Texas Stud Weld Accessories Catalog

FERRULE GRIPS
CLOSED FERRULE GRIP (1” LONG) BRASS

STUD SIZE FOOT SIZE GRIP DIA.(D) PART NO. PRICE
3/16 SMALL .305 GN‐019 7.00
1/4 SMALL .380 GN‐025 7.00
5/16 SMALL .445 GN‐031 7.00
3/8 SMALL .505 GN‐037 7.00
D
7/16 SMALL .585 GN‐043 7.00
1/2 SMALL .650 GN‐050 7.00
5/8 MEDIUM .785 GN‐062 9.00
3/4 MEDIUM 1.030 GN‐075 9.00
7/8 LARGE 1.203 GN‐087 13.00
1” LARGE 1.406 GN‐100 17.00
SPLIT FERRULE GRIP (1” LONG) BRASS

3/16 SMALL .305 GC‐019 9.00
1/4 SMALL .380 GC‐025 9.00
5/16 SMALL .445 GC‐031 9.00 D
3/8 SMALL .505 GC‐037 9.00
7/16 SMALL .585 GC‐043 9.00
1/2 SMALL .650 GC‐050 9.00
5/8 MEDIUM .785 GC‐062 13.00
3/4 MEDIUM 1.030 GC‐075 18.00
7/8 LARGE 1.203 GC‐087 24.00
1” LARGE 1.406 GC‐100 24.00
LONG SPLIT FERRULE GRIP (2” LONG) BRASS

1/4 SMALL .380 GD‐025 13.00
5/16 SMALL .445 GD‐031 13.00
3/8 SMALL .505 GD‐037 13.00 D
7/16 SMALL .585 GD‐043 13.00

1/2 SMALL .650 GD‐050 13.00
5/8 MEDIUM .785 GD‐062 16.00
3/4 MEDIUM 1.030 GD‐075 24.00

***ADD $1.00 FOR COPPER GRIPS***
2
CHUCKS
ADJUSTABLE CHUCKS
STUD DIA. PART NO. PRICE

2MM (.079) CN‐002M 39.00
#2 CN‐008 39.00
12 GA & #4 CN‐010 31.00
1/8 & #5 CN‐012 31.00
10 GA & #6 CN‐013 31.00
4MM (.155) CN‐004M 39.00 2-1/2”
#8 CN‐015 31.00
#10 & 5MM (.196) CN‐018 31.00
6MM (.236) CN‐006M 39.00
.215 CN‐021 39.00
.330 CN‐033 39.00
1/4 CN‐025 31.00
5/16 CN‐031 31.00
8MM CN‐008M 39.00 2-1/2”
3/8 CN‐037 31.00
10MM (.390) CN‐010M 39.00
7/16 CN‐043 31.00
12MM (.472) CN‐012M 39.00
1/2 CN‐050 31.00
14MM (.551) CN‐014M 50.00
9/16 CN‐056 50.00
5/8 CN‐062 47.00
16MM CN‐016M 56.00
.680 CN‐068 50.00
18MM (.708) CN‐018M 67.00 3”
3/4 CN‐075 62.00
7/8 CN‐087 62.00
20MM CN‐020M 72.00
1” CN‐100 72.00
*** ADD $16.00 FOR BERYLLIUM CHUCKS — ONLY AVAILABLE IN SIZES UP TO 1/2”
SPECIAL DIAMETER NON‐STANDARD 1/2” AND UNDER
3
LONG AND RECTANGULAR CHUCKS
3‐7/8” LONG ADJUSTABLE CHUCKS

STUD SIZE PART NO. PRICE
#6 CM‐013 42.00
#8 CM‐015 42.00
#10 & 5MM CM‐018 42.00
6 MM CM‐006M 49.00
1/4 CM‐025 42.00 3-7/8”
5/16 CM‐031 42.00
8MM CM‐008M 47.00
.330 CM‐033 53.00
3/8 CM‐037 48.00 SIZES CM‐025 AND UNDER ARE
10MM CM‐010M 53.00 BERYLLIUM
7/16 CM‐043 42.00
12MM CM‐012M 53.00
1/2 CM‐050 42.00
9/16 CM‐056 61.00
5/8 CM‐062 53.00
4‐3/4” EXTRA LONG ADJUSTABLE CHUCKS

#6 CL‐013 40.00 4-3/4”
#8 CL‐015 40.00
#10 CL‐018 40.00
1/4 CL‐025 40.00
5/16 CL‐031 40.00 SIZES CL‐025 AND UNDER ARE
3/8 CL‐037 40.00 BERYLLIUM
7/16 CL‐043 40.00
1/2 CL‐050 51.00
5/8 CL‐062 51.00
3/4 CL‐075 56.00
RECTANGULAR CHUCKS

1/8 X 1/4 CR‐CA 40.00
1/8 X 3/8 CR‐CB 40.00
1/8 X 5/8 CR‐CC 44.00
1/8 X 7/8 CR‐CH 94.00 3”
1/8 X 1” CR‐CE 94.00

1/4 X 3/4 CR‐CF 94.00
4
HEADED STUD CHUCKS
3/8 DIA. HEADED ANCHOR CHUCK (3/4” DIA. HEAD)

PART NO. DESCRIPTION PRICE
CH‐037 COMPLETE ASSY. 53.00
CH‐037‐1 SLEEVE ONLY 33.00
CH‐037‐2 BASE ONLY 31.00
CH‐037‐3 STOP SCREW 13.00
SCREWS 10‐32 X 3/8 1.00
1/2 DIA. HEADED ANCHOR CHUCK (1” DIA. HEAD)

3-1/2”
5/8 & 3/4 DIA. HEADED ANCHOR CHUCK (1‐1/4” DIA. HEAD)

7/8 DIA. HEADED ANCHOR CHUCK (1‐3/8” DIA. HEAD)

PART NO.DESCRIPTIONPRICE
CH‐087 COMPLETE ASSY. 58.00 3-1/4”

1” DIA. HEADED ANCHOR CHUCK (1‐5/8 DIA. HEAD)

SCREWS 10‐32 X 1/2 1.00
5
SPECIAL CHUCKS / LEGS
Y ANCHOR CHUCKS BENT STUD CHUCK
ANCHOR SIZE PART NO. PRICE

3/16 CY‐018 87.00
1/4 CY‐025 87.00 STUD DIA. BEND PART NO. PRICE
5/16 CY‐031 87.00 3/8 90 deg CB‐037‐90
3/8 45 deg CB‐037‐45
1/2 90 deg CB‐050‐90
ARC STUD WELDING LEGS 1/2 45 deg CB‐050‐45
5/8 90 deg CB‐062‐90
5/8 45 deg CB‐062‐45
3/4 90 deg CB‐075‐90
3/4 45 deg CB‐075‐45
L
MALE CHUCKS
LENGTH DIA. PART NO. PRICE
7” 5/16 L‐03107 24.00
9” 5/16 L‐03109 24.00
14” 5/16 L‐03114 24.00
18” 5/16 L‐03118 24.00 2-1/2”
7” 3/8 L‐03707 24.00
9” 3/8 L‐03709 24.00
14” 3/8 L‐03714 24.00 HOLE SIZE PART NO. PRICE
18” 3/8 L‐03718 33.00 8/32 CX‐008‐32 42.00
24” 3/8 L‐03724 40.00 10‐24 CX‐010‐24 42.00
27” 3/8 L‐03727 61.00 10‐32 CX‐010‐32 42.00
32” 3/8 L‐03732 89.00 1/4‐20 CX‐025‐20 42.00
36” 3/8 L‐03736 89.00 5/16‐18 CX‐031‐18 42.00
48” 3/8 L‐03748 111.00 3/8‐16 CX‐037‐16 42.00
5/16 LEG WASHER L‐031‐1 2.00 1/2‐13 CX‐050‐13 42.00
5/16 LEG SCREW L‐031‐2 2.00 5/8‐11 CX‐062‐11 42.00
3/8 LEG WASHER L‐037‐1 2.00 3/4‐10 CX‐075‐10 42.00
3/8 LEG SCREW L‐037‐2 2.00 1/4 CX‐025 42.00
3/8 CX‐037 42.00
6
WELD THRU DECK ACCESSORIES
WELD THRU DECK FOOT ASSEMBLY WELD THRU DECK FERRULE HOLDER

B‐0021 FOOT ASSY. 88.00
B‐0021‐1 FOOT ONLY 39.00
B‐0021‐2 EXTENSION BAR 61.00
B‐0060‐1 3/4 WTD/7/8 FLAT 72.00
B‐0021‐3 1/4‐20 X 1 SCREWS 2.00
B‐0060‐2 3/4 FLAT 72.00
B‐0060‐3 5/8 FLAT 72.00
B‐0060‐4 1” FLAT 72.00
B‐0060‐5 1/2 FLAT 72.00
REFACTORY FERRULE FOOT PLATE HEAVY DUTY FERRULE GRIP
DIA.
PART NO. STUD DIA. PRICE

GH‐050 1/2 33.00
PART NO. NECK DIA. PRICE GH‐062 5/8 33.00
QY‐025‐1 .810 67.00 GH‐075 3/4 38.00
QY‐025‐2 .930 67.00 GH‐087 7/8 38.00
QY‐025‐3 1.030 67.00 GH‐100 1 38.00
7
CLOSED FEET
B-1N B-2N B-3N
B-6N/B-7N B-4N/B-5N 028-833
STANDARD CLOSED FEET
GUN TYPE STUD SIZE PART NO. PRICE

PRO‐WELD INT. 1/8‐1/2 B‐1N 27.00
NELSON NS‐20 1/8‐1/2 B‐1N 27.00
NELSON NS‐30 1/8‐1/2 B‐6N 33.00
PRO‐WELD INT. 5/8‐3/4 B‐2N 29.00
NELSON NS‐20 5/8‐3/4 B‐2N 29.00
NELSON NS‐30 5/8‐3/4 B‐7N 29.00
PRO‐WELD INT. 7/8‐1” B‐3N 33.00
NELSON NS‐20 7/8‐1” B‐3N 33.00
BANTAM A‐58 1/8‐1/2 B‐4N 29.00
BANTAM A‐58 5/8‐3/4 B‐5N 29.00
PRO‐WELD INT. 1/8‐3/8 028‐833 29.00
8
SPLIT FEET
B-1C B-2C B-3C
B-6C/B-7C B-4C/B5C B-4CR/B-5CR
STANDARD SPLIT FEET
GUN TYPE STUD SIZE PART NO. PRICE

PRO‐WELD INT. 1/8‐1/2 B‐1C 29.00
NELSON NS‐20 1/8‐1/2 B‐1C 29.00
NELSON NS‐30 1/8‐1/2 B‐6C 33.00
PRO‐WELD INT. 5/8‐3/4 B‐2C 33.00
NELSON NS‐20 5/8‐3/4 B‐2C 33.00
NELSON NS‐30 5/8‐3/4 B‐7C 33.00
PRO‐WELD INT. 7/8‐1” B‐3C 37.00
NELSON NS‐20 7/8‐1” B‐3C 37.00
BANTAM A‐58 1/8‐1/2 B‐4C 37.00
BANTAM A‐58 5/8‐3/4 B‐5C 37.00
BANTAM C‐2 1/8‐1/2 B‐4CR (RECESSED) 37.00
BANTAM C‐2 5/8‐3/4 B‐5CR (RECESSED) 37.00
9
SPECIAL FEET AND FERRULE PLATES
SPLIT BI‐POD FEET

1/8‐1/2 BP‐1C 83.00
5/8‐3/4 BP‐2C 83.00
7/8‐1” BP‐3C 83.00
CLOSED BI‐POD FEET

1/8‐1/2 BP‐1N 83.00
5/8‐3/4 BP‐2N 83.00
7/8‐1” BP‐3N 83.00

**NOTE: PLEASE SPECIFY GUN TYPE**
TWIN LEG FERRULE FOOT PLATE

1/4 QN‐025 67.00
5/16 QN‐031 67.00
3/8 QN‐037 67.00
1/2 QN‐050 67.00
5/8 QN‐062 67.00
3/4 QN‐075 67.00
7/8 QN‐087 67.00
1” QN‐100 67.00

SINGLE LEG FERRULE FOOT PLATE

1/4 QM‐025 72.00
3/8 QM‐037 72.00
1/2 QM‐050 72.00
5/8 QM‐062 72.00
3/4 QM‐075 72.00
10
SPECIAL ACCESSORIES
FERRULE TUBING

STUD SIZE PART NO. I.D. O.D. L PRICE
#8 MP‐015 .291 .360 36” 80.00 O.D. L
#10 MP‐018 .305 .375 36” 80.00
1/4 MP‐025 .380 .500 36” 80.00
5/16 MP‐031 .445 .562 36” 80.00
I.D.
3/8 MP‐037 .505 .625 36” 80.00
7/16 MP‐043 .585 .687 36” 80.00
1/2 MP‐050 .650 .750 36” 80.00
5/8 MP‐062 .785 .906 36” 80.00
3/4 MP‐075 1.030 1.156 36” 80.00
FERRULE TUBE BUSHING

STUD SIZE PART NO. I.D. O.D. PRICE
#8 MB‐015 .360 .875 11.00 1/2”
#10 MB‐018 .375 .875 11.00 O.D.
1/4 MB‐025 .500 .875 11.00

5/16 MB‐031 .562 .875 11.00
3/8 MB‐037 .625 .875 11.00
I.D.
7/16 MB‐043 .687 .875 11.00
1/2 MB‐050 .750 .875 11.00
5/8 MB‐062 .906 1.156 16.00
GAS ADAPTOR FEET FOR ALUMINUM WELDING (SPECIFY GUN TYPE WHEN ORDERING)
PART NO. BG‐1 PART NO. BG‐2 PART NO. BG‐3

PRICE: 400.00 PRICE: 200.00 PRICE: 300.00
USE WITH FERRULE USE WITHOUT FERRULE
NELSON #751‐929‐999 NELSON P/N #751‐022‐000
FOOT ONLY BG‐2‐1 73.00 FOOT ONLY BG‐3‐1 111.00
SPARK SHIELD ONLY BG‐2‐2 49.00 SPARK SHIELD ONLY BG‐3‐2 111.00
VALVE ASSY. BG‐2‐3 155.00 HOSE CONNECTOR 119‐0010 56.00
11
CAPACITOR DISCHARGE ACCESSORIES
“B” COLLETS

STUD DIA PART NO. PRICE
3 MM CDB‐003M 14.00
14 GA CDB‐008 14.00
12 GA & #4 CDB‐010 14.00
1/8 GA & #5 CDB‐012 14.00
10 GA & #6 CDB‐013 14.00
3/8 DIA
4 MM CDB‐004M 14.00 1-3/8
#8 CDB‐015 14.00
#10 CDB‐018 14.00
5 MM CDB‐005M 14.00
6 MM CDB‐006M 14.00
.215 CDB‐021 14.00
1/4 CDB‐025 14.00
5/16 CDB‐031 31.00
“B” COLLETS AGM STYLE

14 GA CDB‐008A 14.00
12 GA CDB‐010A 14.00
#6 CDB‐013A 14.00
#8 CDB‐015A 14.00 3/8 DIA.
#10 CDB‐018A 14.00 1-3/16

1/4 CDB‐025A 14.00
SOYER COLLETS

#6 CDBS‐013 23.00 .390
4 MM CDBS‐004M 23.00
#8 CDBS‐015 23.00
#10 CDBS‐018 23.00
1.781
5 MM CDBS‐005M 23.00
6 MM CDBS‐006M 23.00
1/4 CDBS‐025 23.00
12
ONE PIECE CONTACT/MAGNETIC CHUCK

PART NO. PRICE
039‐613 36.00
MAGNETIC CHUCK

035‐301 COMPLETE ASSY 49.00
017‐633 MAGNET ONLY 40.00
029‐615 CONDUCTOR PLATE 20.00
039‐609 INSUL. TUBE 9.00
039‐610 INSUL. DISC 9.00
SCREW 10‐32 X 7/8 9.00
“B” COLLETS PROTECTOR

14 GA X 12 GA 028‐837 23.00
10 GA 028‐838 23.00
BODY ONLY 028‐836 20.00
12 GA INSERT 028‐834 4.00
10 GA INSERT 028‐835
“B” STOP

STUD STOP PART NO. PRICE
1/4 1‐1/4 033‐781 3.50
3/8 1‐1/8 033‐782 3.50
1/2 1” 033‐783 3.50
5/8 7/8 033‐784 3.50 SHORT BUTTON STOP
3/4 3/4 033‐785 3.50
7/8 5/8 033‐775 3.50
1” 1/2 033‐776 3.50
1‐1/8 3/8 033‐777 3.50
1‐1/4 1/4 033‐778 3.50
1‐3/8 (BUTTON STOP) 1/8 033‐779 3.50
UNIVERSAL 033‐780 3.50
UNIVERSAL “B” STOP
13
COLLETS INSERTS FOR WELD STUDS COLLETS INSERTS FOR WELD PINS
1/4 DIA
1-3/4”
STUD DIA.
STUD DIA. X DEPTH PART NO. PRICE
X DEPTH PART NO. PRICE 12GA X 1/2 CIP‐010‐050 18.00
#4 X 1/4 CI‐010‐025 18.00 12GA X 3/4 CIP‐010‐075 18.00
#4 X 3/8 CI‐010‐037 18.00 12GA X 1” CIP‐010‐100 18.00
#4 X 1/2 CI‐010‐050 18.00 10GA X 1/2 CIP‐014‐050 18.00
#4 X 1” CI‐010‐100 18.00 10GA X 3/4 CIP‐014‐075 18.00
#6X 1/4 CI‐013‐025 18.00
#6 X 3/8 CI‐013‐037 18.00 STANDARD SPARK SHIELD
#6 X 1/2 CI‐013‐050 18.00
#6 X 5/8 CI‐013‐062 18.00
#6 X 3/4 CI‐013‐075 18.00
#6X 1” CI‐013‐100 18.00
10GA X 1/2 CI‐014‐050 18.00
10GA X 3/4 CI‐014‐075 18.00
STUD RANGE PART NO. PRICE
10GA X 1 CI‐014‐100 18.00
14 GA – #6 033‐764 18.00
#8X 1/4 CI‐015‐025 18.00
#8 X 3/8 CI‐015‐037 18.00
#8 X 1/2 CI‐015‐050 18.00 VENTED SPARK SHIELD
#8 X 5/8 CI‐015‐062 18.00
#8 X 3/4 CI‐015‐075 18.00
#8X 1” CI‐015‐100 18.00
#10 X 1/4 CI‐018‐025 18.00
#10 X 3/8 CI‐018‐037 18.00
#10 X 1/2 CI‐018‐050 18.00 STUD RANGE PART NO. PRICE
#10 X 5/8 CI‐018‐062 18.00 14 GA – 10 GA 033‐769 20.00
#10 X 3/4 CI‐018‐075 18.00
#10X 1” CI‐018‐100 18.00
1/4 X 1/4 CI‐025‐025 18.00 TEMPLATE TUBE ADAPTOR
1/4 X 3/8 CI‐025‐037 18.00
1/4 X 1/2 CI‐025‐050 18.00
1/4 X 5/8 CI‐025‐062 18.00
1/4 X 3/4 CI‐025‐075 18.00
1/4 X 1” CI‐025‐100 18.00
5/16 X 3/8 CI‐031‐037 25.00
5/16 X 1/2 CI‐031‐050 25.00
5/16 X 5/8 CI‐031‐062 25.00
5/16 X 3/4 CI‐031‐075 25.00 TEMPLATE I.D. PART NO. PRICE
5/16 X 1” CI‐031‐100 25.00 1” DIA. 039‐839 333.00
3/8 X 1/2 CI‐037‐050 25.00 1‐1/4” DIA. 039‐840 333.00
3/8 X 3/4 CI‐037‐075 25.00
3/8 X 1” CI‐037‐100 25.00 14
NELSON & KSM COLLETS
NELSON STYLE COLLETS
3/8”DIA.
2-3/8”
STUD SIZE PART NO. NELSON # PRICE

#6 CDBN‐013 500‐001‐356 17.00
#8 CDBN‐015 500‐001‐357 17.00
#10 CDBN‐018 500‐001‐366 17.00
1/4 CDBN‐025 500‐001‐359 17.00
5/16 CDBN‐031 500‐001‐360 22.00
4 MM CDBN‐004M 500‐001‐361 22.00
6 MM CDBN‐006M 500‐001‐362 22.00
12 GA CDBN‐010 500‐001‐363 22.00
NELSON ADJ. STOPS FOR ABOVE
STUD LENGTH PART NO. PRICE

1/4 TO 5/8 500‐017‐017 16.00
3/4 TO 1‐1/8 500‐017‐018 16.00
1‐1/4 TO 1‐5/8 500‐017‐019 16.00
1‐3/4 TO 2‐1/8 500‐017‐020 16.00
KSM / ERICO AIR COLLET
7/16
1-1/2”
BOTTOM LOAD RAM FEED

STUD DIA PART NO. PRICE STUD DIA PART NO. PRICE
#4 (.112) 016‐412 #4 (.112) 025‐016
#6 (.138) 016‐415 #6 (.138) 025‐017
#8 (.164) 016‐416 #8 (.164) 025‐018
#10 (.189) 004‐684 #10 (.189) 025‐019
NON‐STOCK ITEM / ALLOW 2 WEEKS FOR DELIVERY
15
ADAPTORS
B‐CI ADAPTOR K‐B ADAPTORS
1/4-20
3/8 DIA
1/4 DIA 3/8 DIA

L 1-3/4
PARTNO. PRICE
PART NO. PRICE
044‐082 7/8 LONG 17.00
039‐464 45.00
033‐746 1‐9/16 LONG 13.00
B‐N ADAPTOR K‐N ADAPTORS
1/4-20
ARC
ARC
TAPER
TAPER
1-7/8 2-3/8
PART NO. PRICE
039‐468 39.00 PART NO. PRICE
033‐750 47.00
ADAPTORS
MISCELLANEOUS ADAPTORS
ARC

TAPER
I.D.
MT‐0008 TEMPLATE TUBE 96.00
1/4‐1/2 ARC STUDS
L

MT‐0012 TEMPLATE TUBE 107.00
PART NO .I.D. PRICE 5/8‐3/4 ARC STUDS
044‐083 N‐B 3/8 ID 28.00
044‐084 N‐C 1/4 ID 28.00 033‐505L L‐TEC CHUCK 56.00
ADAPTOR
THREADED TAPERED ADAPTORS
033‐749 K‐CI ADAPTORS
751‐458‐049 NS‐30 CHUCK ADAPTORS

PART NO. PRICE
MT‐0003 22.00 033‐505 Chuck Adaptor
033‐506 Connector Stud
16
WELD CABLE CONNECTORS
HEAVY DUTY HI TEMP CONNECTOR
PART NO. DESCRIPTION PRICE PART NO. DESCRIPTION PRICE

107‐0006 4/O (M) HI TEMP 60.00 107‐0007 4/O (F) HI TEMP 60.00
107‐0006‐1 4/O (M) SLEEVE 17.00 107‐0007‐1 4/O (F) SLEEVE 17.00
107‐0006‐2 4/O BRASS ONLY 42.00 107‐0007‐2 4/O BRASS ONLY 42.00
107‐0007‐MF HI TEMP PIN 1.90 (FITS (M) OR (F) )

COPPER WRAP .50
LIGHT DUTY CONNECTOR

107‐0010 1/O (M) FIBER SHELL 38.00
107‐0011 1/O (F) FIBER SHELL 38.00
107‐0012 #4 (M) FIBER SHELL 38.00
17
CONTROL CABLE CONNECTORS
CONTROL CABLE CONNECTOR

107‐0014 MALE 4 POLE CONNECTOR 99.00
107‐0015 FEMALE 4 POLE CONNECTOR 99.00
107‐0001 PANEL MOUNT CONNECTOR 99.00
HUBBELL STYLE CONNECTOR
NELSON 2‐WIRE (M) PANEL MOUNT PROWELD HUBBELL (M)

107‐0016 NELSON 2‐WIRE (M) 49.00
107‐0017 NELSON 2‐WIRE (F) 52.00
107‐0018 NELSON 2‐WIRE (PANEL MOUNT) 54.00
107‐0019 (M) RUBBER COVER 34.00
107‐0020 (F) RUBBER COVER 18.00
107‐0030 PROWELD HUBBELL (M) 29.00
107‐0032 PROWELD HUBBELL (F) 41.00
107‐0031 PROWELD HUBBELL (PANEL MOUNT) 41.00
18
PANEL MOUNT CAMLOK CONNECTORS

107‐0003 MALE PANEL MOUNT 80.00
107‐0002 FEMALE PANEL MOUNT 40.00
WELD CABLE LUGS

123‐0003 #4 W/#10 HOLE 4.00
123‐0001 #1 W/#10 HOLE 4.00
123‐0006 #1 W/1/4 HOLE 4.00
123‐0002 #1 W/3/8 HOLE 4.00
123‐0008 1/O W/3/8 HOLE 7.00
123‐0009 1/O W/1/2/ HOLE 7.00
123‐0013 4/O W/3/8 HOLE 9.00
123‐0010 4/O W/1/2/ HOLE 9.00
ACCESSORIES

102‐0041 ALLEN WRENCH SET 18.00
102‐0042 CHUCK EJECTOR KEY 15.00
19
TRU-WELD Stud Welding

Concrete Anchor ‐ Shipping Weight Chart
Stud Stud Lbs. Pieces Pounds Per Pieces Per Pounds Per
Diameter Length Per 1000 Per Box Box Pallet Pallet
1‐1/8 22 2,000 48 54,000 1,296
2‐11/16 43 1,000 45 27,000 1,215
1/4 3‐1/8 50 1,000 51 27,000 1,377
4‐1/8 63 600 38 16,200 1,026
1‐1/4 65 1,000 67 27,000 1,809
1‐3/8 68 1,000 70 27,000 1,890
1‐5/8 77 1,000 79 27,000 2,133
2‐1/8 92 700 67 18,900 1,809
2‐5/8 111 600 66 16,200 1,782
3/8 3‐1/8 124 500 62 13,500 1,674
4‐1/8 154 350 55 9,450 1,485
5‐1/8 185 300 56 8,100 1,512
6‐1/8 212 200 44 5,400 1,188
8‐1/8 274 250 69 2,250 1,863
1‐1/8 112 600 68 16,200 1,836
1‐3/8 125 500 65 13,500 1,755
1‐1/2 132 500 68 13,500 1,836
1‐5/8 138 450 64 12,150 1,728
2‐1/8 166 400 70 10,800 1,890
2‐5/8 198 350 71 9,450 1,917
3‐1/8 223 300 69 8,100 1,863
1/2 3‐5/8 246 200 51 5,400 1,377
4‐1/8 277 200 56 5,400 1,512
4‐3/8 290 200 58 5,400 1,566
5‐1/8 326 150 45 4,050 1,215
5‐5/16 339 150 53 4,050 1,431
6‐1/8 388 125 50 3,375 1,350
8‐1/8 495 100 50 2,700 1,350
1‐7/16 208 400 85 10,800 2,295
1‐11/16 227 325 77 8,775 2,079
1‐15/16 248 300 78 8,100 2,106
2‐1/8 264 250 68 6,750 1,836
2‐3/16 270 250 71 6,750 1,917
2‐11/16 319 250 81 6,750 2,187
3‐3/16 363 200 75 5,400 2,025
5/8 3‐11/16
4‐3/16
398
444
150
150
62
69
4,050
4,050
1,674
1,863
4‐11/16 487 125 63 3,375 1,701
5‐3/16 528 100 55 2,700 1,485
6‐3/16 604 90 55 2,430 1,485
6‐9/16 646 80 52 2,160 1,404
8‐3/16 781 50 40 1,350 1,080
10‐3/16 946 100 98 900 882

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com
460 Lake Road (330) 725‐0161 Fax http://www.truweldstudwelding.com
Medina, Ohio 44256 [email protected] http://www.weldstud.com


Shear Connector ‐ Shipping Weight Chart
Stud Stud Pounds Per Pieces Pounds Pieces Pounds
Diameter Length 1000 Pieces Per Box Per Box Per Pallet Per Pallet
2‐3/16 352 200 71 9,600 3,408
2‐11/16 414 150 62 7,200 2,976
3‐3/16 478 125 60 6,000 2,880
3‐11/16 548 100 55 4,800 2,640
4‐3/16 600 100 62 4,800 2,976
4‐11/16 672 75 51 3,600 2,448
5‐3/16 735 60 44 2,880 2,112
3/4 5‐11/16 797 60 48 2,880 2,304
6‐3/16 852 60 50 2,880 2,400
6‐11/16 905 70 64 1,890 1,728
7‐3/16 968 60 59 1,620 1,593
8‐3/16 1,105 50 56 1,350 1,512
9‐3/16 1,222 100 126 900 1,134
10‐3/16 1,339 100 137 900 1,233
3‐3/16 631 100 66 2,700 1,782
3‐11/16 709 100 74 2,700 1,998
4‐3/16 796 100 82 2,700 2,214
4‐11/16 878 80 72 2,160 1,944
5‐3/16 961 75 75 2,025 2,025
5‐11/16 1,067 60 65 1,620 1,755
7/8 6‐3/16 1,137 50 57 1,350 1,539
6‐11/16 1,236 50 63 1,350 1,701
7‐3/16 1,306 45 59 1,215 1,593
8‐3/16 1,496 40 59 1,080 1,593
9‐3/16 1,666 75 125 675 1,125
10‐3/16 1,836 75 139 675 1,251
3‐1/4 894 75 70 2,025 1,890
4‐1/4 1,079 50 57 1,350 1,539
5‐1/4 1,302 50 67 1,350 1,809
1 6‐1/4 1,514 40 63 1,080 1,701
7‐1/4 1,737 85 154 765 1,350
8‐1/4 1,978 85 171 765 1,539
9‐1/4 2,193 50 111 360 819
3‐3/8 500 125 62 6,000 2,976
3‐7/8 567 100 58 4,800 2,784
4‐3/8 625 100 62 4,800 2,976
3/4 4‐7/8 683 75 51 3,600 2,448
Thru‐Deck 5‐3/8 754 60 45 2,880 2,160
5‐7/8 810 60 49 2,880 2,352
6‐3/8 925 60 56 2,880 2,688

Estimated Weights for Threaded Studs In Pounds Per 1000 Pieces
Length 1/4” 5/16” 3/8” 7/16” 1/2” 5/8” 3/4” 7/8”

3/4 8.3 12.8 18.8 25.5 34.5
1 11.0 17.0 25.0 34.0 46.0 70.0
1‐1/4 13.8 21.3 31.3 42.5 57.5 87.5 133.8
1‐1/2 16.5 25.5 37.5 51.0 69.0 105.0 160.5 243.8
1‐3/4 19.3 29.8 43.8 59.5 80.5 122.5 187.3 284.4
2 22.0 34.0 50.0 68.0 92.0 140.0 214.0 325.0
2‐1/4 24.8 38.3 56.3 76.5 103.5 157.5 240.8 365.6
2‐1/2 27.5 42.5 62.5 85.0 115.0 175.0 267.5 406.3
2‐3/4 30.3 46.8 68.8 93.5 126.5 192.5 294.3 446.9
3 33.0 51.0 75.0 102.0 138.0 210.0 321.0 487.5
3‐1/4 35.8 55.3 81.3 110.5 149.5 227.5 347.8 528.1
3‐1/2 38.5 59.5 87.5 119.0 161.0 245.0 374.5 568.8
3‐3/4 41.3 63.8 93.8 127.5 172.5 262.5 401.3 609.4
4 44.0 68.0 100.0 136.0 184.0 280.0 428.0 650.0
4‐1/4 46.8 72.3 106.3 144.5 195.5 297.5 454.8 690.6
4‐1/2 49.5 76.5 112.5 153.0 207.0 315.0 481.5 731.3
4‐3/4 52.3 80.8 118.8 161.5 218.5 332.5 508.3 771.9
5 55.0 85.0 125.0 170.0 230.0 350.0 535.0 812.5
Estimated Weights of No Thread Studs in Pounds Per 1000 Pieces
Length 3/16” 1/4” 5/16” 3/8” 7/16” 1/2” 5/8” 3/4” 7/8”
3/4 6.0 10.5 16.4 23.5 31.9 41.7
1 8.0 14.0 21.8 31.3 42.5 55.6 86.6
1‐1/4 10.0 17.5 27.3 39.1 53.1 69.5 108.3 156.0
1‐1/2 12.0 21.0 32.7 47.0 63.8 83.4 129.9 187.2 254.0
1‐3/4 14.0 24.5 38.2 54.8 74.4 97.3 151.6 218.4 297.5
2 16.0 28.0 43.6 62.6 85.0 111.2 173.2 249.6 340.0
2‐1/4 18.0 31.5 49.1 70.4 95.6 125.1 194.9 280.8 382.5
2‐1/2 20.0 35.0 54.5 78.3 106.3 139.0 216.5 312.0 425.0
2‐3/4 22.0 38.5 60.0 86.1 116.9 152.9 238.2 343.2 467.5
3 24.0 42.0 65.4 93.9 127.5 166.8 259.8 374.4 510.0
3‐1/4 26.0 45.5 70.9 101.7 138.1 180.7 281.5 405.6 552.5
3‐1/2 28.0 49.0 76.3 117.4 148.8 194.7 303.1 436.8 595.0
3‐3/4 30.0 52.5 81.8 125.2 159.4 208.5 324.8 468.0 637.5
4 32.0 56.0 87.2 128.6 170.0 222.4 346.4 499.2 680.0
4‐1/4 34.0 59.5 92.7 133.0 180.6 236.3 368.1 530.4 722.5
4‐1/2 36.0 63.0 98.1 140.9 191.3 250.2 389.7 561.6 765.0
4‐3/4 38.0 66.5 103.6 148.7 201.9 264.1 411.4 592.8 807.5
5 40.0 70.0 109.0 156.5 212.5 278.0 433.0 624.0 850.0

STANDARD FERRULES
SUPPLIED WITH TRU‐WELD STUDS
F1 C FHD TD
(Standard Duty) (Collar Stud) (Heavy Duty) (Thru Deck)
R A2
P
(Reduced Base) (Angle Ferrule)
(Pitch Diameter Stud)
1) THE “F” FERRULE IS ALSO AVAILABLE IN THE LOW
THE TRU‐WELD FERRULE (ARC SHIELD) IS PROFILE VERSIONS.

SPECIALLY DESIGNED TO WITHSTAND
2) THE “A” FERRULE PICTURED ABOVE IS THE
HEAT SHOCK AS WELL AS REASONABLY COMBINATION INSIDE‐OUTSIDE ANGLE FERRULE.
HIGH TEMPERATURES WITHOUT MELTING THE INSIDE‐ONLY AND OUTSIDE‐ONLY FERRULES
OR BREAKING. THE TRU‐WELD FERRULE ARE ALSO STANDARD STOCK ITEMS.
COMPLIMENTS THE UNIFORM FLUX LOAD

TO AFFECT A TOP QUALITY WELD. INSIDE ANGLE

SPECIAL FERRULES ARE ALSO AVAILABLE
UPON REQUEST.

OUTSIDE ANGLE

STANDARD FERRULES
NOMINAL TRU-WELD
TYPE D H G E
SIZE PART NUMBER
3/16 FER03-F .390 .390 or .250 .281 .156
1/4 FER04-F .455 .390 or .250 .380 .156
5/16 FER05-F .578 .390 .445 .156
3/8 FER06-F .640 .390 .505 .156
7/16 FER07-F .703 .422 .585 .188
F 1/2 FER08-F .795 .438 .650 .188
5/8 FER10-F 1.030 .516 .785 .188
3/4 FER12-F 1.218 .656 1.030 .188
7/8 FER14-F 1.406 .732 1.210 .188
1 FER16-F 1.610 .820 1.406 .188
1/4 FER04-FHD .645 .390 .515 .150
3/8 FER06-FHD .800 .400 .645 .150
FHD 1/2 FER08-FHD .875 .455 .785 .185
5/8 FER10-FHD 1.230 .520 1.035 .185
1/4 FER04-C .875 .250 .785 .125
5/16 FER05-C .875 .250 .785 .125
C 3/8 FER06-C .875 .250 .785 .125
1/2 FER08-C 1.203 .281 1.045 .156
1/4 FER04-P .455 .250 .380 .125
5/16 FER05-P .535 .250 .445 .125
3/8 FER06-P .595 .265 .505 .125
7/16 FER07-P .675 .329 .585 .156
P 1/2 FER08-P .740 .362 .650 .156
5/8 FER10-P .905 .433 .785 .156
3/4 FER12-P 1.150 .526 1.030 .187
7/8 FER14-P 1.330 .593 1.203 .187
1 FER16-P 1.526 .661 1.406 .187
3/8 FER06-R .595 .250 .505 .125
7/16 FER07-R .675 .250 .585 .125
R 1/2 FER08-R .740 .281 .650 .156
5/8 FER10-R .875 .281 .785 .156
3/4 FER12-R 1.030 .375 .921 .187
1/2 FER08-TD .800 .450 .645 .185
5/8 FER10-TD 1.015 .525 .775 .185
TD 3/4 FER12-TD 1.335 .600 1.210 .185
7/8 FER14-TD 1.528 .666 1.406 .200
1/4 FER04-A .455 .500 .380 .156
3/8 FER06-A .640 .480 .505 .156
A 1/2 FER08-A .795 .688 .650 .188
5/8 FER10-A 1.030 .875 .785 .188
3/4 FER12-A 1.218 .875 1.030 .188

HEADED CONCRETE ANCHOR – FULL WELD BASE

TYPE CA STUD
TYPE F FERRULE SUPPLIED

Head Diameter (HD) – 1/2” for all 1/4” Headed Concrete Anchors.
Head Height (HT) – 3/16” for all 1/4” Headed Concrete Anchors.

WELD STUD SPECIFICATIONS WELD STUD PACKAGING WELD STUD WEIGHTS

D L TRU‐WELD Pieces Boxes Pieces
Box Pallet
1,000
Diameter Length Per Per Per Piece
Part Number Weight Weight
Box Pallet Pallet Weight
1/4 1-1/8 CA04‐018‐11 2,000 27 54,000 48 lbs. 1,296 lbs. 22 lbs.

1/4 2-11/16 CA04‐043‐11 1,000 27 27,000 45 lbs. 1,215 lbs. 43 lbs.
1/4 3-1/8 CA04‐050‐11 1,000 27 27,000 51 lbs. 1,377 lbs. 50 lbs.
1/4 4-1/8 CA04‐066‐11 600 27 16,200 38 lbs. 1,026 lbs. 63 lbs.

Concrete Anchors are used in all types of concrete Mechanical Property Requirements
connections. They can be welded to a flat surface, or to the
inside or outside of an angle.
Type A Type B
Length: Length is listed before weld. Stud diameters 1/4” will
be approx. 1/8” shorter after welding. 61,000 psi 65,000 psi
Tensile Strength
TRU‐WELD concrete anchors can be made in any length above min. min.
the standard minimum. 49,000 psi 51,000 psi
Material: Low carbon steel, ASTM A29, 1010‐1020. CA Studs Yield Strength
min. min.
are also available in weldable stainless steel. Type 302 is the
most commonly used. Other grades of stainless steel (except Elongation (% in 2 in.) 17% min. 20% min.

Type 303) are available when required.
Elongation (% in 5x dia.) 14% min. 15% min.

Reduction of Area 50% min. 50% min.
CHUCK FOOT GRIP FERRULE FOOT PLAT
PART # PART # PART # (DUAL LEG)
GC‐025 (Standard QN‐025 (Standard Type A Studs are general purpose studs.
B‐1C
Duty) Duty)
CN‐050 Type B Studs are headed, bent, or of other configuration that
GC‐037 QN‐037 are used as an essential component in composite beam design
B‐1C
(Heavy Duty) (Heavy Duty) and construction.



TYPE CA STUD

Diameter (HD) – 3/4” for all 3/8” Headed Concrete Anchors.


Box Pallet
1,000
3/8 1-3/8 CA06‐022‐11 1,000 27 27,000 70 lbs. 1,890 lbs. 68 lbs.

3/8 1-5/8 CA06‐026‐11 1,000 27 27,000 79 lbs. 2,133 lbs. 77 lbs.
3/8 2-1/8 CA06‐034‐11 700 27 18,900 67 lbs. 1,809 lbs. 92 lbs.
3/8 2-5/8 CA06‐042‐11 600 27 16,200 66 lbs. 1,782 lbs. 111 lbs.
3/8 3-1/8 CA06‐050‐11 500 27 13,500 62 lbs. 1,674 lbs. 124 lbs.

3/8 4-1/8 CA06‐066‐11 350 27 9,450 55 lbs. 1,485 lbs. 154 lbs.

3/8 5-1/8 CA06‐082‐11 300 27 8,100 56 lbs. 1,512 lbs. 185 lbs.
3/8 6-1/8 CA06‐098‐11 200 27 5,400 44 lbs. 1,188 lbs. 212 lbs.
3/8 8-1/8 CA06‐130‐11 250 9 2,250 69 lbs. 1,863 lbs. 274 lbs.

Concrete Anchors are used in all types of concrete
Mechanical Property Requirements

inside or outside of an angle. Type A Type B
be approx. 1/8” shorter after welding. TRU‐WELD concrete 61,000 psi 65,000 psi
Tensile Strength
min. min.
anchors can be made in any length above the standard 49,000 psi 51,000 psi
minimum. Yield Strength
min. min.
Material: Low carbon steel, ASTM A29, 1010‐1020. CA Studs Elongation (% in 2 in.) 17% min. 20% min.
most commonly used. Elongation (% in 5x dia.) 14% min. 15% min.
CHUCK FOOT GRIP FERRULE FOOT PLATE Reduction of Area 50% min. 50% min.


GC‐037 (Standard QN‐037 Type A Studs are general purpose studs.
B‐1C
Duty) (Standard Duty)
CH‐037 Type B Studs are headed, bent, or of other configuration that
GC‐050 QN‐050
B‐1C are used as an essential component in composite beam design
(Heavy Duty) (Heavy Duty)
and construction.



TYPE CA STUD

Head Diameter (HD) – 1” for all 1/2” Headed Concrete Anchors.


Box Pallet
1,000
1/2 1-1/8 CA08‐018‐11 600 27 16,200 68 lbs. 1,836 lbs. 112 lbs.

1/2 1-1/2 CA08‐024‐11 500 27 13,500 68 lbs. 1,836 lbs. 132 lbs.
1/2 1-5/8 CA08‐026‐11 450 27 12,150 64 lbs. 1,728 lbs. 138 lbs.
1/2 2-1/8 CA08‐034‐11 400 27 10,800 67 lbs. 1,809 lbs. 166 lbs.
1/2 2-5/8 CA08‐042‐11 350 27 9,450 71 lbs. 1,917 lbs. 198 lbs.

1/2 3-1/8 CA08‐050‐11 300 27 8,100 68 lbs. 1,836 lbs. 223 lbs.

1/2 4-1/8 CA08‐066‐11 200 27 5,400 56 lbs. 1,512 lbs. 277 lbs.
1/2 5-5/16 CA08‐085‐11 150 27 4,050 52 lbs. 1,404 lbs. 339 lbs.
1/2 6-1/8 CA08‐098‐11 125 27 3,375 49 lbs. 1,323 lbs. 388 lbs.

1/2 8-1/8 CA08‐130‐11 100 27 2,700 50 lbs. 1,350 lbs. 495 lbs.

1/2 10-1/8 CA08‐162‐11 75 27 2,025 51 lbs. 1,377 lbs. 680 lbs.
1/2 12-1/8 CA08‐194‐11
Concrete Anchors are used in all types of concrete connections. They can be
welded to a flat surface, or to the inside or outside of an angle. Mechanical Property Requirements
Length: Length is listed before weld. Stud diameters 1/2” will be approx. 1/8”
shorter after welding. TRU‐WELD concrete anchors can be made in any length Type A Type B
above the standard minimum. 61,000 psi 65,000 psi
Material: Low carbon steel, ASTM A29, 1010‐1020. CA Studs are also available Tensile Strength
min. min.
in weldable stainless steel. Type 302 is the most commonly used. 49,000 psi 51,000 psi
Yield Strength
min. min.
CHUCK FOOT GRIP FERRULE FOOT PLATE Elongation (% in 2 in.) 17% min. 20% min.
PART # PART # PART # (DUAL LEG) Elongation (% in 5x dia.) 14% min. 15% min.
GC‐050 (Standard QN‐050 Reduction of Area 50% min. 50% min.
B‐1C

CH‐050 Type A Studs are general purpose studs.
GC‐062 QN‐062
B‐2C
(Heavy Duty) (Heavy Duty) Type B Studs are headed, bent, or of other configuration that are
used as an essential component in composite beam design and
construction.



TYPE CA STUD

Head Diameter (HD) – 1‐1/4” for all 5/8” Headed Concrete Anchors.


Box Pallet 1,000 Piece
Diameter Length Per Per Per
Part Number Weight Weight Weight
Box Pallet Pallet
5/8 1-7/16 CA10‐023‐11 400 27 10,800 85 lbs. 2,295 lbs. 208 lbs.
5/8 1-11/16 CA10‐027‐11 325 27 8,775 77 lbs. 2,079 lbs. 227 lbs.
5/8 1-15/16 CA10‐031‐11 300 27 8,100 78 lbs. 2,106 lbs. 248 lbs.
5/8 2-1/8 CA10‐034‐11 250 27 6,750 68 lbs. 1,836 lbs. 264 lbs.
5/8 2-3/16 CA10‐035‐11 250 27 6,750 71 lbs. 1,917 lbs. 270 lbs.
5/8 2-11/16 CA10‐043‐11 250 27 6,750 81 lbs. 2,187 lbs. 319 lbs.
5/8 3-3/16 CA10‐051‐11 200 27 5,400 75 lbs. 2,025 lbs. 363 lbs.
5/8 3-11/16 CA10‐059‐11 150 27 4,050 75 lbs. 1,674 lbs. 398 lbs.
5/8 4-3/16 CA10‐067‐11 150 27 4,050 62 lbs. 1,863 lbs. 444 lbs.
5/8 4-11/16 CA10‐075‐11 125 27 3,375 69 lbs. 1,701 lbs. 487 lbs.
Length: Length is listed before weld. Stud diameters 5/8” will be approx. 3/16”
shorter after welding. TRU‐WELD concrete anchors can be made in any length
above the standard minimum. Type A Type B
Material: Low carbon steel, ASTM A29, 1010‐1020. CA Studs are also available 61,000 psi 65,000 psi
in weldable stainless steel. Type 302 is the most commonly used. Tensile Strength
min. min.
49,000 psi 51,000 psi
Yield Strength
min. min.

Elongation (% in 2 in.) 17% min. 20% min.

CHUCK FOOT GRIP FERRULE FOOT PLATE
PART # PART # PART # (DUAL LEG) Reduction of Area 50% min. 50% min.
GC‐062 (Standard QN‐062
B‐2C
Type A Studs are general purpose studs.
CH‐075
GC‐075 QN‐075
B‐2C Type B Studs are headed, bent, or of other configuration that
are used as an essential component in composite beam design
and construction.



TYPE CA STUD

Head Diameter (HD) – 1‐1/4” for all 5/8” Headed Concrete Anchors.


Box Pallet
1,000
5/8 5-3/16 CA10‐083‐11 100 27 2,700 55 lbs. 1,485 lbs. 528 lbs.
5/8 6-9/16 CA10‐105‐11 90 27 2,430 55 lbs. 1,485 lbs. 604 lbs.
5/8 8-3/16 CA10‐131‐11 80 27 2,160 52 lbs. 1,404 lbs. 646 lbs.
5/8 9-3/16 CA10‐147‐11 150 9 1,350 117 lbs. 1,053 lbs. 781 lbs.
5/8 10-3/16 CA10‐16311 100 9 900 98 lbs. 882 lbs. 946 lbs.
Length: Length is listed before weld. Stud diameters 5/8” will be approx.
3/16” shorter after welding. TRU‐WELD concrete anchors can be made in any
length above the standard minimum. Type A Type B
Material: Low carbon steel, ASTM A29, 1010‐1020. CA Studs are also 61,000 psi 65,000 psi
available in weldable stainless steel. Type 302 is the most commonly used. Tensile Strength
min. min.
49,000 psi 51,000 psi
Yield Strength
min. min.

CHUCK FOOT GRIP FERRULE FOOT PLATE
Reduction of Area 50% min. 50% min.
GC‐062 (Standard QN‐062
B‐2C
Duty) (Standard Duty) Type A Studs are general purpose studs.
CH‐075
GC‐075 QN‐075 Type B Studs are headed, bent, or of other configuration that
B‐2C are used as an essential component in composite beam design
and construction.


SHEAR CONNECTOR – FULL WELD BASE
(3/4” THRU DECK SHEAR CONNECTORS ON NEXT PAGE)

TYPE SC STUD

Head Diameter (HD) – 1‐1/4” for all 3/4 headed Shear Connectors.
Head Height (HT) – 3/8” for all 3/4 headed Shear Connectors.


Box Pallet
1,000
3/4 3-3/16 SC12‐051‐11 125 48 6,000 60 lbs. 2,880 lbs. 478 lbs.
3/4 3-11/16 SC12‐059‐11 100 48 4,800 55 lbs. 2,640 lbs. 548 lbs.
3/4 4-3/16 SC12‐067‐11 100 48 4,800 63 lbs. 3,024 lbs. 600 lbs.
3/4 4-11/16 SC12‐075‐11 75 27 2,025 51 lbs. 1,377 lbs. 672 lbs.
3/4 5-3/16 SC12‐083‐11 60 48 2,880 43 lbs. 2,064 lbs. 735 lbs.
3/4 5-11/16 SC12‐091‐11 60 48 2,880 47 lbs. 2.256 lbs. 783 lbs.
3/4 6-3/16 SC12‐099‐11 60 48 2,880 51 lbs. 2,448 lbs. 852 lbs.
3/4 6-11/16 SC12‐107‐11 80 27 2,160 75 lbs. 2,025 lbs. 938 lbs.
3/4 7-3/16 SC12‐115‐11 60 27 1,620 59 lbs. 1,593 lbs. 968 lbs.
3/4 8-3/16 SC12‐131‐11 50 27 1,350 56 lbs. 1,512 lbs. 1,105 lbs.
3/4 9-3/16 SC12‐147‐11 100 9 900 123 lbs. 1,107 lbs. 1,222 lbs.
3/4 10-3/16 SC12‐163‐11 100 9 900 137 lbs. 1,233 lbs. 1,339 lbs.
3/4 12-3/16 SC12‐195‐11 1,100 1 1,100 1,760 lbs. 1,760 lbs. 1,599 lbs.
3/4 16-3/16 SC12‐259‐11 1,000 1 1,000 2,000 lbs. 2,000 lbs. 2,000 lbs.

Shear Connectors are used in all types of concrete
connections. They can be welded to a flat surface, or to the Mechanical Property Requirements
Type A Type B
be approx. 3/16” shorter after weld. 61,000 psi 65,000 psi
Tensile Strength
TRU‐WELD shear connectors can be made in any length min. min.
above the standard minimum. 49,000 psi 51,000 psi
Yield Strength
Material: Low carbon steel, ASTM A29, 1010‐1020. SC Studs min. min.
are also available in weldable stainless steel. Type 302 is the Elongation (% in 2 in.) 17% min. 20% min.
most commonly used.
Elongation (% in 5x
14% min. 15% min.
dia.)
CHUCK FOOT GRIP FERRULE FOOT Reduction of Area 50% min. 50% min.
PART # PART # PART # PLATE (DUAL LEG)
CH‐075 B‐2C GC‐075 QN‐075 Type A Studs are general purpose studs.
Type B Studs are headed, bent, or of other configuration that
d t ti


THRU‐DECK SHEAR CONNECTOR

TYPE DSC STUD


Head Diameter (HD) – 1‐1/4” for all 3/4” Thru‐Deck Shear Connectors.
Head Height (HT) – 3/8” for all 3/4” Thru‐Deck Shear Connectors.


Box Pallet
1,000
3/4 3-3/8 DSC12‐054‐11 125 48 6,000 62 lbs. 2,976 lbs. 500 lbs.

3/4 3-7/8 DSC12‐062‐11 100 48 4,800 58 lbs. 2,784 lbs. 567 lbs.
3/4 4-3/8 DSC12‐070‐11 100 48 4,800 62 lbs. 2,976 lbs. 634 lbs.
3/4 4-7/8 DSC12‐078‐11 75 48 3,600 51 lbs. 2,448 lbs. 701 lbs.
3/4 5-3/8 DSC12‐086‐11 60 48 2,880 45 lbs. 2,160 lbs. 754 lbs.

3/4 5-7/8 DSC12‐094‐11 60 48 2,880 49 lbs. 2,352 lbs. 810 lbs.

3/4 6-3/8 DSC12‐102‐11 60 48 2,880 53 lbs. 2,544 lbs. 883 lbs.

Thru‐Deck Shear Connectors are used in all types of concrete


Length: Length is listed before weld. Stud diameters 3/4” will Type A Type B
be approx. 3/8” shorter after weld.
TRU‐WELD thru‐deck shear connectors can be made in any 61,000 psi 65,000 psi
Tensile Strength
length above the standard minimum. min. min.
Material: Low carbon steel, ASTM A29, 1010‐1020. DSC Studs 49,000 psi 51,000 psi
Yield Strength
are also available in weldable stainless steel. Type 302 is the min. min.
most commonly used.

CHUCK THRU‐DECK FOOT THRU‐DECK FERRULE
PART # ASSEMBLY GRIP Reduction of Area 50% min. 50% min.
B‐0021‐1A
CH‐075 B‐0060‐1 Type A Studs are general purpose studs.

B‐0021‐1P Type B Studs are headed, bent, or of other configuration that
and construction.



TYPE SC STUD

Head Diameter (HD) – 1‐3/8” for all 7/8” Shear Connectors.
Head Height (HT) – 3/8” for all 7/8” Shear Connectors.


Box Pallet
1,000
7/8 3-3/16 SC14‐051‐11 100 27 2,700 66 lbs. 1,782 lbs. 660 lbs.

7/8 3-11/16 SC14‐059‐11 100 27 2,700 74 lbs. 1,998 lbs. 709 lbs.
7/8 4-3/16 SC14‐067‐11 100 27 2,700 80 lbs. 2,160 lbs. 796 lbs.
7/8 5-3/16 SC14‐083‐11 75 27 2,025 73 lbs. 1,971 lbs. 961 lbs.
7/8 6-3/16 SC14‐099‐11 50 27 1,350 57 lbs. 1,539 lbs. 1,137 lbs.

7/8 7-3/16 SC14‐115‐11 45 27 1,215 59 lbs. 1,593 lbs. 1,306 lbs.

7/8 8-3/16 SC14‐131‐11 40 27 1,080 59 lbs. 1,593 lbs. 1,496 lbs.
7/8 9-3/16 SC14‐147‐11 75 9 675 125 lbs. 1,125 lbs. 1,666 lbs.
7/8 10-3/16 SC14‐163‐11 75 9 675 135 lbs. 1,215 lbs. 1,836 lbs.

7/8 12-3/16 SC14‐195‐11 825 1 825 1,793 lbs. 1,793 lbs. 2,173 lbs.

Type A Type B
be approx. 3/16”shorter after weld. 61,000 psi 65,000 psi
TRU‐WELD shear connectors can be made in any length above Tensile Strength
min. min.
the standard minimum. 49,000 psi 51,000 psi
Material: Low carbon steel, ASTM A29, 1010‐1020. SC Studs Yield Strength
min. min.
most commonly used. Elongation (% in 2 in.) 17% min. 20% min.
Elongation (% in 5x
14% min. 15% min.
dia.)
CHUCK FOOT GRIP FERRULE FOOT
PART # PART # PART # PLATE (DUAL LEG) Reduction of Area 50% min. 50% min.
CH‐087 B‐3C GC‐087 QN‐087

and construction.



TYPE SC STUD

Head Diameter (HD) – 1‐5/8” for all 1” Shear Connectors.
Head Height (HT) – 1/2” for all 1” Shear Connectors.


Box Pallet
1,000
1” 3-1/4 SC16‐052‐11 75 27 2,025 70 lbs. 1,890 lbs. 894 lbs.

1” 4-1/4 SC16‐068‐11 50 27 1,350 57 lbs. 1,539 lbs. 1,079 lbs.
1” 5-1/4 SC16‐084‐11 50 27 1,350 70 lbs. 1,890 lbs. 1,302 lbs.
1” 6-1/4 SC16‐100‐11 40 27 1,080 63 lbs. 1,701lbs. 1,514 lbs.
1” 7-1/4 SC16‐116‐11 85 9 765 154 lbs. 1,386 lbs. 1,737 lbs.

1” 8-1/4 SC16‐132‐11 85 9 765 173 lbs. 1,557 lbs. 1,978 lbs.

1” 9-1/4 SC16‐148‐11 80 9 720 180 lbs. 1,620 lbs. 2,193 lbs.



Length: Length is listed before weld. Stud diameters 1” will be Type A Type B
approx. 1/4” shorter after weld.
TRU‐WELD shear connectors can be made in any length above 61,000 psi 65,000 psi
Tensile Strength
the standard minimum. min. min.
Material: Low carbon steel, ASTM A29, 1010‐1020. SC Studs 49,000 psi 51,000 psi
Yield Strength
are also available in weldable stainless steel. Type 302 is the min. min.
most commonly used.

CHUCK FOOT GRIP FERRULE FOOT
PART # PART # PART # PLATE (DUAL LEG) Reduction of Area 50% min. 50% min.
CH‐100 B‐3C GC‐100 QN‐100

and construction.


DEFORMED BAR ANCHORS
TYPE DBA STUD
NO THREAD – FULL WELD BASE

Box Pallet Pallet
3/8 10-1/8 DBA06‐162‐18 150 18 2,700 46 lbs. 828 lbs. 288 lbs.
3/8 12-1/8 DBA06‐194‐18 150 18 2,700 55 lbs. 990 lbs. 344 lbs.
3/8 18-1/8 DBA06‐290‐18 150 12 1,800 80 lbs. 960 lbs. 515 lbs.
3/8 24-1/8 DBA06‐386‐18 150 8 1,200 108 lbs. 864 lbs. 685 lbs.
3/8 30-1/8 DBA06‐482‐18 150 7 1,050 130 lbs. 910 lbs. 897 lbs.
3/8 36-1/8 DBA06‐576‐18 150 6 900 156 lbs. 936 lbs. 1,029 lbs.
3/8 48-1/8 DBA06‐770‐18 150 6 900 208 lbs. 1,248 lbs. 1,394 lbs.

Deformed Bar Anchors are designed for weld and bearing

plates in concrete connections.

Length: Length is listed before weld. Stud diameters 3/8” and

below will be approx. 1/8” shorter after welding. Type C

80,000 psi min.
TRU‐WELD Deformed Bar Anchors can be made in any length Tensile Strength
(552 MPa)
above the standard minimum.

70,000 psi min.
Yield Strength (0.5% offset)
Material: Low carbon steel ASTM A496 (485 MPa)

CHUCK FOOT GRIP FERRULE FOOT Type “C” Studs are cold‐worked deformed steel bars
PART # PART # PART # PLATE (DUAL LEG) manufactured in accordance with specification ASTM A496
having a nominal diameter equivalent to the diameter of a
GC‐037 QN‐037
B‐1C plain wire having the same weight per foot as the deformed
(Standard Duty) (Standard Duty wire. ASTM A496 specifies a maximum diameter of 0.628 in.
CN‐037
GC‐050 QN‐050 (16mm). Any bar supplied above that diameter must have the
B‐1C same physical characteristics regarding deformations as
required by ASTM A496.



TYPE DBA STUD

Box Pallet Pallet
1/2 8-1/8 DBA08‐130‐18 100 18 1,800 44 lbs. 792 lbs. 451 lbs.
1/2 10-1/8 DBA08‐162‐18 100 18 1,800 54 lbs. 972 lbs. 529 lbs.
1/2 12-1/8 DBA08‐194‐18 100 18 1,800 67 lbs. 1,206 lbs. 680 lbs.
1/2 18-1/8 DBA08‐290‐18 100 12 1,200 98 lbs. 1,176 lbs. 972 lbs.
1/2 24-1/8 DBA08‐386‐18 100 8 800 128 lbs. 1,024 lbs. 1,292 lbs.
1/2 30-1/8 DBA08‐482‐18 100 7 700 160 lbs. 1,120 lbs. 1,560 lbs.
1/2 36-1/8 DBA08‐578‐18 100 6 600 192 lbs. 1,152 lbs. 1,879 lbs.
1/2 42-1/8 DBA08‐674‐18 100 6 600 222 lbs. 1,332 lbs. 2,174 lbs.
1/2 48-1/8 DBA08‐770‐18 100 6 600 256 lbs. 1,536 lbs. 2,502 lbs.
1/2 60-1/8 DBA08‐962‐18 100 1 100 314 lbs. 314 lbs. 3,140 lbs.

plates in concrete connections. Mechanical Property Requirements

Length: Length is listed before weld. Stud diameters 1/2” will Type C
be approx. 1/8” shorter after welding.
80,000 psi min.
Tensile Strength
TRU‐WELD Deformed Bar Anchors can be made in any length (552 MPa)
above the standard minimum. 70,000 psi min.
(485 MPa)
Material: Low carbon steel ASTM A496
Type “C” Studs are cold‐worked deformed steel bars
manufactured in accordance with specification ASTM A496
CHUCK FOOT GRIP FERRULE FOOT PLATE plain wire having the same weight per foot as the deformed
PART # PART # PART # (DUAL LEG) wire. ASTM A496 specifies a maximum diameter of 0.628 in.
GC‐050 QN‐050 (16mm). Any bar supplied above that diameter must have the
B‐1C same physical characteristics regarding deformations as
(Standard Duty) (Standard Duty)
CN‐050 required by ASTM A496.
GC‐062 QN‐062
B‐2C


TYPE DBA STUD


Box Pallet
1,000
5/8 12-3/16 DBA10‐195‐18 50 18 900 51 lbs. 918 lbs. 997 lbs.

5/8 18-3/16 DBA10‐291‐18 50 12 600 76 lbs. 912 lbs. 1,633 lbs.

5/8 24-3/16 DBA10‐387‐18 50 8 400 102 lbs. 816 lbs. 2,136 lbs.
5/8 30-3/16 DBA10‐483‐18 50 7 350 126 lbs. 882 lbs. 2,666 lbs.
5/8 36-3/16 DBA10‐579‐18 50 6 300 151 lbs. 906 lbs. 3,196 lbs.

5/8 42-3/16 DBA10‐675‐18 50 8 400 176 lbs. 1,408 lbs. 3,482 lbs.

5/8 48-3/16 DBA10‐771‐18 50 6 300 197 lbs. 1,182 lbs. 3,962 lbs.

Deformed Bar Anchors are designed for weld and bearing Mechanical Property Requirements
Type C
Length: Length is listed before weld. Stud diameters 5/8”
80,000 psi min.
will be approx. 3/16” shorter after welding. Tensile Strength
(552 MPa)

TRU‐WELD Deformed Bar Anchors can be made in any 70,000 psi min.
length above the standard minimum. (485 MPa)

Type C Studs are cold‐worked deformed steel bars
Material: Low carbon steel ASTM A496 manufactured in accordance with specification ASTM A496
plain wire having the same weight per foot as the deformed
CHUCK FOOT GRIP FERRULE FOOT wire. ASTM A496 specifies a maximum diameter of 0.628 in.
(16mm). Any bar supplied above that diameter must have the
PART # PART # PART # PLATE (DUAL LEG) same physical characteristics regarding deformations as
GC‐062 QN‐062 required by ASTM A496.
B‐2C
CN‐062
GC‐075 QN‐075
B‐2C



TYPE DBA STUD


Box Pallet
1,000
3/4 12-3/16 DBA12‐195‐18 40 18 720 60 lbs. 1,080 lbs. 1,525 lbs.

3/4 18-3/16 DBA12‐291‐18 40 12 480 87 lbs. 1,044 lbs. 2,276 lbs.

3/4 24-3/16 DBA12‐387‐18 40 8 320 115 lbs. 920 lbs. 3,027 lbs.
3/4 30-3/16 DBA12‐483‐18 40 6 240 142 lbs. 852 lbs. 3,778 lbs.
3/4 36-3/16 DBA12‐579‐18 40 6 240 175 lbs. 1,050 lbs. 4,529 lbs.

3/4 42-3/16 DBA12‐675‐18 40 6 240 205 lbs. 1,230 lbs. 5,125 lbs.

3/4 48-3/16 DBA12‐771‐18 40 6 240 226 lbs. 1,356 lbs. 5,650 lbs.

be approx. 3/16” shorter after welding. Type C

TRU‐WELD Deformed Bar Anchors can be made in any length 80,000 psi min.
Tensile Strength
above the standard minimum. (552 MPa)
70,000 psi min.
Material: Low carbon steel ASTM A496 (485 MPa)
FOOT Type “C” Studs are cold‐worked deformed steel bars

CHUCK GRIP FERRULE FOOT manufactured in accordance with specification ASTM A496
PART
PART # PART # PLATE (DUAL LEG) having a nominal diameter equivalent to the diameter of a
# plain wire having the same weight per foot as the deformed
GC‐075 QN‐075 wire. ASTM A496 specifies a maximum diameter of 0.628 in.
CN‐075 B‐2C (16mm). Any bar supplied above that diameter must have the
same physical characteristics regarding deformations as
required by ASTM A496.


PUNCHING SHEAR RESISTOR

TYPE PSR STUD

WELD STUD SPECIFICATIONS
D L TRU‐WELD HD HT FD FH

Part Number Head Head Fillet Fillet
Diameter Length
Diameter Height Diameter Height
3/8 3-7/16 PSR06‐055‐11 1.190 .260 1/2 1/8
1/2 2-5/8 PSR08‐042‐11 1.580 .330 11/16 5/32
5/8 3-3/4 PSR08‐060‐11 1.980 .400 7/8 3/16
3/4 4-3/8 PSR08‐070‐11 2.370 .470 1-1/16 1/4

1) Tru‐Weld studs are available in any length above the standard
minimum. Mechanical Property Requirements
2) Listed Ferrule above is for the standard flat down hand position.
Type B
Tensile Strength 65,000 psi min.
FOOT GRIP FERRULE FOOT PLATE Yield Strength 51,000 psi min.

Diameter
PART # PART # (DUAL LEG)
3/8 B‐1C GC‐037 QN‐037 Elongation (% in 2 in.) 20% min.
1/2 B‐1C GC‐050 QN‐050
Elongation (% in 5x dia.) 15% min.
5/8 B‐2C GC‐062 QN‐062
3/4 B‐2C GC‐075 QN‐075 Reduction of Area 50% min.


NO THREAD STUD – FULL WELD BASE

TYPE NT STUD


D L TRU‐WELD FD FH Ferrule

Stud Length Part Number Weld Fillet Weld Fillet
Part Number
Diameter (BW) Diameter Height
1/4 7/8 NT04‐014‐11 23/64 7/64 FER04‐F
5/16 7/8 NT05‐014‐11 7/16 7/64 FER05‐F
3/8 7/8 NT06‐014‐11 1/2 1/8 FER06‐F
7/16 1 NT07‐016‐11 19/32 9/64 FER07‐F
1/2 1 NT08‐016‐11 11/16 5/32 FER08‐F
5/8 1‐5/16 NT10‐021‐11 7/8 3/16 FER10‐F
3/4 1‐5/16 NT12‐021‐11 1‐1/16 1/4 FER12‐F
7/8 1‐9/16 NT14‐025‐11 1‐1/8 5/16 FER14‐F
1 1‐7/8 NT16‐030‐11 1‐3/8 3/8 FER16‐F

NT Studs are used in all types of applications. They can be welded to a flat
surface, or to the inside or outside of an angle. Mechanical Property Requirements
Length: Length is listed before weld. Stud diameters 1/2” and below will Tensile Strength 55,000 psi min.
be approx. 1/8” shorter after welding. 5/8” will be approx. 3/16” shorter Yield Strength 50,000 psi min.
after welding.
TRU‐WELD NT Studs can be made in any length above the standard Elongation (% in 2 in.) 17% min.
minimum. Elongation (% in 5x dia.) 14% min.
Material: Low carbon steel, ASTM A29, 1010‐1020. NT Studs are also Reduction of Area 50% min.
available in weldable stainless steel.
Light Duty Light Duty Standard

Standard Split Combination
FOOT AND
DIAMETER CHUCK PART # FOOT PART # GRIP PART # FOOT PART # GRIP PART #
GRIP #
1/4 CN‐025 B‐1N GN‐025 B‐1C GC‐025 QM‐025
5/16 CN‐031 B‐1N GN‐031 B‐1C GC‐031 QM‐031
3/8 CN‐037 B‐1N GN‐050 B‐1C GC‐050 QM‐050
7/16 CN‐043 B‐1N GN‐043 B‐1C GC‐043 QM‐044
1/2 CN‐050 B‐2N GN‐062 B‐2C GC‐062 QM‐062
5/8 CN‐062 B‐2N GN‐075 B‐2C GC‐075 QM‐075
3/4 CN‐075 B‐2N GN‐075 B‐2C GC‐075 QM‐075
7/8 CN‐087 B‐3N GN‐087 B‐3C GC‐087 QM‐087
1 CN‐100 B‐3N GN‐100 B‐3C GC‐100 QM‐100

FULL THREAD STUD – FULL WELD BASE
TYPE TT STUD


D L TRU‐WELD FD FH Ferrule

Mechanical Property
Stud Length Weld Fillet Weld Fillet Requirements
Diameter (BW)
Part Number Diameter Height
Part Number
55,000 psi
Tensile Strength
1/4‐20 3/4 TT04‐012‐11 23/64 7/64 FER04‐F min.
5/16‐18 3/4 TT05‐012‐11 7/16 7/64 FER05‐F 50,000 psi
Yield Strength
3/8‐16 3/4 TT06‐012‐11 1/2 1/8 FER06‐F min.
7/16‐14 7/8 TT07‐014‐11 19/32 9/64 FER07‐F Elongation (% in 2
17% min.
1/2‐13 7/8 TT08‐014‐11 11/16 5/32 FER08‐F in.)
5/8‐11 1 TT10‐016‐11 7/8 3/16 FER10‐F Elongation (% in
14% min.
3/4‐10 1‐3/16 TT12‐019‐11 1‐1/16 1/4 FER12‐F 5x dia.)
7/8‐9 1‐11/16 TT14‐027‐11 1‐1/8 5/16 FER14‐F
Reduction of Area 50% min.
1‐8 1‐11/16 TT16‐027‐11 1‐3/8 3/8 FER16‐F
Full Thread Studs are used in all types of applications. They can be welded to a flat surface, or to the inside or outside of
an angle.
Length: Length is listed before weld. Stud diameters 1/2” and below will be approx. 1/8” shorter after welding. 5/8” will
be approx. 3/16” shorter after welding.
TRU‐WELD TT Studs can be made in any length above the standard minimum.
Material: Low carbon steel, ASTM A29, 1010‐1020. TT Studs are also available in weldable stainless steel. Type 302 is the
most commonly used. Other grades of stainless steel (except Type 303) are available when required.

CHUCK FOOT AND
DIAMETER FOOT PART # GRIP PART # FOOT PART # GRIP PART #
PART # GRIP #
1/4 CN‐025 B‐1N GN‐025 B‐1C GC‐025 QN‐025
5/16 CN‐031 B‐1N GN‐031 B‐1C GC‐031 QN‐031
3/8 CN‐037 B‐1N GN‐050 B‐1C GC‐050 QN‐050
7/16 CN‐043 B‐1N GN‐043 B‐1C GC‐043 QN‐044
1/2 CN‐050 B‐1C GN‐062 B‐2C GC‐062 QN‐062
5/8 CN‐062 B‐1C GN‐075 B‐2C GC‐075 QN‐075
3/4 CN‐075 B‐1C GN‐075 B‐2C GC‐075 QN‐075
7/8 CN‐087 B‐3N GN‐087 B‐3C GC‐087 QN‐087
1 CN‐100 B‐3N GN‐100 B‐3C GC‐100 QN‐100


PARTIAL THREAD STUD
TYPE TP STUD
TYPE P FERRULE SUPPLIED

D L TRU‐WELD B U FD FH Ferrule
Stud Length Part Number Base Base Weld Fillet Weld Fillet Part Number
Diameter (BW) Diameter Length Diameter Height
1/4‐20 3/4 TP04‐012‐11 .215 3/8 5/16 3/32 FER04‐P
5/16‐18 3/4 TP05‐012‐11 .275 3/8 13/32 7/64 FER05‐P
3/8‐16 3/4 TP06‐012‐11 .330 13/32 7/16 7/64 FER06‐P
7/16‐14 7/8 TP07‐014‐11 .87 7/16 1/2 1/8 FER07‐P
1/2‐13 7/8 TP08‐014‐11 .448 1/2 19/32 5/32 FER08‐P
5/8‐11 1 TP10‐016‐11 .562 5/8 3/4 3/16 FER10‐P
3/4‐10 1‐3/16 TP12‐019‐11 .680 13/16 7/8 1/4 FER12‐P
7/8‐9 1‐11/16 TP14‐027‐11 .798 7/8 1 5/16 FER14‐P
1‐8 1‐11/16 TP16‐027‐11 .915 15/16 1‐1/8 5/16 FER16‐P

TP STUDS are used in all types of applications. Mechanical Property Requirements
Length: TRU‐WELD TP Studs can be made in any length
Yield Strength 50,000 psi min.
above the standard minimum.
Elongation (% in 2 in.) 17% min.

Material: Low Carbon Steel, ASTM A29, 1010‐1020. TP Elongation (% in 5x dia.) 14% min.
Studs are also available in weldable stainless steel. Reduction of Area 50% min.

CHUCK FOOT AND
PART # GRIP #
1/4 CN‐025 B‐1N GN‐025 B‐1C GC‐025 QN‐025
5/16 CN‐031 B‐1N GN‐031 B‐1C GC‐031 QN‐031
3/8 CN‐037 B‐1N GN‐050 B‐1C GC‐050 QN‐050
7/16 CN‐043 B‐1N GN‐043 B‐1C GC‐043 QN‐044
1/2 CN‐050 B‐1C GN‐062 B‐2C GC‐062 QN‐062
5/8 CN‐062 B‐1C GN‐075 B‐2C GC‐075 QN‐075
3/4 CN‐075 B‐1C GN‐075 B‐2C GC‐075 QN‐075
7/8 CN‐087 B‐3N GN‐087 B‐3C GC‐087 QN‐087
1 CN‐100 B‐3N GN‐100 B‐3C GC‐100 QN‐100


THREADED STUD – REDUCED WELD BASE
TYPE TR STUD

TYPE R FERRULE SUPPLIED

D L TRU‐WELD B U FD FH Ferrule

Stud Length Base Base Weld Fillet Weld Fillet Part Number
Diameter (BW)
Part Number Diameter Length Diameter Height
3/8‐16 3/4 TR06‐012‐11 .310 3/8 7/16 7/64 FER06‐R

7/16‐14 7/8 TR07‐014‐11 .373 3/8 1/2 1/8 FER07‐R
1/2‐13 7/8 TR08‐014‐11 .435 7/16 19/32 9/64 FER08‐R
5/8‐11 1 TR10‐016‐11 .500 1/2 11/16 5/32 FER10‐R
3/4‐10 1‐3/16 TR12‐019‐11 .625 5/8 7/8 3/16 FER12‐R

TR Studs are used in all types of applications. They can be welded to a flat
surface, or to the inside or outside of an angle. Mechanical Property Requirements
Length: Length is listed before weld. Stud diameters 1/2” and below will be 55,000 psi
approx. 1/8” shorter after welding. 5/8” will be approx. 3/16” shorter after Tensile Strength
min.
welding. 50,000 psi
TRU‐WELD TR Studs can be made in any length above the standard Yield Strength
min.
minimum.
Material: Low carbon steel, ASTM A29, 1010‐1020. TR Studs are also Elongation (% in 2 in.) 17% min.
available in weldable stainless steel. Type 302 is the most commonly used.
Other grades of stainless steel (except Type 303) are available when Elongation (% in 5x dia.) 14% min.
required

CHUCK FOOT AND
PART # GRIP #
3/8 CN‐037 B‐1N GN‐037 B‐1C GC‐037 QN‐037
7/16 CN‐043 B‐1N GN‐043 B‐1C GC‐043 QN‐044
1/2 CN‐050 B‐1N GN‐050 B‐1C GC‐050 QN‐050
5/8 CN‐062 B‐2N GN‐062 B‐2C GC‐062 QN062
3/4 CN‐075 B‐2N GN‐075 B‐2C GC‐075 QN‐075



COLLAR STUD

TYPE CS STUD

THREADED TO COLLAR– PITCH DIAMETER WELD BASE
TYPE c FERRULE SUPPLIED

D T TRU‐WELD B T FD FH Ferrule

Thread Thread Base Stud Weld Fillet Weld Fillet Part Number
Diameter Length
1/4‐20 1/4 CS03‐008‐11‐04‐004 .215 1/2 23/64 7/64 FER04‐C

5/16‐18 3/8 CS04‐008‐11‐05‐006 .275 1/2 7/16 7/64 FER05‐C
3/8‐16 3/8 CS05‐008‐11‐06‐006 .330 1/2 1/2 1/8 FER06‐C
1/2‐13 3/8 CS07‐009‐11‐08‐006 .448 9/16 11/16 5/32 FER08‐C

Collar Studs are used in all types of applications. They can be welded
to a flat surface, or on the inside or outside of an angle. Mechanical Property Requirements
Length: Length is listed before weld. Stud diameters 1/2” and below
will be approx. 1/8” shorter after welding. Tensile Strength 55,000 psi min.
TRU‐WELD Collar Studs can be made in any length above the standard
minimum. Yield Strength 50,000 psi min.
Material: Low carbon steel, ASTM A29, 1010‐1020. Collar Studs are
also available in weldable stainless steel. Type 302 is the most Elongation (% in 2 in.) 17% min.
commonly used. Other grades of stainless steel (except Type 303) are
available when required. Elongation (% in 5x dia.) 14% min.


THREAD CHUCK FOOT AND
FOOT PART # GRIP PART # FOOT PART # GRIP PART #
DIAMETER PART # GRIP #
1/4” CN‐031 B‐2N GN‐062 B‐2C GC‐062 QN‐062
5/16” CN‐037 B‐2N GN‐062 B‐2C GC‐062 QN‐062
3/8” CN‐043 B‐2N GN‐062 B‐2C GC‐062 QN‐062
1/2” CN‐050 B‐2N GN‐075 B‐2C GC‐075 QN‐075


INTERNALLY TAPPED STUD – FULL WELD BASE

TYPE IT STUD


B D L T TRU‐WELD FD FH Ferrule

Stud Tap Length Tap Part Number Weld Fillet Weld Fillet Part Number
Diameter Diameter (BW) Depth Diameter Height
1/4 #8‐32 5/8 1/4 IT04‐010‐11‐IC‐004 23/64 7/64 FER04‐F
5/16 #10‐24 5/8 5/16 IT05‐010‐11‐KF‐005 7/16 7/64 FER05‐F
3/8 1/4‐20 13/16 3/8 IT06‐013‐11‐04‐006 1/2 1/8 FER06‐F
7/16 5/16‐18 1 1/2 IT07‐016‐11‐05‐008 19/32 9/64 FER07‐F
1/2 3/8‐16 1‐1/8 9/16 IT08‐018‐11‐06‐009 11/16 5/32 FER08‐F
5/8 7/16‐14 1‐3/16 5/8 IT10‐019‐11‐07‐010 7/8 3/16 FER10‐F
3/4 1/2‐13 1‐7/16 3/4 IT12‐023‐11‐08‐012 1‐1/16 1/4 FER12‐F
7/8 5/8‐11 1‐5/8 15/16 IT14‐026‐11‐10‐015 1‐1/8 5/16 FER14‐F
1 3/4‐10 2‐1/4 1‐1/8 IT16‐036‐11‐12‐018 1‐3/8 3/8 FER16‐F

Tapped Studs are used in all types of applications. They can be Mechanical Property Requirements
welded to a flat surface, or to the inside or outside of an angle.
Length: Length is listed before weld. Diameters 1/2” and below
will be approx. 1/8” shorter after weld. 5/8” and above will be Yield Strength 50,000 psi min.
3/16” shorter. TRU‐WELD IT Studs can be made in any length Elongation (% in 2 in.) 17% min.
above the standard minimum. Elongation (% in 5x dia.) 14% min.
Material: Low Carbon Steel, ASTM A29, 1010‐1020. IT Studs are Reduction of Area 50% min.
also available in weldable stainless steel.
Light Duty Standard

Light Duty Split
Standard Combination
CHUCK FOOT AND
PART # GRIP #
1/4 CN‐025 B‐1N GN‐025 B‐1C GC‐025 QN‐025
5/16 CN‐031 B‐1N GN‐031 B‐1C GC‐031 QN‐031
3/8 CN‐037 B‐1N GN‐050 B‐1C GC‐050 QN‐050
7/16 CN‐043 B‐1N GN‐043 B‐1C GC‐043 QN‐044
1/2 CN‐050 B‐1C GN‐062 B‐2C GC‐062 QN‐062
5/8 CN‐062 B‐1C GN‐075 B‐2C GC‐075 QN‐075
3/4 CN‐075 B‐1C GN‐075 B‐2C GC‐075 QN‐075
7/8 CN‐087 B‐3N GN‐087 B‐3C GC‐087 QN‐087
1 CN‐100 B‐3N GN‐100 B‐3C GC‐100 QN‐100



SHOULDER STUD – FULL WELD BASE
TYPE S STUD


D T TRU‐WELD B T FD FH Ferrule

Thread Thread Base Stud Weld Fillet Weld Fillet Part Number
Diameter Length
1/4‐20 3/8 3011‐06‐012‐04‐006 3/8 3/4 1/2 1/8 FER06‐F
5/16‐18 7/16 3011‐07‐014‐05‐007 7/16 7/8 19/32 9/64 FER07‐F
3/8‐16 1/2 3011‐08‐016‐06‐008 1/2 1 11/16 5/32 FER08‐F
1/2‐13 11/16 3011‐10‐020‐08‐011 5/8 1‐1/4 7/8 3/16 FER10‐F
5/8‐11 11/16 3011‐12‐025‐10‐011 3/4 1‐9/16 1‐1/16 1/4 FER12‐F
3/4‐10 13/16 3011‐14‐030‐12‐013 7/8 1‐7/8 1‐1/8 5/16 FER14‐F

S Studs are used in all types of applications. They can be welded to a Mechanical Property Requirements
flat surface, or to the inside or outside of an angle.
Length: Length is listed before weld. Stud diameters 1/2” and below Tensile Strength 55,000 psi min.
will be approx. 1/8” shorter after welding. 5/8” will be approx. Yield Strength 50,000 psi min.
3/16” shorter after welding.
TRU‐WELD S Studs can be made in any length above the standard Elongation (% in 2 in.) 17% min.
minimum.
Elongation (% in 5x dia.) 14% min.
Material: Low carbon steel, ASTM A29, 1010‐1020. S Studs are also
available in weldable stainless steel. Type 302 is the most commonly Reduction of Area 50% min.
used. Other grades of stainless steel (except Type 303) are available
when required.

BASE CHUCK FOOT AND
FOOT PART # GRIP PART # FOOT PART # GRIP PART #
DIAMETER PART # GRIP #
3/8 CN‐025 B‐1N GN‐050 B‐1C GC‐050 QN‐050
7/16 CN‐031 B‐1N GN‐043 B‐1C GC‐043 QN‐044
1/2 CN‐037 B‐1C GN‐062 B‐2C GC‐062 QN‐062
5/8 CN‐050 B‐1C GN‐075 B‐2C GC‐075 QN‐075
3/4 CN‐062 B‐1C GN‐075 B‐2C GC‐075 QN‐075
7/8 CN‐075 B‐3N GN‐087 B‐3C GC‐087 QN‐087

CD STUD WELDING MATERIAL CAPABILITIES

STUD MATERIAL
BASE MATERIAL MILD STEEL; STAINLESS STEEL ALUMINUM BRASS
1010 - 1030 302/304/305 1100/5086/6061 70-30/65-35
MILD STEEL:
EXCELLENT EXCELLENT NA EXCELLENT
1006-1030
MEDIUM CARBON STEEL:
GOOD GOOD NA GOOD
1030-1050
GALVANIZED SHEET DUCT OR DECKING
EXCELLENT EXCELLENT NA NA
STRUCTURAL STEEL EXCELLENT EXCELLENT NA EXCELLENT
STAINLESS STEEL:
405,410,430, AND 300 SERIES (EXCL. 303)
LEAD-FREE BRASS, ELECTROLYTIC
COPPER, LEAD-FREE ROLLED COPPER
MOST ALUMINUM ALLOYS OF THE
NA NA EXCELLENT NA
1000,3000,5000, AND 6000 SERIES 1
DIE-CAST ZINC ALLOYS GOOD GOOD EXCELLENT GOOD

1) OTHER MATERIALS, SUCH AS 7000 SERIES ALUMINUM, TITANIUM ALLOYS, INCONEL, ETC. CAN BE WELDED UNDER SPECIFIED CONDITIONS.
2) GOOD – GENERALLY FULL STRENGTH RESULTS, DEPENDING ON THE COMBINATION OF STUD SIZE AND BASE METAL.
STANDARD LOAD CAPACITIES

MAX. FASTENING ULTIMATE TENSILE MAX. SHEAR LOAD
STUD MATERIAL STUD SIZE
TORQUE (INCH/LBS,) LOAD (LBS.) (LBS.)
6-32 6.0 500 375
LOW-CARBON 8-32 12.0 765 575
10-24 14.0 960 720
COPPER FLASHED 1/4-20 43.0 1,750 1,300
STEEL 5/16-18 72.0 2,900 2,200
3/8-16 106.0 4,300 3,250
6-32 10.0 790 590
8-32 20.0 1,260 940
10-24 23.0 1,530 1,150
STAINLES STEEL: 304 1/4-20 75.0 2,880 2,160
5/16-18 126.0 3,750 5,350
3/8-16 186.0 4,850 7,150
6-32 2.5 200 125
8-32 5.0 295 185
ALUMINUM ALLOY: 10-24 6.5 380 235
1100 1/4-20 21.5 670 415
5/16-18 36.0 1,125 695
3/8-16 53.0 1,660 1,000
6-32 3.5 375 235
8-32 7.5 585 365
ALUMINUM ALLOY: 10-24 10.0 735 460
5086 1/4-20 32.5 1,360 850
5/16-18 54.5 2,300 1,400
3/8-16 81.0 3,400 2,100
6-32 8.0 600 390
8-32 16.0 860 560
10-24 18.5 1,040 680
BRASS: 70-30, 65-35 1/4-20 61.0 1,950 1,275
5/16-18 102.0 3,280 2,140
3/8-16 150.0 4,800 3,160
*MAXIMUM FASTENING TORQUE SHOULD DEVELOP FASTENER TENSION TO SLIGHTLY LESS THAN YIELD POINT.


TYPE CD STUD
FULLY THREADED CAPACITOR DISCHARGE STUD – FLANGED
NO FERRULE NEEDED

WELD STUD SPECIFICATIONS
TD L TRU‐WELD FD
PART NUMBERING CODES (CD STUDS)

Diameter and Min. Length Part Number ST
PREFIX (I FOUR DIGITS OR CHARACTERS)
Flange Diameter
Thread Pitch before weld
#4-40 .250 CDEC‐004‐541 .187 CDEC = #4 CDKC= #10
CDGC = #6 CD04 = 1/4
#6-32 .250 CDGC‐004‐541 .218 CDIC = #8 CD05 = 5/16

#8-32 .250 CDIC‐004‐541 .250 SUFFIX (LAST THREE DIGITS)
#10-32 .250 CDKF‐004‐541 .250
FLANGE/NON‐FLANGE (5 OR 6)
#10-24 .250 CDKC‐004‐541 .250 TIP/NO TIP (4 OR 0)
1/4-20 .375 CD04‐006‐541 .312 MATERIAL (1, 2, 3)
1 – MILD STEEL
5/16-18 .500 CD05‐008‐541 .375 2 – STAINLESS STEEL
3/8-16 .500 CD06‐008‐541 .437 3 ‐ ALUMINUM
CD STUDS ARE AVAILABLE IN VARIOUS LENGTHS, DIAMETERS, AND MATERIALS
(TOO MANY TO LIST HERE)

MATERIAL
MILD STEEL, STAINLESS STEEL, ALUMINUM, BRASS
PLATING
ALL MILD STEEL STUDS ARE COPPER PLATING (NICKEL PLATING AVAILABLE UPON REQUEST
ANNEALING
ALL STUDS ARE ANNEALED WHERE REQUIRED

ESTIMATED WEIGHTS OF THREADED CD STUDS IN POUNDS PER 1000 PIECES
LENGTH #4‐40 #6‐32 #8‐32 #10‐24 1/4‐20 5/16‐18
1/4 .69 1.00 1.39 1.79 3.08 4.90
3/8 .94 1.38 1.93 2.50 4.37 6.98
1/2 1.18 1.76 2.49 3.21 5.66 9.06
5/8 1.43 2.13 3.04 3.93 6.95 11.13
3/4 1.67 2.51 3.60 4.64 8.24 13.21
7/8 1.92 2.89 4.15 5.35 9.52 15.29
1 2.16 3.26 4.71 6.07 10.81 17.36
1‐1/4 2.65 4.02 5.82 7.50 13.39 21.52
1‐1/2 3.15 4.77 6.93 8.92 15.96 25.67
1‐3/4 3.64 5.52 8.04 10.35 18.54 29.83


TYPE CD STUD
FULLY THREADED CAPACITOR DISCHARGE STUD – NON‐FLANGED
NO FERRULE NEEDED

WELD STUD SPECIFICATIONS PART NUMBERING CODES (CD STUDS)

TD L TRU‐WELD ND
ST
PREFIX (I FOUR DIGITS OR CHARACTERS)

Diameter and Min. Length Part Number Nominal Diameter CDEC = #4 CDKC= #10
Thread Pitch before weld
CDGC = #6 CD04 = 1/4
#4-40 .250 CDEC‐004‐641 .112 CDIC = #8 CD05 = 5/16

#6-32 .250 CDGC‐004‐641 .138 SUFFIX (LAST THREE DIGITS)
#8-32 .250 CDIC‐004‐641 .164
FLANGE/NON‐FLANGE (5 OR 6)
#10-32 .250 CDKF‐004‐641 .190 TIP/NO TIP (4 OR 0)
MATERIAL (1, 2, 3)
#10-24 .250 CDKC‐004‐641 .190 1 – MILD STEEL
1/4-20 .375 CD04‐006‐641 .250 2 – STAINLESS STEEL
3 ‐ ALUMINUM
5/16-18 .500 CD05‐008‐641 .312
3/8-16 .500 CD06‐008‐641 .375
CD STUDS ARE AVAILABLE IN VARIOUS LENGTHS, DIAMETERS, AND MATERIALS
(TOO MANY TO LIST HERE)

MATERIAL
MILD STEEL, STAINLESS STEEL, ALUMINUM, BRASS
PLATING
ALL MILD STEEL STUDS ARE COPPER PLATING (NICKEL PLATING AVAILABLE UPON REQUEST
ANNEALING
ALL STUDS ARE ANNEALED WHERE REQUIRED
ESTIMATED WEIGHTS OF THREADED CD STUDS IN POUNDS PER 1000 PIECES
LENGTH #4‐40 #6‐32 #8‐32 #10‐24 1/4‐20 5/16‐18

1/4 .69 1.00 1.39 1.79 3.08 4.90
3/8 .94 1.38 1.93 2.50 4.37 6.98
1/2 1.18 1.76 2.49 3.21 5.66 9.06
5/8 1.43 2.13 3.04 3.93 6.95 11.13
3/4 1.67 2.51 3.60 4.64 8.24 13.21
7/8 1.92 2.89 4.15 5.35 9.52 15.29
1 2.16 3.26 4.71 6.07 10.81 17.36
1‐1/4 2.65 4.02 5.82 7.50 13.39 21.52
1‐1/2 3.15 4.77 6.93 8.92 15.96 25.67
1‐3/4 3.64 5.52 8.04 10.35 18.54 29.83


Estimated Weights for Threaded CD Studs In Pounds Per 1000 Pieces
Length 4‐40 6‐32 8‐32 10‐24 1/4‐20 5/16‐18

1/4 .69 1.00 1.39 1.79 3.08 4.90
3/8 .94 1.38 1.93 2.50 4.37 6.98
1/2 1.18 1.76 2.49 3.21 5.66 9.06
5/8 1.43 2.13 3.04 3.93 6.95 11.13
3/4 1.67 2.51 3.60 4.64 8.24 13.21
7/8 1.92 2.89 4.15 5.35 9.52 15.29
1 2.16 3.26 4.71 6.07 10.81 17.36
1‐1/4 2.65 4.02 5.82 7.50 13.39 21.51
1‐1/2 3.15 4.77 6.93 8.92 15.96 25.67
1‐3/4 3.64 5.52 8.04 10.35 18.54 29.83
2 4.13 6.27 9.15 11.78 21.12 33.98
2‐1/4 4.62 7.03 10.26 13.21 23.69 38.14
2‐1/2 5.11 7.78 11.37 14.63 26.27 42.29
Estimated Weights of No Thread CD Studs in Pounds Per 1000 Pieces
Length 3/32 1/8 5/32 3/16 1/4 5/16

1/4 .68 1.06 1.59 2.24 3.87 5.97
3/8 .92 1.50 2.27 3.21 5.61 8.68
1/2 1.16 1.93 2.94 4.19 7.35 11.39
5/8 1.40 2.37 3.62 5.16 9.09 14.11
3/4 1.64 2.80 4.30 6.14 10.84 16.82
7/8 1.88 3.24 4.98 7.12 12.56 19.53
1 2.12 3.67 5.65 8.09 14.32 22.25
1‐1/4 2.60 4.54 7.01 10.04 17.81 27.67
1‐1/2 3.08 5.41 8.36 11.99 21.69 33.10
1‐3/4 3.56 6.28 9.72 13.95 24.78 38.52
2 4.04 7.15 11.07 15.90 28.25 43.95
2‐1/4 4.52 8.02 12.43 17.85 31.75 49.37
2‐1/2 5.00 8.89 13.78 19.80 35.23 54.80

6400 N. Honeytown Road (330) 669‐2773 Phone
Smithville, Ohio 44677 (330) 669‐2473 Fax
Heavy Duty Steel Fabrication Shop Stud Welding System
DESCRIPTION
The SC2400 is a fully integrated stud welding system with two digital controls for time and current. The system was designed to
meet the most challenging stud welding jobs.
Includes;
Power Supply Controller, TWE17000 Heavy Duty stud gun, 50 feet of 4/0 weld and control cable and 25 feet of 4/0 ground cable
FEATURES
Weld Range 1/4” ‐ 1” Diameter Consistent welding regardless of stud diameter.
Duty Cycle 1/4” Thru 5/8” ‐ Unlimited • Enhanced Duty Cycle for production requirements.

3/4” ‐ 18 to 24 per minute • Powerful output for even the largest diameter jobs.
7/8” ‐ 12 to 14 per minute • Stepless time and current control allow for infinite settings for fine‐
1” ‐ 6 to 8 per minute tuning the welding output.
• Safety welding interlock keeps system from double triggering and saves
on chuck wear.
• Stud Job Counter that can be reset for every job.
Dimensions Height 29” (736.6mm)
Width 28” (711.2mm)
Length 36” (914.4mm)
Weight 665 Lbs. (302kg)
Input 230 / 460 / 575 VAC 3 Phase 60Hz
Voltages
Fusing (Slow Acting) 230 / 180 Amps
Requirements 460 / 90 Amps
575 / 80 Amps
Heavy Duty Steel Fabrication Shop Stud Welding System
DESCRIPTION
meet the most challenging stud welding jobs, including thru‐deck applications (this also includes G90 decking).
Includes;
Power Supply Controller, TWE17000 Heavy Duty stud gun, 50 feet of 4/0 weld and control cable and 25 feet of 4/0 ground cable
FEATURES
Duty Cycle 1/4” Thru 5/8” ‐ Unlimited • Enhanced Duty Cycle for production requirements.

7/8” ‐ 12 to 14 per minute • Stepless time and current control allow for infinite settings for fine‐
1” ‐ 6 to 8 per minute tuning the welding output.
• Safety welding interlock keeps system from double triggering and saves
on chuck wear.

Width 28” (711.2mm)
Input 380 / 400 VAC 3 Phase 50Hz
Voltages
DESCRIPTION
meet the most challenging stud welding jobs, including thru‐deck applications (this also includes G90 decking).
Includes;
3000 Amp power supply, TWE17000 Heavy Duty stud gun, 50 feet of 4/0 weld and control cable and 25 feet of 4/0 ground cable.
FEATURES
Duty Cycle 1/4” Thru 5/8” ‐ unlimited • Smooth arc curve allows for the wide range of welding.

3/4” ‐ 22 to 24 per minute • Enhanced Duty Cycle for production requirements.
1” ‐ 12 to 14 per minute • Stepless time and current control allow for infinite settings for fine‐
tuning the welding output.
• Safety welding interlock keeps system from double triggering.
Width 29” (711.2mm)
Voltages 400 VAC 3 Phase 50Hz

575 / 90 Amps
DESCRIPTION
The SC3402 is fully‐integrated, dual‐gun, stud welding system with two digital controls for time and current. The system was de‐
signed to meet the most challenging stud welding jobs, including thru‐deck applications (this also includes G90 decking).
Includes;
3000 Amp power supply, two (2) TWE17000 heavy duty stud guns, two (2) cable sets of 50‐ft. of 4/0 weld and control cable, and two
(2) sets of 25‐ft. 4/0 ground cable.
FEATURES
Duty Cycle 1/4” Thru 5/8” ‐ unlimited • Smooth arc curve allows for the wide range of welding.
3/4” ‐ 22 to 24 per minute • Enhanced Duty Cycle for production requirements.
1” ‐ 12 to 14 per minute • Stepless time and current control allow for infinite settings for fine‐
tuning the welding output.
• Safety welding interlock keeps system from double triggering.

Width 29” (711.2mm)
Voltages 400 VAC 3 Phase 50Hz

460 / 100 Amps
575 / 90 Amps
Heavy Duty Steel Stud Welding System
The TRU‐WELD Diesel Generator is a fully‐integrated,
stud welding system that offers portability along with
your stud welding needs. This system incorporates a
SC3400 Heavy Duty Stud Welder with its own portable
power source, which enables you to finish jobs effec‐
tively and efficiently, without the costly task of discon‐
necting the power and moving the unit as the job re‐
quires.
SYSTEM FEATURES
• Aluminum weather enclosure • Auto‐Start control w/over‐speed
and over‐crank shut down
• Full sound attenuation
• Automatic low‐water shut down
• Critical Sound muffler
• Alternator w/Permanent Magnet
• Block engine heater
Generator and Automatic Voltage
• Battery charger Control
• Electronic governor • Two (2) 120 VAC outlets
SPECIFICATIONS SYSTEM INCLUDES;
Power 480 VAC, 3 Phase
• Mobile Generator
Amp Load Capacity 300 Amps
• SC3400 Heavy Duty Welder
Generator 256 KVA • TWE17000 Heavy Duty Stud Gun
Circuit Breaker 350 Amp (Main Line) • 25 ft. 4/0 ground cable w/clamp

• 50 ft. 4/0 starter combo cable
• 100 ft. 4/0 combo cable
HTTP://TruweldStudWelding.com
Smithville, OH 30043 (330) 669‐2473 Fax
DESCRIPTION
The TWE17000 has been designed to fit comfortably for all hands, including when wearing a work
glove. The neck of the handle has been tapered so that when grasped, the trigger can be accessed eas‐
ily, without any unnecessary strain. The handle length allows for better balance of the stud gun and it
keeps the welding cable and connector away from your hand, minimizing operator fatigue.
FEATURES
The TWE17000 is approximately 8.5” long from the weld cable to the back cap, and approximately 7”
long from the top of the stud gun to the bottom of the handle. The overall weight of the stud gun is ap‐
proximately 15 pounds ( with 8.5 feet of 4/0 weld cable and 8 feet of control cable (This also includes
all connectors, legs, and foot piece.).
The TWE17000 can be ordered to operate with any type of stud welding equipment. Simply specify the
make and model of your equipment and we will provide you with a stud gun connection that is com‐
patible with you unit, regardless of the manufacturer.
Order your TWE17000 Heavy Duty Stud Gun from your local TRU‐WELD Equipment Distributor.
Smithville, OH 44677 (330) 669‐2473 Fax
DESCRIPTION
The TWE18500 has been designed to fit comfortably for all hands, including when wearing a work
glove. The neck of the handle has been tapered so that when grasped, the trigger can be accessed eas‐
ily, without any unnecessary strain. The handle length allows for better balance of the stud gun and it
keeps the welding cable and connector away from your hand, minimizing operator fatigue.
FEATURES
The TWE18500 is approximately 6.5” long from the weld cable to the back cap, and approximately 7”
long from the top of the stud gun to the bottom of the handle. The overall weight of the stud gun is ap‐
proximately 11 pounds ( with 8.5 feet of 2/0 weld cable and 9 feet of control cable. This also includes
all connectors, legs, and foot piece.)
The TWE18500 can be ordered to operate with any type of stud welding equipment. Simply specify the
make and model of your equipment and we will provide you with a stud gun connection that is com‐
patible with you unit, regardless of the manufacturer.
Order your TWE18500 Medium Duty Stud Gun from your local TRU‐WELD Equipment Distributor.
Model: TWE‐250
Stud Welder Description
Incorporates the latest solid state technology into a
compact and rugged CD Stud Welder. This system has
the capacity to weld studs and pins (including cupped
head pins) ranging from 14‐guage through 1/4” full
flanged stainless steel studs.
SPECS TWE‐250 Operational and Safety Features

SIZE 15‐3/4” Length, 8” Width, 9” Height • LED Voltage Meter
WEIGHT 24 lbs.
• Safety Shutdown
WELD RANGE 14 gauge through 1/4” Stainless
• Cooling Fan
DUTY CYCLE 30 studs per minute (including 1/4”)
• Front‐Panel Informational LED’s
110 VAC @ 50/60Hz 10 Amp circuit or 220 VAC
PRIMARY POWER • Dial‐Down weld voltage control
@50/60Hz 5 Amp circuit
CHARGE VOLTAGE 35‐200 VDC
FEATURES
• Digital DC voltage readout on all models (allows for more accurate and repeatable weld settings).
• Cooling fan in all models for increased efficiency.
• Dial‐down DC voltage setting (no need to turn off the unit when resetting to a lower voltage).
• Only 10 amp circuit requirement (unit fused @ 10 amps).
• 33,000 micro farad capacitors charging to 200 VDC for greater power output @ lower DC voltage requirements.
• Terminal connections on the capacitors are over 5/8” in diameter for a good seat of the terminal buss bars to increase reliability.
• The terminal connections on the capacitors have 1/4‐28 socket set screws inserted into each one. The socket set screw is used to make the
connection to the buss bar. This eliminates damaging the threads in the aluminum connectors of the capacitor, ensuring a solid connection.
• Rigid internal construction connecting the entire internal unit to the front and rear panels minimizes the opportunity of the components
coming loose during handling or operations.
• Sheet metal is powder‐coated for greater durability, texture, and appearance.
• Stud Guns are ergonomically designed for better hand fit and comfort (reduces operator fatigue for increased weld repeatability).
• Stud Guns have a permanent internal spring with easy adjustment for various spring pressures allowing an increased opportunity to apply
the correct spring pressure to the weld (no need for a variety of different springs for various applications).
• Stud Guns can be configured for “B” Collets, “CI” Collets, Euro Collets or standard tapered chucks.
• The TWE CD Unit weighs less than most other available models for ease or carrying.
Model: TWE‐321

WEIGHT 29 lbs.
• Safety Shutdown
• Cooling Fan
FEATURES
Model: TWE‐375

WEIGHT 34 lbs.
• Safety Shutdown
• Cooling Fan
FEATURES
Model: TWP‐1
Pin Welder Description
Incorporates the latest solid state technology into
a compact and rugged, portable CD Pin Welder.
This system has the capacity to weld pins
(including cupped head pins) up to 10‐gauge .
SPECS TWE‐PIN WELDER Operational and Safety Features

10 5/8” x 9 11/16” x 6 7/8” (270 mm x 246 mm x
SIZE • LED Voltage Meter
174 mm)
WEIGHT 10.6 lbs. • Safety Shutdown
WELD RANGE Up to 10 gauge • Cooling Fan
DUTY CYCLE 24 pins per minute • Front‐Panel Informational LED’s
FEATURES
• Digital DC voltage readout (allows for more accurate and repeatable weld settings).
• Cooling fan for increased efficiency.
• 33,000 micro farad single capacitor charging to 130VDC for greater power output @ lower DC voltage requirements.
• Terminal connections on the capacitor are over 5/8” in diameter for a good seat of the terminal buss bars to increase reliability.
• The terminal connections on the capacitor have 1/4‐28 socket set screws inserted into each one. The socket set screw is used to make the
• The TWE‐Pin Welder is equipped in a rugged outer case for greater durability, texture, and appearance.
• The TWE‐Pin Welder weighs less than most other available models for ease or carrying.

Texas Stud Weld Accessories Catalog

Uploaded by

Copyright:

Available Formats

Texas Stud Weld Accessories Catalog

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Texas Stud Weld Accessories Catalog

Uploaded by

Copyright:

Available Formats

FERRULE GRIPS

7/16 SMALL .585 GD‐043 13.00

STUD DIA. PART NO. PRICE

1/8 X 1” CR‐CE 94.00

CH‐087‐1 SLEEVE ONLY 36.00

ANCHOR SIZE PART NO. PRICE

PART NO. DESCRIPTION PRICE

PART NO. STUD DIA. PRICE

B-1N B-2N B-3N

B-6N/B-7N B-4N/B-5N 028-833

GUN TYPE STUD SIZE PART NO. PRICE

B-1C B-2C B-3C

B-6C/B-7C B-4C/B5C B-4CR/B-5CR

GUN TYPE STUD SIZE PART NO. PRICE

1/4 MB‐025 .500 .875 11.00

PART NO. BG‐1 PART NO. BG‐2 PART NO. BG‐3

#10 CDB‐018A 14.00 1-3/16

STUD SIZE PART NO. NELSON # PRICE

STUD LENGTH PART NO. PRICE

1/4 DIA 3/8 DIA

PART NO. DESCRIPTION PRICE

PART NO. DESCRIPTION PRICE PART NO. DESCRIPTION PRICE

107‐0007‐MF HI TEMP PIN 1.90 (FITS (M) OR (F) )

PART NO. DESCRIPTION PRICE

PART NO. DESCRIPTION PRICE

NELSON 2‐WIRE (M) PANEL MOUNT PROWELD HUBBELL (M)

PART NO. DESCRIPTION PRICE

PART NO. DESCRIPTION PRICE

PART NO. DESCRIPTION PRICE

PART NO. DESCRIPTION PRICE

Estimated Weights for Threaded Studs In Pounds Per 1000 Pieces

Length 1/4” 5/16” 3/8” 7/16” 1/2” 5/8” 3/4” 7/8”

Estimated Weights of No Thread Studs in Pounds Per 1000 Pieces

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com

CHUCK FOOT GRIP FERRULE FOOT PLATE Reduction of Area 50% min. 50% min.

WELD STUD SPECIFICATIONS WELD STUD PACKAGING WELD STUD WEIGHTS

D L TRU‐WELD Pieces Boxes Pieces

Elongation (% in 5x dia.) 14% min. 15% min.

Elongation (% in 2 in.) 17% min. 20% min.

Elongation (% in 5x dia.) 14% min. 15% min.

D L TRU‐WELD Pieces Boxes Pieces

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com

Elongation (% in 5x dia.) 14% min. 15% min.

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com

Elongation (% in 5x dia.) 14% min. 15% min.

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com

WELD STUD SPECIFICATIONS WELD STUD PACKAGING WELD STUD WEIGHTS

D L TRU‐WELD Pieces Boxes Pieces

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com

WELD STUD SPECIFICATIONS WELD STUD PACKAGING WELD STUD WEIGHTS

D L TRU‐WELD Pieces Boxes Pieces

TFP Corporation/TRU‐WELD (330) 725‐7741 http://www.tfpcorp.com

FOOT Type “C” Studs are cold‐worked deformed steel bars

D L TRU‐WELD HD HT FD FH

3/8 3-7/16 PSR06‐055‐11 1.190 .260 1/2 1/8

1/2 2-5/8 PSR08‐042‐11 1.580 .330 11/16 5/32

5/8 3-3/4 PSR08‐060‐11 1.980 .400 7/8 3/16

3/4 4-3/8 PSR08‐070‐11 2.370 .470 1-1/16 1/4