Scribd
Upload
85 views

Processor Interface: Testrig - Fromhost Imem - Req - Addr Imem - Req - Val Testrig - Tohost CLK Reset

The document describes a test harness and memory interface for a RISC-V processor design. It includes: - A block diagram showing the processor connected to an instruction memory, data memory, and test harness through various request and response signals. - Details on how to make instruction and data memory requests, with instruction data returned combinationally and data writes occurring at the end of the clock cycle. - Mention that there are separate test harnesses for the Chisel emulator and generated Verilog, with the designer first passing the emulator tests before running Verilog tests during synthesis.

Uploaded by

JohnPJojo
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
85 views

Processor Interface: Testrig - Fromhost Imem - Req - Addr Imem - Req - Val Testrig - Tohost CLK Reset

The document describes a test harness and memory interface for a RISC-V processor design. It includes: - A block diagram showing the processor connected to an instruction memory, data memory, and test harness through various request and response signals. - Details on how to make instruction and data memory requests, with instruction data returned combinationally and data writes occurring at the end of the clock cycle. - Mention that there are separate test harnesses for the Chisel emulator and generated Verilog, with the designer first passing the emulator tests before running Verilog tests during synthesis.

Uploaded by

JohnPJojo
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Processor Interface

riscvTestHarness
Cpu
testrig_fromhost
imem.req_addr
imem.req_val
testrig_tohost
clk
reset
Instruction
Memory
Data
Memory
imem.resp_data
dmem.req_rw
dmem.req_addr
dmem.req_wdata
dmem.req_val
dmem.resp_data clk
clk

Figure 1: Block diagram for RISC-V-v2 Processor Test Harness


We have given you a 1-stage processor which already has a working interface to a
test harness
and memories. The test harness will drive the inputs and check the outputs of your
design for
a number of tests written in assembly language. These tests are targeted to verify
correct functionality of every instruction. The test harness includes the data and instruction
memories. We
have provided separate instruction and data memory ports to simplify the
construction of the
pipeline, but both ports access the same memory space. The memory ports can
only access 32-bit
words, and so the lowest two bits of the addresses are ignored (i.e., only imemreq
bits addr[31:2]
and dmemreq bits addr[31:2] are signi_cant). To make an instruction memory
request, set
imemreq bits addr to the fetch address and set imemreq val to one. The data will be
returned
combinationally (i.e. there are no clock edges between when a request is made and
when the response returns). To make a data memory request set dmemreq bits rw to zero for a
load or one for
a store, set dmemreq bits addr to the address, set dmemreq bits data to the store
data if needed,
and _nally set dmemreq val to one. The data will be returned combinationally for
loads, while for
stores the data will be written at the end of the current clock cycle. Notice that the
data write bus
is a separate unidirectional bus from the data read bus. Bidirectional tri-state buses
are usually

avoided on chip in ASIC designs.


CS250 Lab Assignment 2 (Version 082511), Fall 2011 3

Test Harness

There are two test harnesses: one for the Chisel-generated emulator, and another
for the Chiselgenerated Verilog. You should design your processor such that it passes the
emulator testbench
_rst. Then, when you are ready to synthesize your design, you should run the Verilog
testbench to
ensure that there are no bugs in the Chisel verilog generator.
We are providing a test harness to connect to your processor model. The test
harness is identical
to the one described in Tutorial 4: Simulating Verilog RTL using Synopsys VCS and
Tutorial 5:
RTL-to-Gates Synthesis using Synopsys Design Compiler. The test harness loads a
RISC-V binary
into the memory. The provided make_le can load both assembly tests as well as C
benchmarks
to run on your processor. The test harness will clock the simulation until it sees a
non-zero value
coming back on the testrig tohost register, signifying that your processor has
completed a test
program. The testr

You might also like