3101799-EN R1.0 EST3X User Guide PDF

EST3X User Guide
P/N 3101799-EN REV 1.0 ISS 10MAY11
Copyright
2011 UTC Fire & Security. All rights reserved.
Trademarks and
patents
The EST3X name and EST logo are trademarks of

UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
Edwards, A Division of UTC Fire & Security

Americas Corporation, Inc.
8985 Town Center Parkway, Bradenton, FL 34202, USA
Version
This document applies to EST3X control panels with firmware

version 1.0.
FCC compliance
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Contact information
For contact information, see www.utcfireandsecurity.com.
Content
Important information iii
Fire alarm system limitations vi
Intended audience vii
Chapter 1
Introduction 1
System overview 2
System hardware capabilities 2
Overview of operator controls and indicators 4
System operation 8
Event messages 9
User access levels 10
Using the rotary controller 11
Using the paging microphone 13
Chapter 2
Basic operating instructions 15

Checking for active points 16
Finding detectors that may need servicing 17
Viewing history reports 18
Finding firmware and database version numbers 18
Viewing the alarm count 19
Determining panel TCP/IP settings 19
Determining if your 3-MODCOM is NFPA 72 compliant 20
Silencing the panel buzzer 20
Silencing alarm signals 21
Acknowledging events 22
Resetting the fire alarm system 22
Performing a lamp test 22
Activating alarm signals manually 23
Changing the LCD screen language 23
Chapter 3
Advanced operating instructions 25

Changing detector alarm sensitivity 26
Changing event message routes 26
Disabling and enabling devices 27
Disabling and enabling zone groups 28
Setting the system time and date 29
Using a TCP/IP connection to write to the panel 29
Using a TCP/IP connection to read from the panel 30
Guard patrol routes 32
EST3X User Guide
Bypassing the photo element on SIGA2-PHS smoke

detectors 33
Testing a carbon monoxide (CO) detector 34
Chapter 4
Preventive maintenance and testing 37

Introduction 38
Service provider information 38
Visual inspection schedule 38
Troubleshooting 41
Appendix A
System addressing 43
Address formats 44
Card address 44
Hardware layer device addresses 46
Operator layer device address 47
Remote annunciator device addresses 49
Glossary 57
Index 59
ii
EST3X User Guide
Important information
Limitation of liability
To the maximum extent permitted by applicable law, in no event will UTCFS be
liable for any lost profits or business opportunities, loss of use, business
interruption, loss of data, or any other indirect, special, incidental, or
consequential damages under any theory of liability, whether based in contract,
tort, negligence, product liability, or otherwise. Because some jurisdictions do not
allow the exclusion or limitation of liability for consequential or incidental
damages the preceding limitation may not apply to you. In any event the total
liability of UTCFS shall not exceed the purchase price of the product. The
forgoing limitation will apply to the maximum extent permitted by applicable law,
regardless of whether UTCFS has been advised of the possibility of such
damages and regardless of whether any remedy fails of its essential purpose.
Installation in accordance with this manual, applicable codes, and the instructions
of the authority having jurisdiction is mandatory.
While every precaution has been taken during the preparation of this manual to
ensure the accuracy of its contents, UTCFS assumes no responsibility for errors
or omissions.
EST3X FCC compliance

This equipment can generate and radiate radio frequency energy. If the
equipment is not installed in accordance with this manual, it may cause
interference to radio communications. This equipment has been tested and found
to comply with the limits for Class A computing devices pursuant to Subpart B of
Part 15 of the FCC Rules. These rules are designed to provide reasonable
protection against such interference when this equipment is operated in a
commercial environment. Operation of this equipment is likely to cause
interference, in which case the user, at his own expense, will be required to take
whatever measures may be required to correct the interference.
3-MODCOM FCC compliance

Cautions
To ensure proper operation, this dialer must be installed according to the

enclosed installation instructions. To verify that the dialer is operating properly
and can successfully report an alarm, it must be tested immediately after
EST3X User Guide
iii
installation, and periodically thereafter, according to the enclosed test

instructions.
In order for the dialer to be able to seize the phone line to report an alarm or
other event when other customer equipment (telephone, answering system,
computer modem, etc.) connected to the same line is in use, the dialer must
be connected to a properly installed RJ-31X jack. The RJ-31X jack must be
connected in series with, and ahead of, all other equipment attached to the
same phone line. Series installation of an RJ-31X jack is depicted in the
wiring diagram. If you have any questions concerning these instructions, you
should consult your telephone company or a qualified installer.
Testing
When programming emergency numbers or making test calls to emergency
numbers, remain on the line and briefly explain to the dispatcher the reason for
the call. Perform programming and testing activities in the off-peak hours, such
as early morning or late evenings.
Compliance
For equipment approved before July 23, 2001: This dialer complies with
Part 68 of the FCC rules. A label attached to the dialer contains, among other
information, the FCC registration number and ringer equivalence number
(REN) for this equipment. If requested, this information must be provided to
the telephone company.
For equipment approved after July 23, 2001: This dialer complies with Part
68 of the FCC rules and the requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). A label attached to the dialer
contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this information must be provided to the
telephone company.
The plug and jack used to connect the dialer to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by ACTA. The dialer must be connected to a compliant
RJ-31X or RJ-38X jack using a compliant cord. If a modular telephone cord is
supplied with the dialer, it is designed to meet these requirements. See
installation instructions for details.
A ringer equivalence number (REN) is used to determine how many devices

you can connect to a telephone line. If the total REN value for all devices
connected on a telephone line exceeds that allowed by the telephone
company, the devices may not ring on an incoming call. In most (but not all)
areas the total REN value should not exceed 5.0. To be certain of the total
REN value allowed on a telephone line, contact the local telephone company.
iv
EST3X User Guide
For products approved after July 23, 2001, the REN is part of the product
identifier in the format US:AAAEQ##TXXXX. The digits ## represent the REN
without a decimal point. Example: 03 is an REN of 0.3. For earlier products
the REN is listed separately.
If the dialer is harming the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be
required. If advance notice isnt practical, the telephone company will notify
you as soon as possible. You will also be advised of your right to file a
complaint with the FCC, if you believe it is necessary.
The telephone company may make changes to its facilities, equipment,

operations, or procedures that could affect the operation of the dialer. If this
happens, the telephone company will provide advance notice in order for you
to make necessary modifications to maintain uninterrupted service.
If you are experiencing problems with the dialer, contact the manufacturer for
repair or warranty information. If the dialer is harming the telephone network,
the telephone company may request that you disconnect the dialer until the
problem is resolved.
The dialer contains no user serviceable parts. In case of defects, return the
dialer for repair.
You may not connect the dialer to a public coin phone or a party line service
provided by the telephone company.
3-MODCOM Industry Canada information

Note: The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective,
operational, and safety requirements. Industry Canada does not guarantee the
equipment will operate to the users satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations made
by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user disconnect the
equipment.
EST3X User Guide
Caution: Users should not attempt to make connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as
appropriate.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines, and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly
important in rural areas.
Note: The Load Number (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which is used by
the device, to prevent overloading. The termination on a loop may consist of any
combination of devices subject only to the requirements that the sum of the Load
Numbers of all the devices does not exceed 100.
Advisory messages
Advisory messages alert you to conditions or practices that can cause unwanted
results. The advisory messages used in this document are shown and described
below.
WARNING: Warning messages advise you of hazards that could result in injury
or loss of life. They tell you which actions to take or to avoid in order to prevent
the injury or loss of life.
Caution: Caution messages advise you of possible equipment damage. They tell
you which actions to take or to avoid in order to prevent the damage.
Note: Note messages advise you of the possible loss of time or effort. They
describe how to avoid the loss. Notes are also used to point out important
information that you should read.
Fire alarm system limitations

The purpose of an automatic fire alarm system is to provide early detection and
warning of a developing fire. There are a number of uncontrollable factors that
can prevent or severely limit the ability of an automatic fire alarm system to
provide adequate protection. As such, an automatic fire alarm system cannot
guarantee against loss of life or loss of property.
vi
EST3X User Guide
Two main causes of system failures are improper installation and poor
maintenance. The best way to minimize these types of system failures is to have
only trained fire alarm system professionals design, install, test, and maintain
your fire alarm system in accordance with national and local fire codes.
Fire alarm systems will not operate without electrical power. As fires frequently
cause power interruption, we suggest that you discuss ways to safeguard the
electrical system with your local fire protection specialist.
In the event your EST3X control panel needs servicing, please contact your
system service provider as soon as possible. Refer to Service provider
information on page 38 for their name and contact information.
Intended audience
The intent of this document is to provide the EST3X life safety system owner with
control panel operating instructions. You may assume that your site-specific
software has been installed and that the final overall system testing has been
completed prior to you using this guide. The extent of your use with panel
buttons, indicators, and menus is dependant upon your access privileges.
EST3X User Guide
vii
viii
EST3X User Guide
Chapter 1
Introduction
Summary
This chapter provides information about your EST3X control panel to give you a
basic understanding of its operation.
Content
System overview 2
System hardware capabilities 2
Overview of operator controls and indicators 4
System operation 8
Event messages 9
User access levels 9
Using the rotary controller 11
Using the paging microphone 13
EST3X User Guide
Chapter 1: Introduction
System overview
The EST3X control panel can operate as a stand-alone panel, as part of a
64-node EST3X life safety network, or as part of a 64-node EST3 life safety
network. The EST3X control panel is listed for the following types of service:
Commercial protected premises fire alarm control unit
Smoke control system
Releasing device control unit
Emergency communication and relocation
The EST3X control panel is also listed for use as a burglary annunciator when
connected to an EST3 life safety system that includes security features.
The EST3X user interface includes indicators and operator controls that allow
you to respond quickly in emergency situations. The EST3X user interface gives
you the ability to view message details and system reports, and to enable and
disable devices and groups. With the correct access level passwords, you can
activate and restore sensitivity settings and message routing, test system
devices, and other tasks.
System hardware capabilities

The EST3X control panel, in its basic configuration, supports up to:
250 addressable devices
Four Class B notification appliance or auxiliary power output circuits
30 remote or graphic annunciators for a total of 30 sets of common controls,

3,840 LED indicators, and 1,920 switches
Two RS-232 ports (one RJ-11 modular jack for panel programming and
diagnostics and one terminal block connection for connecting accessory
devices)
With the proper hardware options, you can expand the EST3X control panel to
support:
1,250 additional addressable devices (1,500 total)
24 Class B initiating device circuits
12 additional Class B notification appliance circuits (16 total)
Four Class A notification appliance or auxiliary power output circuits
EST3X User Guide
Three reverse polarity outputs
Three control-display modules for a total of 72 local LED indicators and 36

local switches
Two dialer outputs
One Ethernet connection for panel programming and diagnostics
Live voice and prerecorded audio messaging
Connection to an EST3X or EST3 life safety network using copper, fiber

optics, or both (maximum network size may not exceed 64 nodes)
EST3X User Guide
Overview of controls and indicators

Figure 1: 4X-LCD User Interface
1. Alarm LED
11. Alarm Silence button and LED
2. Disable LED
12. Rotary controller
3. SUP (Supervisory) LED
13. Display
4. GND Fault LED
14. Normal display screen (see Figure 2)
5. CPU Fail LED
15. Off -normal display screen

(see Figure 3)
6. Trouble LED
7. Power LED
8. Panel Silence button and LED
9. Reset button and LED
10. Acknowledge button and LED
EST3X User Guide
Figure 2: Normal screen
1. Time
2. Date
3. Custom banner message
4. Number of times the panel has
gone into alarm
Figure 3: Off-normal screen

1. Time
2. Date
3. Number of active points
4. Number of disabled points
5. Selected event message
6. Contents of selected event
message queue. In this example,
the Alarm message queue.
7. Most recent highest priority event
message
8. Monitor queue with the number of
active monitor event messages
9. Trouble queue with the number of
active trouble event messages
10. Supervisory queue with the
number of active supervisory
event messages
11. Alarm queue with the number of
active alarm event messages
EST3X User Guide
Figure 4: 3X-PMI Paging Microphone Interface
1. Push-to-talk button
5. All Call button and LED
2. Paging Microphone
6. Page to Evac button and LED
3. Paging volume indicator (indicates the

sound level of the person speaking into the
microphone)
7. All Call Minus button and LED

8. Page to Alert button and LED
4. Ready to page LED
EST3X User Guide
Figure 5: RLCD-C and RLCD Remote Annunciator

RLCD-C
14
15
13
12
11
Power
Fire Alarm
Supervisory
Ground Fault
Trouble
Controls Enabled
10
Ack/Silence
Reset
Signal Silence
Drill
Lamp Test
RLCD
6
14
15
13
12
11
Power
Fire Alarm
Supervisory
Ground Fault
Trouble
Controls Enabled
10
Ack/Silence
Lamp Test
1.
2.
3.
4.
5.
6.
7.
8.
Display
Up button
Down button
Enter button
Lamp Test button and LED
Drill button and LED
Signal Silence button and LED
Reset button and LED
EST3X User Guide
9.
10.
11.
12.
13.
14.
15.
Ack/Silence button and LED

Controls Enabled LED
Trouble LED
Ground Fault LED
Supervisory LED
Fire Alarm LED
Power LED
Figure 6: RLED-C Remote Annunciator

2
Power
Fire Alarm
Supervisory
Ground Fault
Trouble
Controls Enabled
Ack/Silence
12
Reset
Signal Silence
Drill
Lamp Test
11
1.
2.
3.
4.
5.
6.
Power LED
Fire Alarm LED
Supervisory LED
Ground Fault LED
Trouble LED
Controls Enabled LED
7.
8.
9.
10.
11.
12.
10
Ack/Silence button and LED

Reset button and LED
Signal Silence button and LED
Drill button and LED
Lamp Test button and LED
Programmable LEDs
System operation
The basic function of the EST3X control panel is to monitor status changes in the
life safety system and to activate outputs according to the site-specific software.
Status change signals, also called events, are classified as follows:
Alarm (highest priority): Events that signal fire alarms or other life-threatening
emergencies
Supervisory: Events that signal off-normal conditions with sprinkler and

extinguishing systems and other equipment related to property safety
Trouble: Events that signal faults within the system
Monitor (lowest priority): Events that signal the operation of ancillary

equipment
EST3X User Guide
During normal operation (no events), the EST3X control panel displays the
Normal screen (see Figure 2). When the automatic fire detection system signals
a status change, the EST3X control panel:
Posts the event message for the point that activated the event into the
appropriate event message queue and displays the off-normal screen (see
Figure 3)
Turns on the corresponding system status LED
Turns on the panel buzzer to the pattern for the highest priority active event
Displays the most recent, highest priority event message (see Figure 3)
Activates common relays and programmed outputs
Event messages
The EST3X control panel uses event messages to identify points that signal a
status change. The first line of the event message displays the event number and
the event name. The second line displays the message text. The message text is
either the address of the point that activated the event or, if programmed, a
location description.
Event messages are stored in queues. There is one queue for each type of event
message (see Figure 3).
The EST3X control panel automatically displays the content of the highest priority
event message queue, except when you are viewing event messages in another
queue. If you are viewing event messages in one queue when a higher priority
event message is placed in another queue, the EST3X control panel continues to
display the content of the current queue until the user timeout period expires or
until you select the other queue.
To view an event message in the current queue:
1. Turn the rotary controller to select the event message. The selected event
message appears in the highlighted area at the top of the display.
To view an event message in another queue:
1. Click the rotary controller to display the Queue Menu.
2. Click the event message queue from the list of options.
3. Turn the rotary controller to select the event message.
EST3X User Guide
To get details about an event message:

1. Select the event message.
2. Click the rotary controller to display the Queue Menu.
3. Click Details.
User access levels

The EST3X control panel uses access levels to prevent unauthorized users from
operating certain controls and menu commands. Access levels 1 to 4 require a
password. Access level 0 does not. Table 1 lists the operator controls and menu
commands available for each access level.
Once you have entered an access level password you do not have to enter it
again for any operator control or menu command with the same access level or
lower unless the user timeout period expires. After that, you are required to enter
the access level password again. The user timeout period is typically set for 5
minutes.
See your project documentation for the access level passwords programmed for
your system.
Table 1: User access level privileges
User access level
Privileges
Level 0
(No password required)
Acknowledge function (button)
Alarm silence function (button) [1]
Panel silence function (button) [1]
Reset function (button) [1]
Event details
Statuses
Reports
Drill function (activate/restore)
Output selection
Display/printer selection
Printer selection
Toggle language
Level 1
All level 0 privileges, plus:
10
Guard patrol routes (activate/restore)
EST3X User Guide
User access level
Privileges
Level 2
All level 0 and level 1 privileges, plus:
Devices (enable/disable)
Zone groups (enable/disable)
Remote read lock (activate/restore)
Remote write unlock (activate/restore)
Sensor bypass (activate/restore)
Gas accel response (activate/restore)
Alternate sensitivity (activate)
Alternate message route (activate)
Primary sensitivity (restore)
Primary message route (restore)
Change time (program)
Change date (program)
Security devices (bypass/remove bypass)
Security partitions (arm/disarm)
Change password for level 1 (program)
[1] May be programmed to require an access level password. See your project documentation for
details.
Using the rotary controller

The EST3X rotary controller performs the functions of a computer keyboard and
the Enter key. Turning the rotary controller allows you to scroll through event
messages on the LCD screen, menus and lists, and numbers for panel, card, and
device addressing. Pressing (clicking) the rotary controller allows you to access
event message details, menus, and selection screens and to enter address
numbers and backspaces.
Selecting menus and commands

Press the rotary controller to access the first menu, from which you will access
other menus. For all menus, turn the dial to scroll to a desired selection. Press
the dial to click the selection.
EST3X User Guide
11
Returning to the event message screen or previous

screen
Pressing the rotary controller while in certain screens returns you to the event
message screen or to the previous screen.
Note: Pressing the Acknowledge button also returns you to the event message
screen or to the previous screen.
Returning to the previous screen from an address field

In an address field, you can return to the previous screen from the first number in
the field by turning the rotary controller to the < character and then pressing the
dial.
For example, in the address field below you are positioned at the first number. If
you click the < character you will return to the previous screen.
ENTER DEVICE
<PCCDDDD
Entering a panel, card, or device address

To enter a panel, card, or device address, turn the rotary controller clockwise or
counterclockwise to scroll to the desired number (0-9), and then press it to enter
the number. Pressing the rotary controller automatically moves the cursor to the
next number position.
Note: You do not have to enter a panel number except when you want to enter
the panel, card, or device address for a remote EST3X control panel. See your
project documentation for a list of panel numbers.
Backspacing
In an address field, you can backspace to a previous number by turning the
rotary controller to scroll to the < character and then pressing the dial. You can
then enter the number.
In the address example below, you will be able to change the number 3.
ENTER DEVICE
0103<DDDD
12
EST3X User Guide
Using the paging microphone

The 3X-PMI Paging Microphone Interface (see Figure 4) gives emergency
responders the ability to broadcast instructions to occupants throughout the
protected premises. There are four types of page you can make:
All Call: Broadcasts live voice messages throughout the facility
Page to Evac: Broadcasts live voice messages only to areas receiving

evacuation signals
Page to Alert: Broadcasts live voice messages only to areas receiving alert
signals
All Call Minus: Broadcasts live voice messages only to areas that are not
receiving evacuation signals or alert signals
To make an announcement using the paging microphone:

1. Select the area to receive the page by pressing the appropriate page function
button. The buttons LED indicates when the system is ready for you to
speak.
2. Press the PTT button on the microphone. The Ready to Page LED flashes
while the preannouncement tone is sounding.
3. Begin speaking once the Ready to Page LED is on steady. Adjust your voice
level so that the Paging Volume indicator only flickers occasionally in the
middle. Avoid speaking so loud that the Paging Volume indicator lights all the
way to the right.
4. When you are finished speaking, release the PTT button, and then press the
page function button again to cancel the page and return the system to its
previous condition.
Note: The system automatically cancels the page and returns to its previous
condition after a short delay if you do not cancel the page manually.
EST3X User Guide
13
14
EST3X User Guide
Chapter 2
Basic operating
instructions
Summary
This chapter provides instructions for operating the basic features of your EST3X
life safety system. Basic features are those that anyone can operate. Typically,
basic features do not require passwords.
Content
Checking for active points 16
Finding detectors that may need servicing 17
Viewing an event history report 18
Finding firmware and database version numbers 18
Viewing the alarm history 19
Determining the panel TCP/IP settings 19
Determining if your 3-MODCOM is NFPA 72 compliant 20
Silencing the panel buzzer 20
Silencing alarm signals 21
Acknowledging events 22
Resetting the fire alarm system 22
Performing a lamp test 22
Activating alarm signals manually 23
Changing the display screen language 23
EST3X User Guide
15
Chapter 2: Basic operating instructions
Checking for active points

The EST3X control panel provides the following status reports to help you find
out if any points in the system are in an active or other off-normal state:
All Active Points: Lists all points that are in an active or other off-normal state
(trouble, disable, etc.)
Alarm: Lists all alarm points that are in the active state
Supervisory: Lists all supervisory points that are in the active state
Trouble: Lists all points that are in the trouble state
Monitor: Lists all monitor points that are in the active state
Test: Lists all points in an active service group that are in the active or trouble
state
Disabled Points: Lists all points that are in the disabled state
Outputs: Lists all output points that are in the active state (audibles, visibles,
panel LEDs)
To check for active points:

1. Access the Main menu, and then click Status.
2. Click one of the reports described above.
3. Enter the panel address (PP).
4. Click Display and scroll through the report.
or
Click Print Locally.
5. When finished, click the rotary controller or press the Acknowledge button to
exit the report.
16
EST3X User Guide
Finding detectors that may need servicing

The EST3X control panel provides the following maintenance reports to help you
find out if any addressable smoke detectors need servicing:
Dirty Devices > 80%: Lists all addressable smoke detectors that have a
%Dirty value of greater than 80%. Smoke detectors that are more than 80%
dirty should be cleaned or replaced as soon as possible.
Note: The %Dirty value is an indication of a smoke detectors ability to
compensate for dust and dirt buildup inside the chamber. Smoke detectors
with higher %Dirty values are less able to compensate.
Dirty Devices > 20%: Lists all addressable smoke detectors that have a
%Dirty value greater than 20%. A smoke detector that is more than 20% dirty
should be noted for possible cleaning or replacing.
Single Device: Lists the %Dirty value for a single smoke detector. The report
also includes the smoke detectors model type, primary and alternate alarm
sensitivity values, and, if programmed, a location description. To view this
report you must know the device address of the smoke detector.
Devices on a Card: Lists the %Dirty value for all of the smoke detectors on a
signaling line circuit. The report also includes each smoke detectors model
type, primary and alternate alarm sensitivity values, and, if programmed, a
location description. To view this report you must know the panel number,
card number, and loop number of the signaling line circuit.
To find detectors that may need servicing:

1. Access the Main Menu, click Reports, and then click Device Maintenance.
3. Enter the device address (PPCCDDDD), or the loop address (PPCCL).
or
exit the report.
EST3X User Guide
17
Viewing history reports

The EST3X control panel provides the following history reports for determining
when the last 1,100 events and operator commands were activated or restored:
History with Text: Provides a history of events and operator commands

logged by the panel. For each point that activated or restored, the detail
includes the points message text.
History without Text: Provides a history of events and operator commands

logged by the system. For each point that activated or restored, the detail
includes the points device address.
To view a history report:

1. Access the Main Menu, click Reports, and then click History.
or
exit the report.
Finding firmware and database version

numbers
By viewing a Revisions report, you can find the version numbers for the following:
The CPU firmware
The project database and the SDU used to compile and download the project
database
The audio database, if equipped with a paging microphone
The application code (firmware), bootloader code, and database for each card
installed in the panel
To view the Revisions report:

1. Access the Main Menu, click Reports, and then click Revisions.
18
EST3X User Guide

or
exit the report.
Viewing the alarm count

The EST3X control panel records how many times it went into the alarm
condition. During normal operation, the alarm count is displayed on the LCD.
When the EST3X user interface displays the off-normal screen, you must run a
Revisions report to see the alarm count.
To view the alarm count:
3. Click Display and scroll through the report. The alarm count is on the second
line of the report.
or
exit the report.
Determining panel TCP/IP settings

If your panel is equipped with an Ethernet (TCP/IP) connection, you may be
asked to provide the IP address, subnet mask, and gateway settings.
To determine the panel TCP/IP settings:
3. Click Display and scroll through the report. The settings are at the bottom of
the report.
or
EST3X User Guide
19
exit the report.
Determining if your 3-MODCOM is NFPA 72

compliant
A MODCOM compliance report tells you if the 3-MODCOM installed in the panel
meets NFPA 72 configuration requirements. The report does not indicate why the
3-MODCOM may be noncompliant.
To view the MODCOM Compliance report:
1. Access the Main Menu, click Reports, and then click Modcom Compliance.
or
exit the report.
Silencing the panel buzzer

The EST3X control panel sounds the panel buzzer when an event message is
posted into one of the event message queues. Pressing the Panel Silence button
or acknowledging the event message silences the buzzer. The panel buzzer
automatically re-sounds when a new event message is posted or when the panel
trouble re-sound timer expires (typically after 24 hours).
Notes
The panel buzzer may be configured to sound periodically to remind you that
the panel has been silenced.
For nonlatching events, the panel buzzer automatically silences when the
event is restored.
Pressing the Panel Silence button also silences the buzzer on remote
annunciators, provided that the remote annunciators are communicating.
20
EST3X User Guide
To silence the panel buzzer:

1. Press the Panel Silence button or acknowledge the event message.
2. If prompted, enter the access level password.
Silencing alarm signals

WARNING: Death or serious injury. The protected premises may be occupied.
Do not silence alarm signals or reset the control panel unless you are authorized
to do so and only after all occupants have been evacuated.
Pressing the Alarm Silence button silences all audible alarm signals and, if
configured, all visible alarm signals. Pressing the Alarm Silence button does not
silence alarm signals under the following conditions:
When a waterflow alarm switch is active and the system is configured to

prevent silencing alarm signals activated by a waterflow alarm switch
When the system is configured to delay the silencing of alarm signals, in

which case the Alarm Silence button may be inoperable for up to three
minutes following an alarm event
Silenced alarm signals automatically turn back on when:
The Alarm Silence button is pressed a second time
Another alarm input activates
Another alarm input in the same zone activates, unless the system is
configured to prevent it
To silence alarm signals:

1. Press the Alarm Silence button.
Acknowledging events
Acknowledging an event confirms that you have seen the event message. When
you acknowledge an event, the EST3X control panel places a check mark and
the word Acknowledged next to the event. On proprietary systems, you cannot
silence the panel until all events have been acknowledged.
EST3X User Guide
21
To acknowledge an event:
1. Press the Acknowledge button.
Resetting the fire alarm system

WARNING: Death or serious injury. The protected premises may be occupied.
Do not reset the fire alarm system until the proper authorities have determined
that the threat of fire is no longer present.
Pressing the Reset button restores the fire alarm system to its normal state
provided that all latched inputs have been restored. If alarm signal initiating
devices have not been restored, active alarm signals remain active and silenced
alarm signals remain silenced.
Notes
System programming may render the Reset button inoperable for up to three
minutes following an alarm event.
Resetting the system does not enable disabled points or restore outputs
activated by a switch.
To reset the fire alarm system:

1. Press the Reset button.
Performing a lamp test

Use the Lamp Test command on the Test Menu to verify the operation of the
LCD and LED indicators. The lamp test command temporarily turns on the panel
buzzer, all LED indicators, and every pixel on the LCD. The lamp test command
only operates the indicators on the panel from which the command is initiated.
To perform a lamp test:
1. Access the Main Menu, click Test, and then click Lamp Test.
22
EST3X User Guide
Activating alarm signals manually

The EST3X drill feature lets you activate alarm signals manually without putting
the panel into alarm. When you activate a drill, all audible alarm signals turn on
and, if configured, all visible alarm signals turn on, but other automatic fire alarm
responses are not activated. The alarm signals remain active until the drill is
canceled.
To activate a drill:
1. Access the Main Menu, click Activate, and then click Drill.
To cancel a drill:
1. Press the Alarm Silence button.
or
Access the Main Menu, click Restore, and then click Drill.
Changing the LCD screen language

Use the Toggle Language command on the Program Menu to toggle the LCD
screen text to a secondary language.
Note: The panel must be configured for a secondary language.
To change the LCD screen language:
1. Access the Main Menu, and then click Program.
2. Click Toggle Language.
EST3X User Guide
23
24
EST3X User Guide
Chapter 3
Advanced operating
instructions
Summary
This chapter provides instructions for operating the advanced features of your
EST3X life safety system. Advanced features alter system operation and require
the access level 2 password or greater.
Content
Changing detector alarm sensitivity 26
Changing event message routes 26
Disabling and enabling devices 27
Disabling and enabling zone groups 28
Setting the system time and date 29
Using a TCP/IP connection to write to the panel 29
Using a TCP/IP connection to read from the panel 30
Guard patrol routes 32
Activating a guard patrol route 32
Restoring a guard patrol 32
Bypassing the photo element on SIGA2-PHS smoke detectors 33
Testing a carbon monoxide (CO) detector 34
EST3X User Guide
25
Chapter 3: Advanced operating instructions
Changing detector alarm sensitivity

Your fire alarm system can be programmed with two different alarm sensitivity
settings. The alarm sensitivity setting determines how easily automatic fire
detectors can sense a fire alarm condition. Typically, the primary alarm sensitivity
setting is programmed for daytime operation and the alternate alarm sensitivity
setting is programmed for nighttime and weekend operation.
To activate the alternate alarm sensitivity settings:
1. Access the Main Menu, and then click Activate.
2. Click Alt Sensitivity.
3. Enter the access level password.
To restore the primary alarm sensitivity settings:
1. Access the Main Menu, and then click Restore.
2. Click Primary Sensitivity.
Changing event message routes

Your fire alarm system can be programmed with a primary message route and an
alternate message route. The message route setting determines where event
messages are displayed. Typically, the primary message route is programmed
for daytime operation and the alternate message route is programmed for
nighttime and weekend operation.
In most applications, a time control is used to automatically switch event
messages over to their alternate route setting. When the time control is restored,
event messages are automatically switched back to their primary route settings.
To activate alternate message routing:
2. Click Alt Message Route.
26
EST3X User Guide
To restore primary message routing:

2. Click Primary Msg Route.
Disabling and enabling devices

Disabling a device prevents the EST3X control panel from processing status
change signals from the device, or changing the output state of the device, until
the device is enabled. For example, the EST3X control panel does not generate
an alarm active event when you activate a disabled detector, but will do so after
the detector is enabled.
The EST3X control panel keeps track of how many times you disable and enable
a device. You must enable a device the same number of times you disable it in
order to return the device to its initial condition.
Device addresses are listed in Appendix A System addressing on page 43.
Notes
You cannot disable a device configured as a common alarm output.
Disabling the device address for the dialer or a dialer account deletes all
event messages sent to that account before they are transmitted. The dialer
still transmits the accounts test-abnormal message and any message that
was in the dialer queue before the account was disabled.
Disabling all of the devices in a zone group automatically disables the zone
group. Enabling any device in the zone group automatically enables the zone
group.
To disable a device:
1. Access the Main Menu, and then click Disable.
2. Click Device, and then enter the device address (PPCCDDDD).
To enable a device:
1. Access the Main Menu, and then click Enable.
2. Click Device, and then enter the device address (PPCCDDDD).
EST3X User Guide
27
Disabling and enabling zone groups

Disabling a zone group prevents the EST3X control panel from processing status
change signals from every device in the zone group until the zone group is
enabled. For example, the EST3X control panel does not generate an alarm
active event when you activate a detector in a disabled zone group, but will do so
after the zone group is enabled.
The EST3X control panel keeps track of how many times you disable and enable
a zone group. You must enable a zone group the same number of times you
disable it in order to return the zone group to its initial condition.
Notes
The control panel tracks events from a disabled zone group but does not
process them until the zone group is enabled.
If you disabled the zone group by disabling all of the devices in the zone
group, enabling the zone group enables all of the devices in the zone group.
To disable a zone group:

1. Access the Main Menu, and then click Disable.
2. Click Group, and then select Zone Group.
3. Scroll through the list and click the desired zone group.
To enable a zone group:
1. Access the Main Menu, and then click Enable.
2. Click Group, and then select Zone Group.
3. Scroll through the list and click the desired zone group.
Setting the system time and date

The EST3X control panel incorporates a system clock to time stamp events and
to activate time controls. The time is presented in 24-hour format. The date is
presented in month-day-year format.
To set the time:
1. Access the Main Menu, click Program, and then click Change Time.
28
EST3X User Guide

3. Enter the hour, minutes, and seconds (HHMMSS).
Examples:
000000 = midnight
010000 = 1:00 a.m.
120000 = noon
130000 = 1:00 p.m.
235900 = 11:59 p.m.
To set the date:
1. Access the Main Menu click Program, and then click Change Date.
3. Enter the date (MMDDYYYY).
Using a TCP/IP connection to write to the

panel
If your EST3X control panel is equipped with an Ethernet card, your service
provider can use the TCP/IP connection to write (download) the project database
to the panel instead of using an RS-232 connection. By default, this feature is
locked to prevent someone from changing the project database without
permission. You cannot write to the panel until it is unlocked.
Notes
Activating and restoring the Remote Write Unlock command does not affect
downloading the project database using an RS-232 connection.
The Remote Write Unlock command times out after 15 minutes.
This function should only be used by the installer or service provider.

Changes to the fire alarm system must be tested and may require local
authority approval.
To allow writing to the panel:

2. Click Remote Write Unlock.
3. Click By Panel, and then enter the panel address (PP).
or
Click All Panels.
EST3X User Guide
29

To prevent writing to the panel:
2. Click Remote Write Unlock.
or
Click All Panels.
Using a TCP/IP connection to read from the

panel
If your EST3X control panel is equipped with an Ethernet card, your service
provider can use the TCP/IP connection to read status and diagnostic information
from the panel instead of using an RS-232 connection. By default, this feature is
unlocked. Locking this feature prevents you from reading from the panel until it
is unlocked.
Notes
The Remote Read Lock command does not automatically time out.
Activating and restoring the Remote Read Lock command does not affect
reading panel status and diagnostic information using an RS-232 connection.
To prevent reading from the panel:

2. Click Remote Read Lock.
or
Click All Panels.
To allow reading from the panel:
2. Click Remote Read Lock.
30
EST3X User Guide
3. Click By panel, and then enter the panel address (PP).

or
Click All Panels.
Guard patrol routes

The guard patrol feature allows you to monitor the activities of security guards.
Guards are required to walk any one of a number of predetermined routes called
tours. During each tour, the guard must activate guard patrol stations that are
strategically located along the route. Should a guard activate a station too early,
too late, or out of sequence, an active guard patrol event message shows on the
LCD screen. When a guard patrol alarm is generated, you must restore the guard
patrol route to clear the alarm.
Activating a guard patrol route

Activating a guard patrol route starts the systems early, late, and out of
sequence sensing mechanisms. If a station reports in early, late, or out of
sequence, the guard patrol sensing mechanisms stop and the tour is ended.
To activate a guard patrol route:
2. Click Guard Patrol Route, and then click the route to be activated.
Note: A guard patrol route is activated automatically when you activate the first
guard patrol station on the route.
Restoring a guard patrol

When a guard patrol tour ends because a guard patrol station was not activated
at the proper time, you must restore the guard patrol group to which the station
belonged.
EST3X User Guide
31
To restore a guard patrol:

2. Click Guard Patrol Route, and then click the route to be restored.
Bypassing the photo element on SIGA2-PHS

smoke detectors
If your fire alarm system is equipped with SIGA2-PHS combination photo-heat
detectors, you can temporarily bypass the photo element and use only the heat
element to detect a fire.
Notes
The Sensor Bypass command works only with SIGA2-PHS detectors whose
Primary Operation is set for "Photo is Supervisory | Heat is AlarmHeat."
Bypassing the photo element activates a Sensor Bypass Active trouble

event.
If the photo element activates while it is bypassed, a Disabled Active Event

is recorded in the event history.
To bypass the photo element on a SIGA2-PHS:

2. Click Sensor Bypass, and then enter the device address (PPCCDDDD).
To unbypass the photo element on a SIGA2-PHS:
2. Click Sensor Bypass, and then enter the device address (PPCCDDDD).
Testing a carbon monoxide (CO) detector

SIGA2 carbon monoxide (CO) detectors have an accelerated response mode
that you can use when testing. In normal mode, SIGA2 CO detectors activate
after carbon monoxide levels reach 400 ppm (parts per million) for 4 minutes. In
32
EST3X User Guide
accelerated response mode, SIGA2 CO detectors activate within 4 to 8 seconds

after reaching 400 ppm.
Notes
The SIGA2 CO detector normal response rate mimics the normal absorption
rate of CO in the bloodstream.
If you do not restore the response mode, CO detection returns to its normal
response time after 4 hours.
To change the CO rate of detection:

2. Click Gas Accel Response, and then enter the device address (PPCCDDDD).
To restore the CO rate of detection:
2. Click Gas Accel Response, and then enter the device address (PPCCDDDD).
EST3X User Guide
33
34
EST3X User Guide
Chapter 4
Preventive maintenance
and testing
Summary
This chapter provides instructions for maintaining and testing your EST3X life
safety system.
Content
Introduction 38
Service provider information 38
Visual inspection schedule 38
Routine maintenance schedule 40
Troubleshooting 41
EST3X User Guide
35
Chapter 4: Preventive maintenance and testing
Introduction
Periodic visual inspections and maintenance testing must be performed on your
EST3X life safety system to ensure that it is operating correctly and as required
by the local authority having jurisdiction (AHJ). Maintenance testing is performed
by your service provider or a qualified technician with a complete understanding
of the system hardware and functions.
Visual inspection and maintenance schedules are provided in this section, as
well as a form to document your service providers contact information.
Service provider information

Fill in the contact information of your service provider on the form below. If more
than one service provider is assigned, use the additional form.
EST3X Service Provider
Name
Address
City
State
Country
Postal code
Telephone
E-mail
Fax
EST3X Service Provider

Name
Address
City
State
Country
Postal code
Telephone
E-mail
Fax
36
EST3X User Guide
Visual inspection schedule

Perform visual inspections in accordance with Table 2 below or more often if
required by the local AHJ.
Table 2: Visual inspection schedule
Component
Frequency
Recommended procedure
Radiant energy fire detectors Monthly

(heat detectors)
Inspect the equipment for any visible signs of

damage or other changes that may adversely
affect performance. Clean if necessary.
Supervisory signal devices
Monthly
Verify that the modules green LED flashes.

Ensure that there are no changes that may
adversely affect equipment performance.
Waterflow devices
Monthly

Batteries
Semiannually
Inspect batteries for corrosion or leakage. Verify

that the battery connections are tight and secure.
Clean the connections, if required. Replace
batteries every 5 years, or sooner if conditions
warrant.
Control unit trouble signals
Semiannually

Emergency voice/alarm
communication equipment
Semiannually

affect performance.
Remote annunciators
Semiannually

affect performance.
Duct detectors
Semiannually

affect performance.
Electromechanical releasing
devices
Semiannually

Fire extinguishing systems or Semiannually

suppression systems

Fire alarm boxes
Semiannually

affect performance.
Heat detectors
Semiannually

EST3X User Guide
37
Component
Frequency
Recommended procedure
Smoke detectors
Semiannually

Guard tour equipment
Semiannually

affect performance.
Interface equipment
Semiannually

affect performance.
Alarm notification appliances
Semiannually

Supervising station fire alarm Semiannually

system transmitters

Control unit
Annually

affect performance.
Fiber optic cable connections Annually
Inspect the cables for any visible signs of

damage, loose connections, or other changes
that may adversely affect performance
Routine maintenance schedule

Routine maintenance and testing should be scheduled for your EST3X life safety
system in accordance with Table 3 below or more often if required by the local
AHJ.
Note: Only your system service provider or a qualified technician with a complete
understanding of the system hardware and functions should perform system
maintenance and tests.
Table 3: Routine maintenance schedule
Component
Frequency
Control equipment [1]
Quarterly /
Annually
Supervisory signal devices (except valve tamper switches)
Quarterly
Off-premises transmission equipment
Quarterly
Waterflow devices
Semiannually
Valve tamper switches
Semiannually
Batteries [2]
Annually
38
EST3X User Guide
Component
Frequency
Control unit trouble signals
Annually
Fiber optic cable connections
Annually
Emergency voice/alarm communication equipment
Annually
Remote annunciators
Annually
Smoke detectors
Annually
Heat detectors
Annually
Fire alarm boxes
Annually
Fire extinguishing systems or suppression systems
Annually
Guard tour equipment
Annually
Interface equipment
Annually
Audible notification appliances
Annually
Textual audible notification appliances (speakers)
Annually
Visible notification appliances
Annually
Supervising station fire alarm system transmitters
Annually
[1] Test control equipment quarterly when it is not connected to a supervising station.
[2] Replace batteries every five years, or sooner if conditions warrant.
Troubleshooting
Problems with your EST3X life safety system can generally be classified in two
categories: application programming problems and hardware (including firmware)
problems. Many times hardware problems are identified by the system itself.
Application programming problems are typically suspected when an incorrect
response happens, or when a response fails to happen or happens at the wrong
time.
Only your system service provider or a qualified technician with a complete
understanding of the system hardware and functions should perform system
servicing and repairs. Refer to Service provider information on page 38 for their
contact information. Refer to the EST3X Technical Reference Manual
(P/N 3101888-EN) for detailed troubleshooting information.
Before contacting your service provider, make note of the following:
Messages shown on the LCD screen

Construction in the area that may have caused the problem
Adverse weather that may have caused the problem
Damage to any equipment
EST3X User Guide
39
40
EST3X User Guide
Appendix A
System addressing
Summary
This appendix provides an easy way to look up card and device addresses.
Content
Address formats 44
Card address 44
Hardware layer device addresses 46
Operator layer device address 47
Remote annunciator device addresses 49
EST3X User Guide
41
Appendix A: System addressing
Address formats
EST3X addresses are in PPCCDDDD format, where:
PP is the cabinet number. Possible values are: 01 (single panel systems) or

01 to 64 (networked systems).
CC is the cards logical address. Possible values are listed in Table 4.
DDDD is the device number. Possible values are listed in Table 5, Table 6,
and Table 7.
Card address
Cards have a physical address and a logical address. The physical address
identifies the cards location in the panel. The logical address identifies the card
in the CPU database. See Table 4 below and Figure 7 on page 45.
Table 4: EST3X card numbering
Card or circuit
Logical address
SFS1-CPU Main Board
00
4X-LCD User Interface
32
PS10-4B Power Supply
02
Signature loop controller on the SFS1-CPU Main Board
03
Remote annunciator interface on the SFS1-CPU Main Board
04
Option card installed in Card Slot 4
05
06
07
3X-PMI Paging Microphone Interface
08
Display module connected to the option card installed

in Card Slot 4
37

in Card Slot 5
38

in Card Slot 6
39
42
EST3X User Guide
Figure 7: Logical addresses for an EST3X control panel
PP00
PP02
PP03
PP05
B
B
+
LOOP1
S
H
A
A
+
LOOP1
SP
MW
PR
1
B
B
+
LOOP1
PP06
N/C
B
B
+
LOOP1
S
H
A
A
+
LOOP1
SP
MW
PR
1
B
B
+
LOOP1
PP07
N/C
B
B
+
LOOP1
TB1
TB1
TB1
J1
J1
J1
TB2
N/C
PP08
PP04
B
B
+
LOOP2
SP
MW
PR
A
A
+
LOOP2
S
H
B
B
+
LOOP2
PP37
S
H
A
A
+
LOOP1
SP
MW
PR
1
B
B
+
LOOP1
TB2
N/C
B
B
+
LOOP2
SP
MW
PR
A
A
+
LOOP2
S
H
PP38
B
B
+
LOOP2
N/C
TB2
N/C
B
B
+
LOOP2
SP
MW
PR
A
A
+
LOOP2
S
H
B
B
+
LOOP2
PP39
Paging Microphone
Paging
Volume
Ready
To Page
All Call
All Call
Minus
EST3X User Guide
Page
To Evac
Page
To Alert
43
Hardware layer device addresses

Table 5 below lists the device addresses for points on the EST3X hardware
layer.
Table 5: EST3X hardware layer device addresses
Card
Device or circuit
Address
PS10-4B
NAC/AUX 1
NAC/AUX 2
NAC/AUX 3
NAC/AUX 4
PP020001
PP020002
PP020003
PP020004
Detectors
Modules
Detectors
Modules
PP030001 to PP030125
PP030126 to PP030250
PP030251 to PP030375
PP030376 to PP030500
3-IDC8/4
IDC/NAC 1
IDC/NAC 2
IDC 3
IDC 4
IDC/NAC 5
IDC/NAC 6
IDC 7
IDC 8
PPCC0001
PPCC0002
PPCC0003
PPCC0004
PPCC0005
PPCC0006
PPCC0007
PPCC0008
3-SSDC1
Detectors
Modules
PPCC0001 to PPCC0125
Detectors
Modules
Detectors
Modules
3-AADC1
Detectors
Modules
3-ZA20(A/B)
Amplifier output
NAC output
PPCC0000
PPCC0001
3-ZA40(A/B)
Amplifier output
NAC output
PPCC0000
PPCC0001
3X-PMI
Default_Normal_PP_08
Default_Alert_PP_08
Default_Evac_PP_08
Default_Pre_PP_08
MSG_005 to MSG_255
PP080001
PP080002
PP080003
PP080004
PP080005 to PP080255
SFS1-CPU
Loop Circuit 1
Loop Circuit 2
3-SDDC1
Loop Circuit 1
Loop Circuit 2
44
EST3X User Guide
Operator layer device address

Table 6 below lists the device addresses for points on the EST3X operator layer.
See also Figure 8 on page 48.
Table 6: EST3X operator layer device addresses
Module type
LED or switch
Address
12SW/12LED
SW01 to SW12
LED01 to LED12
12SW/24LED
SW01 to SW12
LED01 to LED24
24LED
LED01 to LED24
3SW/3LED6
SW01 to SW18
LEDs
3SW/4LED4
SW01 to SW12
LED01
LED02
LED03
LED04
LED05
LED06
LED07
LED08
LED09
LED10
LED11
LED12
LED13
LED14
LED15
LED16
PPCC0129
PPCC0131
PPCC0132
PPCC0133
PPCC0135
PPCC0137
PPCC0138
PPCC0139
PPCC0141
PPCC0143
PPCC0144
PPCC0145
PPCC0147
PPCC0149
PPCC0150
PPCC0151
EST3X User Guide
45
Figure 8: Operator layer LED and switch numbering
12SW/12LED
12SW/24LED
LED01
SW01
LED01
SW01
LED12
SW12
LED24
SW12
3SW/3LED6
46
24LED
LED01
LED24
3SW/4LED4
LED01
SW01
LED18
SW18
LED01
SW01
LED16
SW12
EST3X User Guide
Remote annunciator device addresses

Table 7 on page 52 lists the device addresses for LEDs and switches on RLED-C
remote annunciators, RLED24 expanders, GCI graphic annunciator cards, and
GCIX expander cards. See also Figure 9, Figure 10, and Figure 11.
Figure 9: RLED-C LED numbering
LED01
LED17
LED16
LED32
Power
Fire Alarm
Supervisory
Ground Fault
Trouble
Controls Enabled
Ack/Silence
RLED-C
Reset
Signal Silence
Drill
Lamp Test
LED01
LED17
LED33
LED16
LED32
LED48
RLED24
EST3X User Guide
47
Figure 10: GCI card LED and switch numbering

LED01
LED02
LED03
LED04
LED05
LED06
LED07
LED08
ACK/Panel Silence SW
Reset SW
Signal Silence SW
Drill SW
Lamp Test SW
Supervisory LED
Fire Alarm LED
Power LED
Lamp Test LED
ACK/Panel Silence LED
Enable Controls LED
Trouble LED
Ground Fault LED
Drill LED
Signal Silence LED
Reset LED
NOT USED
NOT USED
NOT USED
SW01
SW02
SW03
SW04
NOT
USED
J1
J2
J3
J7
EXT SW
SW1
J15
GCI
J4
1
LED09
LED10
LED11
LED12
LED13
LED14
LED15
LED16
LED17
LED18
LED19
LED20
LED21
LED22
LED23
LED24
48
J5
1
J6
1
J8
1
SW16
SW15
SW14
SW13
SW12
SW11
SW10
SW09
SW08
SW07
SW06
SW05
LED32
LED31
LED30
LED29
LED28
LED27
LED26
LED25
EST3X User Guide
Figure 11: GCIX card LED and switch numbering

LED17
LED18
LED19
LED20
LED21
LED22
LED23
LED24
SW01
SW02
SW03
SW04
SW05
LED16
LED15
LED14
LED13
LED12
LED11
LED10
LED09
LED08
LED07
LED06
LED05
LED04
LED03
LED02
LED01
SW06
SW07
SW08
SW09
SW10
SW11
SW12
J1
J2
J3
J7
GCIX
J4
1
LED25
LED26
LED27
LED28
LED29
LED30
LED31
LED32
LED33
LED34
LED35
LED36
LED37
LED38
LED39
LED40
EST3X User Guide
J5
1
J6
1
J8
1
SW24
SW23
SW22
SW21
SW20
SW19
SW18
SW17
SW16
SW15
SW14
SW13
LED48
LED47
LED46
LED45
LED44
LED43
LED42
LED41
49
Table 7: Remote annunciator device addresses

No.
Annunciator
LED or switch
Address
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP040201 to PP040232
PP020249 to PP040264
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP040301 to PP040348
PP040349 to PP040372
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP040401 to PP040448
PP040449 to PP040472
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP040501 to PP040532
PP020549 to PP040564
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP040601 to PP040648
PP040649 to PP040672
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP040701 to PP040748
PP040749 to PP040772
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP040801 to PP040832
PP020849 to PP040864
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP040901 to PP040948
PP040949 to PP040972
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP041001 to PP041048
PP041049 to PP041072
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP041101 to PP041132
PP021149 to PP041164
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP041201 to PP041248
PP041249 to PP041272
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP041301 to PP041348
PP041349 to PP041372
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP041401 to PP041432
PP021449 to PP041464
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP041501 to PP041548
PP041549 to PP041572
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP041601 to PP041648
PP041649 to PP041672
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP041701 to PP041732
PP021749 to PP041764
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP041801 to PP041848
PP041849 to PP041872
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP041901 to PP041948
PP041949 to PP041972
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP042001 to PP042032
PP022049 to PP042064
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP042101 to PP042148
PP042149 to PP042172
50
EST3X User Guide
No.
10
11
12
13
14
Annunciator
LED or switch
Address
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP042201 to PP042248
PP042249 to PP042272
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP042301 to PP042332
PP022349 to PP042364
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP042401 to PP042448
PP042449 to PP042472
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP042501 to PP042548
PP042549 to PP042572
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP042601 to PP042632
PP022649 to PP042664
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP042701 to PP042748
PP042749 to PP042772
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP042801 to PP042848
PP042849 to PP042872
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP042901 to PP042932
PP022949 to PP042964
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP043001 to PP043048
PP043049 to PP043072
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP043101 to PP043148
PP043149 to PP043172
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP043201 to PP043232
PP043249 to PP043264
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP043301 to PP043348
PP043349 to PP043372
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP043401 to PP043448
PP043449 to PP043472
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP043501 to PP043532
PP043549 to PP043564
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP043601 to PP043648
PP043649 to PP043672
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP043701 to PP043748
PP043749 to PP043772
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP043801 to PP043832
PP043849 to PP043864
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP043901 to PP043948
PP043949 to PP043972
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP044001 to PP044048
PP044049 to PP044072
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP044101 to PP044132
PP044149 to PP044164
EST3X User Guide
51
No.
15
16
17
18
19
20
52
Annunciator
LED or switch
Address
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP044201 to PP044248
PP044249 to PP044272
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP044301 to PP044348
PP044349 to PP044372
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP044401 to PP044432
PP044449 to PP044464
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP044501 to PP044548
PP044549 to PP044572
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP044601 to PP044648
PP044649 to PP044672
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP044701 to PP044732
PP044749 to PP044764
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP044801 to PP044848
PP044849 to PP044872
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP044901 to PP044948
PP044949 to PP044972
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP045001 to PP045032
PP045049 to PP045064
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP045101 to PP045148
PP045149 to PP045172
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP045201 to PP045248
PP045249 to PP045272
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP045301 to PP045332
PP045349 to PP045364
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP045401 to PP045448
PP045449 to PP045472
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP045501 to PP045548
PP045549 to PP045572
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP045601 to PP045632
PP045649 to PP045664
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP045701 to PP045748
PP045749 to PP045772
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP045801 to PP045848
PP045849 to PP045872
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP045901 to PP045932
PP045949 to PP045964
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP046001 to PP046048
PP046049 to PP046072
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP046101 to PP046148
PP046149 to PP046172
EST3X User Guide
No.
Annunciator
LED or switch
Address
21
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP046201 to PP046232
PP046249 to PP046264
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP046301 to PP046348
PP046349 to PP046372
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP046401 to PP046448
PP046449 to PP046472
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP046501 to PP046532
PP046549 to PP046564
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP046601 to PP046648
PP046649 to PP046672
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP046701 to PP046748
PP046749 to PP046772
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP046801 to PP046832
PP046849 to PP046864
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP046901 to PP046948
PP046949 to PP046972
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP047001 to PP047048
PP047049 to PP047072
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP047101 to PP047132
PP047149 to PP047164
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP047201 to PP047248
PP047249 to PP047272
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP047301 to PP047348
PP047349 to PP047372
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP047401 to PP047432
PP047449 to PP047464
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP047501 to PP047548
PP047549 to PP047572
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP047601 to PP047648
PP047649 to PP047672
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP047701 to PP047732
PP047749 to PP047764
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP047801 to PP047848
PP047849 to PP047872
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP047901 to PP047948
PP047949 to PP047972
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP048001 to PP048032
PP048049 to PP048064
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP048101 to PP048148
PP048149 to PP048172
22
23
24
25
26
27
EST3X User Guide
53
No.
28
29
30
54
Annunciator
LED or switch
Address
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP048201 to PP048248
PP048249 to PP048272
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP048301 to PP048332
PP048349 to PP048364
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP048401 to PP048448
PP048449 to PP048472
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP048501 to PP048548
PP048549 to PP048572
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP048601 to PP048632
PP048649 to PP048664
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP048701 to PP048748
PP048749 to PP048772
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP048801 to PP048848
PP048849 to PP048872
RLED-C or GCI
GCI
LED01 to LED32
SW01 to SW16
PP048901 to PP048932
PP048949 to PP048964
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP049001 to PP049048
PP049049 to PP049072
RLED24 or GCIX
GCIX
LED01 to LED48
SW01 to SW24
PP049101 to PP049148
PP049149 to PP049172
EST3X User Guide
Glossary
Term
Definition
activate
To turn on or energize. Pertains to outputs (including logical

outputs).
alarm
The state of a fire alarm initiating device that has detected a

smoke or fire condition. The state of a security device that has
been triggered.
AHJ
Authority having jurisdiction.
Alphanumeric LCD
Backlit liquid crystal display, 240 320 pixels, 24 lines of 40

characters. The LCD provides supplemental information
relevant to the current condition of the control panel.
card
Modules that connect to the electronics chassis and controldisplay modules.
device
Modules, circuits, buttons, or LEDs that exist on the electronics

chassis and all addressable devices connected by field wiring.
disable
Prevents an input, output, or system feature from functioning.
enable
Permits an input, output, or system feature to function.
group
A collection of Signature devices that is treated as a single

entity for programming purposes. Groups can have messages
and responses over and above the messages and responses of
the individual group members.
input
A signal generated by a field device and sent to the control

panel for evaluation and responses as determined by the
system database. Inputs to the system are detectors, modules,
and switches.
Normal state
The system is in a quiet state. The LCD screen shows no event

messages.
Off-normal state
The system enters the fire alarm, trouble, disabled, or test state.
The LCD screen shows event messages and system LEDs
indicate off-normal statuses.
output
A signal generated by the system, based upon responses

defined in the system database, and sent to external field
devices. Outputs are LEDs, and modules.
EST3X User Guide
55
Glossary
pseudo point
An input or output point that is not a physical device. For

example, ground fault and communication fault notifications.
reset
Refers to a condition of an input, where the input is not active. It

also refers to the condition of an output where the output is not
in its SET or RESET condition and does not have a priority
value associated with it.
rotary controller
A multifunctional control dial that performs the functions of a

computer keyboard and the Enter key. The controller is used to
scroll through and select events, menus, and commands and to
enter addresses.
RS-232
A serial communications format normally used for serial

peripheral devices (i.e., printers) from a computer.
SDU
System Definition Utility. A Windows-based program used to

enter and modify information contained in the system.
56
EST3X User Guide
Index
A
Acknowledge button, 22
acknowledging events, 22
addresses
backspacing, 12
alarm
report, 16
alarm count, 19
Alarm Silence button, 21
All Active points report, 16
Alternate Sensitivity, 26
B
backspacing, 12
basic function, 8
buzzer, 20
bypass
sensor messages, 32
bypassing photo element, 32
device (continued)
enable, 27
maintenance report, 17
disabled points
report, 16
disabling
devices, 27
zones, 28
displaying
device maintenance reports, 17
download
database, 29
drill
perform, 23
E
enabling
devices, 27
zone groups, 28
event messages, 9
capabilities, 2
carbon monoxide detection, 32
change rate, 33
restore rate, 33
changing
alarm sensitivity, 26
CO detection rate, 33
event message routes, 26
CO detection, 32
change rate, 33
restore rate, 33
finding database versions, 18

finding firmware versions, 18
D
database
download, 29
device
disable, 27
drill, 23
EST3X User Guide
G
Gas Accel command, 32
gateway address, 19
guard patrol routes, 31
activate, 31
restore, 31
H
history reports, 18
I
IP address, 19
57
Index
L
lamp test, 22
listed services, 2
M
maintenance
device report, 17
preventive, 36
routine schedule, 38
schedules, 36
service provider, 36
tests, 36
visual inspection schedule, 37
microphone
local, 13
monitor
report, 16
O
Outputs report, 16
overview
controls and indicators, 4
system, 2
P
page function buttons, 13
paging
local microphone, 13
panel buzzer, 20
Panel Silence button, 20
previous screen, 12
Primary Sensitivity, 26
printing
device maintenance reports, 17
PTT button, 13
R
Remote Read Lock, 30
Remote Write Unlock, 29
reports
device maintenance, 17
Reset button, 22
rotary controller, 11
S
schedule
routine maintenance, 38
visual inspection, 37
screen language, 23
58
selecting
alternate alarm sensitivity, 26
commands, 11
menus, 11
primary alarm sensitivity, 26
sensor
bypass messages, 32
restore messages, 32
setting time and date, 28
silencing
alarm signals, 21
panel buzzer, 20
Status menu commands
Alarm, 16
All Active, 16
Disabled Points, 16
Monitor, 16
Outputs, 16
Supervisory, 16
Test, 16
Trouble, 16
status reports, 16
subnet mask, 19
supervisory
report, 16
system
capabilities, 2
operation, 8
overview, 2
reset, 22
T
TCP/IP communications, 30
TCP/IP settings, 19
test
lamp test, 22
preventive maintenance, 36
report, 16
trouble
report, 16
troubleshooting, 39
U
user access levels, 10
user time out period, 10
V
viewing
status reports, 16
viewing event messages, 9
EST3X User Guide
Index
Z
zone
disable, 28
zone groups
enable, 28
EST3X User Guide
59
Index
60
EST3X User Guide

3101799-EN R1.0 EST3X User Guide PDF

Uploaded by

Copyright:

Available Formats

3101799-EN R1.0 EST3X User Guide PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3101799-EN R1.0 EST3X User Guide PDF

Uploaded by

Copyright:

Available Formats

EST3X User Guide

P/N 3101799-EN REV 1.0 ISS 10MAY11

2011 UTC Fire & Security. All rights reserved.

The EST3X name and EST logo are trademarks of

Edwards, A Division of UTC Fire & Security

This document applies to EST3X control panels with firmware

For contact information, see www.utcfireandsecurity.com.

Basic operating instructions 15

Advanced operating instructions 25

EST3X User Guide

Bypassing the photo element on SIGA2-PHS smoke

Preventive maintenance and testing 37

EST3X User Guide

EST3X FCC compliance

3-MODCOM FCC compliance

To ensure proper operation, this dialer must be installed according to the

EST3X User Guide

installation, and periodically thereafter, according to the enclosed test

A ringer equivalence number (REN) is used to determine how many devices

EST3X User Guide

The telephone company may make changes to its facilities, equipment,

3-MODCOM Industry Canada information

EST3X User Guide

Fire alarm system limitations

EST3X User Guide

EST3X User Guide

EST3X User Guide

EST3X User Guide

Commercial protected premises fire alarm control unit

Smoke control system

Releasing device control unit

Emergency communication and relocation

System hardware capabilities

250 addressable devices

Four Class B notification appliance or auxiliary power output circuits

30 remote or graphic annunciators for a total of 30 sets of common controls,

1,250 additional addressable devices (1,500 total)

24 Class B initiating device circuits

12 additional Class B notification appliance circuits (16 total)

Four Class A notification appliance or auxiliary power output circuits

EST3X User Guide

Three reverse polarity outputs

Three control-display modules for a total of 72 local LED indicators and 36

Two dialer outputs

One Ethernet connection for panel programming and diagnostics

Live voice and prerecorded audio messaging

Connection to an EST3X or EST3 life safety network using copper, fiber

EST3X User Guide

Overview of controls and indicators

11. Alarm Silence button and LED

12. Rotary controller

3. SUP (Supervisory) LED

4. GND Fault LED

14. Normal display screen (see Figure 2)

5. CPU Fail LED

15. Off -normal display screen

EST3X User Guide

Figure 2: Normal screen

Figure 3: Off-normal screen