Manual de SCR dd15

DDC-SVC-MAN-0189
DD Platform Operators Manual
Specifications are subject to change without notice. Detroit Diesel

Corporation is registered to ISO 9001:2001.
Copyright Detroit Diesel Corporation. All rights reserved. Detroit
Diesel Corporation is a Daimler company.
Printed in U.S.A.
Table of Contents
Table of Contents
California Proposition 65 Warning and Engine Idle Notice......................... 5
Forward............................................................................................................. 6
Introduction.................................................................................................... 6
Non-Genuine and Rebuilt Component Quality Alert.................................... 6
Personnel Requirements................................................................................ 6
Engine Conversions and Modifications......................................................... 7
To the Operator................................................................................................ 8
Caution Summary........................................................................................... 10
Engine Identification...................................................................................... 17
Engine Components - EPA07, EPA10, GHG14 DD Platform.................... 17
Engine Components - GHG17 DD Platform............................................... 24
Engine Model and Serial Number Designation........................................... 30
Operating Instructions for Starting the Engine........................................... 36
First Time Start Preparations....................................................................... 36
Detroit Diesel Electronic Controls (DDEC) System.................................... 54
DDEC VI System - EPA07.......................................................................... 54
DDEC 10 System - EPA10/GHG14............................................................ 57
Detroit Diesel Electronic Control System Operation.................................. 60
Detroit Diesel Electronic Control System Features..................................... 64
Accelerating the Vehicle.............................................................................. 68
Cruise Control.............................................................................................. 68
Engine Brake and Cruise Control................................................................ 71
DD Platform Shifting................................................................................... 71
Idling............................................................................................................ 72
Engine Brake System...................................................................................... 73
Driver Control Switches.............................................................................. 73
Clutch Pedal and Throttle Position Controls............................................... 73
Engine Brake Activation Conditions........................................................... 73
Engine Brake Operation............................................................................... 74
Anti-Lock Braking Systems........................................................................ 75
Operating on Flat, Dry Pavement................................................................ 75
Operating Down a Long, Steep Grade......................................................... 75
Operating on Wet or Slippery Pavement..................................................... 76
Engine Systems............................................................................................... 78
EPA07 Aftertreatment Device....................................................................... 80
EPA10 Aftertreatment System...................................................................... 81
GHG14 Aftertreatment System..................................................................... 84
GHG17 Aftertreatment System..................................................................... 85
Diesel Exhaust Fluid Information................................................................. 87
Aftertreatment Device Operating Requirements........................................ 88
EPA10 Diesel Exhaust Fluid (DEF) Purge Cycle........................................ 89
EPA10/GHG14/GHG17 Diesel Exhaust Fluid Tank................................... 90
Aftertreatment Maintenance......................................................................... 91
2
All information subject to change without notice.
Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189
Performing a Parked Regeneration - EPA07............................................... 92

Performing a Parked Regeneration - EPA10/GHG14................................ 94
Performing a Parked Regeneration - GHG17............................................. 96
Hazardous Applications................................................................................. 98
Service Record................................................................................................ 99
Instrument Panel Lamps.............................................................................. 100
EPA10/GHG14/GHG17 Diesel Exhaust Fluid Level Warning Lamps.... 104
Aftertreatment System Driver Notifications and Actions......................... 105
DEF Post-Run Indicator Lamp................................................................... 109
DEF Post-Run Indicator Lamp.................................................................. 109
Preventive Maintenance Intervals.............................................................. 110
EPA07 DD Series Preventive Maintenance Tables................................... 115
EPA10/GHG14/GHG17 DD Series Preventive Maintenance Tables....... 118
EPA10/GHG14/GHG17 DD Series Preventive Maintenance Tables for
Recreational Vehicles................................................................................... 122
Routine Preventive Maintenance................................................................ 124
Monitoring the Lubricating Oil................................................................. 124
Monitoring the Lubricating Oil Filter........................................................ 125
Monitoring the Cooling System................................................................. 126
Inspection of the Radiator.......................................................................... 127
Monitoring the Cooling System Filter....................................................... 128
Monitoring the Fuel Filters........................................................................ 128
Adjusting the Valve Lash.......................................................................... 129
Monitoring the Belt Tensioner................................................................... 129
Poly-V-Belt Inspection.............................................................................. 129
Monitoring the Serpentine Belts................................................................ 131
Inspection of the Air Intake System.......................................................... 132
Monitoring the Air Cleaner........................................................................ 132
Monitoring the Exhaust System................................................................. 133
Monitoring the Aftertreatment System...................................................... 133
Inspection of the Air Compressor.............................................................. 133
Monitoring the Fuel and Fuel Tank........................................................... 133
Inspection of Hoses and Fittings for Fuel Leaks....................................... 134
Inspection of the Turbocharger and Charge Air Cooler............................ 135
Inspection of the Battery............................................................................ 135
Steam Cleaning the Engine........................................................................ 136
Inspection of the Battery-Charging Alternator.......................................... 137
Lubricating the Fan Hub............................................................................ 137
Checking the Vibration Damper................................................................ 138
How to Procedures........................................................................................ 139
How to Select Lubricating Oil................................................................... 139
When to Change Oil.................................................................................. 140
How to Replace the Lubricating Oil and Oil Filter................................... 141
How to Select Diesel Fuel......................................................................... 143
How to Replace the Fuel Filters - Two- and Three-Filter Systems........... 145
DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION
Table of Contents
Engine Out of Fuel How to Restart........................................................ 158

How to Clean an Engine............................................................................ 159
Cleaning/Flushing the Cooling System..................................................... 160
Coolant Selections and Maintenance......................................................... 161
Coolant Fill Options.................................................................................. 162
Coolants for Detroit Engines................................................................. 164
Maintenance............................................................................................... 166
Appendix A - Definitions.......................................................................... 171
Appendix B - General Coolant Information.............................................. 172
Appendix C - Detroit Cooling System Maintenance Products.............. 175
How to Replace the Coolant Filter............................................................ 177
Checking the Hoses................................................................................... 178
How to Service the Dry Type Air Cleaner................................................ 179
Engine Storage.............................................................................................. 180
Preparing Engine for Storage..................................................................... 180
Procedure for Restoring to Service an Engine that Has Been in Extended
Storage....................................................................................................... 183
Customer Assistance..................................................................................... 185
Using Road Service in the U.S. or Canada................................................ 185
Availability of Detroit Service Outlets.................................................. 185
Detroit Genuine Coolant Engine Products................................................. 187
Engine Oil Capacities................................................................................... 189
California Proposition 65 Warning and Engine Idle

Notice
Forward
Forward
Introduction
This manual is intended for use by the operator of a Detroit engine used in OnHighway Vehicle applications.
Non-Genuine and Rebuilt Component Quality Alert

Electronic engine controls have been instrumental in aiding engine manufacturers
in meeting the stringent emission requirements of the U.S. Environmental
Protection Agency (EPA) and the California Air Resources Board (CARB) and also
in meeting the ever-increasing performance demands of the customer.
Maintenance procedures must be followed in order to continue satisfactory
performance and durability and to ensure coverage of the engine under the
manufacturers warranty. Many of these maintenance procedures also ensure that
the engine continues to comply with applicable emissions standards. Proper
maintenance procedures, using specific components engineered to comply with
emissions regulations, may be performed by an authorized Detroit distributor or
dealer, an independent outlet or the operator or owner. The owner is responsible for
determining the suitability of components to maintain emissions compliance during
the engines useful emission life.
Detroit cautions that the indiscriminate rebuilding of precision components,
without the benefit of specifications, specialized equipment, and knowledge of the
electronic operating system, will jeopardize performance or lead to more serious
problems, and can take the engine outside of compliance with U.S. EPA or CARB
emissions standards.
There are several other components in an engine, such as turbocharger, camshaft,
piston, fuel doser valve, fuel doser block, diesel particulate filter (DPF), diesel
exhaust fluid pump (for EPA10/GHG14 engines), which are specifically designed
and manufactured to exacting standards for emissions compliance. It is important
that these components, if replaced, modified or substituted, can be verified to
ensure that the engine remains in compliance with emissions standards. The use of
inadequately engineered, manufactured or tested components in repair or rebuild of
the engine may be in violation of the federal Clean Air Act and applicable U.S.
EPA or CARB regulations.
Furthermore, modern engines exhibit operating parameters which require the use of
proper fluids, such as fuel, coolant and lubricating oil, to maintain long engine life.
The use of fluids that do not meet Detroit specifications may result in premature
wear or engine failure.
Personnel Requirements
Work on the engine should be carried out only by skilled technicians who have
been instructed in the specific skills necessary for the type of work being
performed.
Engine Conversions and Modifications

The function and safety of the engine could be affected if unauthorized
modifications are made to it. Detroit will not accept responsibility for any
resulting damage.
Tampering with the fuel injection system and engine electronics could also affect
engine power output or exhaust emission levels. Compliance with the
manufacturer's settings and with statutory environmental protection regulations
cannot then be guaranteed.
To the Operator
To the Operator
This manual contains instructions on the safe operation and preventive maintenance
of your Detroit engine used in vehicle applications. Maintenance instructions
cover routine engine services such as lubricating oil and filter changes in enough
detail to permit self-servicing, if desired.
The operator should become familiar with the contents of this manual before
operating the engine or carrying out maintenance procedures.
Power-driven equipment is only as safe as the person operating the controls. You
are urged, as the operator of this diesel engine, to keep fingers and clothing away
from the revolving belts, drive shafts, pulleys, etc. on the engine installation.
Throughout this manual CAUTIONS and WARNINGS regarding personal safety
and NOTICES regarding engine performance or service life will appear. To avoid
personal injury and ensure long engine service life, always heed these instructions.
Whenever possible, it will benefit you to rely on an authorized Detroit service
outlet for all your service needs from maintenance to major parts replacement.
Authorized service outlets worldwide stock factory-original parts.
The information and specifications in this publication are based on the information
in effect at the time of approval for printing. Contact an authorized Detroit
service outlet for information on the latest revision. The right is reserved to make
changes at any time without obligation.
Detroit engines are built in accordance with sound technological principles and
based on state-of-the-art technology.
Despite this, the engine may constitute a risk of damage to property or injury to
persons if it is not used for its intended purpose.
The engine should not be modified or converted in an incorrect manner or the
safety instructions included in this manual disregarded.
Keep this Operator Manual with the engine installation at all times. It contains
important operating, maintenance, and safety instructions.
NOTICE: Failure to maintain the cooling system at required
concentrations will result in severe damage to the engine cooling
system and related components. Refer to the "Coolant Selections and
Maintenance" section.
Table 1.
WARRANTY
The applicable engine warranty is contained in the booklet Warranty Information for
Detroit Engines, available from authorized Detroit service outlets.
Trademark Information
DDC, Detroit, DDEC, Optimized Idle, Diagnostic Link, BlueTec,
POWER Trac, POWER COOL, and POWER GUARD are registered
trademarks of Detroit Diesel Corporation. All other trademarks used are the
property of their respective owners.
Caution Summary
Caution Summary
The following cautions must be observed by the operator of the vehicle or
equipment in which this engine is installed and/or by those performing basic engine
preventive maintenance. Failure to read and heed these cautions and exercise
reasonable care for personal safety and the safety of others when operating the
vehicle/equipment or performing basic engine preventive maintenance may result
in personal injury and engine and/or vehicle/equipment damage.
Engine Operation
Observe the following cautions when operating the engine.
WARNING: PERSONAL INJURY
To avoid injury from loss of vehicle/vessel control, the operator of
a DDEC equipped engine must not use or read any diagnostic
tool while the vehicle/vessel is moving.
WARNING: HOT EXHAUST
During parked regeneration the exhaust gases will be extremely
HOT and could cause a fire if directed at combustible materials.
The vehicle must be parked outside.
CAUTION: LOSS OF VEHICLE CONTROL
To avoid injury from the loss of vehicle control, do not use cruise
control under these conditions:
When it is not possible to keep the vehicle at a constant speed
(on winding roads, in heavy traffic, in traffic that varies in
speed, etc.).
On slippery roads (wet pavement, ice-or snow-covered roads,
loose gravel, etc.).
Diesel engine exhaust and some of its constituents are known to
the State of California to cause cancer, birth defects, and other
reproductive harm.
Always start and operate an engine in a well ventilated area.
If operating an engine in an enclosed area, vent the exhaust to
the outside.
Do not modify or tamper with the exhaust system or emission
control system.
10

To avoid injury from engine shutdown in an unsafe situation,
ensure the operator knows how to override the stop engine
condition on a DDEC-equipped unit.
To avoid injury from loss of vehicle control, do not activate the
Engine Brake system under the following conditions:
On wet or slippery pavement, unless the vehicle is equipped
with ABS (anti-lock braking system) and you have had prior
experience driving under these conditions.
When driving without a trailer (bobtailing) or pulling an empty
trailer.
If the tractor drive wheels begin to lock or there is fishtail
motion after the Engine Brake is activated, deactivate the brake
system immediately if this occurs.
WARNING: BODILY INJURY
To avoid injury from an explosion, do not use ether or starting
fluid on engines equipped with a manifold (grid) heater.
Preventive Maintenance
Observe the following cautions when performing preventive maintenance.
To avoid injury when working near or on an operating engine,
remove loose items of clothing and jewelry. Tie back or contain
long hair that could be caught in any moving part causing injury.
To avoid injury when working on or near an operating engine,
wear protective clothing, eye protection, and hearing protection.
WARNING: HOT OIL
To avoid injury from hot oil, do not operate the engine with the
rocker cover(s) removed.
11
Caution Summary
WARNING: FIRE
To avoid injury from fire, contain and eliminate leaks of flammable
fluids as they occur. Failure to eliminate leaks could result in fire.
CAUTION: USED ENGINE OIL
To avoid injury to skin from contact with the contaminants in used
engine oil, wear protective gloves and apron.
To avoid injury when using caustic cleaning agents, follow the
chemical manufacturers usage, disposal, and safety instructions.
To avoid injury from hot surfaces, wear protective gloves, or allow
engine to cool before removing any component.
To avoid injury, use care when working around moving belts and
rotating parts on the engine.
WARNING: FIRE
To avoid injury from combustion of heated lubricating-oil vapors,
stop the engine immediately if an oil leak is detected.
To avoid injury from contact with rotating parts when an engine is
operating with the air inlet piping removed, install an air inlet
screen shield over the turbocharger air inlet. The shield prevents
contact with rotating parts.
WARNING: HOT COOLANT
To avoid scalding from the expulsion of hot coolant, never
remove the cooling system pressure cap while the engine is at
operating temperature. Wear adequate protective clothing (face
shield, rubber gloves, apron, and boots). Remove the cap slowly
to relieve pressure.
12
WARNING: FIRE
To avoid injury from fire, do not smoke or allow open flames
when working on an operating engine.
WARNING: FIRE
To avoid injury from fire from a buildup of volatile vapors, keep
the engine area well ventilated during operation.
To avoid injury from rotating belts and fans, do not remove and
discard safety guards.
To avoid injury from slipping and falling, immediately clean up
any spilled liquids.
Compressed Air
Observe the following cautions when using compressed air.
WARNING: EYE INJURY
To avoid injury from flying debris when using compressed air,
wear adequate eye protection (face shield or safety goggles) and
do not exceed 276 kPa (40 psi) air pressure.
Cooling System
Observe the following cautions when servicing the cooling system.
13
Caution Summary
Electrical System
Observe the following cautions when jump starting an engine, charging a battery,
or working with the vehicle/application electrical system.
WARNING: ELECTRICAL SHOCK
To avoid injury from electrical shock, do not touch battery
terminals, alternator terminals, or wiring cables while the engine
is operating.
WARNING: Battery Explosion and Acid Burn
To avoid injury from battery explosion or contact with battery acid,
work in a well ventilated area, wear protective clothing, and avoid
sparks or flames near the battery. If you come in contact with
battery acid:
Flush your skin with water.

Apply baking soda or lime to help neutralize the acid.
Flush your eyes with water.
Get medical attention immediately.

To avoid injury from accidental engine startup while servicing the
engine, disconnect/disable the starting system.
Air Intake System
Observe the following cautions when working on the air intake system.
To avoid injury from contact with rotating parts when an engine is
operating with the air inlet piping removed, install an air inlet
screen shield over the turbocharger air inlet. The shield prevents
contact with rotating parts.
Lubricating Oil and Filters
Observe the following cautions when replacing the engine lubricating oil and filter.
14

WARNING: FIRE
To avoid injury from combustion of heated lubricating-oil vapors,
stop the engine immediately if an oil leak is detected.
WARNING: FIRE
To avoid injury from fire, do not smoke or allow open flames
when working on an operating engine.
WARNING: FIRE
To avoid injury from fire from a buildup of volatile vapors, keep
the engine area well ventilated during operation.
Fuel System
Observe the following cautions when fueling the vehicle or working with the fuel
system.
WARNING: FIRE
To avoid injury from fire, keep all potential ignition sources away
from diesel fuel, including open flames, sparks, and electrical
resistance heating elements. Do not smoke when refueling.
To prevent the escape of high pressure fuel that can penetrate
skin, ensure the engine has been shut down for a minimum of 10
minutes before servicing any component within the high pressure
circuit. Residual high fuel pressure may be present within the
circuit.
WARNING: FIRE
To avoid increased risk of a fuel fire, do not mix gasoline and
diesel fuel.
15
Caution Summary
WARNING: FIRE
To avoid injury from fire caused by heated diesel-fuel vapors:
Keep those people who are not directly involved in servicing
away from the engine.
Stop the engine immediately if a fuel leak is detected.
Do not smoke or allow open flames when working on an
operating engine.
Wear adequate protective clothing (face shield, insulated
gloves and apron, etc.).
To prevent a buildup of potentially volatile vapors, keep the
engine area well ventilated during operation.
Aftertreatment System
Observe the following cautions when servicing the Aftertreatment System (ATS).
Be advised that these two labels are attached to the Aftertreatment Device (ATD).
16
Engine Identification
Engine Components - EPA07, EPA10, GHG14 DD Platform
All DD Platform engine components are shown below:
DD13 Engine Components
NOTE: Engines built prior to 2015 may have a coolant filter and a fuel filter
module with three filters.
For a general view of the Detroit DD13 engines and major components, see the
following:
1.
2.
3.
4.
5.
6.
7.
Water Pump
Oil Coolant Module
Oil Filter
Fuel Rail
Air Intake Manifold
Fuel Doser Block
High Pressure Fuel Pump
8.
9.
10.
11.
12.
13.
Single-stage Air Compressor

Power Steering Pump Location
Fuel Filter Module
MCM
Thermostat
Engine Serial Number Location
Figure 1. DD13 Left Side View

17
1.
2.
3.
4.
EGR Actuator
Exhaust Manifold
EGR Cooler
Coolant Elbow
5. Turbocharger
6. Fuel Doser Valve
7. Crankcase Breather
Figure 2. DD13 Right Side View

For a general view of the Detroit DD15 Turbo-compound (TC) and DD15
Asymmetrical Turbo (AT) engines and major components, see the following:
18
1.
2.
3.
4.
5.
6.
7.
Water Pump
Oil/Coolant Module
Oil Filter
Air Intake Manifold
Fuel Rail
Hydrocarbon Doser Block
8.
9.
10.
11.
12.
13.
Single Cylinder Air Compressor

Fuel Filter Module
Motor Control Module (MCM)
Thermostat
Figure 3. DD15 TC Left Side View
19
1. Exhaust Gas Recirculation (EGR)

Cooler
Valve / Actuator
3. Turbocharger
5. Axial Power Turbine (APT)
6. Fuel Doser Valve (under cover)
Figure 4. DD15 TC Right Side View
20
1.
2.
3.
4.
5.
6.
7.
Water pump
Oil Coolant Module
Oil Filter
Air Intake Manifold
Fuel Rail
8.
9.
10.
11.
12.
13.
Single Cyl. Air Compressor

Fuel Filter Module
MCM
Thermostat
Figure 5. DD15 AT Left Side View
21

Valve / Actuator
Cooler
3. Turbocharger
4. Fuel Doser Valve

Figure 6. DD15 AT Right Side View

For a general view of the Detroit DD16 engines and major components, see the
following:
22
1.
2.
3.
4.
5.
6.
7.
Water Pump
Oil/Coolant Module
Oil Filter
Air Intake Manifold
Fuel Rail
8.
9.
10.
11.
12.
13.
Single Stage Air Compressor

Fuel Filter Module
Thermostat
Figure 7. DD16 TC Left Side View
23
1. EGR Cooler
2. EGR Actuator
3. Turbocharger (TC)
5. Axial Power Turbine (APT) (under
heat shield)
6. Fuel Doser Valve (under cover)
Figure 8. DD16 TC Right Side View
Engine Components - GHG17 DD Platform

GHG17 Platform engine components are shown below:
For a general view of the Detroit engines and major components, see the
following:
24
1.
2.
3.
4.
5.
6.
Water Pump
Oil Coolant Module
Oil Filter
Fuel Rail
Air Intake Manifold
7.
8.
9.
10.
11.
12.

Single-stage Air Compressor
Fuel Filter Module
Coolant Thermostat
25
1. EGR Actuator
2. Exhaust Manifold
3. EGR Cooler Water Manifold
Assembly
4. Coolant Outlet Elbow
5. Turbocharger
6. Fuel Doser Injector Valve

following:
26
1.
2.
3.
4.
5.
6.
7.
Water Pump
Oil/Coolant Module
Oil Filter
Air Intake Manifold
Fuel Rail
8.
9.
10.
11.
12.
13.
Single Cylinder Air Compressor

Power Steering Pump Adaptor
Fuel Filter Module
Coolant Thermostat
27
1. EGR Actuator
2. EGR Cooler
3. Turbocharger
4. Fuel Doser Injector Valve


following:
28
1.
2.
3.
4.
5.
6.
7.
Water Pump
Oil/Coolant Module
Oil Filter
Air Intake Manifold
Fuel Rail
8.
9.
10.
11.
12.
13.
Single Stage Air Compressor

Power Steering Pump Adaptor
Fuel Filter Module
Coolant Thermostat
29
1. EGR Cooler
2. EGR Actuator
3. Turbocharger
5. Axial Power Turbine (APT)
6. Fuel Doser Injector Valve (under
cover)
Engine Model and Serial Number Designation

The following information covers engine model number, serial number and
certification label.
Engine Model and Serial Number
The fourteen-digit engine model and manufacturing serial number is etched on a
pad located on the left front of the engine cylinder block, above the date and time
of manufacture. Using 472901S0005703 as an example:
30
472 = engine model (DD15)

901 = vehicle application (Freightliner)
S = assembly plant (Detroit)
0005703 = serial number
Figure 15. Engine Model and Serial Number Location

Engine Model Breakdown
471 - DD13
472 - DD15
473 - DD16
Motor Control Module and Engine Serial Number
The Motor Control Module (MCM) part number and Engine Serial Number (ESN)
are located on the MCM label.
31
Figure 16. Motor Control Module Label

Engine Certification Label
An engine certification label is attached to the engine rocker cover. This label
certifies the engine conforms to federal and state emissions regulations for its
application. It gives the operating conditions under which certification was made.
The following illustration is an EPA07 engine certification label.
Figure 17. EPA07 Engine Certification Label

The following illustration is an EPA10 engine certification label.
32
Figure 18. EPA10 Engine Certification Label

The following illustrations are for GHG14 and GHG17 engine certification labels.
33
Figure 19. GHG14 Engine Certification Label
34
Figure 20. GHG17 Engine Certification Label
35
Operating Instructions for Starting the Engine

First Time Start Preparations
When preparing to start a new (or newly overhauled) engine, which has been in
storage, perform all of the operations listed below. Failure to follow these
instructions may result in serious engine damage.
Be sure you are familiar with all of the instruments, gauges and controls which are
needed to operate the engine.
Note especially the location and function of the following:
Oil pressure gauge

Low oil pressure warning light
Coolant temperature gauge
High coolant temperature warning light
Water-in-Fuel warning light in the side of the fuel filter module
Air restriction indicator
Watch for any signs of engine problems when starting or driving. If the engine
overheats, uses excessive fuel or lubricating oil, vibrates, misfires, makes unusual
noises or shows an unusual loss of power, turn the engine off as soon as possible
and determine the cause of the problem. Engine damage may be avoided by a quick
response to early indications of problems.
When starting the engine in cold weather, Refer to section "Cold Weather
Operation"
System Checks
Perform the following system checks before starting for the first time.
Checking the Cooling System
Check the cooling system as follows:
1. Make sure all drain cocks in the cooling system are installed (drain cocks are
often removed for shipping) and are closed tightly.
2. Fill the coolant overflow surge tank with Detroit Genuine Coolant until
coolant level stays between the low and full coolant marks on the tank.
3. Entrapped air must be purged after filling the cooling system. To do this,
allow the engine to warm up with the pressure cap removed. With the
transmission in neutral, increase engine speed to 1000 rpm and add coolant
to the surge tank as required.
4. Check to make sure the front of the radiator and charge air cooler (if
equipped) are unblocked and free of debris.
36
Lubrication System Checks

The lubricating oil film on the rotating parts and bearings of a new or newly
overhauled engine, or one which has been in storage for six months or more, may
be insufficient when the engine is started for the first time.
Pre-Lubricating the Engine
To ensure an immediate flow of oil to all bearing surfaces at initial engine startup,
prepare the engines as follows:
NOTICE:
Insufficient lubrication at startup can cause serious damage to engine
components.
Do not add oil if the oil reading falls on the crosshatch area of the
dipstick. There are approximately 5.0 L (5.2 qt) from the fill mark to the
full mark. Overfilling the oil pan can cause engine damage.
1. Charge the engine lubrication system with lubricating oil using a
commercially-available pressure pre-lubricator.
2. Charge the engine lubrication system with lubricating oil using a
commercially-available pressure pre-lubricator. Use only the heavy-duty
oils recommended in the "How to Replace the Lubricating Oil and Oil
Filter" section in this manual.
3. After pre-lubricating, check the engine oil level. If necessary, top off by
filling engine oil no more than 5.0 L (5.2 qt) at a time through the oil fill cap
to the satisfactory fill range on the oil dipstick. Do not overfill.
Checking and Monitoring the Oil Level
Check the oil level as follows:

NOTICE: Do not add oil if the oil reading is in the crosshatch area on the
dipstick. There are approximately 5.0 L (5.2 qt) from the fill mark to the full
mark. Overfilling the oil pan can cause engine damage.
NOTE: If the engine operating temperature is below 60C (140F), the
engine must be on a level surface and then shut down for 60 minutes for an
accurate oil level reading. Otherwise, the engine must be brought up to an
operating temperature of 60C (140F), parked on a level surface and then
shut down for five minutes for an accurate oil level reading.
37
1. Check the oil level daily with the engine stopped and on a level surface. If
the engine has just been stopped and is warm, wait approximately 20 minutes
to allow the oil to drain back into the oil pan before checking.
2. Add oil to maintain the correct level on the dipstick. Use only the heavy-duty
oils recommended in the "How to Replace the Lubricating Oil and Oil Filter"
section in this manual.
NOTE: The dipstick has a positive locking device such as a lever or twistlock design that must be disengaged before pulling the dipstick out of the
guide tube.
3. Remove the dipstick from the guide tube. Use a shop rag to wipe off the end
of the dipstick.
4. Wait 15 seconds to allow any crankcase pressure to dissipate through the
guide tube and let the oil level settle in the oil pan.
5. Reinstall the dipstick and make sure it is fully inserted into the guide tube.
6. Remove the dipstick and read the oil level dipstick.
7. The figure shows a comparison between the bends on the dipstick and a
crosshatch pattern on a conventional dipstick. Note the exact area noted on
the bends. For example, the 'maximum' oil level will be at the BOTTOM of
that bend. For the 'minimum' oil level, it is noted at the TOP of the bend. If
the oil level is below the 'minimum' bend, add oil to bring it up the
'maximum' level. Do NOT fill beyond the maximum fill level on the
dipstick, since overfilling may result in high oil consumption and possible
severe engine damage.
38
After an Extended Storage
NOTICE: Failure to eliminate water-diluted lubricating oil may lead to

serious engine damage at startup.
An engine in storage for an extended period of time (over winter, for example) may
accumulate water in the oil pan through normal condensation of moisture (always
present in the air) on the cold, internal surfaces of the engine.
Lubrication oil diluted by water cannot provide adequate bearing protection at
engine startup. For this reason, Detroit recommends replacing the engine
lubricating oil and filters after extended storage.
Fuel System Checks
Make sure the fuel shutoff valve (if used) is open. Fill the tanks with the
recommended fuel. Keeping tanks full reduces water condensation and helps keep
fuel cool, which is important to engine performance. Full tanks also reduce the
chance for microbe (black slime) growth. For fuel recommendations, Refer to
section "How to Select Diesel Fuel".
NOTICE: Prolonged use of the starting motor and engine fuel pumps to
prime the fuel system can result in damage to the starter, fuel pumps, and
injectors.
If the shutoff valve is even partially closed, it may cause erratic engine
operation due to an inadequate supply of fuel to the fuel pump.
NOTICE: NEVER use ether as a starting aid to run the engine. Doing so will
result in injector damage.
If an external starting aid is used, such as a starting fluid, the heat generated by the
external fuel source will cause the injector tips to be damaged when the fuel cools
them. The injector piston and bushing can be scored from running without
lubrication.
To ensure prompt starting and even running, the fuel system must be primed if air
has entered the fuel system. Priming is done by operating the manual hand priming
pump located on the fuel filter module or connecting an external priming pump to
the priming port on the fuel filter module.
Authorized Detroit service outlets are properly equipped for this type of service.
Priming is required if the fuel system has been serviced.
Drain off any water that has accumulated. Water in fuel can seriously affect engine
performance and may cause engine damage.
Adding Fuel
When adding fuel, pay attention to the following:

39
NOTICE: Always use Ultra-Low Sulfur Fuel (ULSF) with 15 PPM sulfur
content or less, based on ASTM Standard D2622 test procedure. Higher
sulfur levels will damage the engine Aftertreatment System (ATS).
Add winter or summer grade fuel according to the season of the year.
Work in the cleanest conditions possible.
Prevent water from entering the fuel tank.
For further information, Refer to section "How to Select Diesel Fuel".
Priming the Fuel System
Prime the fuel system as follows:

1. Operate the hand primer on module for three minutes or 250 strokes, or use
an external priming source such as tool J-47912 or ESOC 350.
2. Crank the engine for 20 seconds.
3. Wait 60 seconds for the starter to cool down.
4. If the engine does not start, repeat step 2 and step 3. The starting cycle can be
repeated up to three times.
5. If the engine still fails to start, continue as follows:
a. Use DDDL to check for fault codes, repair as necessary.
b. Repeat step 2 and step 3.
WARNING: ENGINE EXHAUST
To avoid injury from inhaling engine exhaust, always operate the
engine in a well-ventilated area. Engine exhaust is toxic.
To avoid injury before starting and running the engine, ensure the
vehicle is parked on a level surface, parking brake is set, and the
wheels are blocked.
NOTICE: If no oil pressure is shown after approximately 10 seconds, stop
the engine and determine the cause. Running the engine with no oil
pressure could result in engine damage.
6. Start the engine with the accelerator pedal in the idle position. Monitor the
oil pressure gauge or indicator lamp. Keep the engine running at idling
speed until the oil pressure reading is 14 psi (97 kPa) or more.
7. Allow engine to reach operating temperature 60C (140F).
NOTICE: Increasing engine speed above idle before oil pressure has
stabilized may cause severe engine damage.
8. Increase engine speed to 1800 rpm for three minutes.
40
9. Return the engine to idle and allow to idle for approximately one minute,
then shut down the engine.
10. Check for leaks. Repair if necessary.
Checking Other Engine and ATS Related Parts
Check the engine compartment as follows:
Make sure the transmission is filled to the proper level with the fluid
recommended by the gear manufacturer. Do not overfill.
The Diesel Exhaust Fluid (DEF) must be checked and filled regularly with DEF
meeting Detroit quality specification.
Make sure cable connections to the storage batteries are clean and tight.
Check for cracks in the battery cases (1), for tightness of the cable clamps (2) at
the terminals, and for corrosion of the terminals (3). Service or replace as
needed.
To provide corrosion protection, apply dielectric grease liberally to the terminal
pads.
Starting the Engine for the First Time

WARNING: EXPLOSION
To avoid injury from explosion, never use ether with an engine's
electrical cold starting system.
41
Before starting the engine the first time, perform an inspection of the engine
systems.
EPA07 engines only: An electrical grid heater is used as a cold weather starting
aid if the ambient temperature is below 4C (40F).
To start the engine, the transmission should be in neutral and the ignition key
turned to ON.
To avoid injury when working near or on an operating engine
equipped with an hydraulic clutch fan, remove loose items of
clothing and jewelry. Tie back or contain long hair that could be
caught in any moving part causing injury. The hydraulic fan may
start without warning.
You will notice that the Amber Warning Lamp (AWL), Red Stop Lamp (RSL),
Malfunction Indicator Lamp (MIL), Diesel Particulate Filter (DPF) Regeneration
lamp, and High Exhaust Temperature (HEST) lamp will come on. This is the result
of the DDEC computer diagnosing the system to ensure everything is functional,
including the light bulbs for the warning lights. If everything is OK, all lights will
go out in approximately five seconds.
The lights must go out before starting the engine. If starting a vehicle, the
operators foot must be OFF the accelerator pedal before starting the engine.
NOTICE: If the warning lights stay on, or do not come on momentarily after
turning on the ignition, contact the Detroit Customer Support Center at
1-800-445-1980. Operating the engine under these circumstances may
result in engine damage.
Starting the Engine

1. Place the transmission in neutral, and set the parking brake.
NOTICE: To prevent serious starter motor damage, release the ignition
switch immediately after the engine has started.
2. Turn on the ignition switch.
3. Wait for the engine system indicator lights on the instrument panel to go
out.
4. With foot off the accelerator pedal, start the engine.
42
5. If the engine does not start after 20 seconds, stop. Try again after waiting
about 60 seconds.
NOTICE: Do not increase engine speed if the oil pressure gauge indicates
no oil pressure. Shut down the engine within approximately ten seconds to
avoid engine damage. Check to determine the cause of the problem.
NOTE: Do not place the engine under full load until it reaches operating
temperature. Colder engine temperatures will cause the engine to preset
idle up to 900 rpm. Even at a high idle condition, you do not have to wait for
engine warm up and return to normal 600 rpm idle to drive the truck.
6. Monitor the oil pressure gauge immediately after starting the engine.
Running the Engine

While the engine is operating, monitor the battery charge indicator light, the oil
pressure, and avoid excessive idling.
Checking the Oil Pressure
Monitor the oil pressure as follows:
WARNING: HOT OIL
1. Observe the oil pressure gauge immediately after starting the engine. An oil
pressure gauge that registers pressure 14 psi (96 kPa) at idle speed and
normal operating temperature is a good indicator that all moving parts are
getting lubrication.
2. If no pressure is indicated within 10 to 15 seconds, stop the engine and check
the lubrication system at normal operating temperature.
3. The oil pressure should not drop below 55 psi (380 kPa) at 1800 rpm, at
normal operating temperature. If oil pressure does not fall within these
guidelines, check it with a manual gauge.
Warming Up the Engine
Run the engine at part throttle for about five minutes to allow it to warm up before
applying a load.
Inspection During Idling
While the engine is idling, inspect the transmission and crankcase for fluid leaks.
On DD15 and DD16 engines, check the Axial Power Turbine (APT) for oil leaks.
43
Checking the Transmission

While the engine is idling, check the automatic transmission (if equipped) for
proper oil level and add oil as required.
Checking for Fluid Leaks
Check for fluid leaks as follows:
1. Look for coolant, fuel, or lubricating oil leaks.
2. If any leaks are found, shut down the engine immediately and have the leaks
repaired after the engine has cooled.
Checking the Crankcase
Check the crankcase as follows:
1. If the engine oil was replaced, stop the engine after normal operating
temperature has been reached. Allow the oil to drain back into the crankcase
for about 60 minutes, then check the oil level.
NOTICE: Do not add oil if the oil reading is in the crosshatch area. There
are approximately 5.0 L (5.2 qt) from the fill mark to the full mark. Overfilling
the oil pan can cause engine damage.
2. If necessary, add no more oil than 5.0 L (5.2 qt) at a time to bring the level
to the proper mark on the dipstick. Use only the heavy-duty oils
recommended in the "How to Replace the Lubricating Oil and Oil Filter"
section in this manual.
44
Checking the Turbocharger

Check the turbocharger as follows:
1. Make a visual inspection of the turbocharger for oil leaks, exhaust leaks,
excessive noise, or vibration.
2. If a leak, unusual noise, or vibration is noted, stop the engine immediately.
Do not restart the engine until the cause of the concern has been
investigated and corrected.
Checking the Axial Power Turbine
Check the axial power turbine for excessive noise or vibration. Stop the engine
immediately if unusual noise or vibration is noted. Do not restart the engine until
the cause of the concern has been investigated and corrected.
Avoid Unnecessary Idling
Whenever possible, unnecessary idling should be avoided. During long engine
idling periods with the transmission in neutral, the engine coolant temperature may
fall below the normal operating range. The incomplete combustion of fuel in a cold
engine will cause crankcase oil dilution, formation of lacquer or gummy deposits
on the valves, pistons, and rings, and rapid accumulation of sludge in the engine.
When prolonged idling is necessary, maintain at least 900 rpm.
45
Stopping the Engine

Stop an engine under normal operating conditions as follows:
NOTICE: Do not stop a turbocharged engine immediately after a highspeed operation. Allow a sufficient cool-down period of about five minutes
to prevent the turbocharger from continuing to turn without an oil supply to
the bearings or damage can result.
1. Reduce engine speed to idle and put all shift levers in the neutral position.
NOTE: Cool-down idling needs to take place after pulling off an interstate.
When finding a parking spot or backing into a dock, immediate shutdown
should be avoided. Shutting the engine off immediately retains more block
heat than if the engine runs at idle for five minutes.
2. Allow the engine to run between idle and 1000 rpm with no load for five
minutes. This allows the engine to cool and permits the turbocharger to slow
down. After five minutes, shut down the engine.
Emergency Jump Starting

The engine's electronic system operates on 12 volts DC. If a DD Platform engine
with an electric starting motor requires emergency jump starting, DO NOT
EXCEED 16 VOLTS DC.
WARNING: BATTERY EXPLOSION
To avoid injury from battery explosion when jump starting the
engine, do not attach the cable end to the negative terminal of the
disabled battery.
battery acid:

NOTICE: Jump starting with voltages greater than those indicated or

reversing battery polarity may damage the MCM.
46
NOTICE: Failure to connect jumper cables in the proper sequence can

result in alternator and/or equipment damage.
Before attempting to jump start the engine, the jumper cables must be connected
properly; positive-to-positive, and negative-to-chassis or suitable ground. The
proper sequence is to connect negative to negative ground last.
Routine Engine Start

The following are procedures for a routine engine start.
To avoid injury when working near or on an operating engine
equipped with an hydraulic clutch fan, remove loose items of
clothing and jewelry. Tie back or contain long hair that could be
caught in any moving part causing injury. The hydraulic fan may
start without warning.
Routinely Starting the Engine

Before a routine start, see the daily checks for your engine in the Maintenance
section of this manual.
NOTICE: Before starting the engine, carefully read all operating instructions
in this manual and do all the recommended pre-trip inspections and daily
maintenance. Check the coolant, engine oil, and fuel levels, and drain
contaminants from the water separator/coalescer.
Start the engine as follows:
NOTE: If you drain water from the water separator/coalescer, you have to
prime the fuel system with the built-in hand primer (about 50 strokes).
NOTE: As a safety function, the electronic engine control system may be
wired to start the engine only if the transmission is in neutral. This feature is
vehicle application specific.
1.
2.
3.
4.
Turn on the ignition switch.

Wait for the engine system indicator lights on the instrument panel to go out.
With the accelerator pedal in the idle position, start the engine.
Check the engine for leaks.
47
a. Check all hoses, hose clamps, and pipe unions on the engine for
tightness. Shut down the engine and tighten them if necessary.
b. Check the oil feed and return lines at the turbocharger for leaks. Shut
down the engine and tighten them if necessary.
5. Shut down the engine.
6. Check the oil level using the oil dipstick. The oil level is measured using the
crosshatch area on the dipstick. If the oil reading within the crosshatch area,
then the oil is at the proper level for engine operation.
7. Check all the mounting fasteners on the engine for tightness.

Checking the Coolant Level (Cold Check)
Check coolant level as follows:
1. Ensure that all coolant plugs in the bottom of the radiator and on the radiator
outlet pipe are secure and tight.
2. Check the coolant level. The cooling system is correctly filled when the
coolant is between the full and low marks on the surge tank.
48
Checking the Coolant Level (Hot Check)

Check the coolant levels as follows:
1. Allow the engine to run for approximately five minutes at a moderate speed.
2. After the coolant temperature reaches 50C (122F), recheck the coolant
level in the surge tank.
3. Add more coolant if necessary. Open the heater valves before adding
coolant.
4. Do not close the heater valves until the engine has been running briefly and
the coolant level is again checked and corrected as necessary.
Monitoring the Engine Operation

While the engine is operating, monitor the battery charge indicator light and the oil
pressure. Excessive idling should be avoided.
Monitoring the Battery Charging System
The battery charge indicator light must go out once the engine starts. If the
indicator light comes on while the engine is running, do the following:
1. Shut down the engine.
2. Test the charging system, per OEM guidelines.
WARNING: BATTERY EXPLOSION
To avoid injury from battery explosion when jump starting the
engine, do not attach the cable end to the negative terminal of the
disabled battery.
3. If necessary, visit the nearest authorized dealer to have the alternator voltage
and output checked.
4. Do a load test on the batteries.
5. Replace components as needed.
Monitoring the Oil Pressure
When the engine has reached its normal operating temperature, the engine oil
pressure must not drop below the following values:
49
55 psi (380 kPa) at rated speed

14 psi (97 kPa) at idling speed
If oil pressure drops below these values, stop the engine and determine the cause.
Excessive Idling
Never allow the engine to idle for more than 30 minutes. Excessive idling can
cause oil to leak from the turbocharger.
Changing the Idle Speed

The idle speed range of the DD Platform engine is 600 to 900 rpm if the parameters
in the CPC are set to the default range. Change the idle speed as follows:
1. Turn the cruise control switch to the ON position.
2. To increase the idle speed, push the RSM/ACC switch until the idle reaches
the desired rpm.
3. To decrease the idle speed, push the SET/CST switch until the idle reaches
the desired rpm.
Shutting Down the Engine after High Load Operation

If the engine has been running at full output or the coolant temperature has been
high, idle the engine for five minutes without load. If any of the following
conditions occur, shut down the engine immediately:
NOTICE: A engine running at full output or with high coolant temperature
after a high load operation should idle for five minutes without load. Shutting
down without idling may cause damage to the turbocharger.
The oil pressure swings back and forth or falls sharply.

Engine power and rpm fall, even though the accelerator pedal remains steady.
The exhaust pipe gives off heavy smoke.
The coolant and/or oil temperature climb abnormally.
Abnormal sounds suddenly occur in the engine or turbocharger.
Emergency Running Mode

The engine is equipped with an electronic motor control system which monitors the
engine as it is running.
NOTICE: To prevent possible serious engine damage, have any faults
corrected without delay by an authorized service location.
As soon as an engine fault is detected, it is evaluated and one of the following
measures is initiated.
50
In conjunction with any dashboard or instrument panel display, the code for the
electronic control unit reporting the fault can be read immediately on the display.
If the fault is serious enough to impair normal operation, the electronic control
unit switches over to a "limp home" mode. The limp home speed is dependent on
engine control parameters and could be as low as 1000 rpm. This allows you to
safely move the vehicle to a service location or a safe stopping area.
Stop Engine Override Option

The Stop Engine Override Option is used for a momentary override. The electronic
engine control system will record the number of times the override is activated after
an engine fault occurs.
Momentary Override
A Stop Engine Override Switch is used to override the shutdown sequence. This
override resets the 60 second (30 second for oil pressure) shutdown timer, restoring
power to the level when the RSL/Stop Engine was illuminated. The switch must be
recycled after five seconds to obtain a subsequent override.
NOTE: The operator has the responsibility to take action to avoid engine
damage.
51
Cold Weather Operation

Special precautions must be taken during cold weather. To protect your engine,
special cold weather handling is required for fuel, engine oil, coolant, and batteries.
NOTICE: To avoid engine damage, DO NOT use any type of aerosol spray,
e.g., ether, starting fluid or brake cleaner to aid in starting the engine.
For EPA07 engines with a grid heater:
WARNING: BODILY INJURY
To avoid injury from an explosion, do not use ether or starting
fluid on engines equipped with a manifold (grid) heater.
The engine does not require starting aids down to 10C (50F). Temperatures
below -20C (-4F), will require a block heater and oil pan heater.
Winter Fronts
Winter fronts on DD engines are seldom necessary due to the modern design of the
engine cooling system. The coolant thermostat is on the inlet side of the cooling
system on the DD Platform engine and regulates coolant flow from the radiator into
the engine. The thermostat regulates coolant flow to control the temperature of the
coolant within the coolant circuit. The following benefits are a result from
regulating the coolant at the inlet temperature side of the engine:
Reduced thermal cycling of the engine
Operating temperature is reached faster
Improved vehicle heating because of better temperature regulation
Further information on the thermostat function may be found in the Coolant
Thermostat section of the EPA07/10/GHG14 Engine Manual (DDC-SVCMAN-0081).
Use of a winter front on a DD Platform engine, particularly those that are fully
closed, will cause performance issues and is not recommended on DD Platform
engines. Winter fronts can result in the following:
Excessive fan run time due to higher Charge Air Cooler (CAC) outlet
temperatures resulting from low air flow through the CAC
Increased fuel consumption
Failure of the DEF system heaters to turn on when needed due to incorrect
temperature calculations resulting in fault codes, poor performance of the
Aftertreatment System, and power reduction
Failure of critical emission equipment that will result in vehicle speed
inducement to a maximum of 5 mph
Use of a winter front should be avoided as this has been shown to cause false fault
codes with the engine and aftertreatment system. This has also been linked to
specific component failures that will cause vehicle downtime and lost productivity.
There are two specific situations where a winter front may be temporarily needed:
52
To improve cab heating while idling under extreme cold ambient temperature
When the ambient temperature remains below -30C (-22F) and the engine is
unable to maintain running coolant temperature of 80C (175F) during normal
over-the-road operation
If either of the above situations is encountered, then a winter front may be
temporarily used. A minimum of 25% of the grill must be open in sectioned stripes
that run perpendicular to the charge air cooler tube flow direction. This assures
even cooling across each tube and reduces header-to-tube stress and possible
failure.
53
Detroit Diesel Electronic Controls (DDEC) System

DDEC VI System - EPA07
The engine is equipped with a fully electronic control system, which regulates the
fuel injection quantity and timing using solenoid valves, allowing extremely lowemission operation. Besides the engine and its related sensors, the system is
composed of the following:
The Motor Control Module (MCM)
The Common Powertrain Controller (CPC) located under the right-hand dash
panel.
The two control units are connected by a proprietary datalink through which all
necessary data and information can be exchanged.
The CPC then broadcasts all information on the J1587 and J1939 datalinks, where
it can be read by the diagnostic tool.
The engine control system monitors both the engine and the datalink. When a
malfunction or other problem is detected, the system selects an appropriate
response; for example, the emergency running mode may be activated.
The Accelerator Pedal Assembly (AP) eliminates the need for any throttle
linkage.
Motor Control Module Description - EPA07

The Motor Control Module (MCM) is typically located on the left-hand side of the
engine.
Figure 21. Motor Control Module - EPA07

The MCM processes the data received from the Common Powertrain Controller
(CPC), for example the position of the Accelerator Pedal (AP), engine brake, etc.
54
These data are evaluated together with the data from the sensors on the engine,
such as coolant and fuel temperature and oil and charge pressure. The data is then
compared to the characteristic maps or lines stored in the MCM. From these data,
quantity and timing of injection are calculated.
NOTE: To obtain a replacement MCM, all the data given on the MCM label
are required.
The MCM data label has the 10 digit engine serial number.
Engine Emissions Certification Label

All Detroit engines complies with all United States Environmental Protection
Agency (U.S. EPA) and California Air Resources Board (CARB) emission
standards. An emission label is attached to the cylinder head cover, as required by
law.
NOTE: The horsepower rating on the emission label is for the highest
engine rating and not necessarily the rating of your engine.
55
Figure 23. Engine Emission Label - EPA07

NOTE: Examples are shown as EPA07. Each EPA10, GHG14 and GHG17
unit will have a similar label with the same information.
Common Powertrain Controller

The Common Powertrain Controller (CPC) communicates with any other Motor
Control Module (MCM) unit installed on the vehicle over the J1939 data link.
Data for specific applications is stored in the CPC. These include idle speed,
maximum running speed, and speed limitation. From these data, instructions are
computed for controlling the engine and transmitted to the CPC via the proprietary
datalink.
The CPC receives data from the following sources:
The operator (accelerator pedal position, engine brake switch)
Other electronic control units (for example, the anti-lock brake system)
The MCM (oil pressure and coolant temperature)
56
1. Connector 1
2. Connector 2
3. Connector 3
4. Connector 4
Figure 24. Common Powertrain Controller
DDEC 10 System - EPA10/GHG14

All engines for 2010 are equipped with an electronic control system called Detroit
Diesel Electronic Control (DDEC10). The electronic engine control system
regulates the fuel injection quantity and timing using solenoid valves, allowing
extremely low-emission operation. Besides the engine and its related sensors, the
system has three other control modules:
Common Powertrain Controller (CPC)
Aftertreatment Control Module (ACM)
The three control units are connected by a proprietary datalink through which all
necessary data and information can be exchanged. EPA10 and GHG14 units
operate on the same hardware.
The MCM monitors both the engine and the datalink. When a malfunction or other
problem is detected, the system selects an appropriate response; for example, the
emergency running mode may be activated.
The MCM processes the data received from the CPC, for example, the position
of the accelerator pedal and engine brake.
This data is evaluated together with the data from the sensors on the engine, such
as coolant and fuel temperature and oil and charge pressure. The data is then
compared to the characteristic maps or lines stored in the MCM. From this data,
57
The CPC broadcasts all information on datalinks. A certified service center

technician can access the CPC via the datalink using the Detroit Diesel Diagnostic
Link (DDDL) electronic diagnostic tool.
The CPC communicates with the MCM unit installed on the vehicle over the
proprietary datalink.
Data for specific applications is stored in the CPC. Examples include idle speed,
maximum running speed, and speed limitation.
The CPC receives data from several sources. Examples include:
Accelerator pedal position, engine brake switch
Anti-lock brake system and other electronic control units
Oil pressure, coolant temperature and others, from the MCM
From this data, instructions are computed for controlling the engine and transmitted
to the CPC via the proprietary datalink. The ACM monitors the Aftertreatment
System (ATS). When a malfunction or other problem is detected, the system selects
an appropriate response to deliver to the operator.
Motor Control Module Description - EPA10

The Motor Control Module (MCM2) is typically located on the left-hand side of
the engine.
1. Connector 1
2. Connector 2
Figure 25. Motor Control Module 2- EPA10

The MCM processes the data received from the Common Powertrain Controller
(CPC), for example the position of the Accelerator Pedal (AP), engine brake, etc.
These data are evaluated together with the data from the sensors on the engine,
such as coolant and fuel temperature and oil and charge pressure. The data is then
compared to the characteristic maps or lines stored in the MCM. From these data,
58
NOTE: To obtain a replacement MCM, all the data given on the MCM label
are required.
The MCM data label has the 10 digit engine serial number.
Common Powertrain Controller

The Common Powertrain Controller (CPC) communicates with any other Motor
Control Module (MCM) unit installed on the vehicle over the J1939 data link.
Data for specific applications is stored in the CPC. These include idle speed,
maximum running speed, and speed limitation. From these data, instructions are
computed for controlling the engine and transmitted to the CPC via the proprietary
datalink.
The CPC receives data from the following sources:
The operator (accelerator pedal position, engine brake switch)
Other electronic control units (for example, the anti-lock brake system)
The MCM (oil pressure and coolant temperature)
59
1. Connector 1
2. Connector 2
3. Connector 3
4. Connector 4
Figure 27. Common Powertrain Controller
Detroit Diesel Electronic Control System Operation

NOTE: This engine is equipped with DDEC software. This software
generally assures optimal engine performance. The installation of software
upgrades may cause minor changes in features and engine performance.
Since the DDEC system is electronic, a battery is required to operate the computer.
The system operates at 12 volts. However, in the event of a power supply
malfunction, the system will continue to operate at reduced voltage. When this
occurs, the AWL (Check Engine) will come on.
60
The engine will only operate at reduced rpm until the battery voltage reaches a
point where the MCM will no longer function and the engine shuts down.
Should the AWL (Check Engine) come on for any reason, the vehicle can still be
operated and the driver can proceed to the required destination. This condition
should be reported to an authorized Detroit distributor or dealer.
NOTICE: When the RSL (Stop Engine) comes on, the system has detected
a major malfunction in the engine that requires immediate attention. It is
the operator's responsibility to shut down the engine to avoid serious
damage.
The engine can be configured to give a warning only, to ramp down (reduce power)
or to shut down. Ramp down will reduce engine rpm to a predetermined speed, but
will not shut down the engine. With the 30-second shutdown option, the engine will
begin a 30-second, stepped power down sequence until it shuts down completely.
The "Stop Engine Override" feature can be activated in the case where the vehicle
is operating in a critical location.
Stop Engine Override Switch

This feature allows the operator to override the automatic stop engine sequence.
This is done by pressing the Stop Engine Override Switch every 15 to 20 seconds
to prevent engine shutdown from occurring.
61
NOTE: The Stop Engine Override Switch and the Diagnostic Request
Switch (EPA07 function only) are the same.
NOTE: Holding down the Stop Engine Override Switch will not prevent the
engine shutdown sequence. You must continue to reset the automatic
shutdown system by pressing the Stop Engine Override Switch at intervals
of approximately 15 to 20 seconds.
It takes 30 seconds from the time the automatic shutdown sequence begins until
engine shutdown. Therefore, the operator must press the override switch just prior
to engine shutdown and continue to do so until the vehicle can be brought to a stop
in a safe location.
Immediate Speed Reduction

The immediate speed reduction option will bring engine rpm back to a
predetermined speed, but will not shut down the engine.
The engine should not be restarted after it has been shut down by the engine
protection system, unless the problem has been located and corrected.
Red Stop Lamp

The conditions that will cause the RSL (Stop Engine) to come on are:
High coolant temperature

Loss of coolant
High oil temperature
Low oil pressure
Auxiliary shutdown
Whenever the AWL (Check Engine) or the RSL comes on, the DDEC 10 system
will determine where the problem is and will then store this information in its
memory.
If the malfunction is intermittent, the lights will come on and go off as the
computer senses the changing engine condition.
Diagnostic Tool
The diagnostic tool for Detroit Diesel Electronic Control (DDEC 10 and newer) is
the DiagnosticLink 8.x. DiagnosticLink requirements are listed earlier in the
manual under Data Recording Capability.
Once the malfunction has been corrected, the DDEC system will return the engine
to normal operation.
The air temperature in the intake system is increased with the addition of EGR.
DDEC is programmed to reduce fueling (power) for a short time to reduce air and
coolant temperatures when necessary.
62
DDEC will store an information code when this event occurs, but no corrective
action is required. This action is designed to maintain operation without a
noticeable effect on vehicle performance.
Flashing Malfunction Codes
NOTE: EPA07 only function.
All malfunction codes are four digits. The malfunction code recorded in the
computer memory will remain until it is erased by a technician.
The flashing malfunction code can also be obtained by the operator. To support
flashing codes, a Stop Engine Override/Diagnostic Request Switch must be
configured and the AWL (Check Engine) and RSL (Stop Engine) must be hardwired. The CPC cannot flash these lamps if they are not hard-wired.
The flashing code feature may be activated by satisfying one of the following
conditions:
Engine speed is less than 100 rpm and the Stop Engine Override Switch is put in
the ON position.
Idle Governor is active and the Stop Engine Override Switch is put in the ON
position.
Vehicle speed is less than three mph. Parking Brake is activated and the Stop
Engine Override Switch is put in the ON position.
The flashing code feature is deactivated once the Stop Engine Override Switch is
returned to the OFF position or the listed conditions are no longer satisfied.
Only one light will be flashing codes at any time. All codes will be flashed twice.
The inter-digit pause is 1.5 seconds. The pause between codes is 3.5 seconds. The
same 3.5-second pause occurs as the switch is made from RSL (Stop Engine) to
AWL (Check Engine).
When code flashing is initiated, the active codes will be flashed on the RSL (Stop
Engine). Then the inactive codes will be flashed on the AWL (Check Engine).
When all the inactive codes have been flashed, the process of flashing all the active
codes followed by all the inactive codes will repeat until the conditions for code
flashing are no longer satisfied.
If there are no active or inactive faults, the number 3 is flashed once followed by a
gap of three seconds.
63
NOTE: EPA10 and newer can be outfitted with an OEM smart dash which
does not require driver interaction to display malfunction lamps. Malfunction
lamps will display across the information screen if equipped.
Reading Fault Codes
NOTE: EPA07 only function.
To read the fault codes, press and hold the Stop Engine Override / Diagnostic
Request Switch.
Active codes will be flashed on the RSL (Stop Engine) first, followed by inactive
codes being flashed on the AWL (Check Engine). The codes will continue to flash
and repeat as long as the Diagnostic Request Switch is held in the ON position.
Both CPC and MCM faults are included.
Active Codes
The active codes will be flashed on the RSL (Stop Engine) in the order of most
recent to least recent occurrence based on engine hours.
Inactive Codes
The inactive codes will be flashed on the AWL (Check Engine) in the order of most
recent to least recent occurrence based on engine hours.
Detroit Diesel Electronic Control System Features

The electronic engine control system offers a variety of features and options
designed to warn the operator of any engine or Aftertreatment System (ATS)
malfunction. Options can range from warning panel lights to automatic reduction in
engine power followed by automatic engine shutdown. The electronic engine
control system has the ability to perform diagnostics for self-checks and
continuous monitoring of other system components.
64
Depending on the application, the electronic engine control system can monitor oil
temperature, coolant temperature, oil pressure, fuel pressure, coolant level and
remote sensors (if used).
The electronic engine control system activates the Amber Warning Lamp (AWL) /
Check Engine and the Red Stop Lamp (RSL) / Stop Engine to provide a visual
warning of a system malfunction.
Data Recording Capability

The electronic engine control system (DDEC 10 and newer) has the ability to
extract detailed data on engine use and performance using DDEC Reports software.
This detailed data (or DDEC Data) is stored in the CPC and contains information
on engine performance such as fuel economy, idle time, and time in top gear.
Critical incidents such as detailed diagnostic data records and hard braking events
are also stored. DDEC Data can be downloaded using DDEC Reports software to
produce reports.
NOTE: As the diagnostic and reprogramming software applications have
evolved, the requirements for additional computer storage capacity and
memory have increased. Please review these computer specifications
carefully and take any necessary steps to update your hardware as needed.
DiagnosticLink 8.0 Minimum System Requirements:
IT Security Firewall Access for TCP Port 48481
Windows XP SP2, Windows Vista SP2, Windows 7, Windows 8, 32- and 64-bit
(please note: some Access Freightliner applications do not support Windows 8)
2.0 GHz Dual-Core processor or greater
2 GB RAM or more
40 GB hard drive with 20 GB free space
Monitor and graphics card supporting 1024 x 768 resolution
1 free USB port
High Speed Internet - Broadband Internet
Nexiq USB-Link with USB cable (required for Cascadia diagnostics)
Administrative Rights (for installation only)
Minimum System Requirements:
2 GB RAM or more
1 free USB port
DiagnosticLink 8.0 Minimum System Requirements:
65

2 GB RAM or more
1 free USB port
NOTE:
DiagnosticLink 8.X is backwards compatible with DDEC VI units.
Engine Brake
The engine brake is enabled by a dash-mounted ON/OFF Switch with a separate
intensity switch to select low, medium, or high braking power.
trailer.
The engine brake will only operate when the Accelerator Pedal is fully released.
Disengaging the clutch will prevent the engine brake from operating.
The engine brake will supply braking power even when in Cruise Control. The
Motor Control Module will control the amount of engine braking with respect to
the Cruise Control set speed. The maximum amount of braking (low, medium,
high) is selected with the dash or steering wheel switches.
Engine Protection
The electronic engine control protection system monitors all engine sensors,
electronic components, and recognizes system malfunctions. If a critical fault is
detected, the AWL (Check Engine) and RSL (Stop Engine) illuminate. The
malfunction codes are logged into the MCM's memory.
66
The standard parameters which are monitored for engine protection are low coolant
level, high coolant temperature, low oil pressure, and high oil temperature.
To avoid injury from engine shutdown in an unsafe situation,
ensure the operator knows how to override the stop engine
condition on a DDEC-equipped unit.
NOTICE: Engines equipped with the power down/shutdown option have a
system override button or switch to allow engine operation for a short period
of time. Using the override button so the engine does not shut down in 30
seconds but operates for an extended period may result in engine damage.
This system features a 30-second, stepped-power shutdown sequence, or an
immediate speed reduction without shutdown in the event a major engine
malfunction occurs, such as low oil pressure, high oil or coolant temperature, or
low coolant level.
California Engine Idle Limiting

All 2010 and newer Detroit engines built with the California (50-state) EPA
certification are allowed to idle indefinitely when idle speed is below 900 rpm.
For California (50-state) EPA certification engines that idle above 900 rpm, the
California Engine Idle Limiting feature is enabled. The engine will generally shut
down after five minutes of continuous idling when the transmission is in neutral or
park and the parking brake is set or after 15 minutes when the transmission is in
neutral or park and the parking brake is not set. The automatic shutdown feature
that is applied above 900 rpm is required for all California certified engines with
the exception of engines used in specific vehicle types which the state of California
has determined to be exempt from the idle shutdown requirement. These include
buses, school buses, recreational vehicles, medium duty vehicles, military tactical
vehicles, and authorized emergency vehicles as they are defined by the state of
California. Owners of these vehicle types that wish to have the shutdown feature
disabled should consult with California authorities to determine if their vehicles
qualify for the exemption.
Non-California (49-state) EPA certification engines (non-California engines) have
the automatic shutdown feature enabled.
In California and Opt-in states, extended idling above 900 rpm is not allowed
unless the engine is performing a parked DPF regeneration or engaged in PTO
operations such as pumping, hydraulics, etc.
67
Idle Shutdown Timer

This feature is an optional 1-80 minute idle shutdown system. Its purpose is to
conserve fuel by eliminating excessive idling and allowing a turbocharger cooldown period. To activate the shutdown, the transmission must be in neutral with the
vehicle parking brakes set and the engine in idle or fast-idle mode.
Accelerating the Vehicle

Engine response versus pedal movement may feel different from the mechanicalgoverned engine you were driving. The Accelerator Pedal (AP) was designed to
communicate 'percentage' foot pedal travel to the engine's Motor Control Module
(MCM). The engine will respond accordingly to the driver's demand.
Another throttle or governor characteristic you may need time to get used to is the
DDEC Limiting Speed Governor. This allows the driver to command total engine
response between idle and rated speed, such as accelerating at half throttle - an
advantage when driving under slippery conditions.
If you require wide-open throttle engine response, either accelerating or just plain
pulling hard, the throttle AP will have to be held to the floor. To obtain 100%
fueling at any speed, the AP will have to be maintained at the fully pressed
position.
Cruise Control
For added driver convenience and comfort, DDEC also features a Cruise Control
option that works just like the system in your car. It can be operated in any gear
above 1100 rpm or road speed faster than 20 mph (32 kph), up to the rated engine
speed. It also can be programmed to hold your road speed at or below the
maximum vehicle speed. The switch to energize Cruise Control is usually mounted
on the instrument panel or steering wheel.
68
Engine speed and power are varied under Cruise Control to maintain the set vehicle
speed. The vehicle speed must be above Min Cruise Set Speed and below Max
Cruise Set Speed. It is recommended that Max Cruise Set Speed be set to the
default to allow proper operation of other features such as Fuel Economy Incentive
and PasSmart. The Vehicle Speed Limit should be used to limit vehicle throttle
speed.
Turn the switch ON to energize the system. Remember as a check after each engine
start, DDEC looks for a one-time activation of the clutch (if equipped) and service
brake before DDEC allows Cruise Control to be enabled.
DDEC must also see or recognize that the Cruise Enable Switch has changed. If the
Cruise Enable Switch is OFF it needs to be turned ON. If the Cruise Enable Switch
is left in the ON position at key OFF, the switch must be cycled OFF then ON for
DDEC to see a status change to allow Cruise Control activation. The status of
DDEC inputs to activate Cruise Control at key ON is listed in the following table.
Table 2.
Input Status to Activate Cruise Control
Input
Input Status at Key ON
Input Status Before Cruise

Control Activates
Service Brake Switch
ON
OFF
Clutch Release Switch

(Manual Trans. only)
ON
OFF
Cruise Control Enable Switch
OFF
ON
69
Once Cruise Control is enabled and you reach your road speed, press the SET
Switch to activate Cruise Control. The cruise light will come on. To increase road
speed toggling the switch will result in a one mile-per-hour (1.6 kph) increase or
decrease in vehicle speed. If Cruise Control has been disabled, toggling the
RSM/ACC Switch restores the vehicle to the previously set cruise speed. , press the
RSM/ACC Switch. To reduce road speed, press and hold the SET/CST Switch until
the lower speed is reached.
Cruise Control can be overridden at any time with the throttle pedal if the vehicle is
operating at less than the programmed Max Road Speed.
Cruise Control is deactivated by slightly pressing the service brakes, clutch pedal,
or trailer brake. The ON/OFF Switch will also deactivate Cruise Control.
Cruise Control will maintain vehicle speed even on upgrades, unless power
requirements demand a downshift. If the Cruise Control/Engine Brake function is
turned ON, the Cruise Control will limit your speed on downgrades. Most likely,
Cruise Control will feel stronger than driving with the accelerator pedal because of
the instantaneous and wide-open throttle response. That's why Cruise Control use is
not suggested during slippery driving conditions.
Use Cruise Control after downshifting on a hill to pull the hill. Hitting the
RSM/ACC Switch (not the SET Switch) will keep the truck accelerating in the
lower gears up to the rated engine speed.
To avoid injury from the loss of vehicle control, do not use cruise
control under these conditions:
When it is not possible to keep the vehicle at a constant speed
(on winding roads, in heavy traffic, in traffic that varies in
speed, etc.).
On slippery roads (wet pavement, ice-or snow-covered roads,
loose gravel, etc.).
Cruise Control will maintain the set speed under normal road and load conditions.
It cannot limit vehicle speeds on down grades if available engine braking effort is
exceeded, nor can it maintain speed on upgrades if power requirements exceed
engine power capability.
Cruise Control will disengage below 1000 rpm or 20 mph (32 kph) road speed.
When using Cruise Control, if you want to pull the engine below 1000 rpm,
remember to hold the accelerator pedal to the floor to keep the engine pulling at
wide-open throttle. The engine will pull down to about 1050 rpm.
Remember:The electronic data programmed into the DDEC system will not allow
you to hurt or over fuel the engine at low or lug engine speeds. There is enough oil
pressure to withstand hard pulls at low engine speeds.
Cruise Control may also be programmed to permit fast idle using the Cruise
Control switches.
70
With the engine at normal idle, transmission in neutral and service brakes on, press
the SPD CNTL Switch, and use the RSM/ACC Switch. The engine rpm should
increase to a pre-defined speed. The engine rpm can be raised or lowered from this
point using the SET/CST and RSM/ACC switches.
Engine Brake and Cruise Control

Your engine is equipped with both Cruise Control and an engine brake; the engine
brake can operate automatically while you are in Cruise Control. If the Cruise
Control/Engine Brake function is turned ON in the DDEC system programming,
the engine brake will come on low when your set road speed increases a few mph
(kph) above your cruise set speed. If your speed continues to increase, the DDEC
system will increase the engine brake's braking power progressively. When the
vehicle returns to the set cruise speed the engine brake will turn off until you need
them.
For safety reasons, don't use Cruise Control when it is not possible to keep the
vehicle at constant speed due to:
Winding roads
Heavy traffic
Slippery pavement
Descending grades calling for engine brake assistance
For an explanation of the engine brake system and recommendations for proper
operation, "Engine Brake System" in this manual.
DD Platform Shifting
Depending on your transmission model, the gear split may vary from 400 to 500
rpm. The electronic governor provides almost no overrun capability; and, if the
transmission is downshifted too early, you will experience a temporary loss of
pulling power until the engine speed falls below rated speed.
In general, when using a 7- or 9-speed transmission, you should always downshift
between 1150 and 1250 rpm for the DD13 and between 1000 and 1100 rpm for the
DD15 and DD16. This is true even on steep grades with heavy loads. When using
an 18-, 15-, or 13-speed transmission, you will need to downshift at an rpm that
allows "less than rated" rpm before throttle application in the next gear down. You
may want to limit engine speed to 1900 rpm in all gears. DD Platform engines
provide horsepower through 2100 rpm, but fuel economy is not as efficient above
1800 rpm.
If you decide to drive at a lower rpm for improved fuel economy, dont let different
engine noises throw you off guard. The engine sounds quiet at 1400 rpm, almost as
if it had quit pulling. Depending on the air intake arrangement, you may also
experience a "chuffing" sound as the engine starts to pull hard at lower rpm. This is
71
normal and caused by the velocity changes of the air flow within the air intake
plumbing. Electronic engines can actually deliver more fuel at lower engine speeds
than at rated speed.
The engine has been designed for a very quiet operation, but the air flow may be
noticeable to the tuned, attentive ear. The turbocharger operates at higher boost
pressure forcing EGR gas flow through the EGR plumbing. In some situations the
driver may believe he/she has experienced a charge air cooler system leak. Even
connecting trailer light and air hoses, the driver may hear a different tone (exhaust
and under hood with the engine idling.) If equipped with a turbo boost gauge, the
driver may occasionally note intake manifold pressure exceeds 35 psi (6.89 kPa).
Idling
The common belief that idling a diesel engine causes no engine damage is wrong.
Idling produces sulfuric acid, which is absorbed by the lubricating oil and eats into
bearings, rings, valve stems and engine surfaces. If you must idle the engine for cab
heat or cooling, the high idle function of the Cruise Control switches should be
used. An idle speed of 900 rpm should be enough to provide cab heat in above 0C
(32F) temperatures.
72
Engine Brake System

The engine is equipped with an engine brake. Before operating the vehicle, you
must familiarize yourself with the engine brake system to obtain optimum benefit
from it. Engine brake control systems may vary slightly, depending on the engine
brake configuration and cab design. However, basic operator controls are similar
for all models.
Driver Control Switches

Vehicles with manual transmissions allow the driver to turn the engine brake on
and off and select a Low, Medium, or High level of braking.
EPA07 Engine
The "Low" setting on this switch activates braking on two cylinders, yielding
about one-third engine braking horsepower.
The "Medium" setting on this switch activates four cylinders, supplying about
two-thirds engine braking horsepower.
The "High" setting on this switch activates all six cylinders, providing full
engine brake horsepower.
EPA10/GHG14/GHG17 Engine
The "Low" setting on this switch activates braking on three cylinders, yielding
about one-third engine braking horsepower.
The "Medium" setting on the switch activates all six cylinders, supplying about
two thirds engine braking horsepower.
The "High" setting on the switch activates all six cylinders, supplying full engine
brake horsepower.
NOTE: There is very little difference in the exhaust sound when the EPA10/
GHG14/GHG17 engine brakes are activated in either the medium or high
position. The GHG17 platform engines will experience slightly different
engine brake logic provided by enhancements within CPC software.
Clutch Pedal and Throttle Position Controls

Engine brakes have two additional controls, one activated by the position of the
clutch pedal and the other activated by the position of the throttle. These controls
permit fully automatic operation of the engine braking system.
Engine Brake Activation Conditions

The engine braking system only permits fully automatic operation when the
following conditions are met:
73
Engine Brake System
Engine Brake switch is on.

An Engine Brake level (Low/Med/High) is selected.
Vehicle meets the programmed minimum speed.
The Clutch Pedal is out.
The Accelerator Pedal is at zero percent activation.
Engine Brake Operation

NOTICE: Always allow the engine to reach full normal operating
temperature before activating the engine brake system to ensure positive
engine brake engagement.
The engine brake system depends on a full-pressure flow of warm engine
lubricating oil for proper lubrication of moving parts and optimum performance.
The minimum operating speed for the engine brake is 900 rpm. A check engine
lamp will be illuminated when the operating speed exceeds 2200 to 2300 rpm
depending on engine configuration.
NOTICE: Never exceed 2500 rpm or extensive engine damage can occur.
trailer.
Under normal driving conditions the engine brake system is left in the ON position.
However, this should change if roads become wet or slippery.
NOTICE: Do not attempt to double clutch the transmission while the
engine brake system is turned on. Shifting gears without pressing the clutch
or using the engine brake to reduce engine rpm may result in serious
powertrain damage.
After it is switched on, the engine brake system is automatically activated each time
you remove your feet completely from the clutch pedal and accelerator pedal. The
engine brake automatically deactivates itself when you press the clutch pedal while
shifting gears.
74
NOTE: Some systems may be programmed to activate themselves only

when the brake pedal is pressed, so read your vehicle owner's manual
thoroughly to find out if you have this option.
Anti-Lock Braking Systems

Vehicles equipped with ABS have the ability to turn the engine brake OFF if a
wheel-slip condition is detected. The engine brake will automatically turn itself ON
once the wheel slip is no longer detected.
The DDEC system will deactivate the engine brake system when the engine speed
falls below a preset rpm or when the vehicle slows down to a preset speed,
depending on DDEC programming. This prevents stalling the engine. The engine
brake can also be used with vehicle Cruise Control turned ON.
Operating on Flat, Dry Pavement

Use the following guidelines when driving on flat, dry pavement:
If driving on flat, dry, open stretches with a light load and greater slowing power
is not required, place the progressive braking switch in the LOW position.
If you find you are still using the service brakes, move the progressive braking
switch to a higher position until you do not need to use the service brakes to slow
the vehicle down.
If you are carrying a heavier load and road traction is good, move the progressive
braking switch to the HIGH position.
Check your progressive braking switch often for proper position, since road
conditions can change quickly. Never skip a step when operating the progressive
braking switch. Always go from OFF to LOW, and then to a higher position.
Operating Down a Long, Steep Grade

An explanation of speed; may be helpful in understanding how to use the engine
brake system while descending a grade. Control Speed is the constant speed at
which the forces pushing the vehicle forward on a grade are equal to the forces
holding it back, without using the vehicle service brakes. In other words, this is the
speed the vehicle will maintain without using the service brakes or fueling.
NOTICE: Failure to keep the vehicle within safe control speed limits while
descending a grade may result in vehicle or property damage or both.
Use the following guidelines when descending a long, steep grade:
1. Before beginning the descent, determine if your engine brake system is
operating properly by lifting your foot briefly off the accelerator pedal. You
should feel the system activate.
75
Engine Brake System
CAUTION: BRAKE FADE

To avoid injury, do not over apply the vehicle service brakes
when descending a long, steep grade. Excessive use of the
vehicle brakes will cause them to heat up, reducing their stopping
ability. This condition, referred to as brake fade, may result in
loss of braking, which could lead to personal injury or vehicle/
property damage or both.
2. Ensure the progressive braking switch is in the appropriate power position
(LOW/MED/HIGH).
Failure to keep the vehicle within safe control speed limits while
descending a grade may result in loss of vehicle control, which
could cause personal injury.
3. Do not exceed the safe control speed of your vehicle. Example: You could
descend a 6% grade, under control only at 10 mph (16 kph) without an
engine brake, but at 25 mph (40 kph) with an engine brake. You could not
descend that same hill at 50 mph (80 kph) and still expect to remain under
control. Get to know how much slowing power your engine brake can
provide. So get to know your engine brake system before climbing hills and
do not exceed a safe control speed.
4. Check your progressive braking switch often for proper position
(LOW/MED/HIGH), since road conditions can change quickly. Never skip a
step when operating the progressive braking switch. Always go from OFF to
LOW and then to a higher position when on slippery roads.
Operating on Wet or Slippery Pavement

Operate the engine brake system as follows:
NOTE: Experience with the engine brake system on dry pavement is
recommended before attempting to use it on wet or slippery roads.
1. On wet or slippery pavement, start with the master switch in the OFF position
and use the gear you would normally use under these conditions.
76

trailer.
NOTE: On single trailers or combinations, a light air application of the trailer
brakes may be desirable to help keep the trailer stretched out. Follow the
manufacturer's recommended operating procedure when using your trailer
brakes.
2. If the tractor drive wheels begin to lock or there is fishtail motion after the
Engine Brake is activated, deactivate the brake system immediately if this
occurs.
3. However, if the tractor drive wheels begin to lock or there is a fishtail
motion, turn the engine brake system OFF immediately and do not activate it
until road conditions improve.
4. Check your progressive braking switch often for proper position
(LOW/MED/HIGH), since road conditions can change quickly. Never skip a
step when operating the progressive braking system. Always go from OFF to
LOW and then to a higher position.
77
Engine Systems
Engine Systems
The engine systems are as follows:
Three-Filter Fuel System
The three-filter fuel system consists of DDEC control system, fuel injectors, low
and high pressure pumps, fuel filter module, prefilter, water separator/coalescer,
final filter, and the necessary connecting fuel lines. The common rail system with
injectors provides amplification for better fuel atomization.
Two-Filter Fuel System
The two-filter fuel system consists of DDEC control system, fuel injectors, low and
high pressure pumps, fuel filter module, prefilter, coalescer/final filter, and the
necessary connecting fuel lines. The common rail system with injectors provides
amplification for better fuel atomization.
Lubrication System
The lubrication system consists of an oil pump, oil cooler, cartridge-style oil filter,
pressure regulator valve, and oil pressure sensor. Clean, pressurized oil is fed to all
components via passages in the engine block and cylinder head.
Air System
Outside air enters the engine through the air filter and is drawn to the turbocharger
and then is compressed, and forced through the air-to-air charge cooler (heat
exchanger) and is cooled. Next, it flows to the intake manifold and into the
cylinders, where it mixes with atomized fuel from the injectors.
For optimum engine protection from dust and other airborne contaminants, service
the dry-type air cleaners used when the maximum allowable air restriction has been
reached.
Cooling System
A radiator/thermo-modulated fan cooling system is used on the engine. This system
has a centrifugal-type coolant pump to circulate coolant within the engine. One
full-blocking type thermostat located in the coolant module attached to the left side
of the cylinder block controls the flow of coolant. The coolant module incorporates
the oil cooler, oil filter, coolant filter (model year 2014 and prior engines only), and
coolant pump.
Electrical System
The electrical system consists of a starting motor, starting switch, battery-charging
alternator, storage batteries, and necessary wiring.
Exhaust System
Hot exhaust gas from the exhaust manifolds is used to drive the turbocharger.
78
Exhaust Gas Recirculation System

The Exhaust Gas Recirculation (EGR) system consists of an EGR cooler, EGR
valve and actuator. The EGR actuator opens and closes the EGR valve to allow hot
exhaust gas to enter the EGR cooler. Heat is extracted from the exhaust gas,
resulting in cooler exhaust gas to the cylinders. EGR lowers the temperature of the
exhaust from the engine, therefore, reducing exhaust gas emissions to acceptable
levels.
The purpose of the Exhaust Gas Recirculation System (EGR) is to reduce engine
exhaust gas emissions in accordance with EPA regulations.
The EGR system has been optimized to dramatically cut NOx formation by routing
a measured amount of exhaust flow to the cylinders to lower combustion
temperatures. Lower temperatures result in lower NOx levels without the negative
effects of retarding engine timing. The EGR valve has been moved to the top of the
engine for improved serviceability.
Engines for on-highway EPA 2007 regulation applications use a cooled EGR
system along with an Aftertreatment System to meet the emission standards.
On the 260 - 350 horsepower engines, the EGR is fed by all six cylinders. The low
horsepower engines use an asymmetric turbocharger with two entries, and the EGR
is fed from the first three cylinders, taken from a small entry. The exhaust with a
maximum exhaust gas temperature of 730C (1346F) is cooled to a maximum of
150C (302F) in the EGR cooler. The cooled exhaust gases then pass through the
EGR valve and added to the mixer housing. The addition of cooled exhaust gases
back into the combustion airflow reduces the peak cylinder combustion
temperature. Less oxides of nitrogen (NOx) are produced at lower combustion
temperatures.
79
EPA07 Aftertreatment Device
EPA07 Aftertreatment Device

In order to meet EPA07 emissions regulations, the traditional muffler was replaced
by a new Aftertreatment Device (ATD). The EPA07 ATD consists of a Diesel
Oxidation Catalyst (DOC) and a Diesel Particulate Filter (DPF). Together, these
two components burn off collected particulate matter in a process called
"regeneration." The key to successful regeneration is high exhaust temperature for
an extended period of time. Without adequate temperatures for regeneration, the
filter will continue to trap particulate and eventually plug. In order to avoid
plugging, Detroit has designed an actively-regenerated ATD.
1.
2.
3.
4.
5.
6.
7.
Doser Block Assembly

Intake Throttle Valve
Charge Air Cooler
EGR Valve
EGR Actuator
Fuel Doser Valve
DOC Inlet Temperature Sensor
8.
9.
10.
11.
12.
13.
14.
DOC Outlet Temperature Sensor

Sensor Junction Box
DPF Outlet Temperature Sensor
DPF Outlet Pressure Sensor
Diesel Particulate Filter
DPF Inlet Pressure Sensor
Diesel Oxidation Catalyst
Figure 28. EPA07 Aftertreatment Device
80
EPA10 Aftertreatment System

To meet EPA10 emission regulations, the traditional muffler was replaced by an
Aftertreatment Device (ATD). The ATD consists of a Diesel Oxidation Catalyst
(DOC), a Diesel Particulate Filter (DPF), and a Selective Catalyst Reduction (SCR)
system. These components burn off collected particulate matter in a process called
"regeneration" and reduce nitrous oxides (NOx). The key to successful regeneration
is high exhaust temperature for an extended period of time. Without adequate
temperatures for regeneration, the filter will continue to trap particulates and
eventually plug. In order to avoid DPF plugging, Detroit uses an actively
regenerated Aftertreatment System (ATS).
The exhaust from an on-highway diesel engine produces levels of nitrous oxide
(NOx) that must be reduced. To meet EPA10 emission standards, a Selective
Catalyst Reduction (SCR) system has been added to the current ATS. The SCR
system consists of an Aftertreatment Control Module (ACM), a tank for Diesel
Exhaust Fluid (DEF), a DEF pump module, an air control unit, a DEF metering
unit, a DEF injector, and an SCR module. DEF is pumped through the metering
unit to a DEF injector. The DEF injector meters DEF into the SCR module to
produce a chemical reaction. This chemical reaction converts nitrous oxides (NOx)
present in the exhaust stream into water vapor and nitrogen.
There are two different configurations available for different types of applications.
Both configurations reduce the particulate matter more commonly known as soot
and NOx generated by the engine.
1-BOX Aftertreatment Device
The "1-BOX" configuration contains the Diesel Oxidation Catalyst (DOC) /
Diesel Particulate Filter (DPF) and the Selective Catalytic Reduction (SCR
Catalyst) in one single enclosed box.
81
EPA10 Aftertreatment System
1. Diesel Oxidation Catalyst Outlet

Temperature Sensor
2. Diesel Oxidation Catalyst Inlet
Pressure Sensor Elbow
Temperature Sensor
4. Front Heat Shield
5. Diesel Exhaust Fluid Nozzle
6. Exhaust Outlet
7. Diesel Exhaust Fluid Metering Unit
8. Sensor Box including Pressure
Sensors
9. Exhaust Inlet
10. Selective Catalytic Reduction (SCR
Catalyst) Outlet Temperature
Sensor

Catalyst) Outlet NOx Sensor
Catalyst) Inlet NOx Sensor
13. 14-Pin Connectors
14. Diesel Particulate Filter Outlet
Pressure Sensor Elbow
Catalyst) Inlet Temperature Sensor
Catalyst) Inlet and Outlet NOx
Sensors (microprocessor mounted)
Pressure Sensor
Pressure Sensor
19. Diesel Particulate Filter
Temperature Sensor
Figure 29. 1-BOX Sensors

Two-Box Aftertreatment Device
The "Two-Box" configuration where the Diesel Oxidation Catalyst (DOC ) / Diesel
Particulate Filter (DPF) and the (SCR Catalyst) are located in separate components
and are mounted either vertically, horizontally, or both.
82
1. Diesel Exhaust Fluid Metering Unit

7. Diesel Particulate Filter Inlet
2. Diesel Exhaust Fluid Nozzle
Temperature Sensor
3. Selective Catalytic Reduction (SCR 8. Diesel Particulate Filter Outlet
Pressure Sensor
Sensor
Temperature Sensor
Catalyst) Inlet Temperature Sensor 10. Selective Catalytic Reduction (SCR
Temperature Sensor
Pressure Sensor
Figure 30. 2V2 Two-Box Sensors
83
GHG14 Aftertreatment System

The GHG14 Aftertreatment Device (ATD) has changed to an airless dosing system.
The airless dosing unit no longer relies on air pressure to atomize Diesel Exhaust
Fluid (DEF) in the Selective Catalyst Reduction (SCR). The SCR system consists
of an Aftertreatment Control Module (ACM2.1), a tank for DEF, a DEF pump, an
airless DEF dosing unit, and an SCR module. DEF is pumped to the airless dosing
unit through a high pressure DEF line at 10 bar (145 psi). The DEF dosing unit
injects a fine mist of atomized DEF into the SCR module to produce a chemical
reaction. This chemical reaction converts nitrous oxides (NOx) present in the
exhaust stream into water vapor and nitrogen.

Temperature Sensor
Pressure Sensor Tube
Temperature Sensor
5. Diesel Exhaust Fluid Dosing Unit
6. Exhaust Outlet
7. Exhaust Inlet
Sensor

Catalyst) Inlet and Outlet NOx
Sensors (microprocessor mounted)
Catalyst) Inlet NOx Sensors
15. 47-Pin Connector Harness
Pressure Sensor
Pressure Sensor
18. Sensor Bridge
Figure 31. GHG14 1-BOX Configuration

84

The GHG17 Aftertreatment System (ATS) is an airless dosing system. The
Selective Catalytic Reduction (SCR) system consists of an Aftertreatment Control
Module (ACM), a tank for Diesel Exhaust Fluid (DEF), a DEF pump, an airless
DEF dosing unit, and an SCR module. DEF is pumped to the airless dosing unit
through a high pressure DEF line at 10 bar (145 psi). The DEF dosing unit injects a
fine mist of atomized DEF into the SCR module to produce a chemical reaction.
This chemical reaction converts nitrogen oxides (NOx) present in the exhaust
stream into water vapor and nitrogen.
The SCR inlet temperature and Diesel Particulate Filter (DPF) outlet pressure
sensors have been eliminated for the GHG17 1-BOX ATS configured units. A
Soot Probe has been added to the 1-BOX ATS configurations. A Sensor Control
Unit (SCU) (2) has been added to the ATS and is directly wired to the Soot Probe
(1).
1. Soot Probe
2. Sensor Control Unit (SCU)
Figure 32. Soot Probe and Sensor Control Unit (SCU)

The GHG17 platform will continue with Hydrocarbon (HC) Dosing (regeneration
when the unit is driving over the road). A DEF-to-fuel ratio should be
approximately 4.3%. Due to a change in fueling strategy, the driver may notice a
change in engine noise during HC Dosing on the DD13 and DD15 platform.
85
1. Exhaust Outlet
Sensor
4. Soot Sensor
5. 18-Pin Connectors
6. Exhaust Inlet
Pressure Sensor
9. Diesel Exhaust Fluid Dosing Unit

Temperature Sensor
Temperature Sensor
14. DPF Outlet Temperature Sensor
15. ACM Cover
Figure 33. GHG17 1-BOX Configuration
86
Diesel Exhaust Fluid Information

NOTE: The following information pertains to EPA10/GHG14/GHG17 DD
Platform.
The Selective Catalytic Reduction (SCR) aftertreatment system for this engine
requires Diesel Exhaust Fluid (DEF) to maintain exhaust emissions at levels
compliant with emissions standards. DEF is a simple, non-toxic and inexpensive
pre-mixed fluid composed of 2/3 pure water and 1/3 automotive grade urea. The
following sections provide information regarding DEF availability, specifications,
handling and storage, and certain SCR ani-tampering features.
Diesel Exhaust Fluid Availability
DEF is available in bulk quantities at roadside truck stop service centers. DEF is
also available in various container sizes at Detroit service outlets, truck
dealerships, and many truck service centers. DEF is available in container sizes as
small as 2.5 gallons for convenient storage in your vehicle for emergency use. For
locations where DEF may be purchased, call the Detroit Customer Service
Center at l-800-445-1980.
Diesel Exhaust Fluid Specifications
DEF is manufactured to strict quality standards to ensure proper emissions control.
Only DEF that meets DIN70700 or ISO 22241-1 specifications can be used. The
American Petroleum Institute has developed a quality certification program to
ensure the quality of DEF available at service outlets.
Diesel Exhaust Fluid Handling and Storage
When stored at temperatures between 10 and 90 F (minus 12 and 32 C), DEF
has a minimum shelf life of 12 months. For best shelf life it is recommended that
Diesel Exhaust Fluid (DEF) containers be stored in a controlled environment.
Diesel Exhaust Fluid System Anti-Tampering Feature
The diagnostic system monitors for faults in DEF system components and monitors
the DEF supply pressure. If the diagnostics detect that components critical to the
Selective Catalytic Reduction (SCR Catalyst) or DEF supply system are
disconnected (which could indicate tampering), or if the diagnostics detect
abnormal system pressures indicative of DEF supply blockage, the warning lamp
will illuminate and the control system will initiate time and mileage counters. If the
sensors detect that the SCR system has been tampered with, the MIL illuminates to
warn the driver, and the engine performance is limited, with a 55 mph (90 km/h)
speed limit. If the system fault is not corrected, the STOP engine light illuminates
and a 5 mph (8 km/h) speed limit will be applied during non-driving conditions.
Similar warnings and penalties will result when insufficient urea quantity is
present.
87
Aftertreatment Device Operating Requirements
Aftertreatment Device Operating Requirements

NOTICE: Not following the operating requirements may result in damage to
the Aftertreatment Device (ATD) or accelerated ash plugging of the diesel
particulate filter.
NOTICE: Do not use kerosene or fuel blended with used lube oil.
Oxidation of particulate matter is the key to filter performance. This requires that
the catalyzing agent (platinum-coated passages) provide optimum enhancement to
the oxidation process. The following requirements must be met; otherwise the
Aftertreatment Device (ATD) warranty may be compromised:
Use Ultra-Low Sulfur Fuel (ULSF) with 15 ppm sulfur content or less, based on
ASTM D2622 test procedure.
Lube oil must have a sulfated ash level less than 1.0 wt %; currently referred to
as CJ-4 oil. Detroit currently recommends CJ-4 oil, and will allow CI-4 Plus
oil having sulfated ash levels of 1.4% or less.
88
EPA10 Diesel Exhaust Fluid (DEF) Purge Cycle

For EPA10 only, the DEF purge cycle is used to protect the DEF system from
freezing. The purge cycle starts right after the key is shut off. The vehicle's air
system is used to evacuate excess DEF from the DEF metering unit and nozzle
supply hose. During the purge cycle, air can be heard leaking, which should not be
mistaken as a leak. It is normal for the air pressure gauge to drop 9 to 12 psi during
this routine with the engine off.
NOTE: For trucks equipped with negative battery disconnect, do not turn
the battery disconnect switch off until the purge light (located on the battery
disconnect switch) turns off.
89
EPA10/GHG14/GHG17 Diesel Exhaust Fluid Tank
EPA10/GHG14/GHG17 Diesel Exhaust Fluid Tank

The Diesel Exhaust Fluid (DEF) tank holds the DEF supply. The filler neck has a
smaller diameter (19 mm) than the filler neck of the diesel fuel tank and is fitted
with a magnetic insert so that diesel fuel cannot be mistakenly added to the DEF
tank. The DEF you should use with your Detroit product will be API (American
Petroleum Institute) certified and meet the specifications ISO 22241-1 and
DIN70700. These are two widely accepted standards in use for qualifying DEF for
use in exhaust aftertreatment systems. DEF (Diesel Exhaust Fluid) will be sold at
over 2,500 locations throughout North America. These locations include:
Detroit Distributors
Freightliner Truck Dealers
Western Star Truck Dealers
Travel Centers of America Truck Stops
Petro Stopping Centers
Pilot Travel Centers
Additional Diesel Exhaust Fluid (DEF) sales locations can be found at
www.afdc.energy.gov/afdc/locator/def/
If diesel fuel is added to the DEF tank or DEF is added to the diesel fuel tank,
immediately contact your Certified Detroit Service Center for further
instructions.
90
Aftertreatment Maintenance
A high amount of black smoke emitting from the vehicle or illumination of the
Amber Warning Lamp or Red Stop Lamp are indications of a system problem.
Should this occur, consult your local Detroit Service Center.
Illumination of the Malfunction Indicator Lamp (MIL) Lamp indicates a failure of
an emissions control device. The MIL may illuminate along with other ATS
warning lamps. Call for service to repair the fault.
Illumination of the Diesel Particulate Filter (DPF) Regeneration Lamp indicates
that a parked regeneration is required.
There is a need to periodically remove accumulated ash, derived from engine lube
oil, from the filter. This ash does not oxidize in the filter during the regeneration
process and must be removed through a cleaning procedure. All Detroit ATD
equipped engines will illuminate a dashboard warning lamp indicating the need for
ash cleaning.
91
Performing a Parked Regeneration - EPA07
Performing a Parked Regeneration - EPA07

Perform a Parked Regeneration as follows:
NOTE: Under factory default settings, when the Diesel Particulate Filter
(DPF) Regeneration Lamp is not illuminated, the regeneration request
switch is disabled.
NOTE: The driver MUST stay with the vehicle throughout the regeneration
process.
NOTE: Not all vehicles may be equipped with a Regeneration Request
Switch due to application or user specification.
NOTE: The procedure will take approximately 30 to 40 minutes (depending
on engine type and the amount of soot accumulated in the DPF).
When the parked regeneration request is accepted, the Diesel Particulate Filter
(DPF) Regeneration lamp will turn ON one time for one second and then turn off
for the remainder of the parked regeneration. The High Exhaust System
Temperature (HEST) lamp will flash for one second every ten seconds and
eventually become solid when the tailpipe temperature is above 525C (977F).
The engine speed will increase to 1100 RPM for all DD Platform engines. The
regeneration will take 30-40 minutes. The regeneration is complete when the
engine returns to low idle and the DPF lamp remains OFF. The HEST lamp will
remain ON, but the vehicle may be driven.
NOTE: A parked regeneration will STOP and the engine will return to low
idle if any of the following happens:
The key is turned to the OFF position
The vehicle is put into gear
The clutch is cycled
The parking brake is released
92
1. HEST LAMP FLASHING: A Regeneration is in process and the system is

coming up to temperature.
2. Keep engine at slow idle (cannot be in Fast Idle or PTO Mode). Put
transmission in neutral (cycle out of neutral and then back into neutral) (if
equipped with an automatic transmission, cycle it into gear and then back to
neutral.).
NOTICE: Air tank pressure must be high enough for the parking brake
switch to hold in the OFF position.
3. Set park brake (cycle the park OFF to ON).
4. Press and release clutch pedal (if configured).
5. Hold DPF Switch to the ON position for five seconds and then release
(engine speed will increase and DPF lamp will go out).
93
Performing a Parked Regeneration - EPA10/GHG14
Performing a Parked Regeneration - EPA10/

GHG14
switch is disabled.
process.
The engine speed will increase to 1100 RPM for all DD Platform engines. The
regeneration will take 30 to 40 minutes. The regeneration is complete when the
engine returns to low idle and the DPF lamp remains OFF. The HEST lamp will
remain ON, but the vehicle may be driven.
94
NOTE: If a parked regeneration is being performed to check NOx

conversion, the calculated ambient temperature in the ACM (AS053) must
be above 0C (32F) or the test will fail.
NOTE: If the HEST LAMP is FLASHING, a regeneration is in process and
the system is coming up to temperature.
transmission in neutral (if equipped with an automatic transmission, cycle it
into gear and then back to neutral).
NOTICE: Air tank pressure must be high enough for the parking brake
switch to hold in the OFF position.
2. Set park brake (cycle the park brake OFF then ON for CPC R21 or lower
software).
3. Press and release clutch pedal once per ignition cycle (if configured).
95
Performing a Parked Regeneration - GHG17
Performing a Parked Regeneration - GHG17

switch is disabled.
process.
The engine speed may vary during parked regeneration (depending on engine
displacement, exhaust temperature and the amount of soot accumulated in the
DPF). The regeneration is complete when the engine returns to low idle and the
DPF lamp remains OFF. The HEST lamp will remain ON, but the vehicle may be
driven.
96
NOTE: If a parked regeneration is being performed to check NOx

conversion, the calculated ambient temperature in the ACM (AS053) must
be above 0C (32F) or the test will fail.
NOTE: If the HEST LAMP is FLASHING, regeneration is in process and the
system is coming up to temperature.
transmission in neutral (if equipped with an automatic transmission, cycle it
into gear and then back to neutral).
2. Set park brake (cycle the park brake OFF then ON).
3. Press and release clutch pedal once per ignition cycle (if configured).
97
Hazardous Applications
Hazardous Applications
The MCM should be configured to not allow automatically triggered over-the-road
regenerations (DPF Manual Regen Only Enable = Enabled).
NOTE: This applies for EPA07, EPA10, GHG14 and GHG17.
NOTE: This is for hazardous applications only.
During the time of purchase a customer should notify the dealer of the Hazardous
Application and the request for DPF Stationary Regen Only will be noted in the
purchase order. If the dealer was not notified during the time of purchase an
authorized Detroit maintenance or repair facility will need to contact Detroit
Technical Support for an application change.
There are two CPC options:
DPF Stationary Regen Only = 0-Disabled
DPF Stationary Regen Only = 1-Enabled
DPF Stationary Regen Only = 0-Disabled
This option allows the DPF Regen Switch to request a parked regeneration if the
parked regeneration entry conditions are met. This option also allows MCMinitiated over-the-road regenerations to occur.
DPF Stationary Regen Only = 1-Enabled
This option only allows a parked regeneration to occur by using the DPF
Regeneration Switch. The MCM will be unable to initiate an active over-the-road
regeneration when this option is enabled.
98
Service Record
It is mandatory that customers or distributors maintain a proper record of the
particulate filter servicing and cleaning. This record is an agent to warranty
considerations. The record must include information such as:
Date of cleaning or replacement
Vehicle mileage at the time of cleaning or replacement
Particulate filter part number and serial number(s)
99
Instrument Panel Lamps

The EPA10/GHG14/GHG17 instrument panel lamps are explained below:
Amber Warning Lamp
Table 3.
Lamp
Lamp Name
Amber Warning
Lamp (AWL)
Lamp Solid
Description
Results
Indicates a fault with

the engine controls.
Vehicle can be driven

to end of shift. Call
for service.
Lamp Flashing
At the start of every ignition cycle (bulb

check).
Diagnostic request switch is used to

activate the AWL to flash inactive codes.
When an electronic system fault occurs.

(Fault should be diagnosed as soon as
(EPA07 function only.)

Flashes last 90 seconds before idle
possible.)
shutdown if programmed for override.

Flashes when idle shutdown or the
optimized idle shutdown occurs.
Red Stop Lamp
100
Table 4.
Lamp
Lamp Name
Description
Results
Red Stop Lamp
Indicates a major
Move the vehicle to
(RSL)
engine fault that may

result in engine
damage. Engine
derate and/or
the nearest safe

location and shut
down the engine. Call
for service.
shutdown sequence
will be initiated.
Lamp Solid
check).
A potential engine damaging fault is
detected.
Lamp Flashing
Flashes when engine protection shutdown
occurs.
Diagnostic request switch is used to
activate the RSL to flash active codes.
(EPA07 function only).
Diesel Particulate Filter Regeneration Lamp

Table 5.
Lamp
Lamp Name
Description
Results
Diesel Particulate
Filter Regeneration
Solid yellow indicates Lamp Solid a regeneration is

regeneration is
Lamp
required. Blinking
yellow, derate and/or
required. Lamp
Flashing-
shutdown are
regeneration is
possible as soot load

continues to
required immediately.
increase. Lamp will

shut off during
parked regeneration.
Lamp Solid
Lamp Flashing

check).
When a regeneration is required immediately

(if the lamp flashing is ignored), a derate
Regeneration is required.
and/or shutdown could occur.
High Exhaust System Temperature Lamp
101
Table 6.
Lamp
Lamp Name
Description
Results
High Exhaust System Lamp is yellow.
Vehicle can be
Temperature (HEST)
Lamp
driven. Lamp solid for

an extended period
(Longer than 40
Minutes) - call for
Indicates exhaust
temperature is above
a preset limit and unit
is operating at low
vehicle speed (below service.

5 mph [8 kph]). When
the engine speed is
elevated for a parked
regeneration, lamp
will flash once every
10 seconds.
Lamp Solid
check).
Vehicle speed is less than 5 mph and the
Lamp Flashing
Flashes every 10 seconds when the
Selective Catalytic Reduction ( SCR
Catalyst) is not up to temperature
Diesel Particulate Filter (DPF) outlet

temperature is greater than 525 C (977
F).
Malfunction Indicator Lamp

Table 7.
Lamp
Lamp Name
Malfunction Indicator
Lamp (MIL)
Description
Results
Yellow lamp
Indicates a failure of
Vehicle can be driven

to end of the shift.
an Emission Control
device. May
Call for service.
illuminate at the
same time as the
Amber Warning
Lamp.
Lamp Solid
At the start of every ignition cycle (a bulb
check)
For any emission related fault (light out
when the fault is inactive)
Lamp Flashing
Never flashes
Fuel Filter Restriction Sensor Lamp: Fuel Filter Failed

102
Table 8.
Lamp
Lamp Name
Fuel Filter Restriction
Description
Yellow lamp
Results
Service soon
Sensor (FFRS) Lamp Indicates that the fuel

filter is restricted and
needs to be serviced.
May illuminate at the
same time as the
Lamp (MIL) and
Amber Warning
Lamp (AWL)
Lamp Solid
Lamp Flashing

check).
Fuel filter needs service.
Never
Water-In-Fuel Lamp (WIF)

Table 9.
Lamp
Lamp Name
Description
Water-In-Fuel (WIF)
Lamp
Yellow lamp indicates Engine water

that the fuel water
separator must be
separator has
reached its capacity
Results
drained or an engine
derate will occur.
and needs to be
drained.
Lamp Solid
Lamp Flashing

check).
Never
Water separator has reached it maximum

capacity.
103
EPA10/GHG14/GHG17 Diesel Exhaust Fluid Level Warning Lamps
EPA10/GHG14/GHG17 Diesel Exhaust Fluid Level

Warning Lamps
A four light bar segment indicates the Diesel Exhaust Fluid (DEF) level in 25%
increments. Low DEF levels will trigger a decrease in the engine's performance.
The use of improper DEF fluid will trigger a decrease in the engine's performance.
In an empty or an ignored state and the diesel fuel tank is filled without filling the
DEF tank, the vehicle's speed will be limited to 5 mph until DEF is detected in the
DEF tank.
Figure 34. Driver Card
104
Aftertreatment System Driver Notifications and

Actions
NOTE: Examples are shown as EPA07; all notifications and driver actions
will be the same on the DD platform. If it is determined a parked
regeneration is required, reference model year specific section: "Performing
a Parked Regeneration".
High Exhaust System Temperature Lamp
Table 10.
Notifications and
Description
Instrument Panel Lamp
High Exhaust System

Temperature (HEST)
lamp
Driver Action
No change in driving style

required.
SOLID: Exhaust is at high

When parked, keep
temperature and vehicle
vehicle at a safe distance
is at low speed or parked.
from people and
FLASHING: A parked
flammable materials or
regeneration is in process
vapors.
and the system is not up
to temperature.
Malfunction Indicator Lamp

Table 11.
Notifications and
Description
Lamp (MIL)
Indicates a failure of an
emission control device.
May illuminate at the
same time as the Check
Engine Lamp (CEL).
Driver Action
Vehicle can be driven to

end of shift. If the MIL
remains on after three drive
cycles, call for service.
105
Aftertreatment System Driver Notifications and Actions
Diesel Particulate Filter Regeneration Lamp

Table 12.
Notifications and
Description
(DPF) regeneration lamp
SOLID: Indicates that a
regeneration may be
needed.
FLASHING: Indicates
that a parked
regeneration is required
as soon as possible.
(DPF) is reaching system
Driver Action
Perform a parked
regeneration OR bring the
vehicle to highway speeds
to enable an automatic
regeneration of the filter.
Reference model year
specific section:
"Performing a Parked
Regeneration".
limits.
Diesel Particulate Filter Regeneration Lamp and the Check Engine

Lamp
106
Table 13.
Notifications and
Description
Driver Action
A parked regeneration
(DPF) regeneration lamp /
Check Engine Lamp
(CEL)
ENGINE DERATED
Indicates the Diesel
Particulate Filter (DPF)
has reached system
limits.
must be performed.
specific section:
Regeneration".
If the parked regeneration
exits and the lamps
remain on, repeat the
parked regeneration. If
the second attempt fails,
call for service.
Diesel Particulate Filter Regeneration Lamp, Check Engine Lamp, and

the Stop Engine Lamp
107
Aftertreatment System Driver Notifications and Actions
Table 14.
Notifications and
Description
Driver Action
A parked regeneration
must be performed.
specific section:

(DPF) regeneration lamp /
Check Engine Lamp
(CEL) / Stop Engine Lamp
(SEL)
ENGINE SHUTDOWN
Indicates the Diesel
Regeneration".
If the parked regeneration
exits and the lamps remain
on, repeat the parked
regeneration. If the second
attempt fails, call for
service.
Particulate Filter (DPF) has
Note: Engine can be
exceeded system limits.
restarted but a parked
regeneration must be
initiated within 30 seconds
or the engine will
shutdown.
108
DEF Post-Run Indicator Lamp

DEF Post-Run Indicator Lamp
An indicator system is required on vehicles equipped with a Negative Battery
Disconnect switch. The Post-Run Indicator lamp is controlled by the Aftertreatment
Control Module (ACM) and the Aftertreatment System (ATS). The Post-Run
Indicator lamp is located on the negative battery disconnect switch. If the ignition
is switched off while the ATS is at an elevated temperature, the ACM activates the
Post-Run cycle to cool the Diesel Exhaust Fluid (DEF) doser. The Post-Run cycle
will be interrupted if the Negative Battery Disconnect is switched off. The lamp
will illuminate if a Post-Run cycle is in progress, which informs the operator to
delay the Negative Battery Disconnect until the Post-Run Lamp is off, except in an
emergency situation.
109
Preventive Maintenance Intervals

The following guide establishes preventive maintenance intervals. These
recommendations should be followed as closely as possible to obtain long life and
optimum performance from your engine. When performed on a regular basis,
changing the engine oil, coolant, and filters is the least costly way of obtaining safe
and reliable vehicle operation. Added benefits and savings occur when you check
that the valves, fuel injectors, oil and cooling circuits are in good working order
during oil changes.
The intervals shown apply only to the maintenance functions described. These
functions should be coordinated with other regularly scheduled maintenance.
Scheduled Maintenance Intervals
Before placing your new vehicle in service, determine the correct maintenance
schedule application for your intended use of the vehicle.
Maintenance Schedule Applications
There are three types of maintenance schedules for the On-Highway Vehicle
applications; Severe Service, Short-Haul Service, and Long-Haul Service.
Severe Service:Severe service applies to vehicles that annually travel up to
48,000 kilometers (30,000 miles) and average less than 5 miles per gallon or that
operate under severe conditions.
Short Haul:Short Haul service applies to vehicles that annually travel up to
48,000 to 96,000 kilometers (30,000 to 60,000 miles) and average between 5.1
and 5.9 miles per gallon.
Long Haul:Long Haul service (over-the-road transport) applies to vehicles that
annually travel more than 96,000 kilometers (60,000 miles) and average greater
than 6 miles per gallon with minimal city stop-and-go operation.
Schedule Use
Complete each maintenance operation at the required interval. The intervals are
based on a collaboration of field and fleet data. For a more accurate analysis of
when fluids should be changed, such as engine oil, refer to publication Engine
Requirements; Lubricating Oil, Fuel and Filters and publication Coolant Selections
for Detroit Engines, available from authorized Detroit distributors and dealers.
Each maintenance table shows which maintenance operation must be performed at
the recommended interval (in miles, kilometers, and hours).
NOTE: Failure to maintain the cooling system at required
concentrations will result in severe damage to the engine cooling
system and related components. Refer to the "Coolant Selections and
Maintenance" section.
110
Cooling System Flush and Fill

Coolant Flush and Fill - Proper maintenance of the cooling system is vital to its
performance and longevity. The cooling system must, on a constant basis, deal with
cavitation, temperature / pressure swings, and continuous threats on the additive
package. Once the additives have been depleted from the coolant, it will only be a
matter of time until the engine components suffer. Refer to section "Cooling
System Fill Procedure"
Cooling System Inspection - Inspect the cooling system as follows:
1. Inspect the radiator, condenser, coolant pump, engine oil cooler, freeze plugs,
and heat exchanger for damage and leaks.
2. Check all cooling system pipes and hoses for damage and leaks; ensure they
are positioned to avoid chafing, and are securely fastened.
3. Check the outside of the radiator and condenser for blockage. Check fins for
damage; straighten them if necessary.
Valve Lash Checking and Adjustment
Valve lash checking and adjustment should be performed per the maintenance
intervals prescribed under the proper service category for the engine. All three
service categories (Severe, Short Haul, and Long Haul) require a 'first time' valve
lash adjustment at a shorter interval. After the initial adjustment, all others are
based on the same mileage intervals. Proper valve lash clearance allows the engine
to produce the best possible performance with the lowest emissions. Valve lash
adjustments should be performed by an authorized Detroit maintenance or repair
facility.
Drive Belt
DD Platform engines utilize a specially designed Ethylene Propylene Diene
Monomer (EPDM) belt material which is exclusive to the Original Equipment
Manufacturer (OEM) component. Replacement with an aftermarket part may lead
to shortened maintenance intervals and excessive noise.
Drive belts wear differently based on environmental conditions and vehicle duty
cycle. If the vehicle is operated in extremely hot or cold climates, or is exposed to
significant dust/debris/road salt, lifetime of the belts may be significantly reduced.
111
Fuel / Water Separator

Incorporated into the fuel filter module is a fuel/water separator. The separator
removes emulsified water as well as droplets and is located in the lower
compartment of the fuel filter module. A water-in-fuel (WIF) sensor indicates when
trapped water needs to be drained.
NOTICE: Do not over-tighten the water drain valve. Failure to properly
tighten the water drain valve may cause damage to the water drain valve
and housing.
1. Water in Fuel Separator Cap

2. Water Drain Valve
3. Final Filter Cap

4. Pre Filter Cap
Figure 35. Three-Filter Fuel System Fuel Filter Module
112
1. Water in Fuel Separator(Coalescer/

Final Filter) Cap
2. Pre Filter Cap
3. Water Drain Valve
Figure 36. Two-Filter Fuel System Fuel Filter Module

Three-Filter Fuel Filters
The prefilter is housed within the fuel filter module. The prefilter element filters
particles down to 100 microns and is snapped into the prefilter cap. The water
separator/coalescer filter is housed within the fuel filter module. The water
separator/coalescer has the task of separating out the water contained in the fuel
and also filtering out particles down to 10 microns. The water separator/coalescer
filter snappes into the water separator/coalescer cap. The final filter is housed
within the fuel filter module. The final filter element filters particles down 3 to 5
microns and snaps into the final filter cap.
Two-Filter Fuel Filters
The prefilter is housed within the fuel filter module. The prefilter element filters
particles down to 100 microns and is snapped into the prefilter cap. The coalescer/
final filter is housed within the fuel filter module. The coalescer/final filter has the
task of separating out the water contained in the fuel and also filtering out particles
down to 3 to 5 microns. The coalescer/final filter snaps into the coalescer/final filter
cap.
Air System
Air Cleaner - The air cleaner element should be inspected per the maintenance
intervals or more often if the engine is operated under severe dust conditions.
113
Replace the element, if necessary. Check the gaskets for deterioration and replace,
if necessary. If the dry-type air cleaner is equipped with an aspirator, check for
aspirator damage or clogging. Clean, repair or replace, as necessary.
NOTICE: Do not allow the air inlet restriction to exceed 5.5 kPa (22 in.
H2O) under any engine operating conditions. A clogged air cleaner element
will cause excessive intake restriction and reduced air supply to the engine
resulting in increased fuel consumption, inefficient engine operation and
reduced engine life.
Inspect the entire air system for leaks daily. Look especially for torn air inlet piping
or boots and loose or damaged clamps. Have worn or damaged parts repaired or
replaced, as required. Retighten loose connections
Air Cleaner Replacement - Dry type air cleaner elements should be replaced after
one year of service or when the maximum allowable air intake restriction has been
reached, whichever comes first.
Air-to-Air Charge Cooler - Periodically inspect the air-to-air charge cooler for
buildup of dirt, mud, etc. and wash off using a mild soap solution. Check the charge
cooler, ductwork, and flexible connections for leaks and have repaired or replaced,
as required.
Exhaust System
The exhaust manifold retaining bolts and other connections should be inspected for
leaks. The exhaust pipe rain cap should be checked for proper operation, if so
equipped. With the introduction of an Aftertreatment system, the sealing of the
exhaust system is critical and should be inspected regularly.
Air Compressor
The air compressor incorporates three of the major systems of a diesel engine (air,
lubrication, and coolant). Proper inspection of air compressor would include
inspecting for air, oil, and coolant leaks. Due to inadequate internal sealing air
compressors, when failed, can produce excessive crankcase pressure or allow an
engine to ingest oil.
Aftertreatment System (ATS)
There is a need to periodically remove accumulated ash, derived from engine lube
oil, from the filter. This ash does not oxidize in the filter during the regeneration
process and must be removed through a cleaning procedure. All Detroit ATSequipped engines will illuminate a dashboard warning lamp indicating the need for
ash cleaning.
Vibration Damper
The viscous vibration damper should be inspected periodically and replaced if
dented or leaking. Heat from normal engine operation may, over a period of time,
cause the fluid within the damper to break down and lose its dampening properties.
For this reason the viscous vibration damper must be replaced at time of normal
major engine overhaul, regardless of apparent condition.
114
EPA07 DD Series Preventive Maintenance Tables

Table 15.
Severe Service Maintenance Intervals (EPA07)
Miles X 1000/
25
Km X 1000/
40
Hours*
640
50
75
100
125
150
175
200
80
120
160
200
240
280
320
1280 1925 2565 3205 3850 4490 5130
Lubricating Oil
Lubricating Oil Filter
Coolant
Refer to section How to Select Coolant for the listing

of required intervals using the recommended coolants.
Cooling System Filter
R
Fuel Filters without Frame-mounted Filter
Fuel Filters
Change filters every 25,000 miles.

Fuel Filters with Frame-mounted Filter
Frame-mounted Filter
Change frame filter every 25,000 miles.
Fuel Filters
Initial Valve Lash Adjustment

Adjust at 60,000 mi (100,000 km), at 180,000 mi
(300,000 km), and then at every 180,000 mi. (300,000
km) or nearest maintenance interval.
Belts
Air System
Air Cleaner
Exhaust System
Aftertreatment Device
Air Compressor
Inspect external hardware and connections at every

oil change. Remove ash at 300,000 miles (480,000
km) or 9,000 hours.*
I
*Whichever comes first.

All items are described in "Routine Preventive Maintenance."
Currently, only Detroit Fuel Filter/Water Separator & Davco 482/485/487 are the only
frame-mounted filtration systems compatible for Detroit Engines.
R = Replace
I = Inspect
115
EPA07 DD Series Preventive Maintenance Tables
Table 16.
Short Haul Service Maintenance Intervals (EPA07)
Miles X 1000/
35
70
105
140
175
210
245
280
Km X 1000/
55
110
165
220
275
330
385
440
Hours
895
1795 2690 3590 4485 5380 6280 7180
Lubricating Oil
Coolant

R
Fuel Filters

Fuel Filters
Adjust at 60,000 mi (100,000 km), at 180,000 mi

Belts
Air System
Air Cleaner
Exhaust System
Air Compressor

I

R = Replace
I = Inspect
Table 17.
Long Haul Service Maintenance Intervals (EPA07)
Miles X 1000/
50
100
150
200
250
300
Km X 1000/
80
160
240
320
400
480
Hours
1280
2565
3845
5125
6410
7690
Lubricating Oil
116
Long Haul Service Maintenance Intervals (EPA07)

Coolant

R
Fuel Filters

Fuel Filters

Adjust at 60,000 mi (100,000 km), at 180,000 mi.
Belts
Air System
Air Cleaner
Exhaust System
Air Compressor

I

R = Replace
I = Inspect
117
EPA10/GHG14/GHG17 DD Series Preventive Maintenance Tables
EPA10/GHG14/GHG17 DD Series Preventive

Maintenance Tables
NOTE: Actual fuel filter life will vary based on fuel quality.
NOTE: Diesel Oxidation Catalyst (DOC) and the Selective Catalytic
Reduction (SCR Catalyst) do not require maintenance.
Table 18.
Severe Service Maintenance Intervals (EPA10/GHG14/GHG17)
Miles X 1000/
25/
50/
75/
100/
125/
150/
Km X 1000/
40/
80/
120/
160/
200/
240/
Hours*
640
1280
1925
2565
3205
3850
Lubricating Oil
Coolant
Refer to section "How to Select Coolant" for the

listing of required intervals using the
recommended coolants.
Cooling System Filter (if equipped)

Fuel Filters

Fuel Filters
Valve Lash Adjustment
Adjust at 100,000 miles (160,000 km), at 500,000

miles (800,000 km), and then every 500,000 miles
(800,000 km) thereafter.
Belts
Air System
Air Cleaner
Exhaust System
Aftertreatment Devices
Inspect external hardware and connections every

6 months or at oil change intervals.
Diesel Particulate Filter (EPA10,

GHG14)
A Check Engine Light will illuminate when ash

requires removal. Normal DPF ash clean intervals
are 300,000 miles (480,000 km) 9,000 hours to
400,000 miles (640,000 km) 10,250 hours.**
118
Severe Service Maintenance Intervals (EPA10/GHG14/GHG17)

Diesel Particulate Filter (GHG17)

requires removal. Normal DPF ash clean interval
is 390,000 miles (627,000 km) 10,000 hours. **
DEF Pump Filter
EPA10 and GHG14 - Replace filter every 175,000

miles (280,000 km).
GHG17 Only - Replace filter every 3 years or
500,000 miles, whichever comes first.
DEF Pump Air Bladder
(2010 engines only) Refill bladder with air every

24 months.
Air Compressor

**Detroit highly recommends replacing the DPF with a Detroit genuine DPF to ensure
maximum replacement life.
Refer to "Routine Preventive Maintenance" for a description of all items.
R = Replace
I = Inspect
Table 19.
Short Haul Maintenance Intervals (EPA10/GHG14/GHG17)
Miles X 1000/
35/
70/
105/
140/
175/
Km X 1000/
55/
110/
165/
220/
275/
Hours*
895
1795
2690
3590
4485
Lubricating Oil
Coolant
Refer to section "How to Select Coolant" for the

listing of required intervals using the

Fuel Filters

Fuel Filters

Belts
Air System
Air Cleaner
119
EPA10/GHG14/GHG17 DD Series Preventive Maintenance Tables
Short Haul Maintenance Intervals (EPA10/GHG14/GHG17)

Exhaust System


GHG14)

400,000 miles (640,000 km) 10,250 hours.**

is 400,000 miles (640,000 km) 10,250 hours to
500,000 miles (800,000 km) 11,000 hours. **
DEF Pump Filter

miles (280,000 km).

24 months.
Air Compressor

R = Replace
I = Inspect
Table 20.
Long Haul Maintenance Intervals (EPA10/GHG14/GHG17)
Miles X 1000/
50/
100/
150/
200/
250/
300/
Km X 1000/
80/
160/
240/
320/
400/
480/
1280
2565
3845
5125
6410
7690
Hours*
Lubricating Oil
Coolant
Refer to section "How to Select Coolant" section

for the listing of required intervals using the

Fuel Filters

120
Long Haul Maintenance Intervals (EPA10/GHG14/GHG17)

Fuel Filters

Belts
Air System
Air Cleaner
Exhaust System


GHG14)

400,000 miles (640,000 km) 10,250 hours.**

is 500,000 miles (800,000 km) 11,000 hours to
550,000 miles (880,000 km) 11,500 hours. **
DEF Pump Filter

miles (280,000 km).

Air Compressor

24 months.
I

R = Replace
I = Inspect
121
EPA10/GHG14/GHG17 DD Series Preventive Maintenance Tables for Recreational Vehicles
EPA10/GHG14/GHG17 DD Series Preventive

Maintenance Tables for Recreational Vehicles
NOTE: Diesel Oxidation Catalyst (DOC) and the SCR (Selective Catalytic
Reduction) Catalyst do not require maintenance.
Table 21.
Maintenance Intervals for Recreational Vehicles (EPA10/GHG14/GHG17)
Miles X 1000/
35/
70/
105/
140/
175/
Km X 1000/
55/
110/
165/
220/
275/
Hours*
895
1795
2690
3590
4485
Lubricating
Oil
Lubricating
Oil Filter
Coolant
Cooling
System Filter
(if equipped)
Refer to section "How to Select Coolant" for the listing of required intervals
using the recommended coolants
-

Fuel Filters

Framemounted
Filter
Fuel Filters
Valve Lash
Adjustment
Adjust at 100,000 miles (160,000 km), at 500,000 miles (800,000 km), and
then every 500,000 miles (800,000 km) thereafter.
Belts
Air System
Air Cleaner
Exhaust
System
Aftertreatmen
t Devices
122
Inspect external hardware and connections every 6 months or at oil change

intervals.
Maintenance Intervals for Recreational Vehicles (EPA10/GHG14/GHG17)

Diesel
Particulate
Filter
(EPA10,
GHG14)
A Check Engine Light will illuminate when ash requires removal. Normal DPF
ash clean intervals are 300,000 miles (480,000 km) 9,000 hours to 400,000
miles (640,000 km) 10,250 hours.**
Diesel
Particulate
Filter
(GHG17)
A Check Engine Light will illuminate when ash requires removal. Normal DPF
ash clean interval is 400,000 miles (640,000 km) 10,250 hours to 500,000
miles (800,000 km) 11,000 hours. **
DEF Pump
Filter
EPA10 and GHG14 - Replace filter every 175,000 miles (280,000 km).
GHG17 Only - Replace filter every 3 years or 500,000 miles, whichever
comes first.
DEF Pump
Air Bladder
(2010 engines only) Refill bladder with air every 24 months.
Air
Compressor
R = Replace
I = Inspect
123
Routine Preventive Maintenance

This section describes the items listed in the maintenance interval tables. The Daily
instructions apply to routine or daily starting of the engine. They do not apply to a
new engine or one that has been operated for a considerable period of time.
Monitoring the Lubricating Oil

Perform the following maintenance on the lubricating oil:
1. Check the oil level daily with the engine stopped and on a level surface. If
the engine has just been stopped and is warm, wait approximately 20 minutes
to allow the oil to drain back into the oil pan before checking.
NOTE: the dipstick has a positive locking device such as a lever or twistlock design that must be disengaged before pulling the dipstick out of the
guide tube. Use a shop rag to wipe off the end of the dipstick. Wait 15
seconds to allow any crankcase pressure to dissipate through the guide
tube and let the oil level settle in the oil pan.
2. Add the proper grade of oil to maintain the correct level on the dipstick.
Remove the dipstick from the guide tube. Before adding lubricating oil,
refer to "How to Select Lubricating Oil."
NOTICE: Do NOT fill beyond the maximum fill level on the dipstick, since
overfilling may result in high oil consumption and possible severe engine
damage.
NOTE: If the engine operating temperature is below 60 C (140 F), the
operating temperature of 60 C (140 F), parked on a level surface and then
3. Reinstall the dipstick and make sure it is fully inserted into the guide tube.
Remove the dipstick and read the oil level dipstick.
NOTICE: Do not add oil if the oil reading is in the crosshatch area on the
dipstick. There are approximately 5.0 L (5.2 qts) from the minimum mark to
the maximum mark on the dipstick. Overfilling the oil pan can cause engine
damage.
NOTICE: If the oil level is constantly above normal and excess oil has not
been added to the crankcase, consult with an authorized Detroit service
outlet for the cause. Fuel or coolant dilution of lubricating oil can result in
serious engine damage.
124
4. Check the oil level daily. With the engine stopped, use the oil dipstick and
measure the oil level on crosshatch area on the dipstick. Figure below shows
Maximum oil level (1) and Minimum oil level (2). If the oil reading is in the
crosshatch area or between the bends of the dipstick, then the oil is at the
proper level for engine operation.
5. Add the proper grade of oil to maintain the satisfactory range on the
dipstick. All diesel engines are designed to use some oil, so the periodic
addition of oil is normal. Before adding lubricating oil, refer to "How to
Select Lubricating Oil."
Monitoring the Lubricating Oil Filter

The engines are equipped with a single cartridge-style oil filter (1) that is part of the
oil/coolant module. Incorporated into the housing is a drain back port which allows
residual oil to be returned to the oil pan when the filter is removed. This design,
including the cartridge style element, allows for a more environmentally-safe oil
change.
NOTE: Model year 2014 and prior engines have a coolant filter.
125
Perform the following maintenance on the Lubricating Oil Filter:

1. Replace the oil filters when recommended by the appropriate maintenance
table.
Refer to section "EPA07 DD Series Preventive Maintenance Tables"
Refer to section "EPA10/GHG14 DD Series Preventive Maintenance Tables"
2. Make a visual check of all lubricating oil lines for wear and/or chafing. If any
indication of wear is evident, replace the oil lines and correct the cause.
3. Check for oil leaks after starting the engine.
Monitoring the Cooling System

The cooling system must be full for proper operation of the engine.
1. Check the coolant level daily and maintain it between the full and low marks
on the surge tank.
2. Add coolant as required, but do not overfill. Before adding coolant, refer to
"How to Select Coolant" for the listing of required intervals using the
recommended coolants
126
Checking for Coolant Leaks

Perform daily visual checks for cooling system leaks. Look for an accumulation of
coolant when the engine is running and when it is stopped.
NOTE: Coolant leaks may be more apparent on a engine when it is cold.
wheels are blocked.
Coolant Inhibitors
The inhibitors in antifreeze solutions must be replenished with an approved
corrosion inhibitor supplement when indicated by testing the coolant. Refer to
section "How to Select Coolant" for the listing of required intervals using the
recommended coolants for required test intervals, inhibitor levels, and approved
inhibitors.
NOTICE: Coolant must be inhibited with the recommended Supplemental
Coolant Additives listed in this manual. Failure to check and maintain
Supplemental Coolant Additive levels at required concentrations will result
in severe damage (corrosion) to the engine cooling system and related
components.
The cooling system is protected by a Supplemental Coolant Additive element. In
addition, the engine can be equipped with a coolant filter/inhibitor system as an
installed option or as an after-sale item.
Coolant Drain Interval
A coolant system properly maintained and protected with supplemental coolant
inhibitors can be operated up to the intervals listed. At these intervals the coolant
must be drained and disposed of in an environmentally responsible manner
according to state and/or federal Environmental Protection Agency (EPA)
recommendations.
Inspection of the Radiator

Inspect the radiator as follows:
1. Inspect the exterior of the radiator core every 30,000 miles (50,000 km) or 12
months.
127
WARNING: EYE INJURY

NOTE: It may be necessary to clean the exterior of the radiator more
frequently if the engine is being operated in extremely dusty or dirty areas.
2. If necessary, clean the exterior using a quality grease solvent, such as
mineral spirits, and dry with compressed air. Do not use fuel oil, kerosene,
or gasoline.
3. If the low coolant level sensor is installed in the top tank of the radiator, test
for proper operation every 100,000 miles (160,000 km) or 12 months,
whichever comes first. Authorized Detroit distributors are properly
equipped to perform this service.
Monitoring the Cooling System Filter

NOTE: DD Platform engines built 2015 and later may not be equipped with
a coolant filter.
Install a new cooling system filter at the distance intervals indicated by each
specific Maintenance Interval chart.
Monitoring the Fuel Filters

Monitoring the Three-Filter Fuel System Filters
The engine is equipped with a prefilter that filters down to 100 microns, a water
separator/coalescer that separates water and also filtering out particles down to 10
microns, and a final filter which filters material from 3 to 5 microns. The final filter
is 98% effective at filtering material at 5 microns. When servicing these elements,
all three filters should be changed at the same time. All three elements are located
within the fuel filter module located on the left side of the engine.
1. Located at the base of the fuel filter module is a water level sensor. Check
the water level sensor each day.
and housing.
128
2. When water level reaches a predetermined height, the LED indicators on the
front of the sensor change from green to red. At this time, remove the water
from the module by opening the water drain valve at the bottom of the
module.
NOTE: Filter change intervals may be shortened to conform with
established preventive maintenance schedules, but should never be
extended.
3. Replace the fuel filters using the Preventative Maintenance Tables.
Monitoring the Two-Filter Fuel System Filters

The engine is equipped with a prefilter that filters down to 100 microns, a
coalescer/final filter that separates water, and filters down to 3 to 5 microns. When
servicing these elements, all two filters should be changed at the same time. All
two elements are located within the fuel filter module located on the left side of the
engine.
and housing.
NOTE: Filter change intervals may be shortened to conform with
established preventive maintenance schedules, but should never be
extended.
1. Replace the fuel filters using the Preventative Maintenance Tables.
Adjusting the Valve Lash

NOTE: Proper valve lash clearance allows the engine to produce the best
possible performance with the lowest emissions. Valve lash adjustments
should be performed by an authorized Detroit maintenance or repair
facility.
Perform a valve lash adjustment as scheduled for the appropriate engine duty cycle.
Monitoring the Belt Tensioner

DD Platform engines are equipped with an automatic tensioning device. No
adjustment or periodic maintenance is required.
129
Poly-V-Belt Inspection
Periodically inspect the belts based on the damage guide below. If any damage is
noted, replace both belts (Fan and Accessory Belts). A precision wear gauge,
available from Gates, is the preferred method of determining belt wear.
Table 22.
Poly-V-Belt Inspection Concerns
130
ABRASION
CHUNK-OUT
IMPROPER INSTALL
CRACKING
Table 23.
Poly-V-Belt Inspection Concerns
PILLING
UNEVEN RIB WEAR
MISALIGNMENT
GRAVEL PENETRATION
Monitoring the Serpentine Belts

Two poly-V-belts (8 and 9) are used on the engine for On-Highway Vehicle
applications. One belt drives the fan hub and the other belt drives the remaining
accessories. To provide proper running tension, the system utilizes an automatic
tensioning device. Automatic belt tensioners require no adjustment.
131
Replacement of Belts
DD Platform engines utilize a specially designed EPDM belt material which is
exclusive to the OE component. Replacement with an aftermarket part may lead to
shortened maintenance intervals and excessive noise.
If the vehicle is operated in severely cold/hot temperatures, or is exposed to
significant dust/debris/road salt, the belts may require replacement prior to mileage
specified in the maintenance interval section.
Inspection of the Air Intake System

Perform the following maintenance on the Air Intake System:
1. Inspect all the connections in the air system to make sure they are tight and
leak-free.
2. Check all hoses and ducting for punctures, deterioration, or other damage and
replace, if necessary.
Monitoring the Air Cleaner

The engine is equipped with an engine-mounted air cleaner that is flat in design to
accommodate various vehicle packages. Replace dry type air cleaner elements
when the maximum allowable air intake restriction has been reached.
1. Inspect the air cleaner element every 50,000 miles (80,000 km) or more often
if the engine is operating under severe dust conditions. Replace the element,
if necessary.
2. Check the gaskets for deterioration and replace, if necessary.
3. If the dry type air cleaner is equipped with an aspirator, check for aspirator
damage or clogging. Clean, repair or replace, as necessary.
132
NOTICE: Do not allow the air inlet restriction to exceed 20 in. H2O (5.0
kPa) under any engine operating conditions. A clogged air cleaner element
will cause excessive intake restriction and reduced air supply to the engine
resulting in increased fuel consumption, inefficient engine operation, and
reduced engine life.
4. Inspect the entire air system for leaks daily.
a. Look especially for torn air inlet piping or boots and loose or
damaged clamps. Have worn or damaged parts repaired or replaced,
as required.
b. Re-tighten loose connections.
Monitoring the Exhaust System

Inspect the Exhaust System as follows:
1. Check the exhaust manifold retaining bolts and other connections for
tightness.
2. Check the exhaust pipe rain cap for proper operation, if so equipped.
Monitoring the Aftertreatment System

NOTE: All Detroit Aftertreatment System (ATS) - equipped engines will
illuminate a dashboard warning lamp indicating the need for ash cleaning.
Periodically the accumulated ash derived from the engine's lubricating oil needs to
be removed from the ATS. This ash does not oxidize in the filter during the
regeneration process and must be removed through a cleaning procedure.
Inspection of the Air Compressor

The air compressor incorporates three of the major systems of a diesel engine (air,
lubrication, and cooling). Inspect the air compressor looking for air, oil, and
coolant leaks.
Monitoring the Fuel and Fuel Tank

To prevent fuel and fuel tank problems, the following measures are recommended:
1. Keep the fuel tank filled to reduce condensation.
2. Before adding fuel, Refer to section "How to Select Diesel Fuel"
3. Refill the tank at the end of each day's operation to prevent condensation
from contaminating the fuel. Condensation formed in a partially filled tank
promotes the growth of microorganisms that can clog fuel filters and restrict
fuel flow.
133
4. To prevent microbe growth, add a biocide to the fuel tank or primary fuel
supply only as needed.
5. Open the drain at the bottom of the fuel tank every 30,000 miles (50,000
kilometers) to drain off any water and/or sediment.
To avoid injury from improper use of chemicals, follow the
chemical manufacturer's usage, handling, and disposal
instructions. Observe all manufacturer's cautions.
NOTICE: Never use galvanized steel fuel tanks, fittings, pipes, or supply
lines. The fuel reacts chemically with the zinc coating to form powdery
flakes that can quickly clog the fuel filters and damage the fuel pumps and
injectors.
6. Every 120,000 miles (200,000 kilometers) or 12 months, tighten all fuel
tank mountings and brackets. At the same time, check the seal in the fuel
tank cap, the breather hole in the cap, and the condition of the flexible fuel
lines. Repair or replace the parts, as necessary.
Inspection of Hoses and Fittings for Fuel Leaks

A pre-start inspection of hoses and fuel lines is recommended. Make a visual check
for fuel leaks at all engine-mounted fuel lines and connections, and at the fuel tank
suction and return lines. Since fuel tanks are susceptible to road hazards, leaks in
this area may best be detected by checking for an accumulation of fuel under the
tank.
WARNING: HOT OIL
NOTE: Leaks are not only detrimental to machine operation, but they can
also result in added expense caused by the need to replace lost fluids
Inspection of Hoses and Fittings
Check hoses daily as part of the pre-start inspection.
Examine hoses for leaks, and check all fittings, clamps and ties carefully.
Make sure hoses are not resting on or touching shafts, couplings, heated surfaces
including exhaust manifolds, sharp edges, or other obvious hazardous areas.
Since all machinery vibrates and moves to a certain extent, clamps and ties can
fatigue with age. To ensure continued proper support, inspect fasteners
frequently and tighten or replace them as necessary.
134
If fittings have loosened or cracked, or if hoses have ruptured or worn through,

take corrective action immediately.
Inspection of Hoses with Extended Service Life
A hose has a finite service life. With this in mind, inspect hoses as follows:
NOTE: Fire-resistant fuel and lubricating oil hose assemblies do not require
automatic replacement after five years of service or at major overhaul, but
should be inspected carefully before being put back into service.
1. Thoroughly inspect all hoses at least every 500 operating hours (1,000 hours
for fire-resistant fuel and lubricating oil hoses) and/or annually. Look for
cover damage and/or indications of twisted, worn, crimped, brittle, cracked or
leaking lines. Hoses with their outer cover worn through or with damaged
metal reinforcements should be considered unfit for further service.
2. Replace all hoses in and out of machinery during major overhaul and/or after
a maximum of five (5) years of service.
Inspection of the Turbocharger and Charge Air Cooler

Inspect turbocharger and charge air cooler as follows:
1. Visually inspect the turbocharger mountings, intake and exhaust ducting, and
connections for leaks daily.
2. Check the lubricating oil inlet and outlet lines for leaks or restrictions to oil
flow.
3. Check the turbocharger for unusual noise or vibration and, if excessive, stop
the engine and do not operate until the cause is determined.
4. Periodically inspect the air-to-air charge air cooler for buildup of dirt, mud,
or other debris. Clean as necessary.
5. Check the charge air cooler, duct work, and flexible connections for leaks
and repair or replace as required.
Inspection of the Battery

Inspect the battery as follows:
To avoid injury from accidental engine startup while servicing the
engine, disconnect/disable the starting system.
135
1. Check for cracks in the battery cases (1), for tightness of the cable clamps
(2) at the terminals, and for corrosion of the terminals (3). Service or replace
as needed.
2. Keep the terminal surface clean.

3. Inspect the cables, clamps and hold-down brackets regularly. Clean and
reapply a light coating of petroleum jelly when needed. Have corroded or
damaged parts replaced.
4. If the engine is to be out of service for more than 30 days, remove the
batteries and store in a cool, dry place.
a. Keep batteries fully charged, if possible.
b. Replace any battery that fails to hold a charge.
5. Periodically check battery connections for corrosion and tightness.
a. If necessary, remove connections and wire brush any corrosion from
terminals and cable ends.
b. Replace damaged wiring.
Steam Cleaning the Engine

NOTICE: Do not apply steam or solvent directly to the battery-charging
alternator, starting motor, DDEC components, sensors or other electrical
components, as damage may result.
The engine and engine compartment should be steam cleaned every 60,000 miles
(100,000 km) or 2,000 hours, whichever comes first.
136
Inspection of the Battery-Charging Alternator

Precautions must be taken when working on or around the alternator. The diodes
and transistors in the alternator circuit are very sensitive and can be easily
destroyed. To avoid equipment damage, the following conditions must be met:
battery acid:

Avoid grounding the output terminal. Grounding an alternator output wire or

terminal (which is always hot, regardless of whether or not the engine is running)
and accidentally reversing the battery polarity will result in equipment damage.
Do not reverse battery connections.
Never disconnect the battery while the alternator is operating. Disconnecting the
battery can result in damage to the battery diodes. In applications which have
two sets of batteries, switching from one set to the other while the engine is
running will momentarily disconnect the batteries.
If a booster battery is to be used, batteries must be connected correctly (negative
to negative, positive to positive).
Never use a fast charger with the batteries connected or as a booster for battery
output.
For information on the alternator assembly, contact an authorized distributor,
depending on manufacturer.
Check the alternator as follows:
1. Inspect the terminals for corrosion and loose connections and wiring for
damage and frayed insulation. Have wiring repaired or replaced, as required.
2. Check torque on alternator mounting bolts and bracketing every 30,000 miles
(50,000 km). Re-tighten if necessary.
Lubricating the Fan Hub

If the fan bearing hub assembly has a grease fitting, use a hand grease gun to
lubricate the bearings with one shot of quality lithium-based, multipurpose grease
every 120,000 miles (200,000 km). Care should be taken not to overfill the bearing
housing.
137
Checking the Vibration Damper

Check the vibration damper as follows:
1. Inspect the viscous vibration damper (1) periodically and replace if dented or
leaking.
2. Heat from normal engine operation may, over a period of time, cause the
fluid within the damper to break down and lose its dampening properties. For
this reason, replace the viscous vibration damper at time of normal major
engine overhaul, regardless of apparent condition.
138
How to Procedures
This section covers the Detroit recommendations on how to select lubricating oil,
diesel fuel, and coolant. Also included are basic engine maintenance procedures
which can be performed by the operator.
NOTICE: The manufacturers warranty applicable to the engine provides in
part that the provisions of such warranty shall not apply to any engine unit
that has been subject to misuse, negligence or accident. Accordingly,
malfunctions attributable to neglect or failure to follow the manufacturers
fuel or lubricating recommendations may not be within the coverage of the
warranty.
How to Select Lubricating Oil

Refer to DDC-SVC-BRO-0001 for more information.
NOTICE: Lubricating oil must have a sulfated ash level less than 1.0 wt %;
currently referred to as CJ-4 oil.
Detroit PowerGuard oil specification 93K218 or API CJ-4 oils are
recommended for use in the engine.
Detroit currently will allow API CI-4 Plus oil having sulfated ash levels of 1.4%
or less.
10W-30 is the preferred oil for optimal fuel economy results in all DD Platform
engines.
139
How to Procedures
Cold Weather Starting

NOTICE: Monograde oils should not be used in the engine, regardless of
API service classification. Monograde oils gel at lower ambient
temperatures, reducing lubricant flow, and do not provide adequate lubricity
at higher engine operating temperatures resulting in severe engine
damage.
At ambient temperatures below -10C (14F), any low viscosity grade oil approved
per PGOS 93K218 may be used.
The oils must be API CJ-4 and have demonstrated field performance in Detroit
engines. Detroit will allow CI-4 Plus oil having sulfated ash levels of 1.4% or
less.
Use of Synthetic Oils
NOTE: Synthetic oil does not permit extension of recommended oil drain
intervals.
Synthetic oils may be used in Detroit engines provided they are approved by a
POWER GUARD Oil Specification (PGOS). The use of synthetic oils does not
necessarily ensure the extension of the recommended oil drain intervals beyond the
limits.
Use of Supplemental Additives
Lubricants meeting the Detroit specifications outlined in this publication already
contain a balanced additive treatment. Supplemental additives are generally not
necessary and can even be harmful. These additives may be marketed as either oil
treatments or engine treatments and are discouraged from use in Detroit engines.
Engine damage resulting from the use of such materials is not covered by your
Detroit warranty. Detroit will not provide statements beyond this publication
relative to their use.
When to Change Oil

Refer to DDC-SVC-BRO-0001 for more information.
The length of time an engine may operate before an oil change depends upon the
lubricant and fuel used, engine oil consumption, and the operating cycle.
CAUTION: USED ENGINE OIL
To avoid injury to skin from contact with the contaminants in used
engine oil, wear protective gloves and apron.
Oil analysis may be used to determine whether this interval should be shortened,
but it should not be used to lengthen the interval.
140
The use of fuels with sulfur content above 0.05 mass percent will require a
shortening of drain intervals and/or the use of a higher TBN oil.
Disposal of Waste Oil
Used lubricating oil and filters require disposal in an environmentally responsible
manner, according to federal (EPA) and/or state recommendations. The disposal of
waste oil may be best addressed by the engine oil supplier, who may accept
responsibility for proper disposal of this material as part of the business of
providing lubricant.
How to Replace the Lubricating Oil and Oil Filter

The oil filter is an integral part of the lubrication system. Proper filter selection and
maintenance are important to satisfactory engine performance and service life. The
filter should be used to maintain a clean system, not to clean up a contaminated
system. The maintenance intervals for the appropriate duty cycle are listed in tables
in this manual.
Change the oil and replace the lubricating oil filter as follows:
NOTE: If the used oil was contaminated by fuel or coolant, it may be
necessary to take the vehicle to a certified Detroit Service Center. The
Service Center may drain the oil and then remove the oil pan, oil pump, and
oil pump intake manifold to drain the remaining oil held back by the
backflow valve. It is important to remove all contaminated oil from the
engine.
NOTE: Change the engine oil only when the engine oil temperature is
approximately 60C (140F). Changing cold oil will result in extended drain
times.
To avoid injury, never remove any engine component while the
engine is running.
NOTICE: Use care to prevent foreign objects from entering the filter
housing.
2. Clean outside of the oil filter housing.
3. Using a 36-mm socket, unscrew the oil filter cap and filter and allow the oil
to drain into the housing. After draining is complete, remove the assembly
from the housing.
4. Remove the filter element by pressing and twisting the side and detaching it
from the cap.
141
How to Procedures
5. Remove the oil filter O-ring and discard. Lightly coat a new O-ring with
clean engine oil and install it on the filter cap.
6. Check the filter housing for any debris and remove if necessary.
7. Insert a new filter element into the oil filter cap.
8. Insert the filter element and cap assembly into the housing. Torque the cap
to 40 to 50 Nm (30 to 37 lbft).
9. Drain oil from the oil pan as follows:
a. Place a suitable receptacle, 55 L (58 qt) or more, beneath the oil
drain plug on the underside of the oil pan.
b. Carefully unscrew the oil drain plug, and allow the oil to drain out.
c. Discard the plug seal ring.
10. Install the oil pan drain plug with a new O-ring and torque the plug:
a. On a plastic oil pan, torque plug to 45 Nm +/- 7 Nm (33 lbft +/- 5
lbft).
b. On an aluminum oil pan, torque plug to 60 Nm +/- 9 Nm (44 lbft
+/- 6 lbft ).
NOTICE: Do not add oil if the oil reading is between the crosshatch area on
the dipstick. There are approximately 5.0 L (5.2 qt) from the fill mark to the
11. Add new engine oil through the oil fill tube in the following amount; Refer
to section "Engine Oil Capacities". Verify the oil level reading is between
the full and fill marks on the dipstick.
wheels are blocked.
NOTICE: If no oil pressure is shown after approximately 10 seconds, stop
the engine and determine the cause. Running the engine with no oil
pressure could result in engine damage.
12. Start the engine with the accelerator pedal in the idle position (600 rpm).
Monitor the oil pressure gauge or indicator lamp. Keep the engine running
at idling speed (600 rpm) until the oil pressure reading is 10.2 psi (70 kPa)
or more for the DD15/16 and 11.6 psi (80 kPa) or more for the DD13.
142
NOTICE: Do not add oil if the oil reading is between the crosshatch area on
the dipstick. There are approximately 5.0 L (5.2 qt) from the fill mark to the
13. Check the filter housing for signs of leakage.
14. Stop the engine. Check the oil level again per the following guidelines. If
necessary, add oil no more than 5.0 L (5.2 qt) at a time up to the maximum
fill level on the oil dipstick.
How to Select Diesel Fuel

All DD Platform engines are designed to operate on Ultra-Low Sulfur Diesel
(ULSD) fuel.
143
How to Procedures
Quality
NOTICE: Use only Ultra-Low Sulfur Diesel (ULSD) fuel (15 PPM sulfur
content maximum), based on ASTM Standard D 2622 test procedure. Using
fuel other than ULSD will damage the Aftertreatment Device.
Fuel quality is an important factor in obtaining satisfactory engine performance,
long engine life, and acceptable exhaust emission levels. In general, fuels meeting
the properties of ASTM Standard D 975 (grades 1-D and 2-D) have provided
satisfactory performance.
The fuels used must be clean, completely distilled, stable, and non-corrosive. For
more information regarding the significance of these properties and selection of the
proper fuel.
Fuel Contamination
Generally, fuel contamination occurs as the result of improper fuel handling. The
most common types of contamination are water, dirt, and microbial growth "black
slime". The formation of varnishes and gums resulting from poor stability or
extended storage "stale fuel" also affects fuel quality. The best treatment for
contamination is prevention by maintaining a clean storage system and choosing a
reputable fuel supplier.
Supplemental additives are not recommended due to potential injector system
or engine damage. Our experience has been that such additives increase
operating costs without providing benefit.
The use of supplemental fuel additives does not necessarily void the engine
warranty. However, repair expenses which result from fuel system or engine
component malfunctions or damage attributed to their use will not be covered.
Biodiesel 1 General recommendations and guidelines

Detroit supports biodiesel as a renewable fuel. Biodiesel fuels are mono alkali
esters of long chain fatty acids commonly referred to as Fatty Acid Methyl Esters
(FAME) and are derived from renewable resources through a chemical process
called transesterification.
Detroit approves the use of biodiesel fuel blends as follows:
DD Family of Engines - Biodiesel blends up to 5% are allowed
MBE900/4000 Engines - Biodiesel blends up to 5% are allowed
S60 Engines - Biodiesel blends up to 20% are allowed*
*Engines built prior to MY 2004 may contain materials that are not compatible
with biodiesel blends. Biodiesel blends above 5% are not recommended 2.
144
Prohibited Additives
The following fuel additives are not allowed and MUST NOT be mixed with
diesel fuel:
NOTICE: Do not burn used lubricating oil in fuel. It will cause the diesel
particulate filter to prematurely plug with ash.
Used Lubricating Oil Do not use fuel blended with used lubricating oil.
Detroit specifically prohibits the use of used lubricating oil in diesel fuel.
Used lubricating oil contains combustion acids and particulate materials
which can severely erode fuel injector components, resulting in loss of power
and increased exhaust emissions. In addition, the use of drained lubricating
oil will increase maintenance requirements due to filter plugging and
combustion deposits.
WARNING: FIRE
To avoid increased risk of a fuel fire, do not mix gasoline and
diesel fuel.
NOTICE: Detroit will not be responsible for any detrimental effects
resulting from adding drained lubricating oil or gasoline to the diesel fuel.
GasolineThe addition of gasoline to diesel fuel will create a serious fire
hazard. The presence of gasoline in diesel fuel will reduce fuel cetane
number and increase combustion temperatures. Drain and clean tanks which
contain a mixture of gasoline and diesel fuel as soon as possible.
Fuel Additives with Sulfur or Sulfated Ash Do not use non-approved fuel
additives containing sulfur or sulfated ash.
How to Replace the Fuel Filters - Two- and Three-Filter

Systems
NOTICE: If you have just changed the engine oil and filter, you MUST start
the engine and confirm proper oil pressure before changing the fuel filters. If
no oil pressure is shown after approximately 10 seconds, stop the engine
and determine the cause. Running the engine with no oil pressure could
result in engine damage. Start the engine with the accelerator pedal in the
idle position. Monitor the oil pressure gauge or indicator lamp. Keep the
engine running at idling speed until the oil pressure reading is 97 kPa (14
PSI) or more.
NOTE: If you are replacing all fuel filters, it is not necessary to run the
engine and test for leaks after installing each individual fuel filter. However,
if repairing a leak at one filter, complete that repair and test the system for
leaks after priming the fuel system.
145
How to Procedures
Filters are an integral part of the fuel system. Proper filter selection and
maintenance are important to satisfactory engine operation and service life. Filters
should be used to maintain a clean system, not to clean up a contaminated system.
The scheduled maintenance intervals for the appropriate duty cycles are listed in
this manual.
To prevent the escape of high pressure fuel that can penetrate
skin, ensure the engine has been shut down for a minimum of 10
minutes before servicing any component within the high pressure
circuit. Residual high fuel pressure may be present within the
circuit.
NOTICE: At cold temperatures (-40 C or -40 F), DO NOT remove the filter
elements from the caps unless the intent is to replace the filter elements.
Repeated removals at cold temperatures may break the filter element tabs.
Removal of the Fuel Prefilter - Two-Filter System

Remove the prefilter as follows:
1. Using a 36 mm socket, unscrew the prefilter cap.
2. Pull the cap and prefilter straight up and out of the fuel filter housing.
3. Remove the prefilter (1) from the prefilter cap (2) by placing the filter on a
solid surface and apply pressure on prefilter cap (2) at an angle.
4. Discard the prefilter cap seal ring.
146
Installation of the Fuel Prefilter - Two-Filter System

Install the fuel prefilter as follows:
NOTE: If a filter service is being performed, replace all other filters before
priming.
1. Install a new prefilter cap seal ring on to the prefilter cap.
2. Snap new prefilter into the prefilter cap.
3. Apply a thin coat of petroleum-based lithium grease to the prefilter cap seal
ring and the prefilter seals (1).
4. Install the prefilter into the fuel filter module.

5. Turn the cap counterclockwise until a click sound is made, then turn
clockwise and hand tighten.
6. Torque prefilter cap to 55-60 Nm (41-44 ftlb).
7. Once all required filters have been changed, prime the fuel system using the
ESOC 350, J-47912 or the engine mounted hand primer.
wheels are blocked.
147
How to Procedures
oil pressure gauge or indicator lamp. Maintain the engine running at idle
until a stable oil pressure reading of 97 kPa (14 psi) or more is maintained
for one minute.
9. Check for leaks.
10. Allow the engine to reach operating temperature of 60C (140F).
13. Check for leaks.
Removal of the Water Coalescer/Final Filter - 2-Filter System

Remove the water coalescer/final filter as follows:
NOTICE: Do not tilt the water coalescer/final filter when removing it from
the housing. Possible damage to the water coalescer/final filter or stand
pipe may occur.
1. Using a 36mm socket, unscrew the water coalescer/final filter cap.
2. Pull the cap and water coalescer/final filter straight up and allow the fuel to
drain back.
3. Remove the water coalescer/final filter (2) from the water coalescer/final
filter cap (1) by placing the filter on a solid surface with the drain back plug
location at 12 oclock (3) and apply pressure on the water coalescer/final
filter cap at an angle.
148
4. Discard the water coalescer/final filter.

5. Inspect inside the housing for any large debris, clean housing as needed.
6. Discard water coalescer/final filter cap seal ring.
Installation of the Coalescer/Final Filter - Two Filter System

Install the water coalescer/final filter as follows:
NOTE: If a fuel filter service is being performed, replace all other fuel filters
before priming the fuel system.
1. Install a new seal ring on to water coalescer/final filter cap.
2. Snap a new water coalescer/final filter into the water coalescer/final filter
cap.
3. Apply a light coat of Parker super O-lube or petroleum-based lithium grease
to the water coalescer/final filter cap seal ring and drain back plug seal ring
(C).Apply a heavy coat of Parker super O-lube or petroleum-based lithium
grease to the upper (A) and lower seals (B) on the water coalescer/final filter.
149
How to Procedures
The illustration below shows the proper amount of lubricant to use on

the upper and lower seals.
4. Install the water coalescer/final filter into the fuel filter module.
150
NOTE: Viewing the fuel filter module from the top, the drain back port is
located at 10 o'clock.
5. Turn the water coalescer/final filter cap counterclockwise until the
drain back plug has located the drain back port. Apply light pressure to
the top of the water coalescer/final filter cap to seat the drain back plug into
the drain back port, hand tighten the filter cap by turning the cap clockwise.
6. Torque water coalescer/final filter cap to 55 to 60 Nm (41 to 44 lbft).
ESOC 350, J-47912 or the engine-mounted hand primer.
wheels are blocked.
oil pressure gauge or indicator lamp. Keep the engine running at an idling
speed until a stable oil pressure reading of 97 kPa (14 psi) or more is
maintained for one minute.
9. Check for leaks.
10. Allow the engine to reach operating temperature of 60C (140F).
and then shut down the engine.
Removal of the Final Filter - Three-Filter System

Remove the final filter as follows:
NOTICE: Do not tilt the final filter when removing it from the housing.
Possible damage to the final filter or stand pipe may occur.
1. Using a 36-mm socket, unscrew the final filter cap.
2. Pull the cap and final filter straight up and allow the fuel to drain back.
151
How to Procedures
3. Remove the final filter (2) from the final filter cap (1) by placing the filter
on a solid surface and apply pressure on the final filter cap at an angle.
4. Discard the filter.

5. Inspect inside the housing for any large debris and clean if needed.
6. Discard final filter cap seal ring.
Installation of the Final Filter - Three-Filter System

Install the final filter as follows:
1. Install a new final filter cap seal ring.
2. Snap new final filter into the final filter cap.
3. Apply a light coat of petroleum-based lithium grease to the cap seal ring (1)
and to the lower seal on the final filter.
152
4. Install the final filter into the fuel filter module.

5. Turn the cap counterclockwise until a "click" sound is made, then turn
6. Torque final filter cap to 55-60 Nm (40-44 lbft).
wheels are blocked.
8. Start the engine refer to Routine engine start, with the accelerator pedal in
the idle position. Monitor the oil pressure gauge or indicator lamp. Keep the
engine running at a idling speed until a stable oil pressure reading of 97 kPa
(14 psi) or more is maintained for one minute.
9. Check for leaks.
10. Allow the engine to reach operating temperature of 60 C (140 F).
11. Increase engine speed to 1800 RPM for three minutes.
153
How to Procedures
Removal of the Prefilter - 3-Filter System

Remove the prefilter as follows:
NOTICE: Do not tilt the prefilter when removing it from the housing.
Possible damage to the prefilter or stand pipe may occur.
1.
2.
3.
4.
Using a 36 mm socket, unscrew the prefilter cap.

Pull the cap and prefilter straight up and out of the fuel filter housing.
Remove the prefilter from the prefilter cap and discard.
Discard the prefilter cap seal ring.
Installation of the Prefilter - 3-Filter System

Install the prefilter as follows:
NOTE: The prefilter should snap into the cap in two positions. The tabs (3)
should align with the slot in the prefilter cap (5).
1. Snap new prefilter (4) into the prefilter cap (1).
2. Apply a thin coat of petroleum-based lithium grease to the prefilter cap seal
ring (2).
3. Apply a thin coat of petroleum-based lithium grease to the inside and
outside of the prefilter bottom seal.
4. Install the prefilter into the fuel filter module.
154
6. Torque prefilter cap to 15-20Nm (11-15 lbft).
wheels are blocked.
8. Start the engine ( Refer to section "Routine Engine Start") with the
accelerator pedal in the idle position. Monitor the oil pressure gauge or
indicator lamp. Keep the engine running at a idling speed until a stable oil
pressure reading of 97 kPa (14 psi) or more is maintained for one minute.
9. Check for leaks.
NOTE: Increasing engine speed above idle before oil pressure has
Removal of the Water Separator/Coalescer - Three-Filter System

Remove the water separator/coalescer as follows:
NOTICE: Do not tilt the water separator/coalescer when removing it from
the housing. Possible damage to the water separator/coalescer or stand
pipe may occur.
1. Using a 36mm socket, unscrew the water separator/coalescer cap.
2. Pull the cap and water separator/coalescer straight up and allow the fuel to
drain back.
3. Remove the water separator/coalescer (1) from the Water Separator/
Coalescer cap (2) by placing the filter on a solid surface and apply pressure
on the Water Separator/Coalescer cap at an angle.
155
How to Procedures
4. Discard the filter.

5. Inspect inside the housing for any large debris and clean it out if needed.
6. Discard Water Separator/Coalescer cap seal ring.
Installation of the Water Separator/Coalescer - Three-Filter

System
Install the water separator/coalescer as follows:
1. Snap a new water separator/coalescer into the Water Separator/Coalescer
cap.
2. Install a new Water Separator/Coalescer cap seal ring.
3. Apply a light coat of petroleum-based lithium grease to the Water Separator/
Coalescer cap seal ring and to the lower seal (1) on the water separator/
coalescer filter.
156
4. Install the water separator/coalescer into the fuel filter module.

6. Torque water separator/coalescer cap to 55-60 Nm (41-44 ftlb).
wheels are blocked.
8. Start the engine refer to Routine engine start with the accelerator pedal in
the idle position. Monitor the oil pressure gauge or indicator lamp. Keep the
engine running at a idling speed until a stable oil pressure reading of 14 psi
(97 kPa) or more is maintained for one minute.
9. Check for leaks.
157
How to Procedures
Engine Out of Fuel How to Restart

When an engine has run out of fuel, there is a definite procedure to follow when
restarting it.
NOTICE: Never use the starting motor and fuel pump to prime the fuel
filters. Prolonged use of the starting motor and fuel pump to prime the fuel
system can result in damage to the starter, fuel pump, and injectors.
Use the following procedure to prime the fuel system:
NOTE: If a vehicle is on uneven ground, more fuel may be required.
1. Fill the fuel tank with the recommended grade of fuel. If only partial filling
is possible, add a minimum of 10% of the total tank volume of fuel to the
tank. For example, a 150-gallon tank would require a minimum of 15
gallons of fuel.
2. Connect ESOC 350 (J-47912) or operate the engine mounted hand primer
for three minutes or 250 strokes.
3. Turn on the ignition switch.
4. Wait for the engine system indicator lights on the instrument panel to go
out.
5. With the accelerator pedal in the idle position, start the engine.
6. Crank engine for 20 seconds.
NOTE: The starting cycle can be repeated up to three times.
7. If engine does not start, allow for a 60-second cool down and repeat
previous step.
8. Monitor the oil pressure gauge or indicator lamp. Keep the engine running
at an idling speed until a stable oil pressure reading of 97 kPa (14 psi) or
more is maintained for one minute.
9. Check for leaks.
158
14. If engine still fails to start, contact an authorized Detroit repair facility.
How to Clean an Engine

Observance of all environmental protection regulations is required. Use highpressure equipment as follows:
CAUTION: EYE INJURY
To avoid injury from flying debris, wear a face shield or goggles.
NOTICE: To prevent damage to engine components, keep the water
moving at all times while cleaning. Never direct water onto electrical
components, plug connectors, seals or flexible hoses.
Information on suitable cleaning and protective products is available from any
authorized dealer. Note the equipment manufacturer's operating instructions.
Use the following minimum working distance between the high-pressure nozzle
and the surface being cleaned:
Approximately 28 in. (700 mm) for circular pattern jets
Approximately 12 in. (300 mm) for 25-degree flat jets and dirt cutters
Power clean the engine as follows:
1. Allow engine to cool down to room temperature before spraying the engine.
NOTICE: Avoid all of the electrical connections with direct water or steam
spray or damage can result.
2. Thoroughly clean the entire engine using a steam cleaner or high pressure
washer with mild soap and warm water.
WARNING: EYE INJURY
NOTE: Do not use compressed air or pressurized water to clean or dry the
engine if any part of the engine is disassembled.
3. Once the engine is clean, blow the electrical connectors dry with
compressed air to remove most of the standing water.
4. Allow the engine to dry completely before making any kind of repair.
159
How to Procedures
5. When reassembling, ensure that there is no standing water in any electrical

connectors before seating the plug.
Cleaning/Flushing the Cooling System

Collect the used coolant, cleaning solutions, and washing liquids and dispose of
them in an environmentally responsible manner.
Degrease as follows:
1. First remove debris (such as dust, insects) from the fins of the radiator grille.
WARNING: EYE INJURY
NOTICE: Clean at moderate air pressures only to avoid damaging the
radiator grille fins.
2. Remove the debris by blowing them through with compressed air or
spraying them out with water. Work from the rear of the radiator (in the
opposite direction of the normal cooling air flow).
3. Drain the coolant when the engine is cold. Refer to section "Cooling System
Drain Procedure". For detailed procedures, see the vehicle/chassis
maintenance manual. For types of coolant, refer to the How to Select
Coolant section for the listing of required intervals using the recommended
coolants.
4. If the HVAC unit is connected to the cooling system, open the regulating
valves all the way.
5. Fill the cooling system with a 5% solution (1.6 ounces per quart [50 grams
per liter] of water) of a mildly alkaline cleaning agent. Refer to section
"Coolant Selections and Maintenance".
6. Run the engine at moderate speed until the thermostat starts to open. The
thermostat starts to open at 88C (190F) and is fully open at 95C (203F).
Then run it for about five minutes longer. Shut down the engine and allow it
to cool to approximately 50C (112F).
7. Drain all the cleaning solution.
160
8. Flush the cleaning solution from the cooling system.

a. Immediately after draining the cleaning solution, flush the system
with clean water.
b. Once the clean water has drained, fill the system again with clean
water.
c. Run the engine at moderate speed until the thermostat starts to open.
The thermostat starts to open at 88C (190F) and is fully open at
95C (203F). Then run it for about five minutes longer. Shut down
the engine and allow it to cool to approximately 50C (112F).
d. Drain the hot water.
9. Fill the cooling system with new coolant. For detailed procedures, see the
vehicle/chassis maintenance manual. For types of coolant, refer to the How
to Select Coolant section for the listing of required intervals using the
Coolant Selections and Maintenance

Coolant Selections and Maintenance
This section covers selection of the required coolant for the engine.
Extended Life Coolants
Extended Life Coolant (ELC) contain Organic Acid Technology (OAT) which
provide corrosion protection and inhibit liner cavitation. These coolants require less
maintenance over the useful life of the engine.
ELC antifreeze coolants are commercially available from Detroit (recommended)
and other manufacturers as either concentrated or pre-mixed formulations.
Concentrated antifreeze coolants should be mixed at 50% (50% antifreeze/50%
water). All ELC's used must also meet Detroit 93K217 specification. Detroit
requires that these types of coolants to be free of nitrite and phosphate. Detroit
has found that ELC's containing nitrite may lead to a breakdown of the coolant and
subsequent damage to the cooling system.
These types of coolants should not be mixed with Standard Life Coolants. If an
ELC antifreeze coolant and SLC antifreeze coolants are mixed, damage may not
result, but the long-life advantages of the ELC antifreeze coolant will be lost. In
this event, the coolant should be re-inhibited with OAT inhibitors and confirmed by
analysis or else it must be maintained as an SLC antifreeze coolant.
SLC Antifreeze Coolants
Standard Life Coolant (SLC) contain inhibitor salts, including nitrites, to prevent
liner cavitation. These coolants require interval testing to maintain inhibitor
concentration.
161
How to Procedures
SLC antifreeze coolants are commercially available from Detroit (recommended)

and other manufacturers as either concentrated or as pre-mixed antifreeze.
Concentrated antifreeze coolants should be mixed at 50% (50% antifreeze/50%
water). All fully formulated coolants used must also meet Detroit 93K217
specification.
NOTE: Fully formulated antifreeze does not require a dosage of
Supplemental Coolant Additive (SCA) at initial use.
Coolant Fill Options

The coolants recommended for use in Detroit engines are listed in Table "HDEP
Coolant Fill Options". This publication will give a complete explanation of their
use.
NOTICE: Required specifications for water, Ethylene Glycol (EG),
Propylene Glycol (PG), inhibitor packages, and inhibitor concentration are
included in the appendix of this publication. To avoid possible engine
damage from inadequate or over-concentrated coolant, this publication
should be read thoroughly before replacing or topping-off coolant.
162
Table 24.
HDEP Coolant Fill Options
Engine Series
Product
Ethylene Glycol based

antifreeze coolant + SLC
corrosion inhibitors
Detroit Power Cool or refer to

93K217
list of approved coolants at
DDCSNDDC.Freightliner.com
Propylene Glycol based

No Detroit product
available. Refer to
93K217 list of approved
coolants at

antifreeze coolant + ELC
inhibitors
Detroit Power Cool Plus or

refer to
coolants at

inhibitors
No Detroit product
available. Refer to
coolants at
DD13, DD15, DD16
163
How to Procedures
Table 25.
Legacy Engine Coolant Fill Options
Engine Series
Series 50, Series 55,

Series 60, MBE900,
MBE4000
1Water-only
Product

Detroit Power Cool or refer to

93K217
list of approved coolants at

No Detroit product
available. Refer
to 93K217 list of approved
coolants at
Water based coolant + SLC

corrosion inhibitors 1
Deionized Water + Detroit

Genuine
Coolant 3000

inhibitors
Detroit Power Cool Plus or

refer to
coolants at

inhibitors
No Detroit product
available. Refer
to 93K217 list of approved
coolants at
Water based coolant + ELC

inhibitors 1
Deionized Water + Detroit

Genuine
Coolant Plus 6000
coolant systems offer no freeze protection and should not be used where
ambient temperatures can fall to 0C (32F).
Additional approved coolant products can be found on the Detroit 93K217 list at
DDCSN-DDC Freightliner.com (https://ddcsn-ddc.freightliner.com/cps/rde/xchg/
ddcsn/).
Coolants for Detroit Engines

Coolants for Detroit Engines
The intent of this bulletin is to provide the requirements, directions, and
information required to ensure cooling system protection for Detroit engines.
These recommendations are general rules and reflect years of experience,
technology research, and product development. Specific concerns not covered by
164
this publication should be addressed to your local Detroit representative. The

coolant used in Detroit engines must meet Detroit 93K217 Specifications with
the following basic requirements:
Provide an adequate heat transfer medium.

Protect against cavitation damage to both cylinder liners and water pumps.
Provide a corrosion/erosion-resistant environment.
Prevent formation of scale or sludge deposits.
Be compatible with cooling system hose and seal materials.
Provide adequate freeze protection.
The rest of this section will describe the requirements for the proper usage of the
water, antifreeze, and corrosion inhibitors. It will also describe the coolants and
additives that are not recommended by Detroit and have been proven harmful to
Detroit engines.
Coolants NOT Permitted

The following coolants are not to be used in Detroit engines:
Automotive/Passenger car-type coolants must not be used in Detroit engines
because they offer no liner pitting protection. Also, these types of coolants
generally contain high levels of phosphates and silicates.
Methyl alcohol-based antifreeze must not be used in Detroit engines because
of its effects on the nonmetallic components of the cooling system and its low
boiling point.
Methoxy propanol-based antifreeze must not be used in Detroit engines
because it is not compatible with fluorocarbon elastomer seals found in the
cooling system.
Glycol-based coolants formulated for Heating/Ventilation/Air Conditioning
(HVAC) must not be used in Detroit engines. These coolants generally
contain high levels of phosphates, which will form deposits on hot internal
engine surfaces, reduce heat transfer, and cause water pump seal leaks.
Waterless-type coolants must not be used.
Nitrite Organic Acid Technology (NOAT)must not be used in Detroit
engines because with poor maintenance components become more vulnerable.
Non-Formulated Additives NOT Permitted

The following additives should not be used in Detroit engines:
Soluble Oils: Soluble oil additives are not approved for use in Detroit engine
cooling systems. A small amount of oil adversely affects heat transfer. For
example, a 1.25% concentration of soluble oil increases the fire deck temperature
6%. A 2.50% concentration increases the fire deck temperature 15%. The use of
soluble oil additives may result in engine overheating and/or failure.
Chromates: Chromate additives are not approved for use in Detroit engine
cooling systems. Chromate additives can form chromium hydroxide, commonly
called green slime. This, in turn, can result in engine damage due to poor heat
165
How to Procedures
transfer. Cooling systems operated with a chromate-inhibited coolant must be

chemically cleaned with Detroit Genuine Coolant Twin Pack cooling system
cleaner/conditioner (or equivalent sulfamic acid/sodium carbonate cleaner) and
flushed.
Phosphate Inhibitors: Phosphate has tendency to form deposits on surfaces
transferring high heat which ultimately affect cooling capabilities. Phosphate
deposits on water pump seals will result in coolant leakage across seal faces.
Maintenance
Maintenance
This section describes procedures needed to maintain the proper coolant level and
concentration.
Topping Off Coolant

The coolant level should be checked daily and at each service interval. If topping
off is necessary, add coolant which is identical to the initialfill coolant. ELCs
should be topped-off with a coolant of the same formulation; SLCs should also be
topped-off with a coolant of the same formulation.
Coolant Maintenance Intervals

Required Service Intervals
166
Table 26.
Extended Life Coolant:
Service
Application
Long Haul 1
Short Haul 2
Every 160,000
km (100,000
miles) or 1 year
Every 112,000
km (70,000
miles) or 1 year
Severe 3
Action
Required
Every 80,000 km
(50,000 miles) or
1 year 4
Refer to section
"Extended Life
Coolant Additive
Maintenance
Procedures"
Engine Series
Series 40, 50,
60
MBE4000,
MBE900
DD13, DD15,
DD16
1. Long Haul (over-the-road transport) service applies to vehicles that annually travel more
than 96,000 km (60,000 miles) and average greater than 6 miles per gallon with minimal city
stop-and-go operation.
2. Short Haul service applies to vehicles that annually travel up to 48,000-96,000 km
(30,000-60,000 miles) and average between 5.1 and 5.9 miles per gallon.
3. Severe service applies to vehicles that annually travel up to 48,000 km (30,000 miles) and
average less than 5 miles per gallon or that operate under severe conditions. Severe service
also applies to RV applications. Service applies to vehicles that annually travel up to 48,000
km (30,000 miles) or that operate under severe conditions. Only one of these conditions
needs be met to categorize an application as Severe Service.
4. Whichever comes first
167
How to Procedures
Table 27.
Standard Life Coolant:
Service
Application
Long Haul 1
Short Haul 2
Severe 3
Engine Series
Series 40, 50,
60
Every 32,000 km Every 24,000 km

Every 48,000 km
(20,000 miles) or (15,000 miles) or
(30,000 miles) or
500h, or 6
300h, or 3
4
1 year
months 4
months 4
MBE4000,
MBE900

Every 48,000 km
(30,000 miles) or
500h, or 6
300h, or 3
1 year 4
months 4
months 4
DD13, DD15,
DD16
Every 40,000 km
(25,000 miles) or
640h, or 6
4
4
1 year
895h, or 1 year
months 4
Action
Required
Refer to section
"Standard Life
Coolant Additive
Maintenance
Procedures"
1. Long Haul (over-the-road transport) service applies to vehicles that annually travel more
than 96,000 km (60,000 miles) and average greater than 6 miles per gallon with minimal city
stop-and-go operation.
2. Short Haul service applies to vehicles that annually travel up to 48,000 to 96,000 km
(30,000 to 60,000 miles) and average between 5.1 and 5.9 miles per gallon.
3. Severe service applies to vehicles that annually travel up to 48,000 km (30,000 miles) and
average less than 5 miles per gallon or that operate under severe conditions. Severe service
also applies to RV applications. Service applies to vehicles that annually travel up to 48,000
km (30,000 miles) or that operate under severe conditions. Only one of these conditions
needs be met to categorize an application as Severe Service.
4. Whichever comes first.
Table 28.
Coolant Drain interval:
Engine Series
ELC
SLC
965,606 km (600,000 miles),

4 years or engine overhaul
482,803 km (300,000 miles)

or 2 years
Series 60, 50, 40

MBE4000, MBE900
DD13, DD15, DD16
Extended Life Coolant Additive Maintenance Procedures

The concentration of ELC corrosion inhibitors will gradually deplete, at a much
slower rate than SLC corrosion inhibitors, during normal engine operation.
Corrosion inhibitor limits are established by the coolant manufacturer. Therefore
Detroit recommends following the manufacturers recommendations as to
minimum and maximum limits.
168
Freeze Point Check

To best measure the quality of anti-freeze coolant, a check of the freeze point
(glycol concentration), by refractometer, should be performed at each service
interval to ensure anti-freeze levels are within specification. Detroit requires a
freeze point of -34F (+/-10F) to guarantee optimal engine protection. The
exception would be certain regions that require a freeze point of -60F to protect
against colder climates.
Laboratory Testing
Laboratory testing is the best practice for determining ELC coolant quality and will
provide vital information regarding the engine performance. A factory coolant
analysis program is available through authorized Detroit service outlets. To
verify coolant acceptability, submit a sample for coolant analysis according to
Table "Extended Life Coolant".
However, a laboratory meeting ISO 17025 requirements may be used in place of
the Detroit Genuine Parts Program laboratory.
OAT Detection Strips
OAT Detection Strips that monitor the organic acid levels can be used to test the
concentration of corrosion inhibitors in the anti-freeze coolant. Detroit
recommends consultation with your coolant manufacturer's technical representative
for proper application.
ELC Enhancers/Extenders
ELC enhancers/extenders can be used to extend the life of the coolant. These
products should be added to your anti-freeze coolant when corrosion inhibitors fall
below manufacturer's recommendations. Detroit recommends consultation with
your coolant manufacturer's technical representative for proper application.
Drain, Flush, and Refill Procedure (See Appendix C for Product Part
number)
When coolant has reached the end of life, it is recommended to properly clean your
cooling system of any scale, deposits or any other contaminants that may reduce
the efficiency of the heat transfer. The coolant must be drained completely
including the block, radiator, and HVAC system. Next, flush the system with fresh,
clean water. Replace drain fittings. Mix required amount of Penray 2010 cleaner in
a 5-gallon pail of water and pour into radiator inlet. Fill system completely with
clean water. Re-circulate cleaning solution by idling engine for 2 hours after top
hose is hot. Temperature should be 88 to 95C (190 to 203F) to allow the
thermostat to open.
Drain cleaning solution from the system. The radiator, block and HVAC system
must both be drained. Flush with clean water (through the radiator inlet) for 3 to 5
minutes. Replace drain fittings. Mix required Penray 2011 in a 5-gallon pail and
pour into radiator inlet (1 pound per 4 gallons cooling system capacity). Fill system
completely with clean water. Re-circulate the Penray 2011 conditioning solution by
169
How to Procedures
idling engine for 15 minutes after the top hose is hot (thermostat opens if it wasnt
removed). Drain the Penray 2011 solution from the system. The radiator, block
and HVAC system must both be drained. Flush with clean water for 3-5 minutes.
Keep flushing as long as water looks rusty or turbid. Replace drain fittings.
Recharge cooling system with the appropriate ratio of clean water and the proper
antifreeze for your application.
Standard Life Coolant Additive Maintenance Procedures

The concentrations of SLC inhibitors will gradually deplete during normal engine
operation. SCAs replenish the protection for cooling system components and must
be added to the cooling system on an as needed basis. Below are test procedures
that will assist in determining the inhibitor concentration.
Coolant Test Procedure
3-Way Test Strips
Nitrite concentration is an indication of the overall coolant inhibitor concentration
in SLC formulations. These coolants must be tested for nitrite concentration at the
regular intervals as listed in Table "Standard Life Coolant". Detroit Genuine
Fluid Analysis 3-Way Test Strips (or equivalent) are recommended. Use these test
strips to measure nitrite and glycol concentrations. Cavitation/corrosion protection
is indicated on the strip by the level of nitrite concentration. Freeze/boil-over
protection is determined by glycol concentration.
Laboratory Testing
As an alternative to the test strips, a factory coolant analysis program is available
through authorized Detroit service outlets. To verify coolant acceptability,
submit a sample for coolant analysis according to Table "Standard Life Coolant".
Drain, Flush, and Refill Procedure (See Appendix C for Product Part
Number)
When coolant has reached the end of life, it is recommended to properly clean your
cooling system of any scale, deposits or any other contaminants that may reduce
the efficiency of the heat transfer. The coolant must be drained completely
including the block, radiator, and HVAC system. Next, flush the system with fresh,
clean water. Replace drain fittings. Mix required amount of Penray 2010 cleaner in
a 5-gallon pail of water and pour into radiator inlet. Fill system completely with
clean water. Re-circulate cleaning solution by idling engine for 2 hours after top
hose is hot. Temperature should be 88 to 95C (190 to 203F) to allow the
thermostat to open.
Drain cleaning solution from the system. The radiator, block and HVAC system
must both be drained. Flush with clean water (through the radiator inlet) for 3 to 5
minutes. Replace drain fittings. Mix required Penray 2011 in a 5-gallon pail and
pour into radiator inlet (1 pound per 4 gallons cooling system capacity). Fill system
170
completely with clean water. Re-circulate the Penray 2011 conditioning solution by
idling engine for 15 minutes after the top hose is hot (thermostat opens if it wasnt
removed). Drain the Penray 2011 solution from the system. The radiator, block
and HVAC system must both be drained. Flush with clean water for 3-5 minutes.
Keep flushing as long as water looks rusty or turbid. Replace drain fittings.
Recharge cooling system with the appropriate ratio of clean water and the proper
antifreeze for your application.
Supplemental Coolant Additives (SCA)
Supplemental Coolant Additive (SCA) Solutions- for Ethylene or
Propylene Glycol-based Antifreeze Coolants
The coolant must be maintained with the proper concentration of corrosion
inhibitors. As the concentration of inhibitors deplete, additional SCA must be
added to the coolant as indicated by a nitrite concentration of 900 PPM, or less. If
the nitrite concentration is greater than 900 PPM, do not add additional SCA. If the
nitrite concentration is above 3200 PPM, the system is over-inhibited. The system
should be partially drained and filled with a 50/50 mix of water and EG or PG.
Supplemental Coolant Additive (SCA) Solutions - for Water-based
Coolants (Legacy Engines Only)
In warm climates where freeze protection is not required, water only with corrosion
inhibitors is approved for use. Water-only systems need to be treated with the
proper dosage of corrosion inhibitors. Detroit approved conventional SCA or
OAT corrosion inhibitors must be added to the water to provide required corrosion
and cavitation erosion protection.
Need-Release Coolant Filters (FOR STANDARD LIFE COOLANT ONLY
1)
Need-Release coolant filters are available for Series 50, Series 60 and pre-2016 DD
series engines. Membranes in the filters release SCAs before the coolant
approaches a corrosive condition, protecting the engine from corrosion. The needrelease elements release the SCA charge as needed, as opposed to the maintenance
SCA elements, which instantaneously release the SCA charge. Need-release
coolant filter elements should be replaced after one year or 160,000 km (100,000
miles), or 3,000 operating hours, whichever comes first.
1. Need-Release filters are not to be used with ELC type coolants. Such use will
cause serious damage to the engine.
Appendix A - Definitions
Appendix A - Definitions
Antifreeze:
171
How to Procedures
A substance that is added to the water in a vehicles cooling system that lowers the
freeze point to prevent freezing. The two most common antifreezes are ethylene
glycol (EG) and propylene glycol (PG).
Coolant:
A fluid that transfers heat from the engine by circulation.
Extended Life Coolant (ELC): AKA - Long-Life Coolant or Organic Acid
Technology:
These types of coolants have been formulated to extend the service interval of the
coolant. Example of ELC is Power Cool Plus.
Fully Formulated:
Antifreeze that contains all the necessary inhibitors to protect a diesel engine and
does not, therefore, require a pre-charge of Supplemental Coolant Additive before
its first use.
Initial-Fill:
The coolant that is used in a new or rebuilt engine, or used any time the cooling
system is emptied and then refilled with new coolant.
Standard Life Coolant (SLC): AKA - Fully-Formulated or Conventional
Coolant:
These types of coolants use supplemental coolant additives (SCA) to protect
against corrosion or mechanical wear. Example of SLC is Power Cool.
Supplemental Coolant Additive:
An additive used in a preventive maintenance program to prevent corrosion,
cavitation, and the formation of deposits.
Appendix B - General Coolant Information

Appendix B - General Coolant Information
SLC Antifreeze Coolants
These products are available as Fully Formulated and Phosphate-Free. They are
commercially available from Detroit (recommended) and other manufacturers as
either concentrated antifreeze or as pre-mixed antifreeze. The pre-mixed antifreeze
is ready to use, while the concentrated coolant must be mixed with water prior to
use. All fully formulated coolants used must also meet Detroit 93K217
specification.
NOTE: Fully formulated antifreeze does not require a dosage of
Supplemental Coolant Additive (SCA) at initial use.
172
ELC Antifreeze Coolants

EG and PG based antifreeze coolants contain Organic Acid Technology (OAT).
These coolants require less maintenance over the useful life of the engine.
ELC antifreeze coolants are available as either concentrated or pre-mixed
formulations. Concentrated antifreeze coolants should be mixed at 50% (50%
antifreeze/50% water). These types of coolants should not be mixed with SLCs.
If an ELC antifreeze coolant and SLC antifreeze coolants are mixed, damage may
not result, but the long-life advantages of the ELC antifreeze coolant will be lost. In
this event, the coolant should be re-inhibited with OAT inhibitors and confirmed by
analysis or else it must be maintained as an SLC antifreeze coolant.
Water-Only Coolants (Series 50, 55 and 60 only)
In warm climates where freeze protection is not required, water only with corrosion
inhibitors is approved for use. Water-only systems need to be treated with the
proper dosage of corrosion inhibitors. Detroit-approved SCA or ELC corrosion
inhibitors must be added to the water to provide required corrosion and cavitation
erosion protection.
Mixing Ethylene Glycol or Propylene Glycol Antifreeze and Water
It is highly recommended to use a pre-mixed 50/50 antifreeze coolant. However, if
a concentrated Ethylene Glycol or Propylene Glycol antifreeze is purchased, mix
the antifreeze with water meeting the required quality standards and fill the cooling
system. See water requirement below for quality standards. If a pre-diluted coolant
is purchased, simply fill the cooling system.
For best overall performance, a coolant consisting of 50% concentration of
antifreeze (50% antifreeze, 50% water) is recommended. An antifreeze
concentration of over 60% (60% antifreeze, 40% water) is not recommended due
to poor heat transfer, reduced freeze protection, and possible silicate dropout. An
antifreeze concentration below 40% (40% antifreeze, 60% water) offers too little
freeze and/or corrosion protection and is not recommended.
WATER REQUIREMENTS
Distilled or de-ionized water, which eliminates the adverse effects of minerals in
tap water, is preferred. High levels of dissolved chlorides, sulfates, magnesium, and
calcium in some tap water causes scale deposits, sludge deposits and/or corrosion.
These deposits have been shown to result in water pump failures and poor heat
transfer, resulting in overheating. If tap water is used, the mineral content in the
water must be below the maximum concentration listed in the table below.
173
How to Procedures
Table 29.
Maximum Mineral Concentration in Water
Minerals
Maximum Concentration
Parts per Million
Grains per Gallon
Chlorides
40
2.5
Sulfates
100
5.8
Total Dissolved Solids
340
20
Magnesium + Calcium
Content
170
10
Figure 37. Procedure To Evaluate The Quality Of Water

Recycled Antifreeze
Antifreeze coolant made with ethylene or propylene glycol recycled by reverse
osmosis, distillation, and ion exchange and properly re-inhibited to meet ASTM
D6471 or D6472 requirements has been demonstrated to provide service equivalent
to virgin antifreeze. Recycled antifreeze coolants of these types are preferred.
However, suppliers of these recycled glycols must provide evidence the product is
free of contaminates listed below:
Acetates
Acetone
Ammonia
Boron
Ethanol
Formates
Glycolates
Ketones
Nitrate
174
Nitrite
Phenols
Phosphorus
Silicon
Toluene
Other recycled coolants, especially coolants recycled through filtration processes,

are not recommended.
Appendix C - Detroit Cooling System Maintenance

Products
Appendix C - Detroit Cooling System Maintenance Products
Table 30.
Detroit Extended Life Coolant (Ethylene Glycol-based)
Coolant Type
Concentrate
Pre-Diluted (50:50)
Part Number
Description
OWI 23539616
One Gallon Jug - 4 Per Case

(Canada)
OWI 23519397
One Gallon Jug- 6 Per Case
OWI 23519394
55-Gallon Drum
OWI 2359617

(Canada)
OWI 23519396
OWI 23519398
55-Gallon Drum
OWI 2359084
275-Gallon Tote (Canada)
Table 31.
Detroit Genuine Coolant Plus Extender (for use with Detroit Genuine Coolant Plus)
Coolant Type
Part Number
Description
IEG Detroit Genuine

Coolant; Series 50 and
Series 60
OWI 23519400
One Quart Bottle - 6 Per

Case
175
How to Procedures
Table 32.
Detroit Standard Life Coolant (Ethylene Glycol-based)
Coolant Type
Concentrate
Pre-Diluted (50:50)
Part Number
Description
OWI 23539622

(Canada)
OWI 23512138
OWI 23512139
55-Gallon Drum
OWI 23513503
Bulk Delivery - 1000 Gallon

min.
OWI 23539623

(Canada)
OWI 23528203
OWI 23518918
55-Gallon Drum
OWI 23538603
275-Gallon Tote
Table 33.
Detroit Genuine Coolant 2000 Supplemental Coolant Additives (SCA)
Coolant Type
IEG Detroit Genuine
Coolant
Part Number
Description
PIC 23507858
Pint Bottle - 12 Per Case
PIC 23507860
5-Gallon Pail
PIC 23507861
55-Gallon Drum
Table 34.
Detroit Genuine Coolant 3000 SCAs
Coolant Type
IEG Detroit Genuine

Coolant
176
Part Number
Description
PIC 23507854
Pint Bottle - 12 Per Case
PIC 23507855
Half Gallon Jugs - 6 Per

Case
PIC 23507856
5-Gallon Pail
PIC 23507857
55-Gallon Drum
Table 35.
Detroit Genuine Coolant 3000 SCA Filters (Series 50 and Series 60 Engines Only)
Coolant Type
IEG Detroit Genuine

Coolant
Part Number
Description
23507545
4 Ounce (1 Pint Equivalent)
23508425
23508426
23507189
23508427
23508428
53 Ounce (13 Pint

Equivalent)
Table 36.
Detroit Genuine Coolant Cooling System Cleaners
Coolant Type
Part Number
All Types
PIC 201549
Twin pack - 2 Per Case
PIC 200164
One-Half Gallon Jug - 6 Per

Case
PIC 200105
5-Gallon Pail
PIC 200155
55-Gallon Drum
Standard Life Coolant Only
Description
Table 37.
Detroit Genuine Fluid Analysis Products
Coolant Type
Part Number
Description
Standard Life Coolant
DDE 23516921
U.S. SLC Test Kit
Extended Life Coolant
DDE 23539088
U.S. ELC Test Kit
How to Replace the Coolant Filter

2014 model year engines and earlier are equipped with a coolant filter.
NOTE: In addition to the cleaning procedure, other components of the
cooling system should be checked periodically to keep the engine operating
at peak efficiency.
Service the cooling system as follows:
177
How to Procedures

NOTE: Change the coolant filter only after the vehicle has cooled and no
residual pressure is present.
NOTE: Use care to prevent foreign objects from entering the filter housing.
2. Clean outside of the coolant filter housing.
3. Using a 36-mm socket, unscrew cap and filter and allow the coolant to drain
into the housing. After draining, remove the assembly from the housing.
4. Remove the filter from the plastic cap by placing the filter on a solid surface
and apply pressure on the plastic cap at an angle.
5. Remove coolant filter O-ring and discard it. Lightly lubricate a new O-ring
with clean engine oil and install it on the filter cap.
6. Check filter housing for any debris and remove if necessary.
7. Insert a new filter element into the cap.
8. Insert element and cap assembly into the housing. Torque the cap to 55-60
Nm (41-44 lbft).
9. Check coolant level and adjust if necessary.
wheels are blocked.
10. Start engine with the accelerator pedal in the idle position. Monitor all
gauges or indicator lamps.
11. Check the filter housings for signs of leakage.
Checking the Hoses

Check the hoses as follows:
178
1. Inspect the cooling system hoses and replace any hose that shows obvious
signs of damage or feels abnormally soft or hard.
2. Replace damaged clamps.
3. Correct all external leaks as soon as detected.
NOTE: If Detroit Genuine antifreeze/coolant (or equivalent fully formulated,
pre-charged antifreeze is used, a pre-charged element is not required.
4. Check coolant inhibitor levels at the intervals listed in this manual.
Refer to section "EPA10/GHG14 DD Series Preventive Maintenance
Tables"
How to Service the Dry Type Air Cleaner

Maintain the air cleaner as follows:
1. Replace dry type air cleaner elements when the maximum allowable air
cleaner restriction [20 in. H2O (5.0 kPa)] has been reached. Some air
cleaners are equipped with a restriction indicator which aids in determining
the servicing interval.
2. Do not clean and/or reuse dry paper-type air cleaner elements unless the
cleaning method used removes clogging without damaging the element.
3. Inspect and clean the elements in accordance with the air cleaner
manufacturer's recommendations, if any.
179
Engine Storage
Engine Storage
When an engine is to be stored or removed from operation for a period of time,
special precautions should be taken to protect the interior and exterior of the
engine, transmission and other parts from rust accumulation and corrosion. The
parts requiring attention and the recommended preparations are given below.
Preparing Engine for Storage

It will be necessary to remove all rust or corrosion completely from any exposed
part before applying rust preventive compound. Therefore, it is recommended that
the engine be processed for storage as soon as possible after removal from
operation.
The engine should be stored in a building that is dry and can be heated during the
winter months. Moisture-absorbing chemicals are available commercially for use
when excessive dampness prevails in the storage area.
Temporary Storage (30 Days or Less)

An engine prepared in this manner can be returned to service in a short time by
removing the seals at the engine openings and by checking the engine coolant, fuel
oil, lubricating oil and transmission oil levels.
To protect the engine for a temporary period of time (30 days or less), follow this
procedure:
1. With the engine at ambient temperature and cool to the touch, drain engine
crankcase oil into a suitable container. Dispose of the oil in an
environmentally friendly manner, according to state and/or federal (EPA)
recommendations.
2. Fill the crankcase to the proper level with the recommended viscosity and
grade of oil.
3. Fill the fuel tank with the recommended grade of fuel oil. Operate the engine
for two (2) minutes at 1200 rpm and no load. Do not drain the fuel system or
the crankcase after this run.
4. Check the air cleaner and service it, if necessary.
NOTE: If an antifreeze solution is not required during storage, flush the
cooling system with a good soluble oil (3% 5% by volume) rust inhibitor to
prevent rusting of the outside diameter of the cylinder liners.
5. If freezing weather is expected during the storage period, check the
antifreeze/coolant for required freeze and inhibitor protection. Add
antifreeze solution to the cooling system in accordance with Detroit's
recommendations. Refer to section "How to Select Coolant"
180
WARNING: EYE INJURY

6. Clean the exterior of the engine (except electrical parts) with fuel oil and
dry with compressed air.
7. Seal all engine openings. The material used must be waterproof, vaporproof and possess sufficient physical strength to resist puncture and damage
from the expansion of entrapped air.
Extended Storage (More than 30 Days)

Outdoor storage of the engine is not recommended. If units must be kept out of
doors, follow the preparation and storage instructions already given. Protect units
with quality, weather-resistant tarpaulins (or other suitable covers) arranged to
provide for air circulation.
NOTICE: Do not use plastic sheeting for outdoor storage. Enough moisture
can condense on the inside of the plastic to rust ferrous metal surfaces and
pit aluminum surfaces. If a unit is stored outside for any extended period of
time, severe corrosion damage can result.
NOTE: Plastic is fine for indoor storage.
The stored engine should be inspected periodically. If there are any indications of
rust or corrosion, corrective steps must be taken to prevent damage to the engine
parts. Perform a complete inspection at the end of one year and apply additional
treatment as required.
To prepare an engine for extended storage (more than 30 days), follow this
procedure:
1. Drain the cooling system. Refer to section "Cooling System Drain
Procedure", and flush with clean, soft water. Refill with clean, soft water and
add a rust inhibitor to the cooling system.
2. Circulate the coolant by operating the engine until normal operating
temperature is reached. Refer to section "Cooling System Fill Procedure".
3. Stop the engine.
4. With the engine at ambient temperature and cool to the touch, drain the
engine crankcase oil into a suitable container. Remove the oil filters. Dispose
of the oil and filters in an environmentally friendly manner, according to
state and/or federal (EPA) recommendations. Replace the drain plug and
torque to 45-50 Nm (33-77 lbft).
181
Engine Storage
5. Install new lubricating oil filters. Fill the crankcase to the proper level with
Tectyl 930A preservative lubricating oil or an equivalent 30-weight
preservative lubricating oil meeting Mil-L-21260C, Grade 2 Specification.
NOTE: If engines are stored where condensation of water in the fuel tank
may be a problem, additives containing methyl carbitol or butyl cellusolve
may be added to the fuel. Follow manufacturer's instructions for treatment.
Where biological contamination of fuel may be a problem, add a biocide
such as Biobor JF (or equivalent) to the fuel. When using a biocide, follow
the manufacturer's concentration recommendations and observe all
cautions and warnings.
6. Drain the fuel tank. Refill with enough clean No. 1 diesel fuel to permit the
engine to operate for about ten (10) minutes. If draining the fuel tank is not
convenient, use a separate, portable supply of recommended fuel.
7. Drain the fuel system and remove the fuel filters. Dispose of used filters in
an environmentally responsible manner, according to state and/or federal
(EPA) recommendations. Fill the new filters with No. 1 diesel fuel or pure
kerosene and install on the engine.
8. Operate the engine for five (5) minutes to circulate the clean fuel throughout
the engine. Be sure the engine fuel system is full.
9. Stop the engine and allow to cool. Then disconnect the fuel return line and
the inlet line at the primary filter and securely plug both to retain the fuel in
the engine.
10. Transmission: Follow the manufacturer's recommendations for prolonged
storage.
11. Power Take-Off: If equipped, follow manufacturer's recommendations for
prolonged storage.
NOTE: Failure to properly seal off the turbocharger air inlet and exhaust
outlet openings before engine storage may permit air drafts to circulate
through the turbocharger and rotate the turbine/compressor shaft without an
adequate flow of lubricating oil to the center housing bearings resulting in
severe bearing damage.
12. Turbocharger: Since turbocharger bearings are pressure lubricated through
the external oil line leading from the oil filter adaptor while the engine is
operating, no further attention is required. However, the turbocharger air
inlet and turbine exhaust outlet connection should be sealed off with
moisture-resistant tape.
NOTE: Do not apply oil, grease or any wax-base compound to the flywheel.
The cast iron will absorb these substances, which can sweat out during
operation and cause the clutch to slip.
182
13. Apply a non-friction rust preventive compound to all exposed engine parts.
If convenient, apply the rust preventive compound to the engine flywheel. If
not, disengage the clutch mechanism to prevent the clutch disc from
sticking to the flywheel.
14. Drain the engine cooling system. If the engine will be exposed to freezing
temperatures, install genuine Detroit Power Cool antifreeze or an equivalent
ethylene glycol-base or propylene glycol-base antifreeze solution that
provides the required freeze, boil over and inhibitor protection. Refer to
section "Coolant Requirements"
15. Drain the preservative oil from the engine crankcase. Reinstall and torque
the 3/4" 14 square, magnetic drain plug to 45-50 Nm (33-77 lbft).
16. Remove and clean the battery and battery cables with a baking soda-water
solution and rinse with fresh water. Do not allow the soda solution to enter
the battery. Add distilled water to the electrolyte (if necessary) and fully
charge the battery. Store the battery in a cool (never below 0 C or 32 F)
dry place. Keep the battery fully charged and check the level and specific
gravity of the electrolyte regularly.
17. Insert heavy paper strips between the pulleys and drive belts to prevent
sticking.
18. Seal all engine openings, including the exhaust outlet, with moistureresistant tape. Use cardboard, plywood or metal covers where practical.
19. Clean and dry the exterior painted surfaces of the engine and spray with a
suitable liquid automobile body wax, a synthetic resin varnish, or a rust
preventive compound.
20. Protect the engine with a good weather-resistant tarpaulin and store it under
cover, preferably in a dry building which can be heated during the winter
months.
Procedure for Restoring to Service an Engine that Has

Been in Extended Storage
If an engine has been in extended storage, prepare it for service as follows:
1. Remove the covers and tape from all the openings of the engine, fuel tank
and electrical equipment. Do not overlook the exhaust outlet.
2. Remove the plugs from the inlet and outlet fuel lines and reconnect the lines
to their proper positions.
3. Wash the exterior of the engine with fuel oil to remove the rust preventive.
Do not wash electrical components.
4. Remove the rust preventive from the flywheel. Flush any soluble oil rust
inhibitor (if used) in the cooling system.
5. Remove the paper strips from between the pulleys and drive belts.
6. Fill the crankcase to the proper level with the required grade of lubricating
oil. Use a pressure lubricator to insure all bearings and rocker shafts are
lubricated.
183
Engine Storage
7. Fill the fuel tank with the required fuel.

8. Close all drain cocks and fill the engine cooling system with clean, soft water
and required inhibitors. If the engine is to be exposed to freezing
temperatures, install genuine Detroit Power Cool antifreeze or an equivalent
ethylene glycol-base or propylene glycol-base antifreeze solution which
provides required freeze, boil over, and inhibitor protection. Refer to section
"How to Select Coolant"
9. Install and connect the battery. Make sure the average specific gravity of the
battery is 1.260 or higher. Charge the battery, if necessary.
10. Service the air cleaner, if required.
11. Transmission: Follow the manufacturer's recommendations covering the
return of the transmission to service.
12. Power Take-Off: If equipped, follow the manufacturer's recommendations
covering the return of the power take-off to service.
13. Turbocharger: Remove the covers from the turbocharger air inlet and turbine
outlet connections. Reconnect piping as required. Pre-lube the turbocharger
center bearing housing. Refer to section "Lubrication System Checks"
14. Fill the cooling system. Refer to section "Cooling System Fill Procedure"
15. After all preparations are completed, start the engine.
NOTE: The small amount of rust preventive which remains in the fuel
system will cause smoky exhaust for a few minutes.
NOTE: Before subjecting the engine to a load or high speed, allow it to
reach normal operating temperature.
16. Check for trouble codes.
a. If there are no codes, perform a parked regeneration.
b. If there are codes, repair what is necessary then perform a parked
regeneration.
184
Customer Assistance
Using Road Service in the U.S. or Canada

The satisfaction and goodwill of the owners of Detroit engines are of primary
concern to Detroit and its distributor/dealer organizations. Contact the Customer
Support Center at 1-800-445-1980.
If you require road service for any reason in the U.S. or Canada, you may call the
1-800-445-1980 customer assistance phone number. An operator will assist you in
determining what type of service is required. Not all problems are engine related
and not all problems are covered by engine or vehicle warranties. YOU MAY BE
RESPONSIBLE FOR REPAIR EXPENSES.
Before calling Customer Assistance, please do the following:
Check the coolant level.

Check the fuel level.
Check the DDEC fuses.
Check for fuel leaks.
Make sure manual shutoff valve (if installed) on the fuel filter adaptor or fuel
supply line is open.
Check the oil level on the dipstick.
Check the diagnostic codes.
If you call, have the following information available:
Engine serial number

Vehicle make, model, and VIN
Odometer mileage (kilometers) or hour meter hours
Vehicle owner/company name
Availability of Detroit Service Outlets

As the owner of a Detroit product, you have a complete network of Detroit
service outlets in the U.S. and Canada, plus many outlets worldwide that are
prepared to meet your parts and service needs:
Service by trained personnel

Sales team to help determine your specific power requirements
In many areas, emergency service 24 hours a day
Complete parts support
Product information and literature
We recognize however, that despite the best intentions of everyone concerned,

misunderstandings may occur. Normally, any situation that arises in connection
with the sale, operation or service of your product will be handled by the authorized
185
Customer Assistance
service outlet in your area (in the U.S. and Canada, check the Yellow Pages or the
service locator at www.demanddetroit.com for Detroit service outlet nearest
you).
186
Detroit Genuine Coolant Engine Products

Maintenance of the cooling system requires the chemical makeup of the system to
be balanced.
Detroit Genuine Fully Formulated Inhibited Ethylene Glycol Coolants
The part numbers and sizes of concentrated and pre-blended 50:50 Detroit Genuine
Coolants are listed in the following Tables.
Table 38.
Detroit Genuine Fully Formulated Inhibited Ethylene Glycol Coolants
Coolant Type
Concentrated
Pre-blended 50:50
Part Number
Description
23512138
One Gallon Jug 6 Per Case
23512139
55 Gallon Drum
23529295
330 Gallon Tote
23512140
Bulk Delivery 1,000 Gallon Min.
23528203
One Gallon Jug 6 Per Case
23518918
55 Gallon Drum
23528544
330 Gallon Tote
23513503
Bulk Delivery 1,000 Gallon Min.
Detroit Genuine Supplemental Coolant Additive Need Release Filters

Detroit Genuine Supplemental Coolant Additive Need Release Filters are shown
below.
Table 39.
Detroit Genuine Supplemental Coolant Additive Need Release Filters
Coolant Type
Part Number
Description
Detroit Genuine Inhibited

Ethylene Glycol Coolant
NF2091
For 0 8 Gallon Systems
23516489
For 8 20 Gallon Systems
Detroit Genuine Cooling System Cleaners

Detroit Genuine Cooling System Cleaners are shown below.
187
Detroit Genuine Coolant Engine Products
Table 40.
Detroit Genuine Cooling System Cleaners
Coolant Type
Part Number
Description
200164
One-Half Gallon Jug 6 Per Case
200105
5 Gallon Pail
200155
55 Gallon Drum
201549
Twin Pack 2 Per Case
On-Line Cleaner
Twin Pack
Detroit Genuine Fluid Analysis Products

Detroit Genuine Fluid Analysis Products are shown below.
Table 41.
Detroit Genuine Fluid Testing
and Analysis Products
Application
Part Number
Description
Indicates Nitrite, Molybdate &

Glycol Levels
23519401
3-Way Coolant Test Strips

(Single Foil Packs)

Glycol Levels
23519402
3-Way Coolant Test Strips (Bottle

of 50)

Glycol Levels
23522774
3-Way Coolant Test Strips (Bottle

of 10)
Complete Inhibited Ethylene

Glycol Coolant Analysis
23516921
Coolant Analysis Bottle (Carton

of 6)
Organic Coolant Analysis
23539088
Laboratory Coolant Analysis
188
Engine Oil Capacities

Consult with a Detroit distributor to obtain the proper engine oil filters.
The engine oil capacities for the DD Platform Engine On-Highway Vehicle
application are listed in the following tables. Contact your local Detroit service
center if you need more specific information.
NOTE: There are approximately 5.0 L (5.2 qts) of oil represented from the
fill mark to the full mark.
NOTICE: Overfilling the oil pan can cause engine damage.
Table 42.
Truck - EPA07/
EPA10/GHG14
DD13
DD15
DD16
Total Dry Engine Oil

Volume
44.0 L (46.5 qt)
49.0 L (51.8 qt)
49.0 L (51.8 qt)
Oil and Filter Change
38.0 L (40.1 qt)
43.0 L (45.4 qt)
43.0 L (45.4 qt)
Remaining in Engine
after Oil Drain
(Includes Filter
Removal)
6.0 L (6.3 qt)
6.0 L (6.3 qt)
6.0 L (6.3 qt)
Dip Stick Min. to

Max. Range
5.0 L (5.2 qt)
5.0 L (5.2 qt)
5.0 L (5.2 qt)
Sump Oil Volume
35.0 L (37.0 qt)
40.0 L (42.3 qt)
40.0 L (42.3 qt)
Table 43.
Coach
EPA10 DD13
GHG14 DD13
Total Dry Engine Oil

Volume
51.0 L (53.8 qt)
47.0 L (49.7 qt)
Oil and Filter Change
45.0 L (47.6 qt)
40.0 L (42.3 qt)
Remaining in Engine
after Oil Drain
(Includes Filter
Removal)
6.0 L (6.3 qt)
6.0 L (6.3 qt)
Dip Stick Min. to

Max. Range
5.0 L (5.2 qt)
5.0 L (5.2 qt)
Sump Oil Volume
42.0 L (44.4 qt)
37.0 L (39.1 qt)
189
Table 44.
Engine Oil Capacities - GHG17 Only
Parameter
DD13 Truck
DD13 Coach
DD15 Truck
DD16 Truck
Service Fill (Oil

and Filter
Change)
38.0 L (40.0 qt)
45.0 L (48.0 qt)
43.0 L (45.0 qt)
43.0 L (45.0 qt)
Oil Pan
Capacity, High
Limit
35.0 L (37.0 qt)
42.0 L (44.0 qt)
40.0 L (42.0 qt)
40.0 L (42.0 qt)
Oil Pan
Capacity, Low
Limit
30.0 L (32.0 qt)
37.0 L (39.0 qt)
35.0 L (37.0 qt)
35.0 L (37.0 qt)
190

Manual de SCR dd15

Uploaded by

Copyright:

Available Formats

Manual de SCR dd15

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual de SCR dd15

Uploaded by

Copyright:

Available Formats

DDC-SVC-MAN-0189

DD Platform Operators Manual

Specifications are subject to change without notice. Detroit Diesel

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

Performing a Parked Regeneration - EPA07............................................... 92

DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION

Engine Out of Fuel How to Restart........................................................ 158

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

California Proposition 65 Warning and Engine Idle

All information subject to change without notice.

DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION

Non-Genuine and Rebuilt Component Quality Alert

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

Engine Conversions and Modifications

All information subject to change without notice.

DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

All information subject to change without notice.

DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

WARNING: PERSONAL INJURY

All information subject to change without notice.

DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

All information subject to change without notice.

DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION

Flush your skin with water.

WARNING: PERSONAL INJURY

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

WARNING: PERSONAL INJURY

All information subject to change without notice.

DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

Single-stage Air Compressor

Figure 1. DD13 Left Side View

DDC-SVC-MAN-0189Copyright 2015 DETROIT DIESEL CORPORATION

Figure 2. DD13 Right Side View

All information subject to change without notice.

Copyright 2015 DETROIT DIESEL CORPORATIONDDC-SVC-MAN-0189

DD Platform Operators Manual

Single Cylinder Air Compressor

Figure 3. DD15 TC Left Side View

All information subject to change without notice.