Scribd Logo
Upload

Welcome to Scribd!

  • 88 views

    Bsa RD Finderscope

    Uploaded by

    Justin
    Your finderscope is powered by one 3V "coin style" lithium battery. The battery will provide many hours of service. When the dot fails to light, or becomes dim, the battery should be replaced.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Bsa RD Finderscope

    Uploaded by

    Justin
    88 views1 page
    Your finderscope is powered by one 3V "coin style" lithium battery. The battery will provide many hours of service. When the dot fails to light, or becomes dim, the battery should be replaced.

    Original Title

    bsa_rd_finderscope

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Your finderscope is powered by one 3V "coin style" lithium battery. The battery will provide many hours of service. When the dot fails to light, or becomes dim, the battery should be replaced.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    88 views1 page

    Bsa RD Finderscope

    Uploaded by

    Justin
    Your finderscope is powered by one 3V "coin style" lithium battery. The battery will provide many hours of service. When the dot fails to light, or becomes dim, the battery should be replaced.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    INSTRUCTION SHEET FOR ELECTRONIC RED DOT

    FINDERSCOPE
    ALIGNMENT:
    1) Activate the illuminated red dot by sliding the power switch (A) forward (Fig. 1).
    2) Turn the power of the spotting scope to its lowest setting.
    3) Direct the spotting scope so that a distinct object
    in the distance is directly in the center of the field FIG. 1
    of view.
    4) Adjust the finderscope until the red dot appears
    superimposed over the center of the same object.
    Left/right adjustment is obtained by turning knob
    “B” Up/down adjustment is obtained by turning
    knob “E” (Fig. 1). The illuminated red dot
    finderscope is marked “UP” and “R” right. However,
    as the device was originally intended for use on an
    airman, these indications are opposite from what
    must be done when used with your spotting scope.
    That is to say, you must rotate the left/right knob in
    an anti-clockwise fashion to move the dot in a right FIG. 2 FIG. 3
    hand direction. And, rotate the “UP” knob a
    clockwise fashion to move the dot up.

    INSTALLING BATTERIES:
    Your finderscope is powered by one 3V “coin style”
    lithium battery. This battery will provide many hours of
    service. When the dot fails to light, or becomes dim,
    the battery should be replaced. To replace the battery,
    the finderscope must be removed from the spotting
    scope and the replacement affected as follows:
    1) Loosen and remove the 2 mounting screws (D).
    2) Remove the finderscope from the base. (Fig. 2)
    3) Remove the battery cap (C).
    4) Remove the old battery by using a screwdriver or
    similar implement. (Fig. 3)
    5) Inset the new battery + side down.
    6) Reverse steps 4 through 1 to reassemble and reinstall the finderscope.

    BSA Optics, Inc. • 3911 SW 47th Avenue • Suite 914 • Fort Lauderdale, Florida 33314 • Tel: (954) 581-2144 • Fax: (954) 581-3165
    e-mail: [email protected] • website: www.bsaoptics.com
    ©2002 BSA OPTICS, INC. • MADE IN CHINA

    You might also like