VT Test Prosedure

Contractor
Owner
Main Subcontractor
PROJECT NAME: Khabat Thermal Power Plant Units 1&2

OWNER: Ministry of Electricity of Kurdistan Regional Goverment
CONTRACTOR: POSCO Engineering & Construction Co. Ltd.
MAIN SUBCONTRACTOR: GAMA Power Systems Engineering &
Contracting Inc.
PROJE REFERENCE NO:
Re
v
0
Revision
Date
15.09.201
5
Description
For Review
Revision History
Created by
Checked by
A.E.
AKMAN
Emission
Status
Return
Status
B. GKCE
Vendor doc No.:
Vendor Logo
Approved by
Document Code :
Title, Subtitle
VT
TEST PROCEDURE
Format
A4
Rev. 0
Date
15.09.2015
Lang.
En
Date
15.09.2015
Project No.
Project: Khabat Thermal Power Plant Units 1&2
ISSUE DATE
15/09/2015
ENG. N
VT
TEST PROCEDURE
CLIENT N
REV.
SH/OF
2/7
0
SUMMARY
1.
2.
3.
4.
5.
6.
7.
7.1.
7.2.
8.
9.
10.
11.
PURPOSE OF TESTS
REFERENCE DOCUMENT
SCOPE
TERMINOLOGY
TEST EQUIPMENT UNDER TEST
TEST EQUIPMENT REQUIRED
GENERAL INSPECTION
MECHANICAL CHECKS
ELECTRICAL CHECKS
INSULATION RESISTANCE TEST
POLARITY TEST
TRANSFORMER TURNS RATIO TEST
RECORDING OF INSPECTION AND TEST DATA
3
3
3
3
3
3
4
4
4
4
6
6
7
Project No.
ISSUE DATE
15/09/2015
ENG. N
VT
TEST PROCEDURE
CLIENT N
REV.
1. PURPOSE OF TESTS
Check conformity with specifications. Check for satisfactory condition prior to energizing.
2. REFERENCE DOCUMENT
Electrical drawing N
3. SCOPE
All Voltage Transformers at MV switchyard
4. TERMINOLOGY
No applicable.
5. TEST EQUIPMENT UNDER TEST
The concerned equipments are all types of potential transformers
6. TEST EQUIPMENT REQUIRED
- RS polarity test set
or, if not available, storage battery,
milliammeter, and switch
- Megohmmeter, 500 V - 5 kV
- Ohmmeter
- Multimeter (volts, amperes, ohms, etc...)
- Auto transformer
- Step-up transformer
SH/OF
3/7
0
Project No.
ISSUE DATE
15/09/2015
ENG. N
VT
TEST PROCEDURE
CLIENT N
REV.
SH/OF
4/7
0
7. GENERAL INSPECTION
7.1.
MECHANICAL CHECKS
- General visual inspection and compliance with drawings and manuals
- Check nameplate ratings and HV and LV terminal markings
- Check that all parts of the transformer are properly assembled and tight
- Check the HV connections for looseness, stressed terminals and poor grounding
- Check the cable connections on the LV side and the markings
- Check the oil levels and inspect for leakage (where applicable)
1/ Capacitor divider type
Check that all parts of the transformer are properly assembled and tight
Capacitors together
Capacitors and measuring set
2/ Electromagnetic type
Check the intermediate connections
7.2.
ELECTRICAL CHECKS
- Check the equipment grounding (continuity and connections)
- Check the fuse ratings
- Perform the operation described in the following pages
8. INSULATION RESISTANCE TEST

To obtain values as close as possible to the manufacturers specifications, the insulators must be
very clean.
Select the Megger range corresponding to the ratings of the equipment under test :
LV: 6 to 100 volts (direct current)
MV: 100 to 1000 volts (direct current)
HV: 1000 to 5000 volts (direct current)
Project No.
ISSUE DATE
15/09/2015
ENG. N
VT
TEST PROCEDURE
CLIENT N
REV.
The theoretical values are furnished by the manufacturer.
Measurements between primary and secondary
Measurements between primary and ground
Measurement between secondaries and between secondary and ground
SH/OF
5/7
0
Project No.
ISSUE DATE
15/09/2015
ENG. N
VT
TEST PROCEDURE
CLIENT N
SH/OF
6/7
REV.
9. POLARITY TEST
The polarity is checked using the kick method (application of direct current) and check of
deflection on a bidirectional milliammeter.
This test is also used to check primary and secondary circuit continuity.
- When switch K is closed, the milliammeter pointer deflects upscale.
- When the circuit is opened, the milliammeter pointer deflects in the negative direction.
10. TRANSFORMER TURNS RATIO TEST

A variable AC source is applied on the primary side. The primary and secondary voltages are
measured to determine the ratio V2 / V1.
Project No.
ISSUE DATE
15/09/2015
ENG. N
VT
TEST PROCEDURE
CLIENT N
REV.
SH/OF
7/7
0
CPC 100 Display

11. RECORDING OF INSPECTION AND TEST DATA
The results of the checks and measurements made during the field tests shall be recorded on the
test forms:

VT Test Prosedure

Uploaded by

Copyright:

Available Formats

VT Test Prosedure

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

VT Test Prosedure

Uploaded by

Copyright:

Available Formats

Contractor

PROJECT NAME: Khabat Thermal Power Plant Units 1&2

Vendor doc No.:

Project: Khabat Thermal Power Plant Units 1&2

Project: Khabat Thermal Power Plant Units 1&2

Project: Khabat Thermal Power Plant Units 1&2

Capacitors and measuring set

8. INSULATION RESISTANCE TEST

Project: Khabat Thermal Power Plant Units 1&2

The theoretical values are furnished by the manufacturer.

Measurements between primary and secondary

Measurements between primary and ground

Measurement between secondaries and between secondary and ground

Project: Khabat Thermal Power Plant Units 1&2

10. TRANSFORMER TURNS RATIO TEST

Project: Khabat Thermal Power Plant Units 1&2

CPC 100 Display

You might also like