Additional API 571 Practice Questions Flashcards - Quizlet

4/2/2016
AdditionalAPI571PracticeQuestionsflashcards|Quizlet
Additional API 571 Practice Questions

12 terms by Jmehatt
Like this study set? Create a free account to save it.
Create a free account
What type mechanical testing can

confirm temper embrittlement and
what is the main
type of failure mode?
a
4.2.3.5
a) It may be confirmed by impact

testing and may result in catastrophic
brittle fracture
b) It can only be confirmed through
metallographic examination and may
result in brittle fracture
c) It may be confirmed by tensile
testing and may result long term creep
failure
d) It can be confirmed by 100%
radiography and may result in long
term creep failure
https://quizlet.com/74314379/additionalapi571practicequestionsflashcards/
1/4
4/2/2016
Most cases of sigma phase

embrittlement are found in the form of
______ during startup or shutdown
when the material is below about
500oF (260C):
a) cracking in both wrought and cast
(welded) metals
b) coalesced chromium carbides that
may or may not be found with NDE
techniques
c) chromium carbide precipitation that
can be found with metallographic
examination
d) all forms of carbide precipitation that
can be found with metallographic
examination
a
4.2.6.5 b)
Carbon steels, low alloy steels, and 400

series stainless steels are of prime
concern for:
a) 885F embrittlement
b) Sigma phase embrittlement
c) a and b
d) Brittle fracture
d
4.2.7.2
To prevent stress ruptures:

a) minimize localized temperature
excursions.
b) utilize burners which produce a
more diffuse flame pattern.
c) maintain refractory in serviceable
condition in refractory lined
equipment.
d) all of the above.
d
4.2.10.6 a) c) e)
2/4
4/2/2016
Dissimilar metal weld cracking typically:

a) forms at the toe of the weld in the
heat-affected zone of the ferritic
material
b) occurs in welds joining tubes
c) occurs in support lugs or
attachments of cast or wrought 300
Series SS to 400 Series ss
d) all of the above
d
4.2.12.5 a) b)
In fired heater tubes, inspection of

dissimilar metal weld cracking can be
performed by:
a) visual, MT and PT inspect ion
b) MT and PT inspection
c) visual inspect ion only
d) None of the a bove
a
4.2.12.7 a)
Erosion-corrosion occurs when

corrosion contributes to erosion by:
a) removing protective films or scales
b) removing protective films or scales
and exposmg the metal surface to
aqueous corrosion under the
combined action of er osion and
corrosion
c) exposing the metal surface to
aqueous corrosion under the
combined action of erosion and
corrosion
d) accelerating th e anode-cath ode
potential
a
4.2.14.1 b)
Inspection techniques that can be used

to detect fatigue cracks at known areas
of stress concentration a re:
a) PT, MT and SWUT
b) PT and MT
c) VT and WFMT
d) UT and RT
a
4.2.16.7 a)
3/4
4/2/2016
In many cases, reheat cracks are

confined to:
a) weld h eat affected zone and some
type of stress concentration location
b) fine intergr anular precipitation sites
c) fine intergranular precipitation sites
in aqueous corrosion environments
d) all of the above
a
4.2.19.3 c)
Joint configurations in heavy wall

sections that are not designed to
minimize restraint during welding and
PWHT are prone to:
a) fatigue cracking during fabrication ,
including PWHT
b) thermal fatigue cracking during
service
c) reheat cracking during PWHT or in
service at elevated temperatures
d) HIC during PWHT
c
4.2.19.3 d)
4.2.19.6 a)
Corrosion of piping, pressure vessels

and structural components resulting
from water trapped under insulation or
fireproofing are most likely to occur in:
a) carbon steel and coated low alloy
steels
b) 300 Series SS and duplex stainless
steels
c) nickel and titanium alloys
d) tantalum alloys
b
4.3.3.2
The most important variables that

affect and differentiate the various
forms of wet H2S damage are:
a) environmental conditions (PH, H2S
level, contaminants, temperature)
b) material properties (hardness,
microstructure, strength
c) tensile stress level (applied or
residual)
d) all of the above
d
5.1.2.3.3 a)
4/4

Additional API 571 Practice Questions Flashcards - Quizlet

Uploaded by

Copyright:

Available Formats

Additional API 571 Practice Questions Flashcards - Quizlet

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Additional API 571 Practice Questions Flashcards - Quizlet

Uploaded by

Copyright:

Available Formats

What type mechanical testing can confirm temper embrittlement and what is the main type of failure mode?

What type mechanical testing can confirm temper embrittlement and what is the main type of failure mode?

What are the prime concerns for sigma phase embrittlement?

What are the prime concerns for sigma phase embrittlement?

4/2/2016

Additional API 571 Practice Questions

Like this study set? Create a free account to save it.

Create a free account

What type mechanical testing can

a) It may be confirmed by impact

Most cases of sigma phase

Carbon steels, low alloy steels, and 400

To prevent stress ruptures:

Dissimilar metal weld cracking typically:

In fired heater tubes, inspection of

Erosion-corrosion occurs when

Inspection techniques that can be used

In many cases, reheat cracks are

Joint configurations in heavy wall

Corrosion of piping, pressure vessels

The most important variables that

You might also like