COMPRESSOR SELECTION CRITERIA

Copyright Ó2001
All rights reserved.
No part of this document shall be reproduced in whole or in
part without the permission of SCA Australia Pty Ltd. This
includes reproduction or copies in any form or by any means
including photocopying, printing or electronic media.

IMPORTANT DISCLAIMER
This is an educational package in professional selection
guidelines using representative graphs, charts and tables.
Manufacturers specifications must be consulted for specific
guidelines and performance data. Unicla published data,
specific to all models is available via their promotional
literature and from SCA Australia Pty Ltd upon request.
Alternatively contact your Unicla supplier.

SCA Australia Pty Ltd and Unicla expressly disclaim all and
any liability and responsibility to any person or business as a
result of any actions taken on the basis of information in this
publication.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 1 of 21
 COMPRESSOR SELECTION CRITERIA
Introduction
System design, including the compressor to be used, is based on a heat load calculation
conducted for the environment we are aiming to cool and dehumidify.

In professional design this is done using test vehicles in environmental chambers where heat
loads can be controlled, together with, and based on, theoretical calculation.

Technicians reading this bulletin must be familiar with reading a pressure / temperature
relationship chart to identify evaporating and condensing temperatures from gauge readings.

Definitions
HEAT

Heat is a form of energy. In this application heat will be defined as both temperature and
humidity contained within a nominated environment. (ie: the cabin).

CAPACITY

The capacity of the system is the amount of heat that the system is capable of removing from a
nominated environment (ie: the cabin). This includes the cooling and dehumidification of that
environment.

ENTHALPY

Enthalpy is the sum of the energy (heat) applied to a medium. Enthalpy is often referred to as
the total heat content of a substance. In this application Enthalpy will relate to the amount of
heat absorbed by the refrigerant as it passes through the evaporator.

The purpose of this guidelines document is to enable you to gain an appreciation of system
design and the importance of correct compressor selection in ensuring adequate capacity of the
system to cater for the heat loads under which the system will operate.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 2 of 21
Relationship Between Cooling Capacity And Heat Load
When entering a vehicle that has been parked in the sun or when a vehicle is operating in areas
of high temperature and / or high humidity the heat load is high. ÒHeat LoadÓ is Temperature
and Humidity. As the system continues to operate the heat load will reduce as the air is cooled
and dehumidified.

With the high heat loads the cooling capacity of the system is inadequate to instantly reduce the
cabin temperature down to a desirable level (ie 20¼C). With the continued operation the
progressive reduction in heat load will enable the cooling capacity of the system to increase
(with respect to attaining desired cabin temperatures). When we reach balancing point (B.P.)
the capacity of the system exceeds the heat load and we are capable of cooling the cabin to
specified levels or below.

Any system must be capable of reaching B.P. to ensure adequate cabin cooling and
customer satisfaction at predetermined heat loads within an acceptable time frame Ð this
is commonly referred to as the pull down test (see graph 2).

Heat Load Cooling Capacity

Cooling Capacity kcal/hr
Heat Load

BP

60 40 20¼C

Cabin Temperature
GRAPH 1 COOLING CAPACITY VERSES HEAT LOAD

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 3 of 21
 60
CABIN TEMPERATURE ¼C

40

20

10 20 30 40
TIME (MINUTES)

GRAPH 2 PULL DOWN PERFORMANCE

(Initial Cabin Temperature 60¼C at 45% R.H.)

System Design
To enable B.P. to be reached within an acceptable time frame the capacity of the system must
cater for

Ø Initial Òheat soakÓ (vehicle parked Ð direct sunlight)

And
Ø Constant heat loads on the cabin environment
Namely
Ø Transmission heat radiated through glass
Ø Entry heat via floor / firewall etc.
Ø Entry heat via ventilation (flow through / natural ventilation
Ø Internal generated heat by human body
Ø Internal generated heat Ð vehicle componentry

Table 1 (over) gives an example of the heat Quantities for a small / medium passenger vehicle
of modern design (Actual data Ð use as example only)
Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 4 of 21
 TABLE 1 Ð HEAT LOAD QUANTITIES

OPERATING CONDITIONS

Ambient Temperature - 35¼C

Relative Humidity - 60%
Interior Temperature - 25¼C
Vehicle Speed - 40 km / h
Sunlight Conditions - Bright

All units in kcal / hr

Heat
Transmitted Entry Heat Internal
Entry Heat Generated by Total Heat
Heat Through Floor Generated
(Ventilation) Occupants Load
Glass Firewall etc Heat
(x4)
1370 490 320 400 110 2690

To cater for the above heat loads and additional heat soak the system must:
Have refrigerant in the evaporator at a sufficiently low Temperature to enable it to absorb heat
from the cabin air

And

Have a sufficient quantity of refrigerant flowing through the evaporator.

Therefore

LetÕs work from the evaporator to determine system capacities.

The evaporator is the basis for capacity calculation Ð it is the component directly
responsible for absorbing heat energy from the cabin.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 5 of 21
Capacity Ratings
Refrigeration capacity has historically been loosely referred to in Tons of refrigeration based on
a 24 hour period.

1 ton of Refrigeration is the amount of heat required to melt one ton of ice. If we are going to
use tons of refrigeration as a measurement of the capacity of a system strictly it must be time
referenced, normally to an hour rating.

1 Ton of Refrigeration = 288,000 BTUÕs

or
72,528 Kilocalories

This is the amount of energy required to melt the one ton of ice (based on a 24 hour period)

Therefore 288,000 BTUÕs ¸ 24 = 12,000 BTUÕs / hr

72,528 kcal ¸ 24 = 3,022 kcal / hr

We have now arrived at a capacity rating for systems

1 Ton = 12,000 BTU / hr

= 3,022 kcal / hr

Alternatively the capacity may be rated in Watts or kilowatts

1 Ton = 3,517 watts or 3.517 kilowatts

TABLE 2
REFRIGERATING CAPACITIES Ð CROSS REFERENCE CHART

TONS OF
.5 1 1.5 2 2.5 3 3.5 4
REFRIGERATION

kcal/ hr 1511 3022 4533 6044 7555 9066 10577 12088

BtuÕs / hr 6000 12000 18000 24000 30000 36000 42000 48000

kW 1.758 3.517 5.275 7.034 8.792 10.551 12.309 14.068

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 6 of 21
Application Chart - Refrigeration Capacities
- Air Conditioning applications R134a at 0¼C
To be used for approximation purposes only

.5 Ton Special application Ð low capacity Ð (ice box, small compartment cooling)
1Ton Small / compact vehicles / low heat load / preferably tinted windows
1.5 Ton Medium vehicles Ð common evaporator capacity / size
2.0 Ton Large vehicles Ð higher capacity Ð higher heat loads
Larger vehicles / station wagons / high glass surface area applications
2.5 Ton
- ie agricultural / plant
Over 2.5 Ton Special application only Ð bus / locomotive etc.

SPECIAL NOTES
Evaporator ratings may be stamped / plated onto the unit or evaporator coil itself or available ex
manufacturer or specified in parts manuals / promotional literature in BtuÕs / kW / kcal / hr.

Alternatively the part number may relate to the capacity of the unit ie RT9E may be roof top unit
9 kW capacity Ð Externally equalized TX Valve.

Designing the System

Now we have a reference for system capacity we can design and manufacture an evaporator
with a rating in accordance with the calculated heat load on the system.

The capacity of the evaporator ie 16,000 BTU / hr 4030 kcal / hr will be determined principally by

Ø The surface area (size, fin design etc) of the evaporator

Ø The amount of refrigerant flowing through it (tube design size, number of runs etc)
Ø The temperature differential between the air and the refrigerant
Ø The volume of air flowing over the fins / tubes

To accurately calibrate evaporators the heat load and refrigerant temperature are referenced ie:

Ø 35¼C intake air

Ø 40% Relative Humidity (R.H.)
Ø 0¼C Vaporization temperature
Ø 5¼C Superheat.
NOTE: The intake air and R.H. are often listed as a Dry Bulb and Wet Bulb temperature from
which a psychometric chart can be used to determine R.H.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 7 of 21
Of these factors the critical one is the amount of refrigerant flowing through the evaporator.

If - the refrigerant to air differential is high

And
- there is the required volume of air flowing over the evaporator to Òload itÓ with heat
Then
The variable that will determine the efficiency and capacity of the unit is the
volume of refrigerant flowing through the evaporator coil.

Remember:

It is the refrigerant that absorbs the heat Ð therefore refrigerant flows must be optimized.

System Capacity verses Flow

With the evaporator at a nominated capacity in accordance with its calculated heat loads we
must now design the rest of the system to provide adequate flow of refrigerant to achieve itÕs
capacity. We must also ensure the condenser is of adequate capacity to dissipate all heat
absorbed from the cabin.

Basic Component Function

THE HEAT EXCHANGERS:
Evaporator - Absorbs heat from inside the cabin (or a nominated environment)

Condenser - Radiate all heat absorbed into the refrigerant by the evaporator, in the
suction run and in the process of compression (superheat of compression)

THE FLOW CONTROLLERS

TX Valve / Orifice Tube - Ensures adequate flow into the evaporator (and subsequently
through the evaporator) to cater for maximum heat loads Ð TX
flow matches evaporator rating
Compressor - Must be capable of circulating a sufficient volume of
refrigerant to maintain maximum flow rates through the
evaporator to achieve full system capacity

ALL COMPONENTS ARE IMPORTANT FROM A SYSTEM DESIGN / SYSTEM MATCHING

PERSPECTIVE BUT IT IS THE COMPRESSOR THAT MUST PROVIDE THE FLOW TO
OPTIMIZE THE EFFICIENCY OF ALL COMPONENTS Ð THEREFORE THE COMPRESSOR
SELECTION BECOMES CRITICAL AND MUST BE RATED TO THE SYSTEM IN WHICH IT
WILL OPERATE.
Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 8 of 21
Compressor Selection
The compressor has 2 principle functions in respect to the circulation of refrigerant
It must:
Ø Discharge refrigerant into the condenser against the head pressure (high side pressure)
(determined in principle by the ambient temperature)
and
Ø Pull refrigerant through the evaporator (via the suction) to provide a nominated saturation
temperature / pressure at an adequate flow rate. (ie. To pull the refrigerant temperature
down)
Therefore the calibration of a compressor must be against a given standard. The flow rate will
vary depending on the conditions in which the compressor is placed (see over).
These conditions are often specified in the compressor performance graphs, which must be
referred to in the selection process of the compressor
GRAPH 3 COMPRESSOR PERFORMANCE - EXAMPLE
12
OPERATING CONDITIONS

10 P. Suction 1.86 kg / cm2G

Capacity x 1000 kcal / hr

P. Discharge 15.5 kg / cm2G

Super Heat 10.0 deg. C
8 Sub Cool 5.0 deg. C
Evap. Temp. 0.0 deg. C

6 SPECIFICATIONS

Model SAMPLE
Displacement 200 cc/rev.
4 Cylinders 10
Max. speed 4,500 r.p.m.

2 1 kg / cm2 = 100 kPa (approx)

= 14.7 PSI (approx)

0 1 2 3 4

Compressor speed (x 1/000 r/min)

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 9 of 21
From graph 3 we can now relate compressor performance to system design and specifications
and the conditions under which it will operate.
Taking them one item at a time.

Discharge Pressure
The specified discharge pressure in this example is 15.5 kg/cm2G (1520kPaG) (220psig)
In an R134 application this corresponds to a condensing temperature of 65¼C (R134a)
Therefore
This condenser is calibrated to deliver its specified performance under a condensing pressure of
15.5 kg/cm2G (60¼C Condensing Temperature) (Refer to pressure / temperature chart) which
using industry standards relate to an ambient (day) temperature of approximately 30¼C
Therefore
This compressor will deliver performance, as specified on a 30¼C day providing condensing is
adequate.

A drop in condensing performance with a corresponding rise in head pressure and

condensing temperature will reduce system capacity against the graph specification.

Suction Pressure
With a specified suction pressure of 1.86 kg / cm 2 G (182 kPaG) (27 psig) the refrigerant
vaporization (evaporating) temperature is 0¼C. We can therefore deduct this compressor is
matched to medium temperature application ie R134a where an evaporating temperature of 0¼ is
ÒnormalÓ.

As an alternative to specifying a suction pressure an evaporating temperature may be the

published operating condition for the compressor.
ie: Instead of specifying Òsuction Pressure 1.86 kg / cm2GÓ
The specification will be ÒEvaporating Temperature 0¼CÓ

SPECIAL NOTE Ð LOW TEMPERATURE APPLICATIONS

For technicians selecting compressors for low temperature applications additional

graphs are available on request that give performance data for specified sub zero
applications. (usually in the form of a multiple plot graph). These are not openly
distributed due to their complexity and special application. If they are required contact
SCA Australia Pty Ltd with specifics detailing your requirements including refrigerant to
be used.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 10 of 21
Superheat And Subcool Specifications

Superheat and subcool specifications are detailed as a calibration parameter for the compressor
since they both have an effect on the capacity of the system. The graphed system capacity is
based on the system having a superheat of 10¼C and a subcool of 5¼C Ð an increase in either of
these will have a direct effect on system capacity. For compressor selection purposes these
readings are indicative of a Ònormal systemÓ and are of minor significance in compressor
selection unless either condition is significantly different than specified.

READING THE GRAPHS / DATA

Performance / Capacity Graph Interpretation

The performance / capacity graph principally indicates the level of performance from the
compressor corresponding to itÕs speed. To ensure the reliability and validity of this data the
operating conditions under which it is operating must be identified and related to the service
environment into which it is being placed. These operating conditions are the previously stated
head pressure (the pressure the compressor is working against) the suction pressure /
evaporating temperature, superheat and subcooling levels and most importantly the refrigerant
in the system.

In principle reading the graph is simple. The size or capacity of the evaporator or TX
Valve size can be directly related to the graph to correlate the speed at which evaporator /
system capacity will be achieved. (ie when the compressor is providing adequate flow
through the system).

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 11 of 21
 GRAPH 4 COMPRESSOR PERFORMANCE 1

10 OPERATING CONDITIONS

P. Suction 1.86 Kg / cm2G

Capacity x 1000 kcal / hr

8 P. Discharge 15.5 Kg / cm2G

Super Heat 10.0 deg. C
Sub Cool 5.0 deg. C
6 Evap. Temp. 0.0 deg. C

4 SPECIFICATIONS
Model SAMPLE
Displacement 115 cc/rev.
2 Cylinders 10
Max. speed 7,000 r.p.m.

0 1 2 3 4

Compressor speed (x 1/000 r.p.m)

From this graph it can be observed that a system fitted with a 5.3 kW evaporator coil (= 4,550
kcal / hr = 1.5 Ton refrigerating effect) will not provide adequate capacity until a compressor
speed of approximately 2,500 r/min.
A 6.8 kW evaporator coil (5,840 kcal / hr = 1.93 ton refrigerating effect) will require a compressor
speed of approximately 3,100 r/min.
In essence the performance graph is simply indicating the speed at which the system capacity
matches the compressor capacity, which in turn is compared to the operating conditions under
which the system normally operates.
LetÕs use a selection example using the graph above (Graph 4) and compare it to Graph 5 (over)
A 6.8 kW (5,840 kcal / hr) system operating at 2,500 r / min governed speed and a drive ratio of
1:1 will produce an effective performance of 5.2 kW (4,500 kcal / hr.) If the system has been
designed on a heat load calculation basis then performance levels will be substandard under this
operating condition) (ie it does not achieve the 6.8 kW 5840 kcal / at is rated speed.
The next compressor (Graph 5) has a performance graph which indicates the 6.8 kW
(5,840ÊkcalÊ/ hr) capacity is achieved at approximately 1,700 r / min. For this operating condition
this is the compressor of choice.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 12 of 21
GRAPH 5 COMPRESSOR PERFORMANCE 2
12

OPERATING CONDITIONS
10
Capacity x 1000 kcal / hr

P. Suction 1.86 Kg / cm2G

8 P. Discharge 15.5 Kg / cm2G
Super Heat 10.0 deg. C
Sub Cool 5.0 deg. C
6 Evap. Temp. 0.0 deg. C

SPECIFICATIONS
4 Model SAMPLE
Displacement 200 cc/rev.
Cylinders 10
2 Max. speed 4,500 r.p.m.

NOTE:
All or selected items may be published
dependent on the compressor and its
0 1 2 3 4 application.
Compressor speed (x 1/000 r/min)

Refrigerant Flow Characteristics

Refrigerant flow characteristics are not normally published because the principle factor in
selection of the compressor is the match between capacity and speed (as previously stated Ð
read directly off the capacity graph).
However
To fully appreciate the necessity to match compressors to systems and their operating
conditions we will present test data that relates to refrigerant flows against compressor speed.

When an evaporator is rated there are a number of operating conditions attached (see
specifications over) but the most critical in its relationship to the compressor is the flow rating of
the evaporator.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 13 of 21
 Evaporator Specifications Ð Sample Only

COIL SPECIFICATIONS
Coil Type - Sample only
Tub Type - Rifled Bore
Fin Height - 150mm
Fin Length - 495 mm
No of Rows - 5.0
Fins / Metre - 510
No of Circuits - 3.0
Fin material - Aluminum
Evaporating Temp. - 0¼C
Superheat - 5¼C
Airflow 1/5 - 187
Liquid Temp - 48¼C
Refrigerant - R134a

RATINGS
Capacity - 6.8 kW 5,840 kcal / hr Flow Rating
Refrigerant Flow - 3.2 kg / min - the critical factor
Refrigerant Charge - 0, 1 kg
Pressure Drop (oil) - 67.2 kPa
(header) - 14.0 kPa
Air Pressure Drop - 190 Pa
Leaving Vapor Velocity - 16.5 m/s

If we now relate this to the flow ratings of the compressor (under the previously mentioned head
pressure, suction pressure, superheat, subcool conditions) we can draw some conclusions

TABLE 4 COMPRESSOR FLOW VERSES CAPACITY

Sample Only

COMPRESSOR (R/MIN) REFRIGERANT FLOW COOLING CAPACITY

1000 1.66 Kg/min 2.9 kW (2,490 kcal / hr)
1500 2.71 Kg/min 5.8 kW (5,000 kcal / hr)
2000 3.51 Kg/min 7.7 kW (6,650 kcal / hr)
2500 4.13 Kg/min 9.6 kW (8,300 kcal / hr)
3000 4.35 Kg/min 10.5 kW (9,000 kcal / hr)

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 14 of 21
From Table 4 it can be clearly seen the flow rating at 1000 and 1500 r / min is below the
specified rating of the evaporator Ð we need 3.2kg of refrigerant flow. We only have 1.66 kg/m
at 1000 and 2.71 kg/m at 1500 r/min.

Remember

It is the refrigerant flowing through the evaporator that absorbs heat from the cabin. At lower
flow rates evaporator and system capacities are dramatically reduced Ð There is simply not
enough refrigerant flow at 1,000 and 1500 r / min.

This is the principle reason for performance losses at idle.

At approximately 1800 r/min the refrigerant flow is at 3.2 kg/min. This matches the flow rating of
3.2 kg / min specified in the evaporator coil design to attain an efficiency of the specified 6.8 kW
(5,840 kcal / hr). Above this speed evaporator flows are assured therefore system
performance is optimized.

Inadequate refrigerant flow as a result of the fitment of an undersize compressor will limit
performance at all speeds where the refrigerant flow through the evaporator is below the
specified value.

In reality flow ratings are normally not referred to in compressor selection, - it is simply a match
between the capacity of the compressor and the system Ð it is however important to realize the
controlling factor in capacity attainment is the flow.

ADDITIONAL METHODS OF COMPRESSOR MATCHING

In the absence of technical data, compressor selection is often done via Òfield serviceÓ methods.

METHOD 1 Ð TX VALVE SIZE

With a known TX Valve or orifice size the effective maximum capacity of the evaporator can be
presumed.

Example:

The previous evaporator with a 6.8 kW rating would normally have a 2 Ton valve fitted to ensure
adequate evaporator filling under maximum design heat load.

1 Ton = 3.517 kW
1.5 Ton = 5.275 kW
2 Ton = 7.034 kW

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 15 of 21
Therefore with reference to the performance chart ( table 4) the 7.034 kW is obtained at just
below 2000 r/min. Even though it is only a 6.8 kW coil in the absence of that specification the
TX is the only form of capacity measurement we have Ð even though it is slightly higher than the
actual capacity of the system it is a guide to compressor selection.

Method 2 - Low Side Pressure

In the absence of any data, low side pressures can be used as an indicator of compressor
capacity and / or efficiency. The inability to Òpull downÓ the low side to acceptable / normal levels
may indicate a compressor with the inability to pull refrigerant through the evaporator at an
acceptable rate comparative to the feed rate of the TX Valve or Orifice Tube. Whilst this is a
common practice there are considerable dangers associated with it Ð as presented here.

Since the low side pressure is determined in principle by the TX valve feed rate compared to the
evaporator pull rate (suction) it must be validated that the TX is the correct size, calibrated
correctly, being ÒfedÓ with liquid at nominated pressures and charge rates correct.

In addition to the variable flow of the TX Valve / Orifice Tube, evaporator and suction line
pressure drops can make this form of compressor capacity validation virtually useless. A
vehicle fitted with an evaporator or suction line exhibiting high pressure drop can lead to the
low side ÒpullingÓ extremely low in normal operation. With an undersize compressor and
this condition the low side pressures may appear ÒnormalÓ Ð whereas in reality it is a system with
high evaporator / suction line pressure drops coupled to an ineffective / undersize compressor.
If the compressor is the correct size the low side will pull extremely / abnormally low because of
the pressure drop in this case.

Pressure analysis should only be used by experienced technicians with substantial associated
testing for TX flow rates, pressure / temperature drop analysis etc.

Dual Evaporator Systems

When fitting compressors to dual evaporator systems the total net capacity of both evaporators
must be the basis for compressor selection.

Example

System is fitted with 2 x 4,300 kcal / hr evaporators (2 x 5kW) (2 x 1.5 Ton TX Valves)

Ø Total system capacity = 8,600 kcal / hr 10kW).

Ø Operating conditions Ð city cycle vehicle
Ø Operating speed at 1500 Ð 2000 r / min. average

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 16 of 21
From the two graphs (over - page 16. )

Compressor 2 is the compressor of choice. Fitting of compressor 1 will only provide for a total
capacity of 6000 Ð 7600 kcal at the nominated speed of 1500 Ð 2000 r/min.

Compressor 2 provides a capacity of 8,000 Ð 9,600 kcal / hr Ð adequate for peak efficiency at
the nominated compressor speed.

GRAPH 6 COMPRESSOR 1 PERFORMANCE

12 OPERATING CONDITIONS

10 P. Suction 1.86 Kg / cm2G

Capacity x 1000 kcal / hr

P. Discharge 15.5 Kg / cm2G

Super Heat 10.0 deg. C
8 Sub Cool 5.0 deg. C
Evap. Temp. 0.0 deg. C
6
SPECIFICATIONS

4
Model SAMPLE
Displacement 200 cc/rev.
2 Cylinders 10
Max. speed 4,500 r.p.m.

1 2 3 4 NOTE:
All or selected items may be
Compressor speed (x 1/000 r/min) published dependent on the
compressor and its application

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 17 of 21
 GRAPH 7 COMPRESSOR 2 PERFORMANCE

14 OPERATING CONDITIONS

P. Suction 1.86 Kg / cm2G

12 P. Discharge 15.5 Kg / cm2G
Capacity x 1000 kcal / hr

Super Heat 10.0 deg. C

10 Sub Cool 5.0 deg. C

8
SPECIFICATIONS

6 Model SAMPLE
Displacement 313 cc/rev.
4
Cylinders 10
Max. speed 4,500 r.p.m.
2

0 1 2 3 4

Compressor speed (x 1/000 r/min)

CAUTIONARY NOTES Ð DUAL EVAPORATORS

On dual evaporator systems with one circuit isolated (normally done by a magnetic switching
valve). The low side may pull abnormally low. Careful system design and compressor matching
is required to ensure the low side does not pull into a vacuum in this position. A balance
between efficiency and maintaining position low side pressure is a requirement of compressor
selection in many dual evaporator systems. Ie a large capacity compressor may achieve good
efficiency for a vacuum Ð this is an undesirable condition. An oil separator may be required in
dual evaporator systems.

Power Consumption Graphs

Power consumption graphs relate to the input required to drive the compressor across its speed
range, measured in horsepower or kilowatts. The same operating conditions apply as for the
previous capacity graph since the input requirements to drive the compressor will vary
significantly depending on the amount of work it is doing. (ie the amount of head pressure it is
working against, the volume of suction refrigerant etc).

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 18 of 21
The power consumption graph is principally used in standby applications where an electric motor
is being used to drive the pump at a nominated r/min. By referring to this graph a standby motor
selection can be made and drive ratioÕs calculated.

GRAPH 8 COMPRESSOR POWER CONSUMPTION

8
Power consumption (PS) (KW)

OPERATING CONDITIONS

P. Suction 1.86 Kg / cm2G

6
P. Discharge 15.5 Kg / cm2G
Super Heat 10.0 deg. C
Sub Cool 5.0 deg. C
4
Evap. Temp. 0.0 deg. C

SPECIFICATIONS
2
Model SAMPLE
Displacement 200 cc/rev.
Cylinders 10
0 1 2 3 4 Max. speed 4,500 r.p.m.
Compressor speed (x 1/000 r/min)

Coefficient of Performance Ð (COP) Graphs

COP graphs are normally plotted on a power consumption and capacity graph.

COP is the ratio between the output (measured in cooling capacity) and the input required to
drive the compressor (power consumption). COP in simple terms is output compared to input.

If we input 2.1 kW and output 3.15 kW the COP is 1.5. This COP value will vary with
compressor speed since the dynamics of the system will change as flow rates, internal
resistances, heat absorption and rejection rates etc vary.

A principle factor in COP is the refrigerant being used and the conditions under which the test is
being conducted. All testing must be against a standard as previously identified.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 19 of 21
 Compressor Capacity & Horsepower Graph

Refrigerating Capacity & Power Consumption

8.0
2.0
C.O.P

6.0
(kW)

Refrigerating
1.5

C.O.P.
Capacity

4.0

1.0
Power
Consumption
2.0

0.5

0.0 1,000 2,000 3,000 0.0

COMPRESSOR SPEED - RPM

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 20 of 21
 SUMMARY Ð COMPRESSOR SELECTION

The principle selection criteria is the capacity of the compressor must match
the capacity of the evaporator(s) (system) under the nominated operating
conditions (compressor speed)

Insufficient flow rates at lower compressor speeds will result in dramatically

reduced capacity of the system.

In the absence of system capacity / evaporator capacity data the TX Valve

size may be used as an indicator of capacity. The TX should be sized to
adequately fill the coil under full heat loads.

Low side pressure analysis should not be used in isolation as a method of

determining compressor size / capacity due to the variables of pressure drop
/ TX flow rates etc.

Dual Evaporator systems will require a compressor with adequate capacity

to cater for both evaporators at nominated compressor speeds.

Power consumption graphs are used to ascertain drive motor capacity /

input power requirements.

Coefficient of Performance (COP) graphs show the output compared to the

input across the operating range of the compressor for a nominated
refrigerant.

Copyright Ó2001. All rights reserved. No part of this document shall be reproduced in whole or in part
without the permission of SCA Australia Pty Ltd. SCA Australia Pty Ltd and Unicla expressly disclaim
all and any liability and responsibility to any person or business as a result of any actions taken on the
basis of information in this Bulletin. Manufacturers specifications must be consulted for specific
guidelines and performance data.
PAGE 21 of 21