1-8 Demux
1-8 Demux
1-8 Demux
74F138
1-of-8 decoder/demultiplexer
Philips Semiconductors Product specification
A1 2 15 Q0
• Ideal for memory chip select decoding A2 3 14 Q1
• Industrial temperature range available (–40°C to +85°C) E0 4 13 Q2
E1 5 12 Q3
DESCRIPTION
E2 6 11 Q4
The 74F138 decoder accepts three binary weighted inputs (A0, A1,
A2) and when enabled, provides eight mutually exclusive, active low Q7 7 10 Q5
outputs (Q0 – Q7). The device features three enable inputs; two GND 8 9 Q6
active low (E0, E1) and one active high (E2). Every output will be
high unless E0 and E1 are low and E2 is high. This multiple enable
SF00174
function allows easy parallel expansion of the device to 1-of-32
(5 lines to 32 lines) decoder with just four 74F138s and one inverter
(see Figure 1). The device can be used as an eight output TYPICAL TYPICAL
demultiplexer by using one of the active low enable inputs as the TYPE PROPAGATION SUPPLY CURRENT
data input and the remaining enable inputs as strobes. Enable DELAY (TOTAL)
inputs not used must be permanently tied to their appropriate active
74F138 5.8ns 13mA
high or active low state.
ORDERING INFORMATION
ORDER CODE
DESCRIPTION COMMERCIAL RANGE INDUSTRIAL RANGE PKG DWG #
VCC = 5V ±10%, Tamb = 0°C to +70°C VCC = 5V ±10%, Tamb = –40°C to +85°C
16-pin plastic DIP N74F138N I74F138N SOT38-4
16-pin plastic SO N74F138D I74F138D SOT109-1
1 2 3
DMUX
1 15
0 0
2 14
0 1
G
A0 A1 A2 3
3 13
4 E0 2 2
5 E1 12
3
6 E2 11
Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 4
4 10
& 5
5 9
6
15 14 13 12 11 10 9 7 6 7
7
VCC = Pin 16
GND = Pin 8
SF00175 SF00176
LOGIC DIAGRAM
3
A2
2
A1
1
A0
4
E0
5
E1
6
E2
15 14 13 12 11 10 9 7
Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7
VCC = Pin 16
GND = Pin 8
SF00177
FUNCTION TABLE
INPUTS OUTPUTS
E0 E1 E2 A0 A1 A2 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7
H X X X X X H H H H H H H H
X H X X X X H H H H H H H H
X X L X X X H H H H H H H H
L L H L L L L H H H H H H H
L L H H L L H L H H H H H H
L L H L H L H H L H H H H H
L L H H H L H H H L H H H H
L L H L L H H H H H L H H H
L L H H L H H H H H H L H H
L L H L H H H H H H H H L H
L L H H H H H H H H H H H L
NOTES:
H = High voltage level
L = Low voltage level
X = Don’t care
APPLICATION
A0
A1
A2
A3
A4 74F04
H
E2 A0 A1 A2 E2 A0 A1 A2 E2 A0 A1 A2 E2 A0 A1 A2
E1 E1 E1 E1
E0
74F138 E0
74F138 E0
74F138 E0
74F138
Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7
Q0 Q31
SF00178
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
LIMITS
SYMBOL PARAMETER TEST CONDITIONS1 UNIT
MIN TYP2 MAX
AC ELECTRICAL CHARACTERISTICS
LIMITS
VCC = +5.0V VCC = +5.0V ± 10% VCC = +5.0V ± 10%
TEST Tamb = +25°C Tamb = 0°C to +70°C Tamb = –40°C to +85°C
SYMBOL PARAMETER UNIT
CONDITION CL = 50pF CL = 50pF CL = 50pF
RL = 500Ω RL = 500Ω RL = 500Ω
MIN TYP MAX MIN MAX MIN MAX
tPLH Propagation delay 3.5 5.6 7.0 3.5 8.0 3.0 8.5
Waveform 1, 2 ns
tPHL An to Qn 4.0 6.1 8.0 4.0 9.0 3.5 9.0
tPLH Propagation delay 3.5 6.4 7.0 3.5 8.0 3.0 8.0
Waveform 2 ns
tPHL E0 or E1 to Qn 3.0 5.3 7.0 3.0 7.5 3.0 7.5
tPLH Propagation delay 4.0 6.2 8.0 4.0 9.0 4.0 9.5
Waveform 1 ns
tPHL E2 to Qn 3.5 5.6 7.5 3.5 8.5 3.5 8.5
AC WAVEFORMS
For all waveforms, VM = 1.5V
An, E2
VM VM An, E0, E1 VM VM
VM VM VM VM
Qn Qn
SF00179 SF00180
Waveform 1. Propagation Delay for Inverting Outputs Waveform 2. Propagation Delay for Non-Inverting Outputs
SF00006
1991 Feb 14 6
Philips Semiconductors Product specification
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
1991 Feb 14 7
Philips Semiconductors Product specification
Objective Development This data sheet contains the design target or goal specifications for product development.
specification Specification may change in any manner without notice.
Preliminary Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date.
specification Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make
specification changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
yyyy mmm dd 8