Steelmaster 120sb 120 Min

Technical Data Sheet
15400
acrylic
15400
VValidationDate).
Steelmaster 120SB
Product description
This is a one component solvent based acrylic thin film intumescent coating. Independently approved for fire
protection of structural steel exposed to cellulosic fire. Can be used as mid coat or finish coat in atmospheric
environments. Suitable on approved primers on carbon steel and galvanised steel substrates.
Typical use
Specially designed as passive fire protection for steel constructions. Suitable for structural steel to be exposed to
a wide range of corrosive environments up to high as a part of a complete system.
Other
Approvals and certificates

BS 476 (90, 120 minutes)
Additional certificates and approvals may be available on request.
Colours
grey, white
Product data
Property
Test/Standard
Solids by volume
Flash point
VOC-Solvent Emission Directive
ISO 3233
ISO 3679 Method 1
SED (1999/13/EC)
Description
72 2 %
25 C
262 g/kg
The provided data is typical for factory produced products, subject to slight variation depending on colour.
Recommended film thickness per coat

Film thickness and
spreading rate
Dry film thickness

(m)
(m)
Theoretical
spreading rate
(m/l)
Wet film thickness
Minimum
200
280
3,6
Maximum
Typical
1400
700
1950
970
0,5
1
Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.
Date of issue:
1 August 2014
by Jotun Group
Page: 1/4
This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

Steelmaster 120SB
Surface preparation summary table

Surface preparation
Substrate
Minimum
Coated surfaces
Recommended
Clean, dry and undamaged

compatible coating (ISO 12944-4 6.
1)
Clean, dry and undamaged

compatible coating (ISO 12944-4 6.
1)
Application
Application methods
The product can be applied by
Spray:
Use airless spray.
Brush:
Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Product mixing ratio (by volume)

Single pack
Thinner/Cleaning solvent
Do not add thinner. The product is ready for use.
Cleaning solvent:
Jotun Thinner No. 7
Guiding data for airless spray

Nozzle tip (inch/1000):
19-27
Pressure at nozzle (minimum):
250 bar/3300 psi
Drying and Curing time

Substrate temperature
5 C
10 C
Surface (touch) dry

Walk-on-dry
Dried to over coat, minimum
2h
48 h
24 h
1h
24 h
8h
23 C
40 C
30 min 20 min
16 h
8h
4h
2h
Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and
within the DFT range of the product.
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will
be affected correspondingly. All drying times have been measured at a dry film thickness of 700 m.
Date of issue:
1 August 2014
by Jotun Group
Page: 2/4


Steelmaster 120SB
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the
surface.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
As per approved primer/topcoat list.
Packaging (typical)
Steelmaster 120SB
Volume
(litres)
Size of containers
(litres)
5/20
5/20
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Shelf life at 23 C
Steelmaster 120SB
18 month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Health and safety
Date of issue:
1 August 2014
by Jotun Group
Page: 3/4


Steelmaster 120SB
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Colour variation
Products primarily meant for use as primers and antifoulings may have slight color variations from batch to
batch. Such products may fade and chalk when exposed to sunlight and weathering.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Date of issue:
1 August 2014
by Jotun Group
Page: 4/4


Steelmaster 120sb 120 Min

Uploaded by

Copyright:

Available Formats

Steelmaster 120sb 120 Min

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Steelmaster 120sb 120 Min

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

Approvals and certificates

Recommended film thickness per coat

Dry film thickness

Wet film thickness

This Technical Data Sheet supersedes those previously issued.

Technical Data Sheet

Surface preparation summary table

Clean, dry and undamaged

Clean, dry and undamaged

Use airless spray.

Product mixing ratio (by volume)

Jotun Thinner No. 7

Guiding data for airless spray

Pressure at nozzle (minimum):

250 bar/3300 psi

Drying and Curing time

Surface (touch) dry

This Technical Data Sheet supersedes those previously issued.

Technical Data Sheet

Health and safety

This Technical Data Sheet supersedes those previously issued.

Technical Data Sheet

This Technical Data Sheet supersedes those previously issued.

You might also like