Scribd
Upload
141 views4 pages

Z Section Properties

This document contains design calculations for side runners (girts) of a structure under major axis loads and minor axis loads. It calculates the required bending moment for the girts based on factors like yield stress, wind pressure, spacing of loads. It then checks if the required bending moment is less than the design bending moment to ensure pass criteria is met for the girt design. Key parameters calculated include factored loads, bending moments, load combination ratios and section properties. The design is checked for several load combinations and criteria and found to pass in all cases.

Uploaded by

vijaystructural
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
141 views4 pages

Z Section Properties

This document contains design calculations for side runners (girts) of a structure under major axis loads and minor axis loads. It calculates the required bending moment for the girts based on factors like yield stress, wind pressure, spacing of loads. It then checks if the required bending moment is less than the design bending moment to ensure pass criteria is met for the girt design. Key parameters calculated include factored loads, bending moments, load combination ratios and section properties. The design is checked for several load combinations and criteria and found to pass in all cases.

Uploaded by

vijaystructural
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 4

DESIGN CALCULATIONS FOR GIRT (SIDE RUNNERS)

ONLY FOR MAJOR AXIS LOADS


YIELD STRESS OF GIRT
R UNSTIFFENED COMPRESSION FLANGE b

SPAN FOR
VERTICAL
BENDING
M
9.5

WIND
PRESSURE
KN/M^2
0.78

=
=

235
0.9

N/MM^2

SPACING OF WIND LOAD FACTORED LOADS REQ BENDING


GIRT
ON GIRT
FACTOR = 1
MOMENT
M
1.265

KN/M
0.9867

KN/M
0.9867

KN-M
11.131209375

SECT MODULAS
MAJOR AXIS
Zxx
CM^3
78.95

0.9

DESIGN RATIO
PASS
MOMENT
REQ BEND MOMENT<
DESIGN MOMENT
KN-M
16.69793 0.67
PASS

DESIGN CALCULATIONS FOR GIRT (SIDE RUNNERS)


FOR MINOR AXIS LOADS AND COMBINATION
WEIGHT OF SHEET

16.5

Horizontal SPACING SPAN FOR


OF
VERTICAL
SAG RODS
BENDING
M
M
3
3.17

KG/M

SELF WEIGHT
OF GIRT
KG/M
8.38

TOTAL DEAD LOAD REQ BENDING


MOMENT
KG/M
24.88

SECT MODULAS
MINOR AXIS

KN-M
0.31

CM^3
14.5

COMBINATON LOAD CHECKS


FACTORED LOADS
1.4XD
1.2XD
1.3XW
0.9XD

0.43
0.37
14.47
0.28

FACTORED REQUIRED MOMENTS


1.4XD
1.2XD
1.3XW
0.9XD

0.14
0.12
0.87
0.09

LOAD COMBINATION RATIOS


.
1.4XD
1.2D+1.3W
0.9D-1.3W

0.14
0.99
-0.78

PASS
PASS
PASS

0.9

DESIGN
MOMENT
KN-M
3.07

RATIO

0.10

PASS
REQ BEN MOMENT<
DESIGN MOMENT
PASS

DATAS:
HEIGHT
WIDTH
BENT LENGTH
SHEET THICK
ANGLE

cm

mm

h
b
a
t

34.2

342

0.0342

10

100

0.01

40

0.004

0.8

0.0008

20.183

49.76

PROPERTIES:
AREA

MOMENT-XX
Ix1
MOMENT-YY
Iy1
POLAR MOMENT Ix1y1
SEC. MODULAS
SEC. MODULAS

Zxx
Zyy

tg2
Ix
Iy
It

CM^2

8813.137 CM^4

1173.333 CM^4

2334.4

CM^4

515.3881 CM^3

117.3333 CM^3

-0.611115

6393.308 CM^4

3593.162 CM^4

10.61547

You might also like