Scribd
Upload
626 views4 pages

Design of Two Way Slab (IS 456:2000) (Limit State Method) : 1 Analysis

The document summarizes the design of a two-way slab using the limit state method. The slab has dimensions of 3.58m x 5.18m. The required depth is calculated as 125mm. Reinforcement is designed to resist bending moments at supports and at mid-spans. Main reinforcement consists of 8Ø bars at 175mm c/c in the +ve moment regions and 10Ø bars at 175mm c/c in the -ve moment regions. Shear, development length, and deflection checks confirm the design is adequate.

Uploaded by

Rus Theeng
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
626 views4 pages

Design of Two Way Slab (IS 456:2000) (Limit State Method) : 1 Analysis

The document summarizes the design of a two-way slab using the limit state method. The slab has dimensions of 3.58m x 5.18m. The required depth is calculated as 125mm. Reinforcement is designed to resist bending moments at supports and at mid-spans. Main reinforcement consists of 8Ø bars at 175mm c/c in the +ve moment regions and 10Ø bars at 175mm c/c in the -ve moment regions. Shear, development length, and deflection checks confirm the design is adequate.

Uploaded by

Rus Theeng
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Design of Two way slab (IS 456:2000) (Limit State Method)

Analysis:
Short span
Long Span

B or Lx =
L or Ly =

3.58 m
5.18 m

Input Data:
Size of Slab is =
Slab is contineous over T-Beam
Material use
Concrete
Steel

5.18

3.58 sq. m

M20
Fe500

20 N/mm2
500 N/mm2

xu/d =

Effective Span:
Lx =
Ly =
Ly/Lx=
From preliminary design the overall depth is

3.58 m
5.18 m
1.4 < 2 Two Way Slab
D=

ii

iii

iv

I) Dead Load (DL)


Slab
Thickness
Dead load of Slab = 25 KN/m3 *
0.125m =
Screeding
Thickness
Dead load of Screeding = 20.4 KN/m3
* 0.03m =
19mm thick Marble Flooring
Thickness
Dead load of 19mm thick Marble
Flooring = 27 KN/m3 * 0.019m =
Cement Plaster
Thickness
Dead load of Cement Plaster = 20.4
KN/m3 * 0.0125m =
Total of (I + ii + iii + iv)
I) Live Load (LL)
For Residensial
Total Design Load (DL + LL)
The Factored Load (Wu) = 1.5*Design
Load =

125 mm

25 KN/m3

3.125 KN/m2
30 mm

20.4 KN/m3

0.612 KN/m2
19 mm

27 KN/m3

0.513 KN/m2
12.5 mm

20.4 KN/m3

0.255 KN/m2
4.51 KN/m2

2 KN/m2
6.51 KN/m2
9.765 KN/m2

1.5 Factor

Critical Support Condition:


Two adjacent edge discontinuous
Consider one meter width of slab along short span & along long span.

Calculation of Moments:
Short Span

125 mm

Calculation of Load:
I

0.46

-ve moment at contineous edge (support)

x1

0.07100

Long Span
y1
0.047

+ve moment at mid span


Along Short Span:
-ve moment at contineous edge (support)
-Mx = x1*wu*lx2
-My = y1*wu*lx2
Along Long Span:
+ve moment at mid span
+Mx = x2*wu*lx2
+My = y2*wu*lx2

x2

0.05300

y2

0.35

8.89 KN-m
5.88 KN-m

6.63 KN-m
43.80 KN-m

Depth Calculation:
Minimum depth of slab is calculated considering maximum bending moment.
Here obs maximum bending moment is
Mu=
Depth Required (d) = sqrt(Mu/(0.36*xumax/d*(1-.42*xumax/d)*b*fck))
Overall depth
D=d+/2+clear cover
Hence, for safe design adopt above more depth
D=
Effective Depth (main) dx= D-1/2-clear cover
Effective Depth (secondary) dy= D-clear cover-main steel dia- 2/2

8.89 KN-m
128.03 mm
149.03 mm
125 mm
104 mm
95 mm

Not OK

Reinforcement Calculation:
Moment
Support
-ve Mx
Moment (KN-m)
8.89
Solving quadratic equation Mu=0.87fyAstd(1-Astfy/bdfck)
a = 0.87*fy^2/(b*fck)
10.88
b=-0.87fyd
-45240.00
c=Mu
8885802.37
x=(-b+-sqrt(b2-4ac))/2a
x1=(-b+sqrt(b2-4ac))/2a
3953.32
x2=(-b-sqrt(b2-4ac))/2a
206.68
Astx (mm2) =
206.68
Ast req. (mm2)
206.68
Min As(0.12%bD) mm2
150
Ast Actually required as per
minimum reinforcement (mm2)
206.68
Spacing =b*area of one bar/Ast
380.00

Mid Span
-ve My
5.88

+ve Mx
6.63

+ve My
43.80

10.88
-41325.00
5882150.86

10.88
-45240.00
6633063.74

3651.89
148.11
148.11
148.11
150

4007.81
152.19
152.19
152.19
150

150.00
523.60

152.19
330.29

10.88
-41325.00
43803251.10
#NUM!
#NUM!
#NUM!
#NUM!
150
#NUM!
#NUM!

3d
312
312
312
312
300
300
300
300
300
Adopt the spacing (min of above three)
300.00
300.00
300.00
#NUM!
Spacing provided in mm
175
175
175
175
Ast provided (mm2)
448.80
448.80
287.23
287.23
% of Ast (Provided)
0.36
0.36
0.23
0.23
Main Reinforcement
10 @ 175mm c/c 10 @ 175mm c/c 8 @ 175mm c/c 8 @ 175mm c/c

Minimum of 3d or
300

Check:
7.1 Minimum Reinforcement
Min As(0.12%bD) mm2
7.2 Check for Shear
In slab shear is checked along short edge.
Max Shear Force (V) = w*lx/2
v=V/bd

150 mm2

% of steel provided
% of steel=(100*Asty/2)/bd
Shear capacity of section without reinforcement
c from table
100As/bd
0.25
0.5
Shear strength for slab ' = kc
The provided Depth of slab (D) =
D
Since the depth of slab <150mm the value of K=125
' = kc
7.3 Check for Development length
Ld<=1.3M1/V+Lo
a) At short edge
Ld= s*/(4Tbd)
Tbd from IS 456:2000 26.2.1.1 Page 43
M1= 0.87*Asty/2*fy(d-Asty/2*fy/(b*fck))
Lo= 96

<Astx(+ve),Asty(+ve),Astx(-ve),Asty(-ve)

17.47935 KN
0.168 N/mm2
0.36 %

M20
0.36
0.48

0.41 N/mm2
125.00 mm

k
1.3

1.30
0.54 N/mm2 > v

56.64
For deformed bar increase by 60%
9.88
12 or d which ever is greater
Ld<=1.3M1/V+Lo
830.66
56.64=
566.41

Safe in shear

M20
1.2

KN-m
mm
mm
OK in development length

At long edge
Ld= s*/(4Tbd)
M1= 0.87*Asty/2*fy(d'-Asty/2*fy/(b*fck))
Lo= 96

56.64

M20
1.2

8.73 KN-m
12 or d which ever is greater
Ld<=1.3M1/V+Lo
744.96 mm
56.64=
453.13 mm
OK in development length

7.4 Check for deflection


From deflection criteria, we have,
l/d<=
where,
= Basic value of span to effective depth ratios for spans up to spans 10m
=
26 (Since span<10m)
= a factor which accounts for correction in the values of for spans greater than 10m
=
1
= a factor which depends on the stress at service and amount of steel for tension reinforcement
Area of steel of required
#NUM!
mm2
Area of steel of provided
448.80 mm2

% of steel provided

0.36 %
fs=0.58*fy*Ast req./Ast provided
#NUM!
N/mm2
from graph () =
1.98
= a factor which depends on the area of compression reinforcement.
=
1
= a factor for flanged beams which depends on the ratio of web width to the flange width
=
1
lx/d permissible
=
51.48
lx/d provided = 3580/104 =
34.42

Summary:
Overall Depth of slab = 125 mm
Main Bar:
Astx +ve = 8 @ 175mm c/c
Astx -ve = 10 @ 175mm c/c
Asty +ve = 8 @ 175mm c/c
Asty -ve = 10 @ 175mm c/c

Safe in deflection

ate Method)

You might also like