Scribd
Upload
732 views2 pages

Gtir Sr20det

The document provides specifications for a SR20DET engine, including: - It is a 1998cc turbocharged inline 4-cylinder engine that produces 230PS at 6400rpm and 27.2kgm of torque at 4800rpm. - Service checks include spark plug gap of 0.9mm and valve clearances of 0.30mm cold and 0.35mm hot. - Tuning parameters include ignition timing of 20 degrees BTDC at 850rpm and idle speed of 900±50rpm.

Uploaded by

joe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
732 views2 pages

Gtir Sr20det

The document provides specifications for a SR20DET engine, including: - It is a 1998cc turbocharged inline 4-cylinder engine that produces 230PS at 6400rpm and 27.2kgm of torque at 4800rpm. - Service checks include spark plug gap of 0.9mm and valve clearances of 0.30mm cold and 0.35mm hot. - Tuning parameters include ignition timing of 20 degrees BTDC at 850rpm and idle speed of 900±50rpm.

Uploaded by

joe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

GTiR SR20DET Specifications (c) copyright antrx.

com 2004

Mechanical features
Engine model
Engine type
DOCH, 16 valves with intercooler
Displacement
Max power output
Max torque
Bore & stroke
Compression ratio
Control system
Transmission type
Transmission

Final gear ratio

SR20DET
Turbocharged, in line 4
1998 cc
230/6400 PS/rpm
27.2/4800 kgm/rpm
86 x 86 mm
8.3
Electronic port injection
5-speed manual
1st 3.285 2nd 1.850
3rd 1.272 4th 0.954
5th 0.740 Rev 3.266
4.125

Service checks and adjustments


Spark plugs make
Electrode gap
Valve clearance inlet
Exhaust
Compression pressure
Oil pressure

NGK type PFR7B-9


0.9 mm
0.30 mm COLD 0.35 mm HOT
0.30 mm COLD 0.35 mm HOT
9.32 - 11.28 bar
3.4 - 4.4 / 3200 bar/rpm

Tuning and emissions


Ignition coil supply voltage
Primary resistance
Secondary resistance
Firing order
Ignition timing BTDC Deg/rpm
Ignition advace checks
Idle engine speed
Oil temp for CO test
CO content at idle
CO2/O2 content ad idle
HC content at idle
Increased idle speed for CO test
CO content at increased idle speed
Lambda at increased speed

Fuel system

12.0 Volt
1.0 ohms
10000 ohms
1-3-4-2
20 +/- 2 / 850
ECM controlled
900+/-50 rpm
85 C
Tail pipe 0.5 % max
14.5-16 % / 0.1-0.5 %
100 ppm
2800 - 3200 rpm
0.3 %
0.98-1.02

System fuel pressure without vacuum


Injector reistance
Fuel tank capacity

2.94 bar
1 - 3 ohm
50 litres

Lubricants and capacities


Engine oil grade SAE
Engine with filter
Gearbox oil grade SAE
5 speed gearbox capacity
Transfer box capacity
Diffrential oil grade SAE
Front/rear capacity

10W/30
3.4 litres
80W/90
4.2 litres
1.5 litres
90W
1.0/1.0 litres

Coolant system
Coolant capacity
Coolant temperatur sensor 300 - 330 ohm/80 C
Suggested anti-freeze percentage

5.7 litre
-15 C 30%
-30 C 50%

Air conditioning
Refrigerant type
Quantity
Oil type
Quantity

R12
650 - 750 grams
Suniso 5GS
200 cm3

Tightening torques
Spark plug
Front hub
Rear hub
Steering track rod end
Brake caliper to carrier front/rear
Brake caliper carrier to hub front
Road wheels

20-29 NM
196-275
196-275
29-39 NM
59 NM / 27 NM
59 NM
98 - 118 nM

Brake disc dimensions/tolerance


Brake disc diameter
Minimum disc thickness
Brake fluid (minimum spec,)

Front 260 mm
Rear 230 mm
Front 24 mm
Rear 8 mm
Dot 3

Turbo charging system


Turbo type
Carret code
Compressor wheel diameter/trim
Turbine wheel diameter/trim
A/R housing
Garret part no.
Engine cut switch operational pressure

T28
T28
60 mm / 60
53 mm /79
0.86 inches
465997 - 0004
1.4 bar

You might also like