Activity 3.

2 Unit Conversion
Introduction
Engineers of all disciplines are constantly required to work with measurements of a
variety of quantities length, area, volume, mass, force, time, temperature, electric
current, etc. It is often necessary to be able to express those measurements in
different units. For example, when designing a water distribution piping system, it is
important to know how much water pressure is lost as the fluid flows through the
pipe. The pressure loss depends on the length of the pipe which is often measured
in miles. One formula that is sometimes used to calculate pressure loss requires that
the pipe length be input in feet. Therefore, it is necessary to be able to convert miles
to feet.
In other situations you may be forced to work between the SI and U S Customary
measurement systems. Say, for example, that as a U S company, your product is
manufactured and produced based on U S Customary units. However, a European
company would like a proposal to incorporate your system into their existing
assembly line, the characteristics of which are based on SI units. You must be able
to convert between the two systems in order to provide a proposal for a design
which includes your companys U S product.
In this activity you will convert measurements among units in both the U S
Customary System and the SI system, and you will convert quantities between the
two systems of measurement. You will also gain experience with converting units
among units that are not specific to one measurement system (such as people and
tanks of water) and use the skills you learn to solve everyday problems (such as
calculating the cost of gas to travel a given distance).

Equipment

Engineering notebook
Pencil
Ruler U S Customary and metric
Tape measure
PLTW Engineering Formula Sheet

Procedure
Complete each of the following. When a calculation is required, show your work.

2012 Project Lead The Way, Inc.

Introduction to Engineering Design Activity 3.2 Unit Conversion Page 1

1.

Write an equation that shows the equivalency between meters and Gigameters.

X m * 10^9 =X Gm
2.

What conversion factor should be used to convert from meters to Gigameters?

*10^9
3.
Convert each of the following quantities to the indicated units. Use the
appropriate number of significant figures to express your answer unless directed
otherwise.
a. 4.567 trillion (4,567,000,000,000) meters to Gigameters.
4,567,000,000,000 * 10^-9 = 4567
4,467 Gm
b. 14520 milliliters to liters. Report to the nearest hundredth of a liter.
14,520 ml * 10^-3 = 14.52
c. 43 thousand microseconds to seconds. Report to the nearest thousandth of a
second.
43,000 * 10^-6 = 0.043 seconds
d. 6.30 yards to feet.
6.3 * 3 = 18.9 ft
e. 0.55 feet to inches.
0.55 * 12 =6.6 inches
f. 9 ft 2 in. to inches. Report answer using fractional inches.
9*12 + 2 = 110 in
g. 3 ft 5 inches to decimal feet. Report to the nearest hundredth of a foot.
5/12 in =.42 ft

3.42 ft

h. 59.2 cm to inches. 59.2/2.54 = 23.30 in

i. 3.20 yards to inches. 3.2 *3 = 9.6 ft,

9.6 * 12 = 115.2 in

2012 Project Lead The Way, Inc.

Introduction to Engineering Design Activity 3.2 Unit Conversion Page 2

j. 350,000,000,000 nanoliters to decaliters.

decaliters

350,000,000,000 * 10^-10 = 35

4. A village on a Caribbean island was devastated by a hurricane. The supply of

fresh water was contaminated when the storm surge washed over the island,
inundating the wells. Several tanks of fresh water were delivered to the village. Each
tank contains 10.5 hectoliters of water.
a. How many liters of water does each tank contain?
10.5 * 10^2 = 1050 li
b. On any given day, one person needs an average of 2.5 liters of water to
survive. How many people will a tank supply for the day? Hint: Create a
conversion factor to convert from liters to people.
1050/2.5 = 420 people
c. If the village (which includes people and livestock) requires a total of 430 liters
of water each day, approximately how long (in days) will one tank provide an
adequate supply for the village? Give your answer to the nearest tenth of a
day. Hint: Create a conversion factor to convert form liters to days.
1050/430 =2.4
[Challenge] Convert the result to days and hours. Give your answer to the
nearest hour.
0.4 * 24 =9.6, 2days 10 hours
5. It is 3.67 miles to your grandparents home.
a. If you can walk 4 miles in one hour, how long will it take for you to walk to
your grandparents home? Express your answer in decimal hours and then
convert the time to minutes (to the nearest minute). 3.67/4=0.9175, 0.9175
*60 + 55.05
Hours: 0.9175 hour

Minutes: 55 min
b. If your average stride length is 2.6 feet, how many strides will it take you to
walk to your grandparents home? Hint: You will need two conversion factors.
1mi= 5280ft*4=21120ft/2.6 = 8123 strides
2012 Project Lead The Way, Inc.
Introduction to Engineering Design Activity 3.2 Unit Conversion Page 3

c. If you ride your bike at an average speed of 15 mph, how long will it take you
to ride to your grandparents home? Express your answer in hours (to the
nearest hundredth of an hour). Convert to minutes (to the nearest minute).
4/15 * 1 hour= 0.25 hours = 15 min

d. If the circumference of each wheel on your bicycle is 82.6 inches, how many
revolutions of a bicycle wheel will it take to get to your grandparents home?
Give your answer to the nearest revolution. Hint: You need to convert miles to
inches and create a conversion factor to convert inches to revolutions of a
wheel. 5280feet per mile * 12 = 63360 inch. 63360/ 82.6 = 767.1

6. Measure the size of your desk (length, width, and height) using a tape measure.
Record the measurement in feet and inches, and then convert the measurements to
decimal feet and decimal inches.
Measurement

Feet-inches

Decimal feet

Decimal inches

width

2 ft - 6 in

2.5 ft

30 in

height

2 ft 6.4 in

2.54 ft

29.5 in

depth

6 ft

6 ft

96 in

2012 Project Lead The Way, Inc.

Introduction to Engineering Design Activity 3.2 Unit Conversion Page 4

7. Measure and record additional items in your classroom and then convert each
measurement to an alternate unit as directed by your instructor.
Object

Description of
Measurement

room

Original
Measurement

Original
Measurement
Units

Converted
Measurement

Converted
Measurement
Units

ft-in.

7.77 x 9.15

in.

11.7475

cm

length x width 25-6 x 30-0

CD

diameter

4 5/8

2016
robotics
bumper

Width* height

5 *4

ft-in

17.8*121.92

cm

FRC
Battery

Width* Height

7* 7

in

17.78*17.78

cm

FTC game
cube

Width* depth*
height

2*2*2

in

5.08*5.08*5.08

cm

Gladiator
cabinet

Height *width

28*28

in

71.12*71.12

cm

8. Many track and field events are measured in metric units.

a. In the long jump, if you can jump 5.92 meters, what is your jump length in
feet? In yards?
592 cm = 233.071 in/12=19.42ft /3 = 6.47 yards

b. How many yards must you run to complete a 100 meter dash?
100 m * 1.09361= 109.361 yards
c. The womens world record high jump is 6 feet, 10 inches. What is the
record in meters? Record your answer to the nearest hundredth of a meter.
6 feet + 10 in= 82 in= 208.915cm= 2.09 m

d. How many meters is equivalent to a mile? Give your answer to the nearest
meter.
1 mile = 5280 feet, 1 meter = 3.28 ft, 5280/3.28 = 1610 meters per mile

2012 Project Lead The Way, Inc.

Introduction to Engineering Design Activity 3.2 Unit Conversion Page 5

e. What is the length of a marathon (26.2 miles) in kilometers? 26.2 * 1610 =

42182 meters = 42.182 Km
9. A European car manufacturer reports that the fuel efficiency of the new MicroCar is
28.5 km/L highway and 22.0 km/L city. What are the equivalent fuel efficiency rates
in miles per gal?
3.78541liters = 1 gal. 1 liter = 0.264 gal
22 kilometer = 22,000 meters* 3.28= 72160 ft/ 5280 = 13 2/3 mile * 3.7854= 51.7338
51.7 miles/gal

If gas costs $3.50 per gal, how much would it cost to drive 500 miles in the city in
this car (assuming the fuel efficiency rating is accurate)?
500/ 51.7= 9.7, 9.7* $3.50= $33.95 per 500 mi city

Conclusion
1 Why would you have to know how to convert measurements when looking at
a technical drawing?
Some drawing may be in standard or metric and you may need to convert them

2 How can you use units help you solve a problem?

If you need to measure something to fit something another object the
measurements have to be precise

2012 Project Lead The Way, Inc.

Introduction to Engineering Design Activity 3.2 Unit Conversion Page 6