Scribd
Upload
642 views1 page

Mosfet As AC Switch

This document discusses several key considerations for using power MOSFETs in AC switch applications: 1) Placing two power MOSFETs source to source prevents their intrinsic body diodes from conducting during each half cycle of the AC signal. This allows the majority of current to flow through the bidirectional MOSFET channels. 2) Care must be taken not to exceed the maximum gate-to-source voltage rating, as this can puncture the silicon oxide layer. Transients can also couple high voltages through the drain-gate capacitance. 3) The body diodes can be used as freewheeling diodes for inductive loads, reducing component count and costs, despite their higher forward voltage

Uploaded by

duppal35
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
642 views1 page

Mosfet As AC Switch

This document discusses several key considerations for using power MOSFETs in AC switch applications: 1) Placing two power MOSFETs source to source prevents their intrinsic body diodes from conducting during each half cycle of the AC signal. This allows the majority of current to flow through the bidirectional MOSFET channels. 2) Care must be taken not to exceed the maximum gate-to-source voltage rating, as this can puncture the silicon oxide layer. Transients can also couple high voltages through the drain-gate capacitance. 3) The body diodes can be used as freewheeling diodes for inductive loads, reducing component count and costs, despite their higher forward voltage

Uploaded by

duppal35
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

USING POWER TRANSISTORS IN AC SWITCH APPLICATIONS

Power MOSFETs have an anti-parallel body diode which will


conduct for every negative cycle of AC signal. BY placing two
power MOSFETs source to source, the intrinsic body diodes will
prevent each other from conducting. If voltage across MOSFET
channel is less than Vf of body diode, then majority of current
will flow through the MOSFET channel instead of body diode.
Note: MOSFET channel is bidirectional switch.
The silicon oxide layer between the gate and the source regions can be punctured by exceeding its
dielectric strength. Care should be exercised not to exceed the gate-to-source maximum voltage
rating. Even if the applied gate voltage is kept below the maximum rated gate voltage, the stray
inductance of the gate connection, coupled with the gate capacitance, may generate ringing
voltages that could lead to the destruction of the oxide layer.
Over voltages can also be coupled through the drain-gate selfcapacitance due to transients in the drain circuit.
Body diodes may be utilized as freewheeling diodes for inductive
loads. While these diodes usually have rather high forward
voltage drop, they can handle large currents and are sufficient in
many applications, reducing part count, and thus, device cost and
board space.
Extra:
Zeners are frequently used to protect the gate from transients.
Unfortunately they also contribute to oscillations and have been
known to cause device failures. A transient can get to the gate from the drive side or from the drain
side. In either case, it would be an indication of a more fundamental problem: a high impedance
drive circuit. A zener would compound this problem, rather than solving it. Sometimes a zener is
added to reduce the ringing generated by the leakage of a gate drive transformer, in combination
with the input capacitance of the MOSFET. If this is necessary, it is advisable to insert a small series
resistor (5-10 Ohms) between the zener and the gate, to prevent oscillations.
Impedance of Gate Circuit
To turn on a power MOSFET a certain charge has to be supplied to the gate to raise it to the desired
voltage, whether in the linear region or in the saturation region. The best way to achieve this is by
means of a voltage source, capable of supplying any amount of current in the shortest possible time.
If the device is operated as a switch, a large transient current capability of the drive circuit reduces
the time spent in the linear region, thereby reducing the switching losses.
On the other hand, if the device is operated in the linear mode, a large current from the gate drive
circuit minimizes the relevance of the Miller effect, improving the bandwidth of the stage and
reducing the harmonic distortion.
MOS-gated transistors should be driven from low impedance voltage sources, not only to reduce
switching losses, but to avoid dv/dt induced turn-on and reduce the susceptibility to noise.

You might also like