Scribd
Upload
67 views2 pages

Porosity of Soil

This document outlines a procedure to determine the porosity of a soil sample. It involves measuring both the solid density and bulk density of the soil. Solid density is found by weighing a pycnometer filled with water and soil, then calculating density based on displacement. Bulk density is measured by taking soil cores of a known volume using a cylindrical cutter, then weighing the cores to find density. Porosity is calculated as 1 minus the ratio of bulk density to solid density.

Uploaded by

Ramesh Konakalla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
67 views2 pages

Porosity of Soil

This document outlines a procedure to determine the porosity of a soil sample. It involves measuring both the solid density and bulk density of the soil. Solid density is found by weighing a pycnometer filled with water and soil, then calculating density based on displacement. Bulk density is measured by taking soil cores of a known volume using a cylindrical cutter, then weighing the cores to find density. Porosity is calculated as 1 minus the ratio of bulk density to solid density.

Uploaded by

Ramesh Konakalla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

DETERMINATION OF SOIL POROSITY

AIM: To determine the porosity of given soil sample.


APPARATUS: Cylindrical core cutter, Dolley, Rammer, Balance (1 g accuracy), Spade,
Straight edge knife, Sample extruder, Apparatus for moisture content determination,
Pycnometer.

PROCEDURE:
Determination of porosity of soil requires determination of Solid density and Bulk density of
soil.

Determination of Solid Density:


1. Weigh a pycnometer flask with glass stopper and record the weight (W1).
2. Fill the flask about one-third with air-dry soil. Weigh the flask, stopper and soil.
Record the combined weight as (W2).
3. Add water to the soil slowly, mixing soil and water thoroughly by vigorous shaking
until the flask is full. Allow the air bubbles to rise to the surface. Float foam out of the
flask by adding a few more drops of water. Insert stopper, wipe the outside dry, weigh
and record as (W3).
4. Pour out entire contents into waste bucket and rinse flask. Then refill the flask with
water only, stopper, wipe the outside dry, weigh and record as (W4).

Determination of Bulk Density:


1. Measure the internal dimensions of the core cutter and weigh it.
2. Clean and level the site surface where the field density is to be determined.
3. Place the dolley on the cutter and press both into the soil using the rammer until
only about 15 mm of the dolley protrudes above the surrounding soil surface.
4. Remove the soil around the cutter with the spade, lift up the cutter, and trim
carefully the top and bottom surfaces of the soil sample.
5. Clean the outside surface of the cutter and weigh it with the soil.
6. Remove the soil core from the cutter and take three representative samples in
moisture cans for water content determination.

OBSERVATIONS AND CALCULATIONS:


Test temperature (C) =
Test No.
Pycnometer / Density bottle No.
Mass of pycnometer, W1 (g)
Mass of pycnometer + dry soil, W2 (g)
Mass of pycnometer + soil + water, W3 (g)
Mass of pycnometer + water, W4 (g)
Solid Density of soil (s) =

w*(W2 W1)

(W4 W3) (W1 W2)

Bulk Density:
Internal diameter of core cutter (cm) =
Height of cutter
(cm) =
Volume of cutter, V
(cm3) =
Field Test No.
Mass of core cutter (g), W1

Mass of cutter + soil (g), W2


Mass of moist soil (g), (W2- W1)
Average water content, w (%)

Field bulk density (g/cm3),


In-situ density = Average of the computed values =
Porosity is given by (n) = [1- (Bulk Density/ Solid Density)] = [1-(t/

RESULT: Porosity of given soil is ____________.

s)] =

You might also like