60 Series - General purpose relays 6 - 10 A

Features 60.12 60.13

Plug-in mount
10 A General purpose relay
• 2 & 3 pole changeover contacts
• Cadmium Free contacts (preferred version)
• AC coils & DC coils
• UL Listing (certain relay/socket combinations)
• Contact material options
• Lockable test button with mechanical flag
indicator (preferred version)
• 90 series sockets
• 2 pole, 10 A power contacts • 3 pole, 10 A power contacts
• Coil EMC suppression • 8 pin plug-in • 11 pin plug-in
• Timer accessories 86 series

FOR UL HORSEPOWER AND PILOT DUTY RATINGS

SEE “General technical information” page V
Contact specification
Contact configuration 2 CO (DPDT) 3 CO (3PDT)
Rated current/Maximum peak current A 10/20 10/20
Rated voltage/Maximum switching voltage V AC 250/400 250/400
Rated load AC1 VA 2,500 2,500
Rated load AC15 (230 V AC) VA 500 500
Single phase motor rating (230 V AC) kW 0.37 0.37
Breaking capacity DC1: 30/110/220 V A 10/0.4/0.15 10/0.4/0.15
Minimum switching load mW (V/mA) 500 (10/5) 500 (10/5)
Standard contact material AgNi AgNi
Coil specification
Nominal voltage (UN) V AC (50/60 Hz) 6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC 6 - 12 - 24 - 48 - 60 - 110 -125 - 220
Rated power AC/DC VA (50 Hz)/W 2.2/1.3 2.2/1.3
Operating range AC (0.8…1.1)UN (0.8…1.1)UN
DC (0.8…1.1)UN (0.8…1.1)UN
Holding voltage AC/DC 0.8 UN/0.5 UN 0.8 UN/0.5 UN
Must drop-out voltage AC/DC 0.2 UN/0.1 UN 0.2 UN/0.1 UN
Technical data
Mechanical life AC/DC cycles 20 · 106/50 · 106 20 · 106/50 · 106
3
Electrical life at rated load AC1 cycles 200 · 10 200 · 103
Operate/release time ms 9/9 9/9
Insulation between coil and contacts (1.2/50 µs) kV 4 3.6
Dielectric strength between open contacts V AC 1,000 1,000
Ambient temperature range °C –40…+70 –40…+70
Environmental protection RT I RT I
Approvals (according to type)

1
 60 Series - General purpose relays 6 - 10 A
Features 60.12 - 5200 60.13 - 5200
Plug-in mount - 6 A
Bifurcated contacts for low level switching
• 2 & 3 pole changeover contacts
• Cadmium Free contacts
(Gold plated Silver Nickel)
• AC coils & DC coils
• Lockable test button with mechanical flag
indicator (preferred version)
• 90 series sockets
• Coil EMC suppression
• 2 pole, 6 A bifurcated contacts • 3 pole, 6 A bifurcated contacts
• Timer accessories 86 series
• 8 pin plug-in • 11 pin plug-in

FOR UL HORSEPOWER AND PILOT DUTY RATINGS

SEE “General technical information” page V
Contact specification
Contact configuration 2 CO (DPDT) 3 CO (3PDT)
Rated current/Maximum peak current A 6/10 6/10
Rated voltage/Maximum switching voltage V AC 250/400 250/400
Rated load AC1 VA 1,500 1,500
Rated load AC15 (230 V AC) VA 250 250
Single phase motor rating (230 V AC) kW 0.185 0.185
Breaking capacity DC1: 30/110/220 V A 6/0.3/0.12 6/0.3/0.12
Minimum switching load mW (V/mA) 50 (5/5) 50 (5/5)
Standard contact material AgNi + Au (5 µm) bifurcated contacts AgNi + Au (5 µm) bifurcated contacts
Coil specification
Nominal voltage (UN) V AC (50/60 Hz) 6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC 6 - 12 - 24 - 48 - 60 - 110 -125 - 220
Rated power AC/DC VA (50 Hz)/W 2.2/1.3 2.2/1.3
Operating range AC (0.8…1.1)UN (0.8…1.1)UN
DC (0.8…1.1)UN (0.8…1.1)UN
Holding voltage AC/DC 0.8 UN/0.5 UN 0.8 UN/0.5 UN
Must drop-out voltage AC/DC 0.2 UN/0.1 UN 0.2 UN/0.1 UN
Technical data
Mechanical life AC/DC cycles 20 · 106/50 · 106 20 · 106/50 · 106
Electrical life at rated load AC1 cycles 250 · 103 250 · 103
Operate/release time ms 9/9 9/9
Insulation between coil and contacts (1.2/50 µs) kV 4 3.6
Dielectric strength between open contacts V AC 1,000 1,000
Ambient temperature range °C –40…+70 –40…+70
Environmental protection RT I RT I
Approvals (according to type)

2
 60 Series - General purpose relays 6 - 10 A
Features 60.62 60.63
Flange mount - General purpose relay 10 A
• Faston 187, 4.8x0.8 mm
• 2 & 3 pole changeover contacts
• AC coils & DC coils
• Cadmium Free contacts (preferred version)
• Contacts material options

• 2 pole, 10 A power contacts • 3 pole, 10 A power contacts

• Flange mount/Faston 187 • Flange mount/Faston 187

FOR UL HORSEPOWER AND PILOT DUTY RATINGS

SEE “General technical information” page V
Contact specification
Contact configuration 2 CO (DPDT) 3 CO (3PDT)
Rated current/Maximum peak current A 10/20 10/20
Rated voltage/Maximum switching voltage V AC 250/400 250/400
Rated load AC1 VA 2,500 2,500
Rated load AC15 (230 V AC) VA 500 500
Single phase motor rating (230 V AC) kW 0.37 0.37
Breaking capacity DC1: 30/110/220 V A 10/0.4/0.15 10/0.4/0.15
Minimum switching load mW (V/mA) 500 (10/5) 500 (10/5)
Standard contact material AgNi AgNi
Coil specification
Nominal voltage (UN) V AC (50/60 Hz) 6 - 12 - 24 - 48 - 60 - 110 - 120 - 230 - 240 - 400
V DC 6 - 12 - 24 - 48 - 60 - 110 -125 - 220
Rated power AC/DC VA (50 Hz)/W 2.2/1.3 2.2/1.3
Operating range AC (0.8…1.1)UN (0.8…1.1)UN
DC (0.8…1.1)UN (0.8…1.1)UN
Holding voltage AC/DC 0.8 UN/0.5 UN 0.8 UN/0.5 UN
Must drop-out voltage AC/DC 0.2 UN/0.1 UN 0.2 UN/0.1 UN
Technical data
Mechanical life AC/DC cycles 20 · 106/50 · 106 20 · 106/50 · 106
3
Electrical life at rated load AC1 cycles 200 · 10 200 · 103
Operate/release time ms 9/9 9/9
Insulation between coil and contacts (1.2/50 µs) kV 4 3.6
Dielectric strength between open contacts V AC 1,000 1,000
Ambient temperature range °C –40…+70 –40…+70
Environmental protection RT I RT I
Approvals (according to type)

3
 60 Series - General purpose relays 6 - 10 A
Ordering information
Example: 60 series plug-in relay, 3 CO (3PDT), 12 V DC coil, test button and mechanical indicator.

A B C D

6 0 . 1 3 . 9 . 0 1 2 . 0 0 4 0
Series A: Contact material D: Special versions
Type 0 = Standard 0 = Standard
1 = 8/11 pin plug-in 2 = AgCdO C: Options
6 = Faston 187 (4.8x0.8 mm) 5 = AgNi + Au (5 µm) 0 = None
with flange mount B: Contact circuit 2 = Mechanical indicator
No. of poles 0 = CO (nPDT) 3 = LED (AC)
2 = 2 pole 2 = Bifurcated contacts 4 = Lockable test button +
3 = 3 pole 60.12/13 - 6 A only mechanical indicator
5* = Lockable test button + LED (AC)
Coil version 54* = Lockable test button + LED (AC) +
4 = Current sensing (60.12/13 only) mechanical indicator
8 = AC (50/60 Hz) 6* = LED + diode (DC, polarity positive
9 = DC to pin 2)
Coil voltage 7* = Lockable test button + LED + diode
See coil specifications (DC, polarity positive to pin 2)
74* = Lockable test button + LED + diode
(DC, polarity positive to pin 2) +
mechanical indicator
* Options not available for 220 V DC and
Selecting features and options: only combinations in the same row are possible. 400 V AC versions.
Preferred selections for best availability are shown in bold.
Type Coil version A B C D
60.12/13 AC 0-2 0 0-2-3-4-5 0
AC 0-2 0 54 /
AC 5 0- 2 0-2-3-4-5 0
AC 5 0- 2 54 /
DC 0-2 0 0-2-4-6-7 0
DC 0-2 0 74 /
DC 5 0- 2 0-2-4-6-7 0
DC 5 0- 2 74 /
current sensing 0 0 4 0
60.62/63 AC-DC 0-2-5 0 0 0

Descriptions: Options and Special versions

C: Option 3, 5, 54 C: Option 6, 7, 74
LED (AC) LED + diode (DC, polarity
positive to pin 2)

Lockable test button and mechanical flag indicator (0040, 0050, 0054, 0070, 0074)
1 The dual-purpose Finder test button can be used in two ways:
3
Case 1) The plastic pip (located directly above the test button) remains intact. In this case, when the
test button is pushed, the contacts operate. When the test button is released the contacts return to their
former state.
Case 2) The plastic pip is broken-off (using an appropriate cutting tool). In this case, (in addition to
the above function), when the test button is pushed and rotated, the contacts are latched in the
operating state, and remain so until the test button is rotated back to its former position.
In both cases ensure that the test button actuation is swift and decisive.
2

4
 60 Series - General purpose relays 6 - 10 A
Technical data
Insulation according to EN 61810-1 2 pole 3 pole
Nominal voltage of supply system V AC 230/400 230/400
Rated insulation voltage V AC 250 400 250 400
Pollution degree 3 2 3 2
Insulation between coil and contact set
Type of insulation Basic Basic
Overvoltage category III III
Rated impulse voltage kV (1.2/50 µs) 4 3.6
Dielectric strength V AC 2,000 2,000
Insulation between adjacent contacts
Type of insulation Basic Basic
Overvoltage category III III
Rated impulse voltage kV (1.2/50 µs) 4 3.6
Dielectric strength V AC 2,000 2,000
Insulation between open contacts
Type of disconnection Micro-disconnection Micro-disconnection
Dielectric strength V AC/kV (1.2/50 µs) 1,000/1.5 1,000/1.5
Conducted disturbance immunity
Burst (5...50)ns, 5 kHz, on A1 - A2 EN 61000-4-4 level 4 (4 kV)
Surge (1.2/50 µs) on A1 - A2 (differential mode) EN 61000-4-5 level 4 (4 kV)
Other data
Bounce time: NO/NC ms 2/4
Vibration resistance (5…55)Hz: NO/NC g 22/22
Shock resistance g 20
Power lost to the environment without contact current W 1.3 1.3
with rated current W 2.7 (60.12, 60.62) 3.4 (60.13, 60.63)

Contact specification
F 60 - Electrical life (AC) v contact current H 60 - Maximum DC1 breaking capacity

contacts in series
DC breaking current (A)
Cycles

Resistive load - cosϕ = 1

Inductive load - cosϕ = 0.4

DC voltage (V)

• When switching a resistive load (DC1) having voltage and current

values under the curve, an electrical life of ≥ 100·103 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with
the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.

Coil specifications AC coil data

Nominal Coil Operating range Resistance Rated coil
DC coil data voltage code consumption
Nominal Coil Operating range Resistance Rated coil UN Umin Umax R I at UN (50Hz)
voltage code consumption V V V Ω mA
UN Umin Umax R I at UN 6 8.006 4.8 6.6 4.6 367
V V V Ω mA 12 8.012 9.6 13.2 19 183
6 9.006 4.8 6.6 28 214 24 8.024 19.2 26.4 74 90
12 9.012 9.6 13.2 110 109 48 8.048 38.4 52.8 290 47
24 9.024 19.2 26.4 445 53.9 60 8.060 48 66 450 37
48 9.048 38.4 52.8 1,770 27.1 110 8.110 88 121 1,600 20
60 9.060 48 66 2,760 21.7 120 8.120 96 132 1,940 18.6
110 9.110 88 121 9,420 11.7 230 8.230 184 253 7,250 10.5
125 9.125 100 138 12,000 10.4 240 8.240 192 264 8,500 9.2
220 9.220 176 242 37,300 5.8 400 8.400 320 440 19,800 6
5
 60 Series - General purpose relays 6 - 10 A
Coil specifications
R 60 - DC coil operating range v ambient temperature R 60 - AC coil operating range v ambient temperature

1 - Max. permitted coil voltage. 1 - Max. permitted coil voltage.

2 - Min. pick-up voltage with coil at ambient temperature. 2 - Min. pick-up voltage with coil at ambient temperature.

Current sensing version

Current sensing DC coil data

L Coil code Imin (A) IN (A) Imax (A) R (Ω)

4202 1.7 2.0 2.4 0.15
4182 1.5 1.8 2.2 0.19
4162 1.4 1.6 1.9 0.24
4142 1.2 1.4 1.7 0.31
4122 1.0 1.2 1.4 0.42
4102 0.85 1.0 1.2 0.61
4092 0.8 0.9 1.1 0.75
4062 0.5 0.6 0.7 1.70
4032 0.25 0.3 0.4 6.70
4012 0.085 0.1 0.15 61
N
Current sensing AC coil data
Typical application with current sensing relays. Coil code Imin (A) IN (A) Imax (A) R (Ω)
An open circuit filiment of lamp L1 is detected by the current sensing
relay coil (K1) which causes the back-up safety lamp L2 to be energised, 4251 2.1 2.5 3.0 0.05
and indication of failure at the control panel via lamp S1. 4181 1.5 1.8 2.2 0.10
Example: navigation light. 4161 1.4 1.6 1.9 0.12
L1 = Light 4121 1.0 1.2 1.4 0.22
L2 = Safety light 4101 0.85 1.0 1.2 0.32
S1 = Control light
K1 = Relay 4051 0.42 0.5 0.6 1.28
4041 0.34 0.4 0.5 2.00
4031 0.25 0.3 0.4 3.57
4021 0.17 0.2 0.25 8.0
4011 0.085 0.1 0.15 32.1
Other types of current sensing relays are available on request.

Accessories
Sheet of marker tags for relay types 60.12 and 60.13, plastic, 72 tags, 6x12 mm 060.72

060.72

6
 90 Series - Socket overview for 60 series relays

Module Socket Relay Description Mounting Accessories

99.02 90.02 60.12 Screw terminal (Box clamp) socket Panel or 35 mm rail - Coil indication and EMC
90.03 60.13 Double A1 terminal (EN 60715) mount suppression modules
- Jumper link
- Timer modules
90.03 - Metal retaining clip
See page 8

Module Socket Relay Description Mounting Accessories

99.01 90.20 60.12 Screw terminal (Box clamp) socket Panel or 35 mm rail - Coil indication and EMC
90.21 60.13 (EN 60715) mount suppression modules
- Metal retaining clip

90.21
See page 9

Module Socket Relay Description Mounting Accessories

— 90.82.3 60.12 Screw terminal (Box clamp) socket Panel or 35 mm rail - Metal retaining clip
— 90.83.3 60.13 (EN 60715) mount

90.83.3
See page 10

Module Socket Relay Description Mounting Accessories

— 90.22 60.12 Screw terminal (Box clamp) socket Panel or 35 mm rail - Metal retaining clip
— 90.23 60.13 (EN 60715) mount

90.23
See page 10

Module Socket Relay Description Mounting Accessories

— 90.26 60.12 Screw terminal (Plate clamp) socket Panel or 35 mm rail - Metal retaining clip
— 90.27 60.13 (EN 60715) mount

90.26
See page 11

Module Socket Relay Description Mounting Accessories

— 90.12 60.12 Flange mount solder socket M3 screw fixing —
— 90.13 60.13
90.12
See page 11

Module Socket Relay Description Mounting Accessories

— 90.14 60.12 PCB socket PCB —
— 90.14.1 60.12
90.15 — 90.15 60.13
See page 12 — 90.15.1 60.13

7
 90 Series - Sockets and accessories for 60 series relays

Screw terminal (Box clamp) socket 90.02 90.02.0 90.03 90.03.0

panel or 35 mm rail (EN 60715) mount Blue Black Blue Black
For relay type 60.12 60.13
Accessories
Metal retaining clip 090.33
90.03
6-way jumper link 090.06
Approvals
Identification tag 090.00.2
(according to type):
Modules (see table below) 99.02
Timer modules (see table below) 86.00, 86.30
Technical data
Rated values 10 A - 250 V
Dielectric strength 2 kV AC
Certain relay/socket Protection category IP 20
combinations Ambient temperature °C –40...+70
Screw torque Nm 0.6
Wire strip length mm 10
Max. wire size for 90.02 and 90.03 sockets solid wire stranded wire
mm2 1x6 / 2x2.5 1x4 / 2x2.5
AWG 1x10 / 2x14 1x12 / 2x14

6-way jumper link for 90.02 and 90.03 sockets 090.06 (blue)
Rated values 10 A - 250 V
090.06
Approvals
(according to type):

86 series timer modules

86.00 Multi-voltage: (12…240)V AC/DC;
Multi-functions: AI, DI, SW, BE, CE, DE, EE, FE; (0.05 s…100 h) 86.00.0.240.0000
(12…24)V AC/DC; Bi-function: AI, DI; (0.05 s…100 h) 86.30.0.024.0000
(110...125)V AC; Bi-function: AI, DI; (0.05s…100h) 86.30.8.120.0000
(230...240)V AC; Bi-function: AI, DI; (0.05 s…100 h) 86.30.8.240.0000
Approvals (according to type):
86.30

99.02 coil indication and EMC suppression modules for 90.02 and 90.03 sockets
Diode (+A1, standard polarity) (6...220)V DC 99.02.3.000.00
LED (6...24)V DC/AC 99.02.0.024.59
LED (28...60)V DC/AC 99.02.0.060.59
LED (110...240)V DC/AC 99.02.0.230.59
99.02
LED + Diode (+A1, standard polarity) (6...24)V DC 99.02.9.024.99
Approvals LED + Diode (+A1, standard polarity) (28...60)V DC 99.02.9.060.99
(according to type):
LED + Diode (+A1, standard polarity) (110...220)V DC 99.02.9.220.99
LED + Varistor (6...24)V DC/AC 99.02.0.024.98
LED + Varistor (28...60)V DC/AC 99.02.0.060.98
LED + Varistor (110...240)V DC/AC 99.02.0.230.98
RC circuit (6...24)V DC/AC 99.02.0.024.09
DC Modules with RC circuit (28...60)V DC/AC 99.02.0.060.09
non-standard polarity RC circuit (110...240)V DC/AC 99.02.0.230.09
(+A2) on request. Residual current by-pass (110...240)V AC 99.02.8.230.07
8
 90 Series - Sockets and accessories for 60 series relays

Screw terminal (Box clamp) socket 90.20 90.20.0 90.21 90.21.0

panel or 35 mm rail (EN 60715) mount Blue Black Blue Black
For relay type 60.12 60.13
Accessories
Metal retaining clip (supplied with socket - packaging code SMA) 090.33
90.21
Modules (see table below) 99.01
Approvals Technical data
(according to type):
Rated values 10 A - 250 V
Dielectric strength 2 kV AC
Protection category IP 20
Ambient temperature °C –40…+70
Screw torque Nm 0.5
Wire strip length mm 10
Max. wire size for 90.20 and 90.21 sockets solid wire stranded wire
mm2 1x6 / 2x2.5 1x6 / 2x2.5
AWG 1x10 / 2x14 1x10 / 2x14

90.20 90.21

99.01 coil indication and EMC suppression modules for 90.20 and 90.21 sockets
Blue*
Diode (+A1, standard polarity) (6...220)V DC 99.01.3.000.00
Diode (+A2, non-standard polarity) (6...220)V DC 99.01.2.000.00
LED (6...24)V DC/AC 99.01.0.024.59
99.01
LED (28...60)V DC/AC 99.01.0.060.59
Approvals LED (110...240)V DC/AC 99.01.0.230.59
(according to type):
LED + Diode (+A1, standard polarity) (6...24)V DC 99.01.9.024.99
LED + Diode (+A1, standard polarity) (28...60)V DC 99.01.9.060.99
LED + Diode (+A1, standard polarity) (110...220)V DC 99.01.9.220.99
LED + Diode (+A2, non-standard polarity) (6...24)V DC 99.01.9.024.79
* Modules in Black LED + Diode (+A2, non-standard polarity) (28...60)V DC 99.01.9.060.79
housing are LED + Diode (+A2, non-standard polarity) (110...220)V DC 99.01.9.220.79
available on request.
LED + Varistor (6...24)V DC/AC 99.01.0.024.98
Green LED is standard. LED + Varistor (28...60)V DC/AC 99.01.0.060.98
Red LED available on LED + Varistor (110...240)V DC/AC 99.01.0.230.98
request. RC circuit (6...24)V DC/AC 99.01.0.024.09
RC circuit (28...60)V DC/AC 99.01.0.060.09
RC circuit (110...240)V DC/AC 99.01.0.230.09
Residual current by-pass (110...240)V AC 99.01.8.230.07

9
 90 Series - Sockets and accessories for 60 series relays

Screw terminal (Box clamp) socket 90.82.3 90.82.30 90.83.3 90.83.30

panel or 35 mm rail (EN 60715) mount Blue Black Blue Black
For relay type 60.12 60.13
Accessories
Metal retaining clip 090.33
90.83.3 Technical data
Approvals Rated values 10 A - 250 V
(according to type):
Dielectric strength 2 kV AC
Protection category IP 20
Ambient temperature °C –40…+70
Screw torque Nm 0.8
Max. wire size for 90.82.3 and 90.83.3 sockets solid wire stranded wire
mm2 1x6 / 2x4 1x6 / 2x4
AWG 1x10 / 2x14 1x10 / 2x14

90.82.3 90.83.3

Screw (Box clamp) terminal socket 90.22 90.23

panel or 35 mm rail (EN 60715) mount Blue Blue
For relay type 60.12 60.13
Accessories
Metal retaining clip (supplied with socket - packaging code SMA) 090.33
90.23
Technical data
Approvals Rated values 10 A - 250 V
(according to type): Dielectric strength 2 kV AC
Protection category IP 20
Ambient temperature °C –40…+70
Screw torque Nm 0.5
Wire strip length mm 7
Max wire size for 90.22 and 90.23 sockets solid wire stranded wire
mm2 1x6 / 2x2.5 1x6 / 2x2.5
AWG 1x10 / 2x14 1x10 / 2x14

90.22 90.23

10
 90 Series - Sockets and accessories for 60 series relays

Screw terminal (Plate clamp) socket 90.26 90.26.0 90.27 90.27.0

panel or 35 mm rail (EN 60715) mount Blue Black Blue Black
For relay type 60.12 60.13
Accessories
90.26 Metal retaining clip (supplied with socket - packaging code SMA) 090.33
Technical data
Approvals Rated values 10 A - 250 V
(according to type):
Dielectric strength 2 kV AC
Protection category IP 20
Ambient temperature °C –40…+70
Screw torque Nm 0.8
Wire strip length mm 10
Max. wire size for 90.26 and 90.27 sockets solid wire stranded wire
mm2 1x4 / 2x2.5 1x4 / 2x2.5
AWG 1x12 / 2x14 1x12 / 2x14

90.26 90.27

Flange mount solder socket mount with M3 screw 90.12 (black) 90.13 (black)
For relay type 60.12 60.13
Technical data
90.12 Rated values 10 A - 250 V
Approvals Dielectric strength 2 kV AC
(according to type): Ambient temperature °C –40…+70

11
 90 Series - Sockets and accessories for 60 series relays

PCB socket Blue 90.14 (Ø 20.5 mm) 90.15 (Ø 22 mm)

Blue 90.14.1 (Ø 17.5 mm) 90.15.1 (Ø 19 mm)
For relay type 60.12 60.13
90.15 Technical data
Approvals Rated values 10 A - 250 V
(according to type): Dielectric strength 2 kV AC
Ambient temperature °C –40…+70

90.14 90.15

Packaging code
How to code and identify retaining clip and packaging options for sockets.

Example:

9 0 . 2 1 S M A

A Standard packaging

SM Metal retaining clip

9 0 . 2 1 Without retaining clip

12