Jaycar Electronics Tech Update: NETWORKS.

PDF (1)

Networking Basics
Keen to link your computers together in a network? It’s easier and cheaper than ever
to do this, thanks to recent developments in both hardware and software. Here’s a
quick update on modern networking basics — and a practical guide to setting up your
own network.
W H E N E V E R Y O U have more than one computer being 1976, when researchers Dr Robert Metcalfe and Dr
used at the same location, networking them together David Boggs of the Xerox Palo Alto Research Center
makes a lot of sense. Not only can you transfer files (PARC — the same place that developed the GUI or
between them quickly and easily, but they can also share ‘graphical user interface’, the ancestor of Macintosh and
expensive resources like laser printers, hard disc arrays, Windows operating systems) presented details of a
backup tape drives, CD and DVD burners, scanners, ‘Local Computer Networking System’ which allowed
internet connections and so on. data to be transferred between a number of computers
Thanks to recent developments in both hardware and and printers, at what then seemed a high speed:
software it’s now also easier than ever to hook up your 2.94Mb/s (megabits per second). They dubbed the new
own network, and at surprisingly low cost. In this Tech networking system E t h e r n e t , and explained that it
Update we’re going to explain the latest approaches to involved all data being sent in standardised ‘packets’.
cost-effective networking, and give you enough Each packet of data carried its own electronic ‘address’,
understanding to let you tackle setting up your own which allowed the packets to be directed around the
network with confidence and success. network by switching circuits.
First, though, let’s take a quick look at how computer Xerox Corporation was granted a patent for Ethernet
networking developed. (“Multipoint Data Communications System with
Collision Detection”, US Patent No.4063220) on
Networking history December 13, 1977. Then in 1979 Xerox teamed up
with Digital Equipment Corporation and Intel to define
In many ways networking is just another development of the first official standard specification for Ethernet. This
data communications, which began at the same time as Ethernet Version 1.0 was capable of transferring data at
computers themselves. For example in 1940 when 10Mb/s over fairly thick (10mm diameter) 50Ω coaxial
George Stibitz and Samuel Williams, researchers at cable, and became known as ‘thick Ethernet’ or
AT&T’s Bell Laboratories, developed their Complex ‘10Base5’. The second term was because it allowed a
Number Generator — one of the earliest digital 10Mb/s data rate, it used b a s e band transmission rather
computers — they made it possible for users to operate than a modulated high-frequency carrier, and would give
the computer remotely from teletype machines on three reliable data communication over cable lengths up to
different floors in their Manhattan building. They also 500 metres.
developed a system to allow users to communicate with
the machine even more remotely, via telex machines. Four years later, the 802.3 working group of the IEEE
(Institution of Electrical and Electronics Engineers)
Then in 1964, when computers were still very much in released its first industry standard for Ethernet, giving it
the ‘mainframe’ era, Drs John Kemeny and Tom Kurtz of the name IEEE 802.3 Carrier Sense Multiple Access with
Dartmouth College in New Hampshire developed not Collision Detection (CSMA/CD) Access Method and
only the simplified BASIC programming language Physical Layer Specifications . This was essentially a
(Beginners All-purpose Symbolic Instruction Code) but polished-up version of the DEC-Intel-Xerox ‘thick
also a system called t i m e s h a r i n g , which allowed many Ethernet’.
students to use a single computer at what seemed like
the same time, from a large number of teleprinter Later developments of Ethernet came fairly quickly,
terminals spread around the campus and elsewhere. and resulted in Ethernet soon becoming the most
popular computer networking system.
Officially, though, networking is said to have started in

Fig.1: Four computers connected up in a network using the bus or ‘daisy chain’ topology — in this case
using 50-ohm coaxial cable, as used for 10Base5 (thick Ethernet) or 10Base2 (thin Ethernet) networking.
 Jaycar Electronics Tech Update: NETWORKS.PDF (2)

Fig.2: A group of five PCs connected

together in the ‘star’ topology, with a
‘hub’ or multi-port repeater at the centre
of the star. This configuration is most
commonly used in networks using 10BaseT
or 100BaseT Ethernet systems.

In 1985, the IEEE working group came out with ‘thin’ four versions of this are 1000BaseSX, which uses 850nm
Ethernet, also known as ‘cheapernet’ or ‘10Base2’. This lasers and a multi-mode fibre-optic cable; 1000BaseLX,
specified the use of thinner (5mm diameter) 50Ω coaxial which uses a 1300nm laser and either single or multi-
cable, which still allowed 10Mb/s baseband transmission mode fibre-optic cable; 1000BaseCX, which uses
as before, but with a maximum cable length of 185 ‘twinax’ shielded twisted-pair (STP) cable; and
(rounded to ‘200’) metres. 1000BaseT, which uses four pairs of Category 5 UTP
Then in 1990 the IEEE 802.3i or ‘10BaseT’ Ethernet cabling.
standard was released, which opened the door to much Don’t let all of these different ‘flavours’ of Ethernet
cheaper networking because it allowed 10Mb/s worry you, because the two early coaxial-cable based
transmission over the low cost 100Ω u n s h i e l d e d versions (10Base5 and 10Base2) are now regarded as
t w i s t e d - p a i r or ‘UTP’ Category 3 cabling which had by obsolete and are not recommended for new networks.
then become widely used for telephone wiring in Also Gigabit Ethernet is not only fairly expensive, but in
buildings. Using this cable also allowed the network to any case its 1Gb/s performance is essentially ‘overkill’
use a ‘star’ configuration or t o p o l o g y , rather than the for most home and small office applications.
bus or ‘daisy chain’ topology needed for thick and thin That really just leaves 10BaseT and 100BaseT, which
Ethernet (10Base5 and 10Base2). The two different both turn out to be very suitable and cost-effective for
topologies are illustrated in Figs.1 and 2. both home and small office networking. In fact as we’ll
The next big development came in 1995, when the see soon, the price of everything you need for 100BaseT
IEEE working group released the 802.3u standard. This now makes it virtually the ideal system for new net-
became known as ‘100BaseT’ or ‘Fast Ethernet’, because works, even those with only two or three computers.
it allowed 100Mb/s baseband transmission over either Because of this, we’re going to ignore the other vari-
two pairs of Category 5 100Ω UTP cabling (100BaseTX), eties of Ethernet in the rest of this update, apart from
or four pairs of Category 3 cabling (100BaseT4) or two the foregoing mention of their existence.
multi-mode fibre-optic cables (100BaseFX). In other
words, 10 times the speed of 10BaseT.
Then in 1997 came IEEE 802.3x, which defined f u l l USB networking
d u p l e x or simultaneous two-way data communication Before we dive further into Ethernet, though, let’s look
over either 10BaseT or 100BaseT. This effectively briefly at another approach to networking that can be
doubled the data rate again, because before this more attractive if you only have two or three computers
Ethernet allowed only h a l f d u p l e x or ‘one way at a time’ to be hooked together and you want do it with the least
communication — especially in 10Base5 and 10Base2 possible hassle. This is using USB-USB link cables.
coaxial systems. As you’re no doubt aware, most PCs made since about
Then in 1998 and 1999, the IEEE working group 1996 are fitted with ports for the Universal Serial Bus
released four different implementations of the 802.3z or USB — a medium speed serial interface bus designed
‘Gigabit Ethernet’ standard, achieving 1Gb/s transmission expressly for connecting computers to peripherals like
or another 10-times increase in data transfer rates. The scanners, printers, keyboards, mice, joysticks, modems,
 Jaycar Electronics Tech Update: NETWORKS.PDF (3)
digital cameras, low speed CD-ROM burners and so on.
USB is also supported by most of the recent versions of
Windows: Windows 98, Windows ME, Windows 2000
and Windows XP (but not Windows NT).
One of the big advantages of USB are that it’s ‘Plug-n-
Play’, so cables can be plugged in or unplugged safely
even when the power is on. It also offers a fairly high
data rate of 12Mb/s, although only over relatively short
cables — up to about five metres or so.
USB was designed to connect a single ‘host’ computer
with many (up to 127) slave devices, with a ‘tiered star’
topology. This means it wasn’t really designed for
directly linking two or more computers. (For more
information on USB, see the Reference Data Sheet
USBBUS.PDF, which can be downloaded from our
website). However engineers have recently been able to
design special adapter cables which can be used to link
computers via their USB ports, and software people
have written ‘driver’ software to support networking via
these USB-USB link cables, running under any of the
operating systems which support USB.
Using one of these cables you can usually achieve data
transfer rates of about half the full USB rate, or roughly Here is the Jaycar XC-4845 ‘USB to NET-Linq’
5Mb/s. cable, which can be used to network two or more
PCs via their USB ports...
An example of this type of cable is the XC-4845 USB
to Net-Linq cable available from Jaycar stores and
Electus dealers. Hooking two PCs together using one of install the driver software (supplied on a CD-ROM) on
these is very straightforward; you don’t need to open up one PC to suit its operating system, and then connect
either computer to fit any cards. All that’s needed is to the two computers together via the USB adaptor cable

Fig.3: How the

XC-4845 USB to
NET-Linq cable
shown at above
right can be
used for
networking two
or more PCs
using their USB
ports.
 Jaycar Electronics Tech Update: NETWORKS.PDF (4)
— which plugs into a spare USB port on each machine, b a c k i n g o f f , and the random back-off delays are to try
or on a ‘downstream’ USB port on a hub. The basic idea and ensure that they shouldn’t have a collision with their
is shown in Fig.3(a). The two machines will then form a next attempts.
simple network, with all the usual facilities for file What does an Ethernet data packet or frame actually
transfer, printer sharing and so on. look like? Fig.4 gives you an idea. The main things to
It’s also possible to connect additional PCs (up to 17 note are the destination and source address segments or
in all) to this simple USB network, simply by using fields, which can each be between 2 and 6 bytes long
additional XC-4845 cables and a USB hub. Fig.3(b) (16 - 48 bits), and the data segment itself which can be
shows how this is done. Note that the PC connected to between 46 bytes and 1500 bytes long. We’ll see how
the hub’s upstream port (Computer 3) doesn’t need an those address fields are used in directing the packets
XC-4845 USB link cable — just a normal USB cable. But around the network shortly.
each of the other PCs does need its own XC-4845 By the way, if you were wondering why the Ethernet
cable. standards have a specification for the maximum cable
USB networking is really only suitable if the length between any two device ‘nodes’, it’s because of
computers are all in the same room, fairly close to each the way the CSMA/CD collision detection scheme
other and works. It always
running USB- takes a certain
compatible time for signals
operating to ‘propagate’
systems. It along a cable,
also becomes Fig.4: The basic format used in Ethernet data packets or ‘frames’. Note and this delay
a bit the destination and source address fields, used in directing each packet time is directly
expensive if around a network. proportional to
you want to the cable length.
connect up more than about three PCs. In fact for But for the collision detection scheme to work, each
networking three or more computers, it’s really easier device must be able to receive the collision warning
and cheaper to use 10BaseT or 100BaseT Ethernet signal from any other device before it’s too late to
cables and equipment — especially if the PCs are in respond. So the maximum total ‘round-trip’ propagation
different rooms. So let’s now turn our attention to this time must be less than the Ethernet’s CSMA/CD s l o t
approach to networking. time .
Since cable delay time (in each direction) is the main
Ethernet basics contributor to total propagation time, this sets a limit
As we’ve seen, the most popular system used for local to the maximum cable length between any two PC
area networks or ‘LANs’ is Ethernet, developed from nodes on the network.
the system developed at PARC in 1977 by Metcalfe and This is why the original 10Base5 Ethernet had a
Boggs. And although there are many different maximum node-to-node cable distance of 500 metres,
implementations of Ethernet, they’re all based on the because of its 10mm diameter ‘thick’ coaxial cable. It’s
same basic logical bus topology, the same system of also why 10Base2 Ethernet has a maximum node-to-
sending data in relatively small ‘packets’ or f r a m e s which node distance of 185 metres, because of its thinner
carry the address of both the sending and receiving 5mm diameter coax (RG-58). And of course why
device, and the same method of allowing a lot of data 10BaseT and 100BaseT have a maximum node-to-node
transceivers to share that common bus. This is the distance of 100 metres, because of their use of UTP
method explained in the original Xerox patent, called cable.
carrier sense multiple access with collision detection
(CSMA/CD). 10BaseT basics
Without going too deeply into the technicalities, 10BaseT Ethernet uses low cost ‘Category 3’ (or better)
CSMA/CD essentially works by having each device four-pair UTP cabling of nominal 100Ω impedance to
‘node’ on the network listen for bus activity (i.e., c a r r i e r connect up the computers and other equipment as a
s e n s i n g ) before it tries to transmit a packet of data. This network. All connections are normally made via 8-pin
is like a subscriber on one of the old telephone ‘party RJ45 modular plugs and sockets, which are very much
lines’ picking up the receiver to listen if someone is like the 4-pin RJ11 and 6-pin RJ12 modular connectors
already using the line, before they try to make a call now used for telephones, only slightly larger.
themselves.
The basic connections used for 10BaseT UTP cabling
If a device doesn’t detect any bus activity, it begins
to transmit the packet of data. But of course it’s
possible for another device to begin sending its data
at much the same time, in which case there’ll be a
‘collision’ — two packets of data are present on the
bus at the same time, and the data gets ‘mixed up’.
While the devices are transmitting their data,
they’re also sensing the bus so they can monitor for
any collisions (this is the c o l l i s i o n d e t e c t i o n
function). If they sense the extra bit transitions
produced by a collision, both devices stop
transmitting their data packets and the first device
sends out a special ‘jam sequence’ code — basically a
short collision alarm message. Then both of the 10BaseT and 100BaseT Ethernet both use UTP
devices that were trying to transmit wait short but (unshielded twisted pair) cables, fitted with RJ45
random periods of time before listening for bus modular connectors. Here are some samples of the
activity and trying to transmit again. This is known as ‘patch’ cables sold by Jaycar...
 Jaycar Electronics Tech Update: NETWORKS.PDF (5)
and the RJ45 connectors are
shown in Fig.5. As you can see
only two pairs of wires are
actually used; the other two pairs
are connected, but not used.
Each computer connects to the
network via a n e t w o r k i n t e r f a c e
a d a p t o r c a r d or ‘NIC’, which is
basically a plug-in card containing
a controller to manage the data
interface between that computer
and the network, and a data
transmitter/receiver combination
or ‘transceiver’. In most modern
NICs the controller and
transceiver are combined in a
single LSI chip, which makes the
card very low in cost.
(By the way some of the latest
model PCs have a network
interface built directly into the
motherboard, so they don’t need
the addition of a separate NIC.
They have all the hardware
necessary for networking already
present.) Fig.5: The connections for RJ45 plugs used on Category 3/5 UTP cables
as used for 10/100BaseT networking. Normal ‘straight through’ cables
An important point to have both ends wired as in A; ‘crossover’ cables have one end (only)
remember is that regardless of wired as in B, with the transmit and receive pairs swapped.
whether the PC’s network
interface is in the form of a NIC
or built into the motherboard, it has a fixed and unique provides a range of software drivers, to suit different PC
network or ‘MAC’ (media access control) address which operating systems and/or network operating systems.
is hardwired into it during manufacture. This address is The simplest possible 10BaseT network is shown in
a six-byte (i.e., 48-bit) binary number, which is used by Fig.6. As you can see it’s simply a pair of PCs, each
the network to identify the node at which that PC is fitted with a NIC and with the two NIC ports
connected. The interface or NIC will only ‘accept’ data connected together with a Category 3 or higher rated
packets which carry this address in their distination UTP ‘patch lead’. If the two PCs are running virtually
address field (Fig.4), and will always include the same any modern operating system (i.e., Windows 3.11 or
address code in the source address field of any data later) it’s simply a matter of installing the appropriate
packets it transmits out to the network. software drivers in each computer and they’ll be
Often diagnostic software will represent the NIC’s operating as a fully functional ‘peer to peer’ network.
MAC address as a 12-digit hexadecimal number, such as Data can be transferred between the two in either
054F17B3A8. Not that you normally need to worry direction at 10Mb/s, simultaneously if necessary.
about your PC’s NIC address, of course — the
networking software looks after all that. More speed: 100BaseT
To allow the NIC’s controller to manage the exchange 10 megabits per second is quite fast, of course. Fast
of data between the computer’s processor and all other enough for most home and small office networks, in
computers on the network, you have to install fact. But if you do need even faster networking, this can
networking ‘driver’ software in the computer. NICs be achieved quite easily by using 100BaseT (strictly
usually come with a floppy disc or CD-ROM which 100BaseTX) instead. This is very similar to 10BaseT, and
still uses four-pair UTP cable; the only difference is
that the connecting cable(s) must now be Category
5 rated — so that they can cope with 100BaseT
data rates of up to 100Mb/s. The actual cable
connections are still exactly the same.
For 100BaseT you also need to use NICs which
are rated for 100Mb/s operation, as well. Luckily
most currently available low cost NICs are capable
of operating at either the 10BaseT or 100BaseT
rates, so this isn’t likely to be a problem. Most of
these so-called ‘10/100BaseT’ cards are designed to
plug into a PCI bus card slot in the computer, to
take advantage of the higher speed.
These are the only two real differences between
10BaseT and 100BaseTX — the latter needs
Category 5 cabling and NICs capable of the higher
speed. So the simple two-PC network shown in
The YN-8062 network interface card or ‘NIC’ sold by Fig.6 could operate at either 10Mb/s or 100Mb/s in
Jaycar. Low in cost, it offers 10BaseT or 100BaseT either direction, depending on the rating of the
operation and plugs into a standard PCI card slot. cables and NICs. The maximum length of cable
 Jaycar Electronics Tech Update: NETWORKS.PDF (6)
between the two PCs would be
100 metres.

Adding a hub
What if you need to expand the
simple 10/100BaseT Ethernet
network of Fig.6, by adding more
computers? That’s easy. All you
need to do is install a NIC and
the appropriate driver software
into each additional PC, and
connect them up via a multi-port
10BaseT or 100BaseT h u b . We’ll
look closer at these shortly, but Fig.6: The simplest possible 10/100BaseT Ethernet network, made by
for the moment just think of a fitting a NIC to each of two PCs and linking them with a UTP patch
hub as a kind of data distribution cable (Category 5 rating for 100BaseT). The cable needs to have
box which sends beefed-up ‘crossover’ connections, though — see text. Once the necessary
copies of any data packets driver software in installed in each PC, they’re a network.
arriving at any one of its ports to
all of the other ports. As you’d expect there’s a single RJ45 socket on the
The general arrangement of this kind of hub-based card’s mounting bracket, to accept the network cable.
network is shown in Fig.7, and as you can see the The only other items of interest are a couple of LEDs
network now has a physical ‘star’ configuration or just near the RJ45 socket, which are used to indicate
topology. Each of the PCs is connected to a port on the activity at either the 10BaseT or 100BaseT rates.
hub, so they are all ‘peers’ in the network. The NIC shown is available from Jaycar stores as the
The length of each cable should be kept less than 100 YN-8062, and has a retail price of around $30. It comes
metres, so the maximum total cable length between any complete with a floppy disk containing networking
two PCs is less than 200 metres. This applies regardless driver software to suit a wide range of PC operating
of the proportion of each cable which is open systems (Windows for Workgroups 3.10 and 3.11,
‘patchlead’ and the proportion that is wired permanently Win95, Win98-2000, WinME, Win NT4 and Macintosh)
within walls or suspended ceilings. The other main and networking systems (Lantastic V6.0, NDIS 2.0,
requirement is that all cabling should be rated for Netware 3.1/4.1/5.0, SCO UNIX 5.0 and a TCP/IP
Category 5, especially for 100BaseT operation. packet driver), and also a setup/configuration program.
Incidentally Jaycar also stocks a ‘combo’ NIC which
features both RJ45 and coaxial cable port connectors,
The network interface card making it compatible with both 10BaseT and the older
As we’ve already noted, all except the very latest PCs 10Base2 ‘thin Ethernet’ networks. This card is worth
need the addition of a network interface card or NIC to remembering if you need to replace a NIC in an existing
adapt them for Ethernet networking. As you can see 10Base2 network. It has the Cat. No. YN-8060, and is
from the photo on page 5, a typical 10/100BaseT NIC is only a couple of dollars more than the YN-8062. But
a very small and low cost card which plugs into a PCI note that it’s only capable of 10Mb/s operation, so you
slot, with just about all of the circuitry built into a can’t use it in 100BaseT networks. It too comes with a
couple of ICs. One of the ICs includes the NIC’s hard- floppy disk containing all necessary driver and
wired MAC address. configuration software.

Computer 1 Computer 2

Fig.7: To add
more PCs to
the network,
the simplest
10/100BaseT approach is
Hub or Switch to use a hub
NIC NIC as shown
here.
However for
faster
Computer 3 Computer 4 operation you
can use a
switch
instead, as
explained in
the text.

Cat 5 UTP patch cables

NIC (’Straight Through’ type) NIC
 Jaycar Electronics Tech Update: NETWORKS.PDF (7)
configured for uplinking, you simply use
this hub as the cascaded or ‘expansion’
hub (Hub No.2 in Fig.8), and link the two
hubs together using a normal ‘straight
through’ Cat5 patch cable.
But what if neither hub can be
configured to have an uplink port? There’s
still no real problem — all you need to do
in this case is link the two together using
any of their normal ports, but using a
Cat5 patch cable with ‘crossover’ wiring.
In this case the necessary reversing of the
transmit and receive pairs is provided by
the cable, rather than the wiring inside a
hub. Fig.5(b) shows the connections for
one end (only) of a crossover cable. The
other end is wired as shown in Fig.5(a).
So just remember: when you’re
cascading hubs to expand your network,
either use an uplink port on the lower-
level hub and link them with a normal
‘straight through’ cable, or use normal
ports on each and link them with a
‘crossover’ cable. By the way this same
rule also applies with switches, which
Fig.8: When more PCs need to be added to a 10/100BaseT we’re going to discuss in the next section.
network based on a single hub (or switch), the easiest One final point about cascading hubs
approach is to add another hub or switch and ‘cascade’ and switches: the patch cables used to
them as shown here. interconnect the hubs or switches should
be no longer than five metres long. This is
again to keep network propagation delays
Cascading hubs within the 10BaseT or 100BaseT specifications, for
As we’ve seen the simplest way to hook up more than reliable operation.
two PCs in a network is using a hub, as shown in Fig.7.
Hubs are relatively simple and low in cost, and they’re Switches vs hubs
essentially multi-port ‘repeaters’ or signal booster While you can keep on expanding a network by using
amplifiers. They have no built-in ‘intelligence’; any cascaded hubs, as shown in Fig.8, what you find if you
packet of network data which arrives via the input do this is that before long, the network seems to
connections of any of their ports is simply beefed up become noticeably slower in operation. This slowdown
and sent out again via the output connections of all is due to network ‘congestion’, which arises because of
ports (including the one they came from). the way hubs are ‘dumb’ and simply boost any data
As low cost hubs are available with up to eight ports, signals which arrive at any of their port inputs, and
this means that the simple hub-based network scheme broadcast them out again to all ports.
shown in Fig.7 can be used to link up as many as eight So in a network hooked up via hubs, every PC’s NIC
computers. Jaycar stores sell two suitable Nexus receives every data packet sent over the network, and
10BaseT hubs for this, the YN-8070 Five-port model it’s up to the NIC and its driver software to inspect
and the YN-8072 Eight-port model. Both are very every packet and ‘ignore’ all of those which are
compact and run from a small plug pack. intended for another PC. It’s like a telephone system
What about networks with more than eight PC’s? hooked up as an enormous party line, with no
When you want to expand past eight, the simplest switchboard. And because of the huge amount of data
solution is to add a second hub connected in ‘cascade’ sent to each NIC all the time, the network slows down.
with the first. This is shown in Fig.8. The second hub To solve this problem, or at least minimise its impact,
connects to one port of the first, in place of one of the
original PCs.
There’s an important point to note about this
cascading of hubs, though. For the cascading to work
properly in terms of network operation, there must be
a ‘crossover’ connection between the two hubs. In
other words, the input connections at one end of the
hub-to-hub cable must connect to the output
connections at the other, and vice-versa.
Many hubs are designed so that one of their ports can
have these connections swapped over inside with a
switch, so that by using the switch you can configure
that port as a ‘Uplink’ port for cascading. With the This very compact 10BaseT five-port hub is very
switch in the ‘Normal’ position, the port is configured suitable for small networks. One of its five ports
just like all the others, to connect to a NIC in a PC. can be configured as an ‘uplink’ port, with the
Both of the hubs sold by Jaycar have one port which can connections internally crossed over. Power comes
be configured in this way, for example. from a small ‘plug pack’. The Nexus unit shown
If you do have a hub with a port which can be is sold by Jaycar stores as YN-8070.
 Jaycar Electronics Tech Update: NETWORKS.PDF (8)
switches, Jaycar offers two Nexus models — both rated
OR gate Buffer Amp
for 10/100BaseT operation. The YN-8082 is a five-port
switch, while the YN-8084 provides eight ports. Both
have one port which can be used either as a normal
port to connect to a NIC, or as an uplink port to
connect to another switch or hub for cascading with a
straight-through cable.
Note that both of these switches are capable of
10/100BaseT operation (i.e., up to 100Mb/s), whereas
you’ll remember that the two low-cost hubs currently
Port 1 Port 2 Port 3 Port 4 Port 5 stocked by Jaycar are only capable of 10BaseT (10Mb/s)
(A) Simple 5-Port Hub operation.
Do you have to use either hubs OR switches, or can
you mix the two? You can always use a combination of
Packet Memory Packet Address the two if you want. Replacing your top-level hub with a
Address and Analyser, Memory, switch will generally give a big improvement, even if you
Analyser Switching Crosspoint Switches
Controller & Buffer Amps still use hubs at the lower levels. As switches are usually
twice the price of a hub with the same number of ports,
this kind of mix-and-match combination can be very cost
effective.
For example a combination of an eight-way switch at
the top level with a couple of five-way hubs at the next
level down, as shown in Fig.10, will usually give quite
speedy operation for up to 14 PCs. Replacing the two
lower-level hubs with switches will certainly give an
additional speedup, but often not enough to justify the
extra cost.
In short the decision about using switches instead of
hubs is really up to you, because it depends largely on
Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 the amount of money you have available to invest in
(B) N-Way Switch (8-way) networking and the degree of network congestion
slowdown you’re prepared to tolerate.
Fig.9: Diagrams showing the difference between a Note though, that if are using a switch at the top level
hub and a switching hub or ‘N-way switch’. The and your network includes a PC shared as a network
latter is much smarter, directing the data packets. resource by all the other PCs — such as a print server,
a server for a CD-ROM drive tower or hard disk RAID
(redundant array of inexpensive drives) array, or a high
the simplest approach is to use switching hubs or speed internet connection — this machine or machines
s w i t c h e s instead of normal hubs. Switches may look very should be connected directly to a port on the top level
similar to hubs, but they’re the next step up in terms of switch. Don’t connect servers to the lower level hubs
‘intelligence’. Instead of simply boosting every incoming or switches, or most of the potential efficiency of the
data packet or frame and broadcasting it to all ports, a switch won’t be realised.
switch checks the source and destination fields in each
frame (see Fig.4), to work out where that frame has Wireless networking
come from and where it should be sent. It also has an
internal memory where it stores the hardwired network You’ve probably heard about wireless networking —
address of each NIC that is currently connected to its networking computers using radio waves instead of
ports (or the addresses of the NICs that are connected cables. So just before we finish up we’d better give you
elsewhere in the network, via its uplink port). And a basic understanding of what this is all about.
finally, it has a ‘crosspoint’ switch array, with a set of Practical wireless networking dates from 1997, when
electronically controlled switches so that it can direct the IEEE published its 802.11 standard for wireless
any incoming data frame to the output pair of just one
port — the port which connects to the NIC
corresponding to its destination address.
So if you like, a switch is much ‘smarter’ than a hub,
and much more like a telephone switchboard. By
directing each packet of data only to the NIC it’s
intended for (or at least the hub or switch to which that
NIC is connected), a switch cuts down the network
congestion significantly. Because each NIC now only
receives data that is specifically addressed to it, there’s
now much less risk of data collisions too. As a result
the network can operate at much closer to full speed.
The basic differences between a hub and a switch are
shown in Fig.9. As you can see there’s a lot more in a
switch, to give it the intelligence to remember the NIC
addresses, work out the destination of each data packet As you can see, a five-port switch looks very
and send it only to the port leading that NIC’s address. similar to a five-port hub. However it has the
capability to give much speedier network
If you want to take advantage of the significant operation. This Nexus 10/100BaseT unit is sold by
increases in network efficiency and speed offered by Jaycar as the YN-8082.
 Jaycar Electronics Tech Update: NETWORKS.PDF (9)

Fig.10: Can you mix

switches and hubs?
You certainly can.
Here’s a network of
14 computers, with
an eight-port switch
at the top level and
two five-port hubs
connected to it in
cascade. Note that
servers and other
network resources
should be connected
to the top-level
switch, for the most
efficient operation.

Ethernet LANs. This originally used data transceivers The current price of an 802.11b ‘access point’ (the
sharing frequencies in the 902 - 908MHz UHF band, but actual wireless transceiver, combined with a NIC or a
the equipment was quite expensive and subject to USB controller to hook up to a PC) is typically around
interference. More recently ‘802.11b’ transceivers using $700, while the PC-card NIC/transceiver cards needed
frequencies in the 2.40 - 2.43GHz microwave band have for the wireless-linked PCs are typically around $200
appeared, offering better performance at a lower price. each. So even to hook up a pair of PCs using 802.11b
Even more recently some of the ‘802.11a’ transceivers wireless networking will currently cost around $900 —
use even higher microwave frequencies at around 5GHz, more than 10 times the cost of a pair of 10/100BaseT
offering higher speed but at a higher price. NICs and a crossover cable.
Apart from using radio waves instead of copper-based When you bear in mind that 802.11b only delivers
cables, 802.11 wireless networking works in very much about 5Mb/s, this cost may be hard to justify. However if
the same way as normal wired Ethernet like 10BaseT. you want networking without the hassle of cables, it
The main differences are in operating speeds and price. may still be worth considering.
Wireless networking equipment designed to the This year equipment designed to the newer 802.11a
802.11b specification (also known as ‘Wi-Fi’) can specification (also called Wi-Fi5) has also become
theoretically give data rates up to 11Mb/s — a whisker available. This does offer higher speed than 802.11b,
faster than 10BaseT. However in practice typical typically achieving 22Mb/s over short distances (about
802.11b network links rarely achieve rates higher than 5m) and 13Mb/s over medium distances (about 10-12m).
about 5Mb/s. In other words, 802.11b typically delivers However the cost is even higher than 802.11b
around half the speed of 10BaseT. equipment, with an access point typically costing $1200
and PC Card NIC/transceiver adaptors between
$400 - $500 each. So at present you’ll pay quite a
premium for that increase in speed.
No doubt the cost of 802.11b wireless
networking equipment will come down in time,
making it more attractive. However until then,
most people are likely to find 10/100BaseT wired
Ethernet the most appealing proposition from a
cost point of view.
Incidentally both 802.11b and 802.11a offer
lower data security than wired Ethernet, because
of the wireless links involved. Both varieties of
802.11 employ data encryption to increase
security, called Wired Equivalent Privacy (WEP).
However this does appear to be vulnerable to
hacking. Of course this isn’t likely to be much of a
problem for home networks, or even a network
for a small business.
Jaycar also sells this ‘combo’ NIC (YN-8060), which is
compatible with both 10BaseT and 10Base2 networks. (Copyright © 2002, Jaycar Electronics)
 Jaycar Electronics Tech Update: NETWORKS.PDF (10)

Networking Jargon Explained

10Base2 : 10Mb/s Ethernet networking using a 5mm diameter 50-ohm coaxial cable as the transmission medium. Also known as
‘cheaperNet’ or ‘thin Ethernet’ (IEEE spec 802.3a-1985).
10Base5 : The original 10Mb/s Ethernet, using a 10mm diameter 50-ohm coaxial cable as the transmission medium. Also known as
‘thick Ethernet’ (IEEE spec 802.3-1983).
10BaseT : 10Mb/s Ethernet using two pairs of 100-ohm UTP cable rated to Category 3 or better.
100BaseT : 100Mb/s Ethernet, usually using two pairs of 100-ohm UTP cable rated to Category 5. Also called ‘Fast Ethernet’.
1000BaseT : 1Gb/s or ‘Gigabit’ Ethernet, using four pairs of Category 5 UTP cable, or twinax, or lasers and optical fibres.
Bridge : A piece of Ethernet networking equipment which can be used to link two separate ‘domains’. Essentially a switching hub or
switch, but with only two ports.
Category 3 cabling : Unshielded twisted-pair cabling which is manufactured to specifications such that it will support 10Mb/s data
transmission.
Category 5 cabling : Unshielded twisted-pair cabling which is manufactured to specifications such that it will support 100Mb/s data
transmission.
CSMA/CD : Carrier Sense Multiple Access with Collision Detection — the basic principle used in Ethernet networks, to allow many
computers to share the data transmission medium.
Ethernet : The data networking system developed at Xerox in 1977 by Metcalfe and Boggs. Now the most popular system for LANs.
Fast Ethernet: Another name for 100BaseT Ethernet, running at a data rate of 100Mb/s (ten times the rate of 10BaseT).
File server : A computer connected to a LAN which provides file storage resources to the other ‘client’ machines. It may have a RAID
array of hard disks, a rack or ‘tower’ of CD-ROM drives, or both.
Gigabit Ethernet : Ethernet networking technology which offers a data transmission rate of 1Gb/s (1000Mb/s).
Hub : A ‘dumb’ signal booster and interfacing device for Ethernet networking, which simply takes any incoming data arriving at any of
its ports, and rebroadcasts it to all of its port outputs.
IPX/SPX : Logical protocols used in Netware.
LAN : A Local Area Network, linking a group of computers together in roughly the same physical location.
MAC: Media Access Control, the method used to regulate the way each network device can access the transmission medium. Uses the
unique hardware address given to each NIC when it’s manufactured.
NIC : The network interface adaptor card, which is used to provide each computer with its network data interface and transceiver
(and also its unique hardware address on the network).
Print server : A computer, connected to a network, which is dedicated to managing a printer resource.
RAID array : A Redundant Array of Inexpensive Drives, with multiple hard disk drives connected in such a way that they offer a large
amount of highly reliable data storage. Often managed by a ‘file server’ computer, to provide bulk data storage for a network.
RJ45 connectors : Compact modular connectors with 8 contacts, developed from the smaller RJ11 and RJ12 telephone connectors.
(The ‘RJ’ simply stands for registered jack.)
Repeater: A ‘dumb’ signal booster and interfacing device for Ethernet networking. Very much like a hub, but with only two ports.
Router : An even more ‘intelligent’ version of a switching hub or ‘switch’, used to interconnect multiple networks — or a network and
the internet.
STP : Shielded twisted-pair cable, as opposed to unshielded twisted pair cable.
Switch : An intelligent switching hub which analyses the source and destination address codes in the header of each data packet or
frame arriving at one of its ports, and directs the packet only to the output port which connects to the NIC with that destination
address. This reduces network congestion and hence increases speed.
TCP/IP : Transmission Control Protocol/Internet Protocol, the main logical data exchange protocol used on the internet and for LAN-
internet communication.
Thick Ethernet : The original 10Base5 Ethernet of 1983, using 10mm diameter coaxial cable for 10Mb/s networking.
Thin Ethernet : 10Base2 Ethernet, using 5mm diameter coaxial cable for 10Mb/s networking.
USB network bridge cable : An adaptor cable which allows networking between two PCs, or between multiple PCs, using their USB
ports.
UTP : Unshielded twisted pair networking cable, usually with four pairs of insulated wires and with each pair of wires twisted together
to minimise interference. Available with a Category 3 rating to support 10Mb/s transmission, or a Category 5 rating to support
100Mb/s transmission.
WEP : Wireless Equivalent Privacy, the data encryption system used in 802.11a/b wireless networking. It is intended to offer a level of
security equivalent to that of wired Ethernet.
Wi-Fi : Another name for 802.11b wireless networking technology, using frequencies in the 2.4GHz UHF band. Offers data rates up to
about 5Mb/s.
Wi-Fi5 : Another name for the newer 802.11a wireless networking technology, which uses frequencies at around 5GHz and offers data
rates up to about 22Mb/s.
Wireless networking : Linking computers via radio waves rather than copper wires or optical fibres. (IEEE specs 802.11a/b)

(Copyright © Jaycar Electronics, 2002)