11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles
WHEELS, CARBON STEEL
Specification
M-107/M-208

IMPLEMENTED 07/2009

Adopted: 1962; Revised: 1994, 2004, 2006, 2007, 2009

1.0 SCOPE
These specifications cover one-wear, two-wear, and multiple-wear wrought and cast carbon steel
wheels for locomotives and carsClasses L, A, B, and C (heat-treated) wheels used in interchange
service. All freight car wheels manufactured for AAR interchange service must be heat-treated
and of a low-stress design.
1.1 Class B or C wheels must be used for freight cars in interchange service.
1.2 Class B or C wheels are recommended for use on locomotives.
1.3 For passenger car service, the various classes are intended generally as follows:
Class L High-speed service with more severe braking conditions than other classes and light
wheel loads.
Class AHigh-speed service with severe braking conditions, but with moderate wheel loads.
Class BHigh-speed service with severe braking conditions and heavier wheel loads.
Class C(1) Service with light braking conditions and heavy wheel loads.
(2) Service with heavier braking conditions where off-tread brakes are employed.
2.0 DESIGN
2.1 Standard wheel types and tread and flange contours for freight car and locomotive steel
wheels shall be as shown in this specification. Interchangeability requirements and tolerances and
tread and flange contours for the authorized wheel types are shown in Figs. B.8 through B.14. The
interchangeability requirements and tolerances are generally limited to those required to ensure
the wheel is compatible with the standard axles, bearings, side frames, and track. In the event
that design constraints other than these are shown, the wheel producer may request an exception
or change by application, with supporting data, to the AAR Technical Services Division (hereinafter termed AAR). Staff will, in turn, submit the application to the Wheels, Axles, Bearings, and
Lubrication (WABL) Working Committee (hereinafter referred to as the Committee) for review.
2.2 In the event any company feels there is a need for a wheel type not currently listed, an application, with supporting data, should be made to the AAR, who will obtain the decision of the Committee.
3.0 Authorization for delivery for interchange use of any AAR wheel type must be obtained from
the AAR as described in Appendix A.
4.0 Qualification as a manufacturer of wheels for use in AAR interchange service must be in
accordance with Appendix B. Qualification is effective until revoked for cause by the Committee.
Failure to maintain reasonable quality standards in manufacturing is an example of cause.

11/1/04

G [M-107/M-208] 1

11/1/04

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

5.0 MANUFACTURE
5.1 Discard
A sufficient discard shall be made from the steel used for the manufacture of all steel wheels to
ensure freedom from piping and undue segregation.
5.2 Temperature Control
During manufacture of all wheels, necessary care in the regulation of temperature gradients shall
be exercised to prevent the development of internal defects or injurious stresses.
6.0 HEAT TREATMENT

6.2 Rim-Quenching Treatment

All wheels shall be allowed to cool to a temperature below the critical range and uniformly
reheated to the proper temperature to refine the grain, and then the rims shall be quenched. Following quenching, the wheels shall be charged into a furnace for tempering to meet the requirements of paragraph 10.0 and subsequently cooled under controlled conditions.
7.0 SHOT PEENING
7.1 Scope
This section covers shot peening of steel wheels to provide improvement in plate fatigue strength.
7.2 Requirements
7.2.1 Shot
The shot shall be SAE No. 550 or larger hardened steel as specified in SAE J827.
7.2.2 Shot Size Control
The peening machines shall be equipped with a separator for continuously removing broken shot.
Sufficient new shot shall be added to ensure that a minimum of 85% of No. 550 or larger shot is
maintained in the machines at all times.
7.2.3 Peening Intensity
The peening intensity shall be sufficient to produce an average arc height of not less than
0.008 (.0075 +) Almen C on the front plate near the hub fillet and on the back plate near the rim
fillet of wheels of the standard design and at back plate hub fillet and front plate rim fillet of the
reverse plate design. The area to be peened is defined as the plate area extended approximately
one-half of the way into the hub and rim fillet radii on the front and on the back of the wheel.
7.2.3.1 Arc Height Measurement
Measurements of arc height shall be made in accordance with SAE Standards J442 or SAE Recommended Practice J443.
7.2.4 Coverage
The minimum peening time shall be sufficient to ensure that full coverage is attained on the
Almen C strip as defined in SAE Recommended Practices J443, Alternate Procedure, or
MIL-S-13165 C, Paragraph 6.11
7.2.5 Sequence
Shot peening will be performed on all wheels and after any corrective surface preparation on the
plate area. Plate area is defined in paragraph 7.2.3. Peening may be performed prior to inspection.

G [M-107/M-208] 2

11/1/04

IMPLEMENTED 07/2009

6.1 All wheels must be rim-quenched and tempered.

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

7.2.6 Portable Peeners

A portable peening device may be used to re-peen small reconditioned areas (no larger than 6 in.2)
on wheel plate surfaces, excluding the critical fillet areas (front hub and back rim fillets of wheels
of standard designs and back hub and front plate fillets of wheels of reverse plate design). The portable equipment must be capable of peening an Almen C strip to develop the required average arc
height of not less than 0.008 in. with a reasonable time of peening. Peening time of wheel plates
must be at least as long as the time required to develop the 0.008-in. arc height. The equipment
must be tested on an Almen C strip each 8-hour shift that the portable peener is used. A record of
the Almen C test results shall be maintained.

IMPLEMENTED 07/2009

7.3 Quality Assurance Provisions

7.3.1 Wheel Surface Condition
The peened appearance of rim and hub shall not be cause for rejection.
7.3.2 Frequency of Test
Arc height determinations shall be made on Almen C strips attached to a test wheel at the beginning and end of each production run but not less than once in each eight operating hours.
7.3.3 Retest
If a test fails to meet the arc height requirements of 0.008 Almen C, two retests will be made.
These retests shall be averaged with the first determination. The average shall be not less than
0.008, and no more than one value of the three shall be less than 0.008.
7.3.4 Repeening
When test values fail to meet the provisions of paragraph 7.3.3, corrective action shall be initiated
and satisfactory test values secured before proceeding with production peening. If the average
Almen value of the unsatisfactory test is 0.006 or 0.007, the last half of the wheels peened prior to
the unsatisfactory test (but subsequent to a satisfactory test) shall be repeened with at least 1/2
exposure time. If the average Almen value is less than 0.006, all the wheels peened since the last
satisfactory test shall be repeened with full exposure.

11/1/04

G [M-107/M-208] 3

11/1/04

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

8.0 LADLE ANALYSIS

8.1 The steel shall conform to the following chemical requirements:
Table 8.1 Chemical requirements
Element

Nickel
Chromium
Molybdenum
Vanadium
Copper
Aluminum
Titanium
Colunbium (niobium)

0.25 max.a/
0.25 max.a/
0.10 max.a/
0.040 max.a/
.35 max.
0.060 max.
0.03 max.
0.05 max.

a/

Class A
0.470.57
0.600.90
0.030 max.
0.0050.040
0.151.00
Residual Elements
0.25 max.a/
0.25 max.a/
0.10 max.a/
0.040 max.a/
.35 max.
0.060 max.
0.03 max.
0.05 max.

Ladle Analysis (%)

Class B
0.570.67
0.600.90
0.030 max.
0.0050.040
0.151.00

Class C
0.670.77
0.600.90
0.030 max.
0.0050.040
0.151.00

0.25 max.a/
0.25 max.a/
0.10 max.a/
0.040 max.a/
.35 max.
0.060 max.
0.03 max.
0.05 max.

0.25 max.a/
0.25 max.a/
0.10 max.a/
0.040 max.a/
.35 max.
0.060 max.
0.03 max.
0.05 max.

If the manufacturer chooses to vary from the above limits for nickel, chromium, molybdenum,
and vanadium, the following formula must be met:
930 [570 % carbon] [80 % manganese] [20 % silicon] 50 % chromium] [30 % nickel] [20 % molybdenum + % vanadium] > 390

8.2 An analysis of each heat of steel shall be made by the manufacturer to determine the percentage of the elements specified in paragraph 8.1. This analysis shall be made on a test specimen
taken during the pouring of the heat. The chemical composition thus determined, together with
such identifying records as may be desired, shall be reported to the purchaser or purchasers representative and shall conform to the requirements specified in paragraph 8.1.
8.3 Chemical Analysis
Chemical analysis of each heat of steel shall be made by one of the test methods listed below. All
analyses should note which method is used for the carbon and/or chemical determinations.
8.3.1 Test Method 1
The carbon determinations should be one of the following test methods:
8.3.1.1 Total carbon by the combustion gravimetric method, ASTM E-350 Standard Test Methods for Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron,
and Wrought Iron.
8.3.1.2 Total carbon by the combustion thermal conductivity method, ASTM E-1019 Standard
Test Methods for Determination of Carbon, Sulfur, Nitrogen, Oxygen, and Hydrogen in Steel and
in Iron, Nickel, and Cobalt Alloys.
8.3.1.3 Total carbon by combustion, followed by quantitative infrared analysis, ASTM E-1019
Standard Test Methods for Determination of Carbon, Sulfur, Nitrogen, Oxygen, and Hydrogen in
Steel and in Iron, Nickel, and Cobalt Alloys.

G [M-107/M-208] 4

11/1/04

IMPLEMENTED 07/2009

Carbon
Manganese
Phosphorous
Sulfur
Silicon

Class L
0.47 max.
0.600.90
0.030 max.
0.0050.040
0.151.00

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

IMPLEMENTED 07/2009

8.3.2 Test Method II

ASTM E-415 Standard Test Method for Optical Emission Vacuum Spectrometric Analysis of Carbon and Low-Alloy Steel.
8.4 Check Analysis
An analysis may be made by the purchaser from a sample furnished by the manufacturer that represents the heats, from a wheel block, or from finished wheels selected by the purchaser from each
heat in question. Samples from wheel blocks must be drilled from the end of the block midway
between the center and outside. When a finished wheel is used, the sample must be obtained from
the rim face or the hub in a manner that will not impair the usefulness of the wheel. No drilling of
the finished wheel plate is permitted. Each sample must be thoroughly mixed together and must
be clean and free of oil, scale, and other foreign substances.
8.4.1 Sampling Method
When wheel blocks or whole wheels are not available for chemical analysis, the laboratory conducting the chemical analysis shall follow a standard sampling method. This standard method of
sampling shall be ASTM E-1806, Standard Practice for Sampling Steel and Iron for Determination of Chemical Composition. Then use either ASTM E-350, E-1019, or ASTM E-415 as specified
in paragraph 8.3 for chemical analysis of the sample.
9.0 INTERIOR CONDITION/MICROCLEANLINESS STANDARDS
9.1 Sample Frequency
The metallurgical cleanliness of the wheel steel shall be determined from samples taken from randomly selected finished wheels representing the heat. A minimum of one 33-in. wheel and one
36-in. wheel of different heats produced quarterly per facility shall be tested.
Facilities that produce only 33-in. or 36-in. wheels shall test two wheels of different heats
quarterly.
Facilities producing different size wheels to AAR specifications during a quarter shall test
at least two wheels of different heats during the subject quarter.
Facilities not producing wheels to AAR specifications during four successive quarters shall,
at a minimum, test at least two wheels from a heat specially produced to AAR specifications for the scheduled facility certification continuation inspection once a year.
The purchaser reserves the right to more frequent testing should it be deemed necessary by
mutual agreement between the purchaser and producer.
9.2 Sample Size and Location
A minimum of six samples shall be taken from each wheel tested approximately equidistant
around the circumference of the wheel. Each sample shall be 7/8 in. long in the circumferential
direction (the rolling direction), 3/4 in. wide in the axial direction (the rim width), and 1/2 in. thick
in the radial direction (the rim thickness). The circumferential surface for microcleanliness evaluation shall be located 1/2 in. below the wheel tread and 2 1/2 in. to 3 1/4 in. from the back rim face.
Dimension tolerances are 1/8 in.

11/1/04

G [M-107/M-208] 5

11/1/04

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

9.3 Sample Preparation and Evaluation

9.3.1 Each 7/8 in. 3/4 in. 1/2 in. sample shall be carefully prepared and evaluated to ASTM
Standard Practice E1245. The flicker method shall be used to establish the correct setting of the
gray-level threshold limits.
9.3.2 The total area evaluated for each sample shall be not less than 1/4 in.2 or 161 mm2. All
inclusions greater than 2.5 m shall be counted. The WABL Committee must approve alternates
to this method.

9.3.4 Each sample shall be permanently marked according to heat and wheels represented and
retained for a period of 1 year after the wheels are shipped. Records of test results shall be kept for
10 years after the wheels are shipped. Inspection results will be available for review by the AAR or
other interested parties. AAR or other interested parties may have the test samples evaluated by
other accredited laboratories at their expense.
10.0 BRINELL HARDNESS
10.1 The hardness of the rim, when measured in accordance with the requirements of
paragraph 10.2, shall show the following values:
Table 10.1 Brinell hardness of rim
Class
L
A
B
C
D

Minimum Hardness
197 BHN
255 BHN
302 BHN
321 BHN
341 BHN

Maximum Hardness
277 BHN
321 BHN
341 BHN
363 BHN
388 BHN

Note: Class D alloy steel wheels must meet all chemical requirements for Class C wheels and have
approval of the AAR WABL Committee.
10.2 Method of Measurement
Measurement must be made in accordance with ASTM E-10 (latest revision) on the front face of
the rim with the edge of the impression not less than 3/16 in. from the radius joining face and
tread. Before making the impression, any decarburized metal shall be removed from the front face
of the rim at the point chosen for measurement. The surface of the wheel rim shall be properly prepared to permit accurate determination of hardness.

G [M-107/M-208] 6

11/1/04

IMPLEMENTED 07/2009

9.3.3 Effective January 1, 2008, average and worst field area percentage oxides, voids, and sulfides will be recorded. The AAR shall be advised quarterly when the six samples representative of
the heat tested average more than 0.100% oxide plus voids; or the worst field area percentage of
any one sample is more than 0.750% oxide plus voids; or 0.750% sulfides. If AAR is advised in two
successive quarters, the provisions of AAR Manual of Standards and Recommended Practices,
Administrative Standards, Standard S-060, paragraph 5.3, shall apply. In such cases, a special
facility inspection may be required to demonstrate that the root cause has been identified and
addressed.

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

11.0 NUMBER OF TESTS

11.1 Where continuous heat-treating furnaces are used, BHN measurements shall be made on
10% of the wheels from each heat. Where batch-type heat-treating furnaces are used, BHN measurements shall be made on 10% of the wheels from each heat-treatment lot. For batch-type
heat-treating, at least one wheel from each heat in the heat-treatment lot must be tested. For
either heat-treatment process, BHN measurements must be made on a minimum of one wheel in a
heat or heat-treatment lot of 10 or less, and on a minimum of 2 wheels in a heat or heat-treatment
lot of 11 to 20.

IMPLEMENTED 07/2009

11.2 If all the wheels tested meet the requirements of paragraph 10.0, all of the wheels represented shall be accepted.
11.3 If any wheel tested fails to meet the requirements of paragraph 10.0, it shall be checked by
making two additional hardness measurements, one on each side of the point first measured and
each approximately 1 in. from that point. If both of these check measurements meet the requirements of paragraph 10.0, the wheel shall be considered to have met the requirements of
paragraph 10.0.
11.4 When continuous heat-treating furnaces are used, should any of the wheels tested fail on
check test to meet the requirements of paragraph 10.0, the manufacturer may test for individual
hardness measurements all of the wheels of that heat in the lot submitted for inspection, and
those meeting the requirements of paragraph 10.0 shall be accepted. Where batch heat-treating
furnaces are used, should any of the wheels tested fail on check test to meet the requirements of
paragraph 10.0, the manufacturer may test all of the wheels in the heat-treatment lot for individual hardness measurement, and those meeting the requirements of paragraph 10.0 shall be
accepted.
11.5 On new wheel designs or existing designs to which process changes are made, hardness
gradient tests shall be performed on a minimum of one wheel from each of the first five heats of
steel produced. The hardness shall be taken per Fig. 11.1 utilizing an approved hardness test
machine. Values shall meet the requirements as shown in Table 11.1.
Table 11.1 Acceptable hardness ranges
Class
B
C
D

Minimum
285 HB
28 Rc
301 HB
30 Rc
321 HB
32 Rc

Maximum
341 HB
40 Rc
363 HB
42 Rc
388 HB
42 Rc

If values do not meet the requirements in Table 11.1, an additional five wheels from five heats
shall be tested. All five wheels must meet the requirements in Table 11.1. If one or more wheels
fail to meet the requirements in Table 11.1, testing per paragraph 11.5 shall be repeated after a
process and/or design change is made. All wheels from heats that have a test wheel that failed to
meet the requirements in Table 11.1 shall be reheat-treated, and one wheel from the heat shall be
tested. If this wheel fails to meet the requirements in Table 11.1, all wheels from the heat shall be
scrapped. Only one reheat treatment shall be allowed.

11/1/04

G [M-107/M-208] 7

11/1/04

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

12.0 RETREATMENT
Any wheel failing to meet the requirements of paragraph 10.0 may be retreated and tested in
accordance with paragraph 11.0.
13.0 MATING
Wheels shall be measured and marked to the lower tape number until the next graduation is
reached. Wheels shall be shipped in pairs of the same measured tape size.
14.0 GAUGES
The gauges and tapes shall conform to and be used as required by the standards of the AAR Technical Services Division Alternate tape gauging will meet or exceed the AAR measurement standard for taping wheels. The repeatability and reproducibility of all alternate gauges must be
demonstrated.
15.0 PERMISSIBLE VARIATIONS
15.1 The wheels shall conform to the dimensions with tolerances as specified in Figs. B.8, B.9,
B.11, and B.12 for freight car wheels and in Figs. B.8 and B.10 for locomotive wheels.
15.2 Where Figs. B.9 and B.10 allow a certain percentage of the wheels to vary from standard
dimensions for tape size by a given amount, the percentage of such wheels shipped by any manufacturer shall not exceed this percentage during a calendar year. No individual purchaser may
receive more than this percentage of his daily shipments of such wheels except by agreement with
the manufacturer.

G [M-107/M-208] 8

11/1/04

IMPLEMENTED 07/2009

Fig. 11.1 Hardness mapping locations

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

16.0 FINISH
16.1 Wheels shall be rough bored and shall not have black spots in the rough bore. Front hub face
of wheels (1-W, 2-W, and MW) shall be parallel to the plane of the vertical reference line and may
be smooth forged, cast, or machined. The back hub face may be smooth forged, cast, or machined.

IMPLEMENTED 07/2009

16.2 The contour of tread and flange shall be as shown in Figs. B.11, B.12, or B.13 as applicable.
Wrought steel wheels must be machined and finished smooth without excessive tool chatters. Cast
steel wheels shall be as cast, machined, or ground, at the option of the manufacturer. Minimum and
maximum flange thickness, height, and throat radii gauges shown in Standards S-661 and S-662
shall be used to check proper profile. Wheels that do not meet the criteria must be scrapped or recontoured.
16.3 Wheels must be free of all condemnable in-service defects. As-produced surfaces must be
free from abrupt changes in surface contours. Spot grinding or machining to remove surface
defects must not exceed a depth of 1/8 in. (0.125 in.; 3.2 mm). Sectional properties must meet all
dimensional requirements following repair of surface defects. Repaired surfaces must have a maximum surface roughness of 500 in. prior to final shot peening. Repaired surfaces must provide a
uniform transition to the as-produced surfaces.
16.4 Wheels shall not be covered with any substance to such an extent as to hide defects.
16.5 Wheel profile is to be checked using wide flange profile gauge shown in Fig. B.14. There will
be no more than 1/32-in. variation from the profile.
17.0 MARKING
17.1 Identification markings shall be legibly stamped as shown in Figs. B.4 or B.5. Wheels for
freight service must be hot stamped or cold stamped on the back hub face. If any stamped characters are missing or illegible, these shall be replaced by cold stamping in the proper place in the
marking sequence. Passenger car wheels may be hot stamped or cold stamped on front or back (as
specified by purchaser) hub face. When ordered, locomotive wheels may be hot or cold stamped on
the back rim face; or hot or cold stamped on the front hub face; or hot or cold stamped on the back
hub face providing finish machining will completely remove the markings on the back hub face.
Locomotive wheels that are to receive final hub machining by the purchaser may be ordered with
markings paint stenciled on the wheel plate. After final machining, the purchaser will cold stamp
the markings on the front hub face. For wheels having raised cast-on markings, the markings shall
be legible characters and be as shown in Fig. B.7. For all wheels, stamping should be centered
approximately on the hub. No wheel manufactured after May 1, 2009, may be bored and applied
with any portion of the wheel manufacturers hub stamp closer than 1/8 in. from the inner hub
diameter and no closer than 1/8 in. from the outer hub diameter. No wheel manufactured before
May 1, 2009, may be bored and applied with any portion of the wheel manufacturers hub stamp
breaking over the edge of the inner or outer hub diameter.
17.2 The tape size of all wheels shall be paint stencilled on back plates in characters at least 1 in.
high. An H shall also be paint stencilled on the front plate at least 1 in. in height on those wheels
of curved plate, heat-treated configuration. Stencil paint must be white and have a minimum service life of 1 year.

11/1/04

G [M-107/M-208] 9

11/1/04

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

18.0 INSPECTION
18.1 The inspector representing the purchaser shall have free entry, at all times while the work
on the purchasers contract is being performed, to all parts of the manufacturers works that concern the manufacture of wheels ordered. The manufacturer shall afford the inspector, free of
charge, all reasonable facilities and necessary assistance to satisfy the inspector that the wheels
are being furnished in accordance with these specifications. Internal defects are usually detected
by ultrasonic testing. Such test shall be used in the manufacture of all wheels. The method to be
followed and the equipment to be used shall comply with the requirements as shown in
paragraph 18.4. Tests and inspection shall be made at the place of manufacture prior to shipment,
unless otherwise specified.

18.3 All tests and inspections shall be so conducted so as not to interfere unnecessarily with the
operation of the works.
18.4 Ultrasonic Inspection
For detecting internal discontinuities in the rim of all steel wheels, ultrasonic inspection shall be
made by following either the procedures shown below or an AAR-approved equivalent. Equipment
used in these procedures shall comply with the following requirements.
Each manufacturer shall maintain a documented test method and procedures for ultrasonic
inspection of all railroad wheels manufactured under this specification.
18.4.1 Equipment
18.4.1.1 The instrument shall have a pulse echo receiver and shall operate at frequencies of 2 to
5 MHz required for the test method and type of equipment used.
18.4.1.2 The transducers shall be of the type whose composition and dimensions are appropriate
for the test method used.
18.4.1.3 The ultrasonic inspection shall be performed with an automated scanning system. An
automatic flaw alarm system shall be used in conjunction with the ultrasonic instrumentation.
18.4.1.4 A suitable couplant shall be used between the test surface and the transducer. The couplant shall be free of air bubbles. Rust inhibitors, softeners, and wetting agents may be added to
the couplant.
18.4.2 Time of Inspection
Inspection shall be performed after final thermal processing.

G [M-107/M-208] 10

11/1/04

IMPLEMENTED 07/2009

18.2 The purchaser may make tests to govern the acceptance or rejection of the wheels in purchasers own laboratory or elsewhere. Such tests shall be made at the expense of the purchaser.

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

18.4.3 Calibration
18.4.3.1 Calibration shall be conducted using a reference standard of a wheel or portion of a
wheel rim containing simulated defects or other AAR-approved procedure. The instrument sensitivity level should be adjusted to produce an approximate full-scale reflection from the reference
standards of paragraphs 18.4.3.2, 18.4.3.3, 18.4.3.4, and 18.4.3.5.

IMPLEMENTED 07/2009

18.4.3.2 For axial testing of all wheels, the reference standard shall be a 1/8-in.-diameter flat-bottom hole generated perpendicular to the rim face and to a depth of 1 1/2 in. (1/16 in.) at the
mid-thickness of the rim. See Fig. B.1
18.4.3.3 For radial testing, the reference standard shall be a 1/8-in.-diameter flat-bottom hole
generated from the inside diameter of the rim perpendicular to the tread surface, and shall be a
minimum of 1 1/4 in. from the tread surface. See Fig. B.2.
18.4.3.4 A distance amplitude correction (DAC) shall be used for axial and radial testing of
wheels. To ensure detection, the DAC will be generated for each testing direction in the following
manner.
Holes shall not be located close to each other so as to impede the response from each hole individually.
18.4.3.4.1 Axial
As a minimum, two additional 1/8-in.-diameter flat-bottom holes shall be generated at whatever
depth the manufacturer chooses. The creation of the DAC shall be accomplished using the reference standard and the response(s) from additional holes. Typical depths for the three holes could
be 1 1/2, 2 1/2, and 3 1/2 in. All holes should be generated from the front or back rim face. See
Fig. B.1. Individual depth standards shall be permitted.
18.4.3.4.2 Radial
To facilitate creation of a DAC, as a minimum, one additional 1/8-in.-diameter flat-bottom hole
shall be generated in one-wear and two-wear wheels, and, as a minimum, two additional
1/8-in.-diameter flat-bottom holes shall be generated in multi-wear wheels. Calibration shall be
accomplished using the reference standard, and the response(s) from the additional holes shall be
used to create the DAC. Table B.1 shows the depth of reference standard holes for the different
wheel types. See Fig. B.2. Individual depth standards shall be permitted.
18.4.3.5 Alternate calibration standards may be used when authorized by the AAR WABL Committee. Manufacturer shall document and demonstrate the correlation between the 1/8-in.-diameter flat-bottom hole and the proposed alternate standard.
18.4.3.6 An alternate method for axial testing of cast steel wheels is to use loss of back reflection.
The reference standard shall be a 3/8-in.-diameter concave bottom hole generated to a depth of
1/8 in. at the front rim face. See Fig. B.3.
18.4.3.7 Reference standards for the inspection of wheels shall be made from rim-treated wheel
steel made by the same process as the wheels being inspected, i.e., wrought or cast. Reference
standard need not be the same AAR design as the wheels being inspected.
18.4.3.8 Recalibration
Conduct ultrasonic calibration to ensure system conformance to required specifications. Check the
ultrasonic system and calibration of the instrument per documented procedures using a calibration standard when any of the following occurs:

11/1/04

Damage to any part of the ultrasonic system

Change in transducers, cables, and other accessories
Loss of power or equipment malfunction
Whenever ultrasonic instrumentation is first turned on

G [M-107/M-208] 11

11/1/04

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

18.4.3.9 System Verification and Test Results Validation

18.4.3.9.1 Conduct ultrasonic calibration checks to ensure system conformance to required specifications.
18.4.3.9.2 System calibration shall be verified per documented procedures using a calibration
standard at least every 8 hours of operation. If the results from system verification are outside of
system tolerance, assessment of previous inspections must be made and appropriate action taken.
Action taken shall be supported by wheel reinspection data.
18.4.3.9.3 Records shall be maintained of system calibration and system verification.
18.4.4 Scanning

18.4.4.2 One or more transducers shall be designed and located to give maximum volumetric coverage of the rim cross-section both radially and axially.
Each manufacturer shall ensure optimum volumetric coverage for the test method and manufacturing process. Optimization of coverage is verified by using supplemental reference standard
holes located in different areas of the rim, as shown in Figs. B.3.1 and B.3.2.
18.4.4.3 Scanning speed shall permit detection of reference standards at calibration level.
18.4.5 Rejection
18.4.5.1 Any wheel with a flaw indication equal to or larger than 25% of the reference standard
at the estimated discontinuity depth shall be cause for rejection.
18.4.5.2 Any indication from discontinuity giving a loss of back reflection equal to or greater than
the reference standard (covered in paragraph 18.4.3.6) during axial scanning shall be cause for
rejection.
18.4.5.3 Ultrasonic indications that result from wheel geometry or spurious electrical signals
shall not be valid cause for rejection.
18.4.5.4 The final disposition of rejectable wheel may be determined by manual testing of questioned areas. Wheel records and test results shall be maintained for wheels found to be conforming
under this paragraph.
18.5 Magnetic Particle Inspection
18.5.1 Purpose
To supplement visual inspection of the surface of new wheels by detecting discontinuities that may
be harmful to wheel service.
18.5.2 Scope
This test method covers the wet fluorescent magnetic particle inspection of the plates of wheels
ordered to this specification.

G [M-107/M-208] 12

11/1/04

IMPLEMENTED 07/2009

18.4.4.1 Wheels shall be inspected axially from either the front or back rim face and radially from
the tread surface.

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

18.5.3 Equipment

IMPLEMENTED 07/2009

18.5.3.1 Magnetizing Apparatus

The magnetizing apparatus shall be capable of inducing suitable magnetic fields within the entire
plate area of the wheel to facilitate the disclosure of both circumferentially and radially oriented
discontinuities. The magnetizing currents used shall be large enough to induce magnetic fields of
sufficient intensity to disclose surface discontinuities 1/4 in. long. The use of prod-type contacts is
prohibited.
18.5.3.2 Lighting Apparatus
The inspection shall be performed in a darkened booth with the area of the wheel to be inspected
illuminated with properly filtered black light. The black light shall have a predominant wavelength of 4000 to 3400 , and the intensity of the black light, measured at the surface to be
inspected, shall be a minimum of 75 footcandle at point of inspection.
18.5.3.3 Inspection Medium
18.5.3.3.1 The bath or solution should be prepared using a suitable carrier fluid and fluorescent
magnetic particles and renewed monthly or more often if contamination is noted in weekly tests.
Each time the bath is renewed, the bath container should be cleaned out and the agitation and circulation system should be flushed with 1 or 2 gal of clean carrier. Filtering screens should be
removed and cleaned by blowing with air. In preparing the new bath, only recommended materials
should be used. The amount of powder should be carefully weighed out in accordance with the
material manufacturers recommendation and be added directly to the bath containing the correct
amount of carrier. It is recommended that powder be added directly over the sump so that it will be
drawn quickly into the pump and circulated. The amount of carrier and powder used and the date
of preparation should be recorded on a regular form set up for this purpose, as outlined in
paragraph 18.5.3.3.6.
18.5.3.3.2 Concentration and contamination of the bath solution should be tested weekly as follows: pump and agitation system should be operated for 20 minutes and then the solution should
be run through a hose and nozzle for 30 seconds. Using a regular 100-mL centrifuge tube, fill the
centrifuge tube with 100 mL of the solution. Allow the bath solution to settle for the time recommended by the manufacturer of the type of powder used, making sure that the tube is not subjected to excessive vibration during the settling period. Each horizontal division represents
0.1 mL, and a correct reading in volume of particles must be as stipulated by the powder manufacturer. The check also should note contamination caused by dirt, chips, or other foreign matter settling with the powder. Contamination also is indicated when the carrier appears to acquire more
than usual fluorescence or when the magnetic particles appear to have lost fluorescent qualities.
This condition can be readily observed when the settling tube is exposed to ultraviolet light. The
readings obtained are to be shown on the regular report form as outlined in paragraph 18.5.3.3.6.
18.5.3.3.3 The ultraviolet light should be tested weekly using a light meter, such as a type having
75-footcandle scale with a 10 multiplying disc or equivalent or a meter that responds specifically
to the ultraviolet range of 3650 (365 nm). The latter type meters are calibrated in microwatts
per square centimeter. The meter should be held a fixed distance of 15 in. from the light source
(from the black light filter surface to the meter-sensing element) and should have a minimum
meter reading of 525 W/cm2.
18.5.3.3.4 The conversion factor from footcandles (for light meters) to microwatts per square centimeter is 5.7 times the footcandle reading (at 15 in. distance).
18.5.3.3.5 The maximum allowable footcandles will be left to the discretion of the user dependent
on the degree of brilliance desired to obtain satisfactory inspection conditions. Before taking readings, it should be known that the glass black light filters are clean. Reports of this test are to be
shown on regular form as outlined in paragraph 18.5.3.3.6.

11/1/04

G [M-107/M-208] 13

11/1/04

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

18.5.3.3.6 A regular form should be prepared embodying the information to be shown on monthly
and weekly tests as outlined above, and this form should be on hand at the wheel shop and available to AAR inspectors.
18.5.3.3.7 Prepackaged, self-contained solutions, including aerosol sprays, may be used provided
that the following conditions are met:
18.5.3.3.7.1 The solution is agitated frequently to ensure that magnetic particles remain in solution.

18.5.4 Preparation for Inspection

The surface shall be scale free before magnetic particle inspection.
18.5.5 Detection of Discontinuities
This inspection shall be performed to detect discontinuities whose axes may be in any direction.
Continuous or residual magnetization shall be used with adequate coverage by the inspection
medium.
18.5.6 Time of Inspection
The magnetic particle inspection shall be performed following final machining or grinding on wheel
plate.
18.5.7 Rejection
Rejection of magnetic particle discontinuity indications must take place if any plate surface indication is 1/4 in. in length or longer in any direction. Discontinuities may be removed by machining or
grinding where sufficient stock remains. Such wheels shall be retested by magnetic particle
inspection.
18.6 Personnel Requirements for Ultrasonic Inspection
18.6.1 All personnel engaged in ultrasonic operations will be qualified to NDT Level I according
to the qualification requirements as defined by the American Society for Nondestructive Testing,
Recommended Practice SNT-TC-1A, latest edition.
18.6.2 All personnel conducting inspection setups and machinery setups will be trained and qualified to meet the criteria for NDT Level II for ultrasonic testing as defined by the American Society
for Nondestructive Testing, Recommended Practice SNT-TC-1A, latest edition.
18.6.3 Each manufacturer will employ the services of an individual who will be trained and qualified to meet the criteria for NDT Level III for ultrasonic testing as defined by the American Society for Nondestructive Testing, Recommended Practice SNT-TC-1A, latest edition.
19.0 CERTIFICATION
At the purchasers request, a certification shall be made the basis of acceptance of the material.
This shall consist of a copy of the manufacturers test report that the material has been sampled,
tested, and inspected in accordance with the provisions of the specification. Each certificate so furnished shall be signed by an authorized agent of the supplier or manufacturer.

G [M-107/M-208] 14

11/1/04

IMPLEMENTED 07/2009

18.5.3.3.7.2 A detectability test is performed daily on each package in use and a record is kept
per paragraph 18.5.3.3.6. The test consists of inspection of a test wheel with a known crack of at
least 1/4 in. long or an equipment manufacturers approved test piece that will indicate and verify
the following:
Proper brilliance of ultraviolet light
Proper concentration of bath solutions
Proper magnetic power source and operation of equipment
Note: Test wheel or test piece must be thoroughly cleaned of the last test indicators before testing.
This must be verified by ultraviolet light before the test is started.

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

20.0 REJECTION
20.1 Wheels represented by samples that fail to conform to the requirements of these specifications will be rejected.
20.2 Wheels that show injurious defects subsequent to original inspection and acceptance at the
manufacturers works, or elsewhere, will be rejected, and the manufacturer shall be notified.

IMPLEMENTED 07/2009

21.0 REHEARING
Samples tested in accordance with this specification that represent rejected wheels shall be held
for a period of 14 days from date of the test report. In case of dissatisfaction with the results of the
tests, the manufacturer may make claim for a rehearing within that time.
22.0 This specification includes Appendices A and B; and Figs. B.1 through B.14.

11/1/04

G [M-107/M-208] 15

11/1/04

APPENDIX A

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

APPENDIX A
AUTHORIZATION FOR DELIVERY OF WHEELS FOR AAR INTERCHANGE
SERVICE
1.0 Each manufacturer must obtain an authorization for delivery of wheels for AAR interchange
use from the Committee prior to delivery.
2.0 The manufacturer applying for delivery authorization must provide the AAR with an
electronic copy of the following documentation. (Note: AAR prefers electronic submissions.
However, if an electronic copy is not provided, then manufacturer should provide 15 copies of the
printed documentation.)

2.1.1 A full-scale drawing showing the wheel cross-section from center of the hub to top of the
flange. The drawing may show either a single profile with tolerances or, preferably, two profiles,
with one depicting the minimum inner tolerances and the other the maximum outer tolerances in
such a way that a wheel section laid on the drawing would fall between the two profiles. This
would allow analysis of wheels produced to this drawing.
2.1.2 A notation of the wheel type and heat-treatment classes of the wheels to be produced.
2.2 A brief description of the design analysis method and the results of the analysis. The preferred analytic procedure is that covered in S-660. If there is no design analysis, a statement
should be made to this effect along with a summarization of the design considerations. If the applicant would like the AAR to perform the S-660 design analysis on a contract basis, the applicant
should request details from the AAR.
2.3 A statement advising the specific areas in which the wheel design may not be compatible with
normal shop machinery and handling equipment, standard storage facilities, and wheel transport
cars in general use.
3.0 Authorization for the delivery of a wheel type will be approved by the Committee if deemed
suitable for interchange service based on a review of wheel data submitted by the manufacturer.
The initial authorization will be for the delivery of 32,000 wheels. If the manufacturer requests
additional delivery authorizations, the second will be for 20,000 wheels (52,000 total) and the third
will be for 20,000 wheels (72,000 total). Additional allotments or unconditional approval for
unlimited quantities will be given after that, provided all required conditions are met.
3.1 A new wheel type (such as CH-36, CJ-36, or J-33) that is made for the first time by the
requesting manufacturer will require the following prior to being granted unconditional approval.
If necessary, WABL will designate a sponsor railroad to assist the manufacturer in meeting these
requirements.
3.1.1 A minimum of 5,000 wheels installed from the first allotment will have been tracked to
provide mileage and will have achieved 200,000 miles in service.
3.1.2 Ultrasonic testing to wheelshop requirements for turned wheels will be performed for 30 or
more wheels with at least 200,000 miles of service and with sufficient rim metal to be reapplied.
Provided all other criteria are met, upon successful completion of ultrasonic testing, conditional
approval, unlimited quantity will be granted. The 30 wheels will then be placed in service and
tracked. Ultrasonic testing to wheelshop requirements of turned wheels will be performed for 10 of
the 30 wheels reapplied after 100,000 miles additional service. Provided all other criteria are met,
upon successful completion of the ultrasonic testing, unconditional approval will be granted. Test
costs will be paid by the proponent, and data provided in the form of C-scans will be captured with
an AAR observer present and provided to WABL.

G [M-107/M-208] 16

11/1/04

IMPLEMENTED 07/2009

2.1 A descriptive drawing of the wheel type as it will be produced. The descriptive drawing will
provide the following information:

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

APPENDIX A

3.1.3 At least one out of every 1,000 wheels produced in the initial allotment will be tested for
microcleanliness according to paragraph 9.0 of this specification. Results will be reported to the
Wheels, Axles, Bearings, and Lubrication Committee Manager within 90 calendar days.
Electronic reporting is preferred. Send results to

IMPLEMENTED 07/2009

Email: [email protected]
Facsimile: 719-585-1895
Mail: AAR WABL Committee Manager
Transportation Technology Center Inc.
P.O. Box 11130
Pueblo, Colorado 81001
3.2 Each authorization after the initial authorization will be granted only after satisfactory
performance is indicated by a review of service data submitted on the wheel by the manufacturer
as well as service data from AAR records. Authorization may be withdrawn if service performance
so dictates.
4.0 Changes to any wheel design by the producer must be reviewed by the Committee before
delivery authorization may be granted.

11/1/04

G [M-107/M-208] 17

11/1/04

APPENDIX B

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

APPENDIX B
QUALIFICATION OF MANUFACTURERS PLANT AS A PRODUCER OF
WHEELS FOR AAR INTERCHANGE SERVICE
1.0 Applications for approval are to be submitted to the AAR. AAR prefers electronic
submissions. However, if an electronic copy is not provided, then applicant should provide 15
copies of the printed documentation. Applicants should provide a general description of the plant
and the equipment to be used in the production of wheels. In the event it is desired to deliver
mounted wheel sets, information indicating that equipment is available to comply with the wheel
mounting requirements of the AAR Manual of Standards and Recommended Practices, Section G,
Part II, Wheel and Axle Manual should be included.

3.0 Subsequent to the satisfactory completion of the tests and approval by the Committee of test
results, the AAR will inspect the plant where the wheels are to be produced for proper equipment
and, if mounted wheels are to be provided, an AAR inspection will be arranged for the wheel shop.
These inspections will require that all out-of-pocket expenses be borne by the applicant. These
inspections can be arranged concurrently with the test program if the applicant so requests.
4.0 All plants desiring to maintain their status as an AAR-approved manufacturer of wheels for
use in AAR interchange service must be inspected yearly with costs of inspection to be borne by
the wheel producer. Every effort will be made to inspect all plants in a given area at one time to
minimize costs, which will be prorated among the companies inspected.
5.0 In the event that a facility ceases production for less than 1 year and has not received its
scheduled annual inspection, an inspection of the facility is required prior to the delivery of any
items for use in interchange service. In the event a plant ceases production of wheels for AAR
interchange service for more than 60 days and less than 1 year, the AAR must be notified no later
than 2 weeks prior to reopening. In the event a plant ceases production of wheels for AAR
interchange service for more than 1 year, requalification will be required prior to delivery of any
items for use in AAR interchange service. An AAR inspection of the plant will be required, and
normally, the provisions of Appendix A will apply for all wheel designs that have been given an
authorization in accordance with the procedure outlined in paragraph 2.0 and subparagraphs. The
Committee may elect to require testing of wheels in accordance with Appendix B, paragraph 2.0.
6.0 In addition to the foregoing, wheel manufacturers must meet the requirements of the AAR
Manual of Standards and Recommended Practices, Section J, Specification M-1003, Specification
for Quality Assurance.
7.0 All plants desiring to maintain their status as an AAR-approved manufacturer of wheels for
use in AAR interchange service must also have their steel suppliers, shot peening, and
heat-treating subcontractors inspected if they do not use their own facility. These inspections will
be made in conjunction with the facility inspection, and the cost will be borne by the applicant.
8.0 Wheel manufacturers using a native language other than English are responsible for the
accurate communication of all applicable AAR and customer requirements within the plant.
8.1 Plant practices and the final product must conform to the English language versions of any
applicable standards or specifications.
8.2 Critical records are defined as the standards, internal procedures, and forms necessary to
demonstrate compliance with this Specification M-107/M-208 and with MSRP Section J, Specification M-1003. Critical records must be kept up to date with production and be maintained in
English.

G [M-107/M-208] 18

11/1/04

IMPLEMENTED 07/2009

2.0 After review of the data submitted with the application, the Committee will authorize the
applicant to contact the AAR for information concerning product testing. Normally this will consist
of the applicant furnishing three wheels, at applicants expense, for testing by the AAR. All costs
are to be paid by the applicant upon notification of the testing charges.

11/1/04

IMPLEMENTED 07/2009

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

Fig. B.1 Typical reference standard for rim face ultrasonic test
Paragraphs 18.4.3.2 and 18.4.3.4
Hole #1 reference hole
Holes #2 and #3 used for distance amplitude correction (DAC)

11/1/04

G [M-107/M-208] 19

APPENDIX B

11/1/04

APPENDIX B

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

IMPLEMENTED 07/2009

Fig. B.1.1 Axial rim test

Paragraphs 18.4.3.2 and 18.4.3.4
Alternate configuration for distance amplitude correction

G [M-107/M-208] 20

11/1/04

11/1/04

IMPLEMENTED 07/2009

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

APPENDIX B

Table B.1
Wheel Design
One-wear two holes
Two-wear two holes
Multi-wear three holes

Reference Hole #1
1 1/4 in.
1 1/4 in.
1 1/4 in.

Distance below Tread Surface

Hole #2
3/4 in.
3/4 in.
3/4 in.

Fig. B.2 Typical reference standard for rim tread ultrasonic test
Paragraphs 18.4.3.3 and 18.4.3.4
Hole #1 reference hole
Hole #2 and #3 used for distance amplitude correction (see Table B.1)

11/1/04

G [M-107/M-208] 21

Hole #3

2 1/4 in.

11/1/04

APPENDIX B

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

IMPLEMENTED 07/2009

Fig. B.3 Axial rim test

Paragraph 18.4.3.6

G [M-107/M-208] 22

11/1/04

11/1/04

IMPLEMENTED 07/2009

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

Fig. B.3.1 Tread rim test

Paragraph 18.4.4.2

11/1/04

G [M-107/M-208] 23

APPENDIX B

11/1/04

APPENDIX B

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

IMPLEMENTED 07/2009

Fig. B.3.2 Axial rim test

Paragraph 18.4.4.2

G [M-107/M-208] 24

11/1/04

11/1/04

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

APPENDIX B

MONTH
YEAR

SERIAL NUMBER

MFGR.

IMPLEMENTED 07/2009

CLASS

/8"

13/8"

1" MIN.

TAPE SIZE

Note 1

Note 2
Note 3
Note 4
Note 5

Stamping is to consist of manufacturers serial number, date of manufacture, manufacturers identification, and
class of heat treatment. Stamping is limited to 14 characters, and the design designation shall be stencilled on
the back plate with paint using characters at least 1 in. in height.
Stamping is to be spaced a minimum of 1/8 in. between characters and 1 3/8 in. between groups. The stamping
shall be located not less than 1/4 in. from the inner edge of the rim.
Dies used to produce characters shall be not less than 3/8 in. in nominal height at crest, and hot stamping shall
be nominally 3/32 in. in depth. Italicized characters (sloping upward to right) shall be used.
All wheels will be marked for class using letters L, A, B, or C, as appropriate.
All stamped characters must be stamped with a low-stress die design to a minimum depth of 0.015 in. or an
AAR-approved alternative.
Fig. B.4 Marking of locomotive wheels rim stamping
Paragraph 17.1

11/1/04

G [M-107/M-208] 25

12

77

GK

/"

38

1 3/8
"

MI

Note 2

Note 3

Note 4
Note 5
Note 6
Note 7

MIN
.
/18"

18

Note 1

89

SERIAL NUMBER

J33

54

N.

DESIGN

When ordered, locomotive wheels and wheels for passenger service may be ordered stamped on the front or
back hub face. Wheels for freight service are stamped on the back hub face.
Stamping is to consist of manufacturers serial number, date of manufacture, manufacturers identification, class
of heat treatment, and design designation in the order shown above. The hub stamping of locomotive wheels
may be applied by the purchaser after final machining of the hub. Wheels that are to be marked by the purchaser
should be furnished with all marking stencilled on the front plate with paint using characters at least 1 in. in height.
Stamping is to be spaced a minimum of 1/8 in. between characters and a minimum of 1 3/8 in. between groups
and located approximately central of the hub face. No wheel manufactured after May 1, 2009, may be bored and
applied with any portion of the wheel manufacturers hub stamp closer than 1/8 in. from the inner hub diameter
and no closer than 1/8 in. from the outer hub diameter. No wheel manufactured before May 1, 2009, may be
bored and applied with any portion of the wheel manufacturers hub stamp breaking over the edge of the inner
or outer hub diameter.
Stamps used to produce characters shall be not less than 3/8 in. in height and shall not have sharp edges.
All wheels will be marked for class using letters L, A, B, or C, as appropriate.
The three groups (1) design; (2) serial number; and (3) date of manufacture, manufacturer, and class will be
spaced approximately equidistantly around the hub face.
All stamped characters must be stamped with a low-stress die design to a minimum depth of 0.015 in. or an
AAR-approved alternative.
Fig. B.5 Marking of carbon steel wheels hub stamping
Paragraph 17.1

G [M-107/M-208] 26

11/1/04

IMPLEMENTED 07/2009

MONTH

/8"

CLASS

MFGR.

YEAR

M-107/M-208

160 TAPE SIZE

1' MIN.

/8"

11/1/04

APPENDIX B

AAR Manual of Standards and Recommended Practices

Wheels and Axles

11/1/04

IMPLEMENTED 07/2009

M-107/M-208

Manufacturers
Identification
TW
A
BV
BW
DW
P
ZW
QW
FW
EW
KW
LW
HW
MW
NW
RW
SW
JW
TY or TZ

AAR Manual of Standards and Recommended Practices

Wheels and Axles

Manufacturer
Adtranz
Armco
B.V.V. (Formerly VSG)
Bethlehem
Bonatrans a.s. (Formerly ZDB)
British Steel
Canadian Steel Wheel
Construcciones y Auxiliar de Ferrocarriles (CAF)
Creusot-Loire
Edgewater Steel LTD
Klockner
Lucchini Sidermeccanica SpA (Formerly Gruppo Lucchini)
Maanshan Iron and Steel Co. LTD
MWL (Formerly Mafersa)
Niznedneprovssky Tube Rolling Plant (NTRP)
S. C. SMR S.A (Formerly SMR/MECANO)
Standard Steel LLC
Sumitomo Metal Industries LTD
Taiyuan Heavy Industries Company LTD

Location
UK
Bochum, Germany

APPENDIX B

Cast or No Longer
Wrought in Production
W
X
W
X
W
W
X
W
W
X
W
X
W
W
X
W
X
W
X
W
W
W
W
W
W
W
W

Bohumin, Czech Republic

UK
Canada
Beasain, Spain
France
Oakmont, Pennsylvania
Germany
Lovere, Italy
Anhui, Province, P.R.C.
Cacapavz, Sao Paulo, Brazil
Dnepropetrovsk, Ukraine
Bals, Romania
Burnham, Pennsylvania
Osaka, Japan
Taiyuan, Shanxi Province,
(TY not used after 10/ 06)
PRC
CW
U.S. Steel
Pittsburg, Pennsylvania
W
G
U.S. Steel
Gary, Indiana
W
VW
Valdunes
Dunkerque &
W
Valenciennes, France
Nizhegorodsky Region, Russia
W
VK
Vyksa Steel Works
SO
ABC Rail (formerly Abex)
Calera, Alabama
C
C
Abex Rail **
Calera, Alabama
C
S
Abex **
St. Louis, Missouri
C
SJ
Abex
Johnstown, Pensylvania
C
T
Abex **
Toledo, Ohio
C
CZ
Amsted Maxion (Formerly Iochpe-maxion S.A.)
Cruzeiro, Brazil
C
Datong, Shanxi Province, China
C
CO
Datong ABC Castings Company LTD
FM
FM Fundiciones de Hierro y Acero
Mexico
C
GB
Griffin Wheel Company
Bensenville, Illinois
C
GC
Griffin Wheel Company
Columbus, Ohio
C
GI
Griffin Wheel Company
Kansas City, Kansas
C
GK
Griffin Wheel Company
Keokuk, Iowa
C
GL
Griffin Wheel Company
Colton, CA
C
GS
Griffin Wheel Company
Bessimer, Alabama
C
GT
Griffin Wheel Company
Winnipeg, Canada
C
GY
Griffin Wheel Company
St. Hyacinthe, Canada
C
Ruzhou, Henan Province, PRC
C
RZ
Tianrui Group Foundry Co. Ltd
C
WI
Rail Wheel Factory (Formerly Wheel and Axle Plant) Yelahanka, Bagalore, India
AW
Scaw Metals
Germiston, South Africa
C
** The letters C, S, or T directly precede the wheel serial number for wheels manufactured prior to about April 1978
Fig. B.6 AAR-approved manufacturers
11/1/04

G [M-107/M-208] 27

X
X

X
X
X
X
X

X
X

X
X
X

11/1/04

APPENDIX B

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

SERIAL NUMBER

09 7511
CJ-33

YEAR
MFGR.
CLASS

TRADEMARK
Note 1. Characters to be cast on the back plate of wheels shall, at least, show the manufacturers serial number, date of
manufacture, manufacturers identification, class, and design designation.
Note 2. Cast markings shall be legible characters, at least 1 in. high and so spaced to allow related characters to be readily
distinguished as a group.
Note 3 All wheels shall be marked for class using letters L, A, B, or C, as appropriate.
Note 4 The three groups (1) design; (2) serial number; and (3) date of manufacture, manufacturer, and class must be clearly
separate.
Fig. B.7 Raised markings on cast carbon steel wheels
Paragraph 17.1

G [M-107/M-208] 28

11/1/04

IMPLEMENTED 07/2009

78 S0 C
08

DESIGN

MONTH

11/1/04

IMPLEMENTED 07/2009

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

A
B
L
Pa/
R2
K
a/

Standard
Wide Flange
Dimensions and
Tolerances
1
1 + 16
0
1
1 38 + 32
3
32
5 2332 18
7 14
2 12 18
0.0865

APPENDIX B

Standard
Narrow Flange
Dimensions and
Tolerances
1
1 + 16
0
1
1 532 + 16
0
5 2332 18
(5 12 18 alternate)
See Note
See Note
0.0663

Except A-28 = 7 18

Fig. B.8 Standard dimensions and tolerances and permissible variations

Paragraphs 2.0 and 15.1
Note: For standard wheel types and for dimensions and other data not shown above, see Figs. B.9
through B.14.

11/1/04

G [M-107/M-208] 29

11/1/04

APPENDIX B

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

9.0 PERMISSIBLE VARIATIONS IN DIMENSIONS NOT SHOWN BY TOLERANCES ON

FIGS. B.9 THROUGH B.14
9.1 Inside DiameterFront Face of Rim
The inside diameter of the rim at the front face of the wheel shall not differ from that at the back
face of the wheel by more than 1/4 in.
9.2 Thickness of Rim
In any wheel, the radial thickness of the rim shall not vary more than 1/8 in. around the wheel.

9.4 Plane of Back Face

When wheels are gauged with a straight edge applied to the back face of the rim, no point on the
back face of narrow-flange wheels more than 1 1/4 in. from the inside edge of the rim shall be more
than 1/32 in. from the straight edge. For wide-flange wheels, no point on the back face of the rim
shall be more than 1/32 in. from the straight edge. For narrow- and wide-flange wheels, the back
face of the rim measured on the circumference at a distance 1 1/4 in. inward from the apex of the
flange must be in plane within 0.040 in. Total Indicator Reading (TIR) with respect to the plane of
the front face of the rim.
9.5 Hub Wall Thickness
The thickness of the hub wall in any one wheel measured at any two points equidistant from the
face of the hub shall not vary by more than 3/8 in. if the hub is not machined, nor by more than
1/8 in. if the hub is machined.
9.6 Rotundity
Tread when gauged with a ring gauge must not have an opening between tread and gauge at any
point over .022 in.
9.7 Diameter of Bore
The diameter of rough bore shall not vary more than 1/16 in. over nor more than 1/16 in. under the
dimensions specified by the purchaser.
9.8 Eccentricity of Bore
Eccentricity between the rough bore and tread, measured in the plane of the taping line, shall not
exceed .0625 in. TIR, except that no more than 5% of wheels delivered may be over .0625 in. TIR
and these must not exceed .09375 in. TIR.

G [M-107/M-208] 30

11/1/04

IMPLEMENTED 07/2009

9.3 Corner at Inside Diameter of Back Face

A sharp corner is preferable to facilitate measurement. In any case, the radius of the corner shall
not exceed 1/8 in.

AAR Manual of Standards and Recommended Practices

Wheels and Axles

11/1/04

M-107/M-208

APPENDIX B

L
TAPING
LINE

B
A
G

IMPLEMENTED 07/2009

N
R

O1

O2

P
C
L

STANDARD AAR WHEEL TYPESWIDE-FLANGE CONTOURFOR FREIGHT CAR SERVICECARBON STEEL

AAR
TYPE

A-28
CA-28

E-28
CA-28

A-30
CA-30

J-33
CJ-33

M-33
CM-33

P-33
CP-33

H-36
CH-36

J-36
CJ-36

K-36
CK-36

B-38
CB-38

C-38
CC-38

D-38
CD-38

STATUS
DATE

STND
1952

STND
1985

STND
1946

STND
1956

STND
1961

STND
1984

STND
1962

STND
1962

STND
1962

STND
1964

STND
1964

EFFECTIVE
DATE

1971

7/1/85

1971

1968

1968

3/1/85

10/1/72

1968

1968

9/1/73

1968

TREAD
TYPE

M-W

1-W

M-W

1-W

2-W

M-W

1-W

2-W

M-W

1-W

2-W

M-W

INTENDED
AXLE
CLASS

F, K

F, K

D, E

D, E

D, E, F, G

MAX. CAP.
PER WHEEL
(LB)

32,875

24,375

32,875

27,500

27,500

32,875

35,750

35,750

35,750

39,375

39,375

39,375

28 + 14
TAPES
(5%5)

28 + 14
TAPES
(5%5)

30 + 14
TAPES
(5%5)

33 + 14
TAPES
(5%5)

38 + 14
TAPES
(5%5)

38 + 14
TAPES
(5%5)

G (MIN)

21/2

11/2

21/2

N (MIN)

3/4

5/8

3/4

01

+1
111/80

+1
105/80

02

+1
111/80

MAX FINISH
BORE

DIMENSION AND TOLERANCESALL ENTRIES IN INCHES, EXCEPT TAPES

33 + 14
TAPES
(5%5)

33 + 14
TAPES
(5%5)

36 + 14
TAPES
(5%5)

36 + 14
TAPES
(5%5)

36 + 14
TAPES
(5%5)

38 + 14
TAPES
(5%5)

11/4

21/2

5/8

5/8

3/4

11/2

21/2

11/2

21/2

3/4

3/4

3/4

7/8

7/8

7/8

+1
111/80

+1
105/80

+1
105/80

+1
117/80

+1
111/80

+1
111/80

+1
111/80

+1
121/80

+1
121/80

+1
121/80

+1
105/80

+1
111/80

+1
105/80

+1
105/80

+1
117/80

+1
111/80

+1
111/80

+1
111/80

+1
121/80

+1
121/80

+1
121/80

87/8

83/8

87/8

83/8

83/8

95/8

87/8

87/8

87/8

95/8

95/8

95/8

MIN HUB
WALL

11/8

11/8

11/8

11/8

11/8

11/8

11/8

11/8

11/8

11/4

11/4

11/4

P1

71/8

71/4

71/4

71/4

71/4

71/4

71/4

71/4

71/4

71/4

71/4

71/4

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

21/2 1/8

NOTES:

1. HUB LENGTH TOLERANCE IS BASED ON FINISHED DIMENSION.

2. 5 1/2 10 AXLE ALSO STANDARD FOR J-33 AND M-33; 5 1/2 10, 6 11, AND 6 1/2 12 AXLES ALSO STANDARD FOR P-33

Fig. B.9 Standard AAR wheel typeswide-flange contourfor freight car service
Paragraphs 2.0, 15.1, and 15.2
11/1/04

G [M-107/M-208] 31

11/1/04

APPENDIX B

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

L
TAPING
LINE

B
A
G
N

IMPLEMENTED 07/2009

O1

O2

P
C
L

STANDARD AAR WHEEL TYPESNARROW-FLANGE CONTOURFOR DIESEL LOCOMOTIVE

AAR
TYPE

F-36
CF-36

A-38
CA-38

E-40
CE-40

A-41
CA-41

A-42
CA-42

A-43
CA-43

C-42
CC-42

D-42
CD-42

E-42
CE-42

STATUS
DATE

STND
1946

STND
1947

STND
1982

STND
1997

STND
1946

STND
1997

STND
1946

STND
1997

STND
1997

EFFECTIVE
DATE

8/1/46

1947

3/1/83

1997

8/1/46

1997

1947

1997

1997

TREAD
TYPE

M-W

M-W

M-W*

M-W*

M-W*

M-W*

M-W*

M-W

M-W

DIMENSION AND TOLERANCESALL ENTRIES IN INCHES, EXCEPT TAPES,

SEE Fig. B.8 FOR DIMENSIONS A, B, C, and L FOR ALL NARROW-FLANGE WHEEL TYPES
D

36"
TAPES
+ 14
0

38"
TAPES
+ 14
0

40"
TAPES
+ 14
0

41"
TAPES
+ 14
0

42"
TAPES
+ 14
0

43"
TAPES
+ 14
0

42"
TAPES
+ 14
0

42"
TAPES
+ 14
0

42"
TAPES
+ 14
0

G (MIN)

21/2

21/2

21/2

21/2

21/2

31/2

N (MIN)

3/4

7/8

121/2 1/8

+1
131/20

121/2 1/8

121/2 1/8

01

+1
130

+1
103/40

121/2 1/8

121/2 1/8

+1
111/20

02

+1
130

+1
103/40

131/4 1/8

131/4 1/8

+1
111/20

131/4 1/8

+1
131/20

131/4 1/8

131/4 1/8

61/2 1/8

71/8

61/2 1/8

61/2 1/8

71/8

61/2 1/8

61/2 1/8

61/2 1/8

61/2 1/8

R1

413/16 1/8

55/16 1/8

413/16 1/8

413/16 1/8

45/16 1/8

413/16 1/8

413/16 +1/8

413/16 1/8

413/16 1/8

R2

111/16 f

111/16 f

111/16 f

111/16 f

211/16 1/8

111/16 f

111/16 f

111/16 f

111/16 f

MAX FINISH
BORE

101/4

81/2

915/16

915/16

91/4

915/16

103/4

915/16

915/16

MIN HUB
WALL

13/8

11/8

**
11/8

11/8

11/8

11/8

13/8

11/8

11/8

NOTES:

1. WHERE DIMENSION R2 IS MARKED F, EXTRA STOCK OF 1/16 IN. TO 3/16 IN. OVER SPECIFIED DIMENSION MAY BE LEFT FOR MACHINING OF EACH FINISHED
SURFACE OR WHEEL MAY BE FURNISHED FINISHED TO EXACT DIMENSION SHOWN. HUB LENGTH TOLERANCE IS BASED ON FINISHED DIMENSION.

*
**

REFERENCE GROOVE REQUIREDSEE RP-619

HUB WALL THICKNESS MAY BE REDUCED AS NECESSARY FOR APPLICATION OF ROLLER BEARING WATER GUARD.

Fig. B.10 Standard wheel typesnarrow-flange contourfor locomotive service

Paragraphs 2.0, 15.1, and 15.2

G [M-107/M-208] 32

11/1/04

IMPLEMENTED 07/2009

M-107/M-208

AAR Manual of Standards and Recommended Practices

Wheels and Axles

APPENDIX B

AAR-1B WIDE PROFILE CENTERS OF

RADII RELATIVE TO GAUGE POINT
POINT
A
B
C
D
E
F

X
1.196896
0.589000
0.589000
0.362211
0.580300
1.060300

AAR-1B WIDE PROFILE INTERSECTION OF POINTS

RELATIVE TO GAUGE POINT
POINT
1
2
3
4
5
6
7
8
9

X
1.375000
1.147435
0.589000
0.091706
0.000000
0.035442
0.291159
0.631437
0.989517

Y
0.624585
0.031070
0.375400
0.162616
0.000000
0.132273
0.474998
0.624585
0.685529

Detail A
Fig. B.11 AAR-1B wide-flange contour for freight car wheels
Paragraphs 2.0, 15.1, and 16.2

11/1/04

G [M-107/M-208] 33

Y
1.149921
0.249600
0.312100
0.097100
0.007500
0.812800

AAR Manual of Standards and Recommended Practices

Wheels and Axles

APPENDIX B

M-107/M-208

IMPLEMENTED 07/2009

AAR-1B NARROW PROFILE CENTERS

OF RADII RELATIVE TO GAUGE POINT
POINT
A
B
C
D
E
F

X
0.204400
0.562500
0.562500
0.370581
0.571971
1.052000

Y
0.641800
0.312500
0.000000
0.065876
0.038692
0.844000

AAR-1B NARROW PROFILE INTERSECTION OF

POINTS RELATIVE TO GAUGE POINT
POINT
1
2
3
4
5
6
7
8
9

X
1.156300
0.853075
0.562500
0.140565
0.008400
0.028575
0.278542
0.748621
0.977100

Y
444011
0.237046
0.375000
0.230296
0.031335
0.106659
0.441210
0.625000
0.654129

Detail A
Fig. B.12 AAR-1B narrow-flange contour for freight car wheels
Paragraphs 2.0, 15.1, and 16.2

G [M-107/M-208] 34

11/1/04

AAR Manual of Standards and Recommended Practices

Wheels and Axles

M-107/M-208

APPENDIX B

51/2" 1/8"
15/32"
2"
CYLINDRICAL TREAD

+ 1/16"
- 0"

11/4"

/8"

111/16"
/32"

1"

/58"

/ "R

29 32

1 16

/8"

/"

11 16

/"

1 7/8
"R

1 2" R
23 /3

/"

5 8

/16"

IMPLEMENTED 07/2009

/58"

TAPER 1" IN 20"

+ 1/16"
- 0"

31

GAUGING POINT

/64"

TAPING LINE

VERTICAL
REFERENCE
LINE

NOTE: WHEN WHEEL RIMS ARE REDUCED IN THICKNESS TO SUCH AN EXTENT THAT LATHE DOGS INTERFERE WITH THE 5/8-IN. RADIUS AT THE OUTER RIM
FACE, THIS RADIUS MAY BE REDUCED AS NECESSARY OR A CHAMFER USED. FREIGHT LOCOMOTIVE WHEEL RIMS SHALL BE MACHINED WITH A
MAXIMUM RADIUS OF 5/8 IN. ON THE OUTER RIM FACE. A CHAMFER IS ALLOWED TO EXTEND PAST THE RADIUS AT 45, BUT MUST BE NO LONGER THAN
0.4375 IN. MEASURED ALONG ITS LENGTH.

Fig. B.13 Cylindrical tread contour for narrow-flange wheels

Paragraphs 2.0 and 16.2

11/1/04

G [M-107/M-208] 35

AAR Manual of Standards and Recommended Practices

Wheels and Axles

APPENDIX B

M-107/M-208

6.500
3

"

1.469

"

R1.500
1.094

BASELINE
1

CENTERS OF RADII
A (0.000, 0.000)
B 0.480, -0.8053)

2.8624

IMPLEMENTED 07/2009

INTERSECTION POINTS
1 (0.0841873, -1.49764)
2 (0.4289, -1.4374)
3 (0.769141, -1.2878)
4 (1.02338, -0.950724)
5 (1.0603, -0.8128)

4.000
A
WHEEL CONTOUR ACCEPTANCE GAUGE
FOR AAR 1B NARROW & WIDE FLANGE

R.5625
1.987

VERIFY WITH CONTOUR MAPPING

MAX MANUFACTURE DEVIATION: .003"
MAX RECERTIFICATION DEVIATION: .005"

MATERIAL:
STAINLESS STEEL 17-7
1
8 " THICKNESS
HARDENED

.750

Fig. B.14 Tread contour gauge for AAR-1B wheels

Paragraph 16.5

G [M-107/M-208] 36

11/1/04