0% found this document useful (1 vote)
1K views7 pages

Handle (Joystick) - Remove and Install

This document provides instructions for removing and installing the handle (joystick) on a 315C Excavator. The removal procedure involves removing covers and screws to access the joystick harness assemblies and locknut. The handle is then lifted from the boot and unscrewed. Installation follows the removal steps in reverse, reconnecting harnesses and securing the handle with the locknut.

Uploaded by

mekanicobucaro
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (1 vote)
1K views7 pages

Handle (Joystick) - Remove and Install

This document provides instructions for removing and installing the handle (joystick) on a 315C Excavator. The removal procedure involves removing covers and screws to access the joystick harness assemblies and locknut. The handle is then lifted from the boot and unscrewed. Installation follows the removal steps in reverse, reconnecting harnesses and securing the handle with the locknut.

Uploaded by

mekanicobucaro
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Cerrar SIS

Pantalla anterior
Producto: EXCAVATOR
Modelo: 315C EXCAVATOR CFB
Configuracin: 315C & 315C L Excavators CFB00001 -UP (MACHINE)
POWERED BY 3046 Engine

Desarmado y Armado
315C Excavator Machine Systems
Nmero de medio -RENR5525-05

Fecha de publicacin -01/11/2008

Fecha de actualizacin -10/11/2008


i01929067

Handle (Joystick) - Remove and Install


SMCS - 5705-010

Removal Procedure

Illustration 1

g00739085

1. Remove the cover from the front of the console. Remove screws (1) .

Illustration 2

g00739101

2. Remove screws (2) from the rear of the console.

Illustration 3

g00739106

3. Open armrest (3). Remove screws (4) and armrest (3) .

Illustration 4

g00739111

4. Reposition cover (6) in order to access harness assemblies (5) on the right hand console.
Disconnect harness assemblies (5) .
5. Remove cover (6) from the console.

Illustration 5

g00739116

6. Disconnect harness assemblies (7) from the joystick.

Illustration 6

g00739127

7. Lift rubber boot (8) over handle (9) .


Note: Mark the location of locknut (10) and the handle for installation procedures.
8. Hold nut (11). Loosen locknut (10). Unscrew handle (9) in order to remove the handle.
9. Remove rubber boot (8) from the handle.

Installation Procedure

Illustration 7

g00739127

1. Install rubber boot (8) on the handle.


2. Install handle (9) in nut (11) to the original position. Hold nut (11). Tighten locknut (10) to a
torque of 49 3 Nm (36 2 lb ft).

Illustration 8

g00739116

3. Connect harness assemblies (7) to the joystick.

Illustration 9

g00739111

4. Place cover (6) over the joystick, as shown.


5. Connect harness assemblies (5) .

Illustration 10

g00739106

6. Install armrest (3) and screws (4) .

Illustration 11

g00739101

7. Install screws (2) to the rear of the console.

Illustration 12

g00739085

8. Install screws (1) and the cover.

Copyright 1993 - 2010 Caterpillar Inc.


Todos los derechos reservados.
Red privada para licenciados del SIS.

Thu Sep 30 21:27:04 EST 2010

You might also like