0% found this document useful (0 votes)
568 views16 pagesJPSC Assistant Engineer Civil Engineering Previous Papers PDF
Uploaded by
abhiCopyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
0% found this document useful (0 votes)
568 views16 pagesJPSC Assistant Engineer Civil Engineering Previous Papers PDF
Uploaded by
abhiCopyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
/ 16
=
Berial Nos QUESTION BOOKLET [Al
51205
CIVIL ENGINEERING (05)
Time Allowed : 3 Hours Maximum Marks : 200
[1 Hour for Objective [100 Marks for Objective
2 Hours for Subjective | 100 Marks for Subjective |
INSTRUCTIONS FOR CANDIDATES
1. This Question Booklet consists of two Parts (Objective and Subjective).
Candidate has to attempt both the Parts.
2. In Objective Part, there are 50 questions carrying 2 marks each. There is
no negative marking for any wrong answer. In Subjective Part, four (4)
questions should be answered in which Question No. 1 is compulsory.
2
Please do not open this Question Booklet until you are told to do so.
4. Candidate must fill up the necessary information in the space provided on the
OMR Answer Sheet before commencement of the test.
S. For marking the correct answer, darken one circle by black or blue ball-point
pen only. Please do not mark on more than one circle. Darkening on more
than one circle against an answer will be treated as wrong answer.
6. Do not detach any leaf from this Question Booklet. After the examination,
hand over the OMR Answer Sheet to the Room Invigilator.
7. Possession and use of Calculator, Mobile Phone and Pager is prohibited in the
Examination Hall,
8. Candidates are informed that evaluation of OMR Sheets will be done by
Electronic Machine. So, they should shadow the bubbles of Roll No., Booklet
Series and Booklet No. properly, otherwise Machine will not be able to
evatuate it. Failure to comply this instruction will be sole responsibility of the
candidates.
met PART—A
( Objective )
1, Maximum strain at the level of
compression steel for a doubly
reinforced rectangular section
having effective depth , effective
cover to compression steel as d
and neutral axis depth from
compression face as x, will be
{A) 0-0035
ad
@) 0-00355—
© o-0095{1~-£°
x,
(D) 0-002
2, The main reinforcement in an RC
slab consists of 10mm bars
@ 100mm spacing center to
center. If it is desired to replace
the 10 mm bars by 12 mm bars,
then the spacing of the 12mm
bars will be
(A) 100 mm
(8) 120 mm
(C) 144 mm
(D) 240 mm
19 (Cpa
3. A steel hook of 10 mm diameter
is embedded in concrete for a
distance 70 mm. If permissible
stress in steel is 343 N/mm?
and the bond stress is not to
exceed 0°7N/mm?, then the
maximum load that can be
suspended on the hook is
(A) SSN
(B) 1540 N
(C) 26950 N
(py):74300 N
4. A short square column with side
200 mm is subjected to a design
load of 300KN. If the grade
of concrete is M-20 and the grade
of steel is Fe-415, then the area
of longitudinal steel required for
the section in the limit state
design will be
(ao
(8) 320 mm?
{C) 300 mm?
(D) 160 mm?
i
\
\
| 5. If fx is the characteristic
strength of concrete, then as per
IS 456:2000, the modulus of
elasticity of concrete in N/mm?
will be
(A) S700 /Fax
(B) 5000/7,
(C) 5700fux
(D) 5000f.5,
6. In the limit state design method,
the material safety factors for
steel and concrete are taken as
(A) 1-5 for both steel and
concrete
{B) 1:15 for both steel and
concrete
(C) 1-15 for steel and 1-5 for
concrete
(D) 1-5 for steel and 1-15 for
concrete
7. For M-30 grade concrete, the 28
days characteristic compressive
strength will be
(A) 30 KN/m?
{B) 30 N/m?
{C) 30 N/cm?
(D) 30 N/mm?
19 (C)-A
10.
For the fillet weld cross-section
shown in the figure below, the
throat thickness is
c
D,
4 B
(a) AB
(B) BC
(€) ac
(©) BD
The effective length of the fillet
weld is taken as
(A) total length-2x throat size
(B) total length~2xweld size
(C) total length-V2xweld size
(D) 0-7xtotal size
‘Two steel plate each 300 mm
wide and 10mm thick are
connected by single bolt. If the
plates are in tension and
diameter of bolt hole is 20 mm,
the net section aréa of the plate
will be
(A) 2686 mm?
(B) 2780 mm?
(C) 2800 mm?
{D) 3000 mm?
{PTo. 11, For the
12.
eccentric _ bolted
connection of bracket shown in
figure, which bolt will have the
maximum resultant force?
ww
P
oD{ Ao}
°B| Bo!
oF | Cot
Lwp—
(A) Bolt A
(B) Bolt B
(C) Bolt D
(D) Bott £
Intermediate vertical stiffeners
are provided in plate girders to
(A) eliminate the web buckling
(B) eliminate the local buckling
(C) transfer the vertical loads
{D) prevent the
deflection
excessive
19 (Cra
13.
14.
15.
In the built-up compressions
members, the number of battens
should be such that the member
is divided into not less than
(A) two ways
(B) three ways
(C) four ways
(D) six ways
Loads on a connection is not
eccentric for
(A) lap joint
(B) single-cover butt joint
(C) double-cover butt joint
(D) any of the joints mentioned
above
In case of laterally unrestrained
beams
(A) the compression
deflects laterally
flange
(B) the tension flange deflects
laterally
{C) the web deflects laterally
(©) None of the above
\ 16. In a simply supported pre-
17.
stressed concrete beam
subjected © to uniformly
distributed load on entire span,
the ideal shape of the cable
profile will be
(A) concentric with the center of
cross-section
(B) at constant eccentricity over
the entire span
(C) varying linearly with zero
eccentricity at ends and
maximum eccentricity at
mid-span
(D) parabolic with =—zero
eccentricity at ends and
maximum eccentricity at
mid-span
Point of contraflexure occurs in a
structure when
(A) bending moment is zero
(B) bending moment changes
sign
(C) shear force is zero
(D) All of the above
19 (Cra
18.
For the truss shown in the figure
below, the number of zero-force
members will be
at
®) 2
3
m4
For the simply supported beam
of span L, the shape of the shear
force diagram will be rectangle of
length L if the beam is subjected
to
(A) a point load at mid-span
8) uniformly distributed load
over the full-span
(C) a clockwise moment at any
point within. the span
(D) equal magnitude hogging
moments at supports
[PT0. 21.
22.
For the frame shown in the
figure below, the degree of static
indeterminacy is
(a) 6
(B) 9
(C) 12
(D) 15
Ifa framed structure is statically
indeterminate to the second
degree, then the minimum
number of plastic _ hinges
required for the complete
collapse of the structure will be
@ 1 2
(©) 3 4
Which of the following represents
the increasing order of shape
factor?
(A) Rectangle, I-section, solid-
circular section, diamond
(B) I-section, rectangle, solid-
circular section, diamond
(C) Diamond, —_solid-circular
section, rectangle, I-section
(D) Diamond, __ solid-circular
section, I-section, rectangle
19 (C/A
23. A point load of 50 kN acting at
mid-span of a simply supported
beam produces the same
maximum deflection in the beam
as caused by a uniformly
distributed load of 20 kN/m over
the whole span, The span of the
beam is
(a) 10m
@) 8m
(©) 6m
(0) 4m
- A beam of length 10 m, carrying
a uniformly distributed load of
10 KN/m over the entire length,
rests on two simple supports
symmetrically. In order to have
maximum sagging _ bending
moment developed in the beam
least possible, the distance
between the supports must be
(A) 207m
®) 414m
(©) 5-86m
(0) 7:93m 7 28, A three-hinged parabolic arch of
span 16m and rise 4m is
subjected to a vertical downward
concentrated load of 80 at
quarter span. The horizontal
reaction at A will be
80 kN-m
c
4m-4m 8m
(A) 20 kN
{B) 30 kN
(C) 40 kN
(D) 50 kw.
26. Influence line for redundant
structures can be obtained by
(A) Castigliano’s theorem
(8) Muller-Breslau principle
(C) Unit load method
(0) Maxwell-Betti
theorem
reciprocal
19 (CA
27. A simply supported beam is
loaded as shown in the figure
below. The bending moment at C
will be
20kNm 20KN 40KN 20 KN 29 km
a By cy Dy
eS rosra
Im im im” Im
(A) 20 kN-m (hogging)
(B) 80 kN-m (sagging)
(C) 60 KN-m (sagging)
(D) 40 kN-m (sagging)
28, A beam simply supported at both
ends of length L carries two
equal unlike couples M at two
ends, If the flexural rigidity is
EI = constant, then the central
deflection will be
ML?
) Ger
ML?
©) “eer
ML?
© Fear
ML?
©) Geer
[P70. 29. The given figure shows frame
with a single-concentrated
load P. The fixed end moment
developed at joint A will be
PL PL
w = at
PL PL
om o>
» What is the horizontal
displacement at free end C of the
frame shown in the given figure?
El) |b
A
ML? QML?
aS 68 a
ML? ML?
Og ©) oer
ID (ChA
31. The maximum bending moment
at the left quarter point of a
simply supported beam due to
crossing of UDL of length shorter
than span in the direction left to
right, would occur when the load
has just crossed the section by
(A) one-fourth of its span
(B) half of its span
(C) three-fourths of its span
(D) its full length
The size of the basic stiffness
matrix for a plane truss member,
in member coordinate system is
(a) 2x2
(B) 3x3
(C) 4x4
(D) 6x6
. The number of simultaneous
equations to be solved in the
slope-deflection method is equal
to the
(A) degree static
indeterminacy
(B) degree of kinematic
indeterminacy
{C) number of joints in the
structure
(D) number of members in the
structure 34,
35.
36.
37.
From among the ranges of
numerical values given, select
the range valid for the void ratio
6, as a ratio
(a) eso
(8) O
