R818 VRS-RG3AB151J+ X 150 1W Metal Oxide AB R1854 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
R823 VRD-RA2BE101J~ X 100 1/8W Carbon AA R1855 VRD-RA2BE102J~ X 1k 1/8W Carbon AA
R824 VRD-RA2BE101J~ X 100 1/8W Carbon AA R1861 VRS-CY1JF121J~ X 120 1/16W Metal Oxide AA
R826 VRD-RA2BE101J~ X 100 1/8W Carbon AA R1862 VRS-CY1JF121J~ X 120 1/16W Metal Oxide AA
R827 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
R828 VRS-CY1JF471J~ X 470 1/16W Metal Oxide AA BALUN
R829 VRS-CY1JF472J~ X 4.7k 1/16W Metal Oxide AA FB701 RBLN-0020CEZZ+ X Balun, BLN-0020CE AB
R830 VRS-CY1JF393J~ X 39k 1/16W Metal Oxide AA
R831 VRS-CY1JF271J~ X 270 1/16W Metal Oxide AA
R832 VRS-CY1JF822J~ X 8.2k 1/16W Metal Oxide AA SWITCHES
R833 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA S1001 QSW-K0202PEZZ+ X Switch, CH-Up AB
R835 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA S1002 QSW-K0202PEZZ+ X Switch, CH-Down AB
R836 VRD-RA2BE470J~ X 47 1/8W Carbon AA S1003 QSW-K0202PEZZ+ X Switch, VOL-Up AB
R838 VRS-CY1JF105J~ X 1M 1/16W Metal Oxide AA S1004 QSW-K0202PEZZ+ X Switch, VOL-Down AB
R839 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA S1005 QSW-K0202PEZZ+ X Switch, MENU AB
R840 VRS-CY1JF124J~ X 120k 1/16W Metal Oxide AA S1006 QSW-K0114CEZZ X Switch, POWER AC
R841 VRD-RA2BE821J~ X 820 1/8W Carbon AA
R842 VRS-CY1JF471J~ X 470 1/16W Metal Oxide AA MISCELLANEOUS PARTS
R843 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA å F701 QFS-C3229CEZZ X Fuse, T3. 15A 250V AB
R844 VRS-CY1JF185J~ X 1.8M 1/16W Metal Oxide AA å FH701 QFSHD1013CEZZ+ X Fuse Holder AA
R845 VRS-CY1JF185J~ X 1.8M 1/16W Metal Oxide AA å FH702 QFSHD1014CEZZ+ X Fuse Holder AA
R1002 VRS-CY1JF183J~ X 18k 1/16W Metal Oxide AA J401 QJAKGA015WJZZ X Jack, AE
R1003 VRS-CY1JF822J~ X 8.2k 1/16W Metal Oxide AA J402 QJAKE0108CEZZ X Jack, AB
R1006 VRS-CY1JF822J~ X 8.2k 1/16W Metal Oxide AA J403 QJAKE0183CEZZ X Jack, AB
R1007 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA J404 QJAKE0184CEZZ X Jack, AB
R1008 VRS-CY1JF183J~ X 18k 1/16W Metal Oxide AA J405 QJAKG0093CEZZ X Jack, AE
R1009 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA J406 QJAKFA008WJZZ X Jack, AC
R1021 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA P302 QPLGN0461CEZZA X Plug, 4Pin (S) AB
R1022 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA P407 QPLGN0361CEZZA X Plug, 3Pin (WO) AB
R1023 VRD-RA2BE271J~ X 270 1/8W Carbon AA P601 QPLGN0660CEZZ X Plug, 6Pin (K) AB
R1024 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA P602 QPLGN0461CEZZA X Plug, 4Pin AB
R1026 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA P603 QPLGN0361CEZZA X Plug, 3Pin (TP651~3) AB
R1027 VRS-CY1JF104J~ X 100k 1/16W Metal Oxide AA P701 QPLGN0260CEZZ X Plug, 2Pin (M) AB
R1031 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA P702 QPLGN0269GEZZ X Plug, 2Pin AB
R1032 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA P705 QTiPM0083CEZZ X Tip (SG) AB
R1034 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA P1001 QPLGN0561CEZZA X Plug, 5Pin AB
R1035 VRD-RA2BE101J~ X 100 1/8W Carbon AA P1002 QPLGN0561CEZZA X Plug, 5Pin (BC) AB
R1036 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA P1007 QPLGN0461CEZZA X Plug, 4Pin AB
R1037 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA P1008 QPLGN0461CEZZA X Plug, 4Pin AB
R1038 VRS-CY1JF562J~ X 5.6k 1/16W Metal Oxide AA P1011 QPLGN0361CEZZA X Plug, 3Pin AB
R1039 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA P1012 QPLGN0361CEZZA X Plug, 3Pin AB
R1040 VRD-RA2BE273J~ X 27k 1/8W Carbon AA RDA602 PRDAR0224PEFW X Heat Sink, Q602 AB
R1041 VRD-RA2BE103J~ X 10k 1/8W Carbon AA RDA501 PRDARA010WJFW X Heat Sink, IC501 AB
R1042 VRD-RA2BE101J~ X 100 1/8W Carbon AA RDA701 PRDARA026WJFW X Heat Sink, Q701 AD
R1043 VRS-CY1JF104J~ X 100k 1/16W Metal Oxide AA RDA301 PRDARA043WJFW X Heat Sink, IC301 AB
R1045 VRD-RA2BE101J~ X 100 1/8W Carbon AA RMC1001 RRMCU0222CEZZ X Remote Receiver AD
R1046 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA å RY701 RRLYJ0093CEZZ X Relay AE
R1047 VRS-CY1JF183J~ X 18k 1/16W Metal Oxide AA QCNW-A299WJZZ X Connecting Cord (K) AB
R1048 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA QCNW-A482WJZZ X Connecting Cord (DF) AD
R1049 VRS-CY1JF183J~ X 18k 1/16W Metal Oxide AA QCNW-A529WJZZ X Connecting Cord (YUV) AC
R1051 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA QCNW-A530WJN1 X Connecting Cord (AN) AC
R1052 VRS-CY1JF104J~ X 100k 1/16W Metal Oxide AA QCNW-A531WJN1 X Connecting Cord (FAV) AC
R1053 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA QCNW-A532WJN1 X Connecting Cord (RAV) AC
R1054 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA QCNW-A534WJN1 X Connecting Cord (MTS) AC
R1059 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA QCNW-A625WJZZ X Connecting Cord (P706) AB
R1061 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
R1062 VRS-CY1JF105J~ X 1M 1/16W Metal Oxide AA

45
21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTKA599WEA0 C3006 VCEA0A1CW106M+ X 10 16V Electrolytic AA

PWB-B CRT UNIT C3007 VCEA0A1HW475M+ X 4.7 50V Electrolytic AA
C3008 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
TRANSISTORS C3009 VCEA0A1CW227M+ X 220 16V Electrolytic AB
Q853 VS2SC3789//2E X 2SC3789 AB C3010 VCE9GA1HW475M+ X 4.7 50V Electrolytic AB
Q854 VS2SC3789//2E X 2SC3789 AB C3011 VCEA0A1HW475M+ X 4.7 50V Electrolytic AA
Q855 VS2SC3789//2E X 2SC3789 AB C3012 VCE9GA1HW475M+ X 4.7 50V Electrolytic AB
Q894 VS2SA1015Y/1E+ X 2SA1015Y AB C3013 VCKYCY1HB272K~ X 2700p 50V Ceramic AA
C3014 VCQYTA1HM473K+ X 0.047 50V Mylar AA
DIODES C3015 VCEACA1HC335K+ X 3.3 50V Electrolytic AB
D859 VHD1SS119//-1~ X 1SS119 AA C3016 VCE9GA1HW475M+ X 4.7 50V Electrolytic AB
D898 VHD1SS119//-1~ X 1SS119 AA C3017 VCEACA1CC106K+ X 10 16V Electrolytic AB
C3018 VCEA0A1HW105M+ X 1 50V Electrolytic AA
C3019 VCEA0A1CW106M+ X 10 16V Electrolytic AA
COIL
C3020 VCEA0A1CW106M+ X 10 16V Electrolytic AA
L851 VP-MK820K0000+ X Peaking, 82µH 10% AB
C3021 VCEA0A1CW106M+ X 10 16V Electrolytic AA
C3022 VCEA0A1CW106M+ X 10 16V Electrolytic AA
CAPACITORS C3023 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C851 VCKYPA1HB221K+ X 220p 50V Ceramic AA C3024 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
C852 VCKYPA1HB221K+ X 220p 50V Ceramic AA C3025 VCKYCY1HF473Z~ X 0.047 50V Ceramic AA
C853 VCKYPA1HB221K+ X 220p 50V Ceramic AA C3026 VCKYCY1HF473Z~ X 0.047 50V Ceramic AA
C880 RC-KZ0153CEZZ X 0.001 3.15KVCeramic AB C3030 VCQYTA1HM682K+ X 6800p 50V Mylar AA
C893 VCEA0A1CW336M+ X 33 16V Electrolytic AA C3031 VCKYCY1HF682Z~ X 6800p 50V Ceramic AA
C3034 VCEA0A1HW224M+ X 0.22 50V Electrolytic AA
RESISTORS C3037 VCEA0A1HW335M+ X 3.3 50V Electrolytic AA
R849 VRD-RA2BE271J~ X 270 1/8W Carbon AA C3038 VCEA0A1HW335M+ X 3.3 50V Electrolytic AA
R850 VRD-RA2BE470J~ X 47 1/8W Carbon AA C3039 VCEA0A1HW224M+ X 0.22 50V Electrolytic AA
R851 VRD-RA2BE470J~ X 47 1/8W Carbon AA C3042 VCKYCY1HB681K~ X 680p 50V Ceramic AA
R852 VRD-RA2BE470J~ X 47 1/8W Carbon AA C3043 VCKYCY1HB681K~ X 680p 50V Ceramic AA
R854 VRD-RA2BE331J~ X 330 1/8W Carbon AA C3044 VCEA0A1EW476M+ X 47 25V Electrolytic AA
R855 VRD-RA2BE331J~ X 330 1/8W Carbon AA C3045 VCEA0A1HW335M+ X 3.3 50V Electrolytic AA
å R859 VRS-VV3DB123J X 12k 2W Metal Oxide AA C3046 VCEA0A1HW335M+ X 3.3 50V Electrolytic AA
å R861 VRS-VV3DB123J X 12k 2W Metal Oxide AA C3047 VCEA0A1HW335M+ X 3.3 50V Electrolytic AA
å R863 VRS-VV3DB123J X 12k 2W Metal Oxide AA C3048 VCEA0A1HW335M+ X 3.3 50V Electrolytic AA
R864 VRD-RA2BE470J~ X 47 1/8W Carbon AA C3080 VCEA0A1CW106M+ X 10 16V Electrolytic AA
R876 VRD-RA2BE121J~ X 120 1/8W Carbon AA C3081 VCEA0A1CW106M+ X 10 16V Electrolytic AA
R877 VRD-RA2BE121J~ X 120 1/8W Carbon AA C3082 VCKYCY1HF103Z~ X 0.01 50V Ceramic AA
R878 VRD-RA2BE121J~ X 120 1/8W Carbon AA C3083 VCEAKA1CW106M+ X 10 16V Electrolytic AB
R880 VRD-RM2HD332J~ X 3.3k 1/2W Carbon AA
R881 VRD-RM2HD332J~ X 3.3k 1/2W Carbon AA RESISTORS
R882 VRD-RM2HD332J~ X 3.3k 1/2W Carbon AA R3001 VRS-CY1JF221J~ X 220 1/16W Metal Oxide AA
R889 VRD-RA2BE821J~ X 820 1/8W Carbon AA R3002 VRS-CY1JF221J~ X 220 1/16W Metal Oxide AA
R891 VRD-RA2BE561J~ X 560 1/8W Carbon AA R3003 VRS-CY1JF105J~ X 1M 1/16W Metal Oxide AA
R892 VRD-RA2BE391J~ X 390 1/8W Carbon AA R3004 VRS-CY1JF104J~ X 100k 1/16W Metal Oxide AA
R894 VRD-RA2BE152J~ X 1.5k 1/8W Carbon AA R3005 VRS-CY1JF623J~ X 62k 1/16W Metal Oxide AA
R895 VRD-RA2BE561J~ X 560 1/8W Carbon AA R3007 VRS-CY1JF332J~ X 3.3k 1/16W Metal Oxide AA
R3008 VRS-CY1JF302J~ X 3k 1/16W Metal Oxide AA
MISCELLANEOUS PARTS R3010 VRS-CY1JF392J~ X 3.9k 1/16W Metal Oxide AA
P860 QPLGN0461CEZZ X Plug, 4Pin AA R3011 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
P880 QPLGN0561CEZZ X Plug, 5Pin AB R3012 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
SC851 QSOCV0933CEZZ X Socket, AC R3013 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
R3014 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
R3016 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
DUNTKB271WEA1 R3018 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
PWB-E MTS MODULE UNIT R3019 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
R3021 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
INTEGRATED CIRCUITS R3024 VRS-CY1JF000J~ X 0 1/16W Metal Oxide AA
IC3001 VHiCXA2074Q-1S X CXA2074Q AP R3025 VRS-CY1JF272J~ X 2.7k 1/16W Metal Oxide AA
IC3002 VHiMM1501XN-1~ X MM1501XN AC R3026 VRS-CY1JF331J~ X 330 1/16W Metal Oxide AA
R3027 VRS-CY1JF392J~ X 3.9k 1/16W Metal Oxide AA
R3028 VRS-CY1JF683J~ X 68k 1/16W Metal Oxide AA
TRANSISTORS R3029 VRS-CY1JF392J~ X 3.9k 1/16W Metal Oxide AA
Q3001 VS2SD601AR/-1~ X 2SD601AR AA R3030 VRS-CY1JF683J~ X 68k 1/16W Metal Oxide AA
Q3002 VS2SD601AR/-1~ X 2SD601AR AA R3031 VRS-CY1JF182J~ X 1.8k 1/16W Metal Oxide AA
Q3004 VS2SD601AR/-1~ X 2SD601AR AA R3032 VRS-CY1JF223J~ X 22k 1/16W Metal Oxide AA
Q3005 VS2SD601AR/-1~ X 2SD601AR AA R3033 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
Q3006 VS2SD601AR/-1~ X 2SD601AR AA R3034 VRS-CY1JF182J~ X 1.8k 1/16W Metal Oxide AA
Q3007 VS2SD601AR/-1~ X 2SD601AR AA R3035 VRS-CY1JF223J~ X 22k 1/16W Metal Oxide AA
R3036 VRS-CY1JF102J~ X 1k 1/16W Metal Oxide AA
CAPACITORS R3080 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA
C3001 VCE9GA1HW475M+ X 4.7 50V Electrolytic AB R3081 VRS-CY1JF101J~ X 100 1/16W Metal Oxide AA
C3002 VCKYCY1HB562K~ X 5600p 50V Ceramic AA R3082 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
C3003 VCQYTA1HM123K+ X 0.012 50V Mylar AA R3083 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
C3004 VCEA0A1HW105M+ X 1 50V Electrolytic AA R3084 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA
C3005 VCEA0A1HW475M+ X 4.7 50V Electrolytic AA R3085 VRS-CY1JF103J~ X 10k 1/16W Metal Oxide AA

46
 21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

MISCELLANEOUS PARTS
P3001 QPLGZ0810CEZZ X Plug, 8Pin (M) AB
P3002 QPLGN0441CEZZ X Plug, 4Pin (RAV) AA CABINET PARTS LOCATION
P3003 QPLGN0441CEZZ X Plug, 4Pin (FAV) AA
P3004 QPLGN0361CEZZ X Plug, 3Pin (WF) AA
P3008 QPLGZ0810CEZZ X Plug, 8Pin (N) AB
P3009 QPLGZ0610CEZZ X Plug, 6Pin (SW) AB
P3012 QPLGN0241CEZZ X Plug, 2Pin (AV) AA
P3013 QPLGN0241CEZZ X Plug, 2Pin (AN) AA

MISCELLANEOUS PARTS

å ACC701 QACCZ3008PEZZ X AC Cord AE

SP301 VSP1205PB09WA X Speaker AK
LHLDK0014PEZZ X AC Cord Holder AB
LHLDW1047PEZZ X Wire Holder AB
LHLDZ0063PEZZ X Anode Clamp Holder AB
LHLDZA096WJZZ X Holder AB
LHLDZA107WJZZ X Holder AB
TCAUS3000GJZZ X Caution Label AA
XTASD30P12000 X Screw, x3 AA
XTASD40P16000 X Screw, x8 AA
XTASD40P20000 X Screw, x4 AA
QCNW-A871WJZZ X Connecting Cord AB
QCNW-A872WJZZ X Connecting Cord AC
QCNW-A873WJZZ X Connecting Cord AC
QPLGA0017CEZZ X Plug AC

SUPPLIED ACCESSORIES

ACCESSORIES
RRMCGA108WJSA X Infrared R-C AT
TiNS-A372WJZZ X Operation Manual AE

PACKING PARTS
(NOT REPLACEMENT ITEM)

SPAKCA318WJZZ - Packing Case AS

SPAKPA055WJZZ - Wrapping Paper AE
SPAKXA145WJZZ - Buffer Material AK
SSAKA0101GJZZ - Polyethylene Bag AB
TLABM0005GJZZ - Model Label AB
TLABZA153WJZZ - POP Label AK

CABINET PARTS

1 CCABAA146WEH0 X Front Cabinet Ass'y BC

1-1 Not Avairable - Front Cabinet —
1-2 HBDGB3155CESA X SHARP Badge AC
1-3 HDECQ119WJSA R/C Cover AC
1-4 JBTN-A070WJSA X Button, Power AC
1-5 MSPRC0005PEFW X Spring, for Power Button AA
1-6 GDORFA015WJSA X Door AE
1-7 MSPRPA012WJFW Door Spring AB
1-8 HiNDPA194WJSA X Indication Plate AB
1-9 GBFL-A007WJZZ X Baffle, x2 AC

2 GCABBA088WJKA X Rear Cabinet AX

47
21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PACKING OF THE SET

48
 21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

-MEMO-

49
21FL91

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

COPYRIGHT © 2002 BY SHARP CORPORATION

ALL RIGHTS RESERVED.

No part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.

TQ1456-S
Dec. 2002 Printed in Japan
In Japan gedruckt
Design and Production Information SHARP CORPORATION
Design : SEM AV Systems Group
Production : SEMEX Quality & Reliability Control Center
MY. DS Yaita, Tochigi 329-2193, Japan

50