0% found this document useful (0 votes)
836 views1 page

How To Disable Auto Configuration IPv4 Address

The document provides instructions for disabling autoconfiguration of IPv4 addresses on a Windows server virtual machine connected to a host computer via bridge mode. Specifically, it describes running commands to [1] view network interface information and identify the interface number, [2] set that interface to not transmit duplicate address detection packets, and [3] disable the DHCP client service. Disabling autoconfiguration prevents the virtual machine from obtaining conflicting IP addresses that can cause internet connection issues.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
836 views1 page

How To Disable Auto Configuration IPv4 Address

The document provides instructions for disabling autoconfiguration of IPv4 addresses on a Windows server virtual machine connected to a host computer via bridge mode. Specifically, it describes running commands to [1] view network interface information and identify the interface number, [2] set that interface to not transmit duplicate address detection packets, and [3] disable the DHCP client service. Disabling autoconfiguration prevents the virtual machine from obtaining conflicting IP addresses that can cause internet connection issues.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Notebook for Programming: How to disable Autoconfiguration IPv...

1 of 1

http://lyngtinh.blogspot.com/2011/12/how-to-disable-autoconfigura...

How to disable Autoconfiguration IPv4 Address


Sometime you setup windows server 2008 to vmware using LAN or wifi, you chose Bridge mode to share internet connections
between host and virtual machine may be cause of issues with internet connection at virtual machine. They can not connect to the
internet or appear a message likes "conflict IP address"
Enter: Run > cmd > ipconfig /all
You may see the following issues:

or:
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Intel(R) 82567LM-3 Gigabit Network Connection
Physical Address. . . . . . . . . : 00-23-24-08-30-57
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::8508:6cb9:5112:f8c9 (Preferred)
Autoconfiguration IPv4 Address. . : 169.254.248.201(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
IPv4 Address. . . . . . . . . . . : 192.168.1.136(Duplicate)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.1.1
NetBIOS over Tcpip. . . . . . . . : Enabled
To fix it, enter these from Command Prompt:
C:\Users\lyngtinh> netsh interface ipv4 show inter
result as:
Idx Met MTU State Name
--- ---------- ---------- ------------ --------------------------1 50 4294967295 connected Loopback Pseudo-Interface 1
11 10 1500 connected Local Area Connection
11: <=Keep it in mind
Next run this command:
C:\Users\lyngtinh>netsh interface ipv4 set interface 11 dadtransmits=0 store=persistent
Next, enter
Run > services.msc > disable DHCP Client service
Final, restart your server.

5/16/2014 5:17 PM

You might also like