Installation Guide

EMC Data Domain DD9500 System

Installation and Setup Guide
302-001-641
REV. 02

October 2015
This document provides installation and the setup instructions for the rack brackets,
shelves, and the DD9500 system.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l

Revision history......................................................................................................... 2
Related documentation..............................................................................................2
Tools and supplies needed........................................................................................ 3
Safety information..................................................................................................... 3
Description of the system...........................................................................................5
Define the Data Domain system information for your site......................................... 12
Unpack the system.................................................................................................. 13
Install the rack brackets........................................................................................... 14
Install the DD9500 system into a rack...................................................................... 23
Mount the cable management assembly.................................................................. 26
Installing the expansion shelves into the racks........................................................ 30
Connecting the expansion shelves and the controller...............................................31
Install the bezel....................................................................................................... 47
Connect data cables................................................................................................ 48
Power on all systems............................................................................................... 48
Enable administrative communication..................................................................... 48
Accepting the End User License Agreement (EULA)................................................... 50
Run the configuration wizard....................................................................................50

Installation Guide

Revision history
Table 1 Document revision history

Revision Date

Document part
number/Revision
number

Software
version

Description

02

October
2015

302-001-641 REV 02 5.7

Supporting DS60 shelves

01

April 2015

302-001-641 REV 01 5.6

Initial publication

Related documentation
EMC provides a variety of document types to support our products. End-user documents
include user guides, hardware installation guides, administrator guides, software guides,
part replacement guides, release notes, and others. Integration documents describe how
to integrate Data Domain systems with third party backup applications, and compatibility
matrices show which components are compatible with each other.
This document refers to other EMC documents by title. To locate a referenced document,
go to the EMC Support website at https://support.emc.com, enter the document title in
the search box, and click the search button.
Note

Hard copies of a document may be out of date. Always check for the current version of a
document before you start an upgrade or begin a significant configuration change.

Viewing Data Domain documents

Procedure
1. Log into the EMC Online support site at: https://support.emc.com.
2. To view user documents, click Product Documentation and then perform the following
steps:
a. Select the Data Domain model from the Platform list and click View.
b. On the row for the correct Data Domain operating system (DD OS) version, click
View under Documentation.
c. Click the desired title.
3. To view integration-related documents, perform the following steps:
a. Click Integration Documentation.
b. Select the vendor from the Vendor dropdown list.
c. Select the desired title from the list.
4. To view compatibility matrices, perform the following steps:
a. Click Compatibility Matrices.
b. Select the desired title from the Current Releases list.
2

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Where to go for more information

For information about:

Go to https://support.emc.com/

How to configure the system

EMC Data Domain Operating System Initial

Configuration Guide

New features, enhancements, known issues, EMC Data Domain Operating System Release Notes
and late-breaking news about your Data
for your software release
Domain software release
How to manage the Data Domain operating
system

EMC Data Domain Operating System

Administration Guide for your software release

How to install and use the DD Boost

software and plug-in

EMC Data Domain Boost for OpenStorage

Administration Guide for your software release

How to replace Data Domain hardware

components

Specific part installation guides

How to use third-party applications

Integration documentation and compatibility

matrices

Tools and supplies needed

For a list of recommended tools and supplies for field work, see the document titled FE
Toolkit Inventory and Common Procedures for FRU Tasks at https://support.emc.com.

Safety information
CAUTION
l

If the system is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.

The RJ45 sockets on the motherboard, PCI cards, or I/O modules are for Ethernet
connection only and must not be connected to a telecommunications network.

Review this list of important safety recommendations.

l

All plug-in modules and blank plates are part of the fire enclosure and must be
removed only when a replacement can be added immediately. The system must not
be run without all parts in place.

A DD9500 system must be operated only from a power supply input voltage range of
200240 VAC and 5060 Hz. The ES30 shelves use 100-240 VAC and 5060 Hz.

Each component is intended to operate with all working power supplies installed.

Provide a suitable power source with electrical overload protection.

A safe electrical earth connection must be provided to each power cord. Check the
grounding of the power sources before applying power.

The plug on each power supply cord is used as the main device to disconnect power
from the system. Ensure that the socket outlets are located near the equipment and
are easily accessible.
Where to go for more information

Installation Guide

Permanently unplug the unit if you think it is damaged in any way and before moving
the system. A DD9500 system includes four power supplies. To completely remove
system power, you must disconnect all four power supplies.

The power connections must always be disconnected prior to removal or replacement

of a power supply module from any of the components in the system.

A faulty power supply module must be replaced within 24 hours.

Do not lift system components by yourself. A DD9500 system weighs up to 117 lbs
(53.2 kg) and an ES30 expansion shelf weighs up to 68 lbs (30.8 kg).
CAUTION

EMC Data Domain systems are heavy. Use at least two people or a mechanical lift to
move any system.
l

Do not lift an expansion shelf by the handles on any modules. The handles are not
designed to support the weight of the populated shelf.

To comply with applicable safety, emission, and thermal requirements, covers must
not be removed and all bays must be fitted with plug-in modules.

Once removed from the shipping box, it is ok to lift the DD9500 system or the chassis
with the four handles to place in a rack. You will need to remove the handles from the
sides before sliding the system in the rack. The four handles should be saved for later
use.
Figure 1 Warning about lifting the system

Load the rack with storage shelves beginning at the bottom and the DD9500 system
in the designated location to prevent the rack from becoming top-heavy.

For ESD protection, EMC Data Domain recommends that you wear a suitable antistatic
wrist or ankle strap. Observe all conventional ESD precautions when handling plug-in
modules and components.

Do not extend components on slide rails until you have loaded at least three or more
similarly weighted items in the rack, or unless the rack is bolted to the floor or
overhead structure to prevent tipping.

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Description of the system

This section includes site requirements, product specifications, and descriptions of front
and rear panels.

Site requirements
Site requirements are described below.
l

The controller requires 4U of vertical space in a rack. The ES30 expansion shelf
requires 3U. Use a standard 19, four post rack. Do not use a two-post rack.

Use air conditioning that can cope with the maximum BTU/hr thermal rating.

Use adequate temperature control with a gradient (change) not to exceed 30C/hr.

In a closed or multi-unit rack, ensure that the unit has adequate airflow through the
front door and back door and that the ambient air temperature requirements are met.

Ensure that the front bezel and back panel clearances are met.

Ensure that cables at rear of unit do not obstruct exhaust airflow.

If installing in a closed cabinet, ensure that the front and rear doors have at least
65% open area to ensure adequate airflow for cooling.

Front bezel requires 1.56 inches (4.0 cm) of unobstructed clearance.

Back panel requires 5 inches (12.7 cm) of unobstructed clearance.

AC power outlets must be provided with an earth ground conductor (safety ground). A
safe electrical earth connection must be provided to each power cord.

Required voltage: 200-240 V~. Frequency: 50 to 60 Hz.

System specifications
Table 2 DD9500 system specifications

Model

Watts

BTU/hr

Power (VA)

Weight

Width

Depth

Height

DD9500

1887

6444

1981

117 lb / 53.2
kg

19 in / 48.3
cm

29.5 in / 74.9
cm

7 in / 17.8 cm

Operating temperature: 50 to 95 F (10 to 35 C), derate 1.1 C per 1000 feet,

above 7500 feet up to 10,000 feet

Operating humidity: 20% to 80%, non-condensing

Non-operating temperature: -40 to +149 F (-40 to +65 C)

Operating acoustic noise: Sound power, LWAd, is 7.7 bels.

Description of the system

Installation Guide

DD9500 front panel

The four solid state drives (SSDs), the storage processor (SP), and the fans are accessed
from the front of the system. The SP must be pulled out to provide access to the DIMMs.
The fans are accessed without pulling or removing the SP and they are hot-swappable.
The photo shows the interfaces on the front of the system.
Figure 2 Front panel components

1. Slot 0 SSD
2. Slot 1 SSD
3. Slot 2 SSD
4. Slot 3 SSD
5. Front LEDs
6. USB ports
7. Power button
8. Fan tray thumbscrew (left)
9. SP module thumbscrew to secure the ejector handle
10. Fan tray thumbscrew (right)

Front LED indicators

On the front panel to the right of SSD #4 (in Slot 3) are 3 LEDs that show high level
system status. The System Power LED glows blue to show the system is powered on.
Note

The system can have power (be plugged in) but the blue LEDs are off if the system is
powered off.
The SP Service LED is normally off, but glows amber whenever the storage processor (SP)
requires service. The Enclosure Service LED is normally off, but glows amber whenever
the SP or other replaceable parts require service. The System Power and Enclosure
Service LEDs are visible through the front bezel.

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 3 Service LEDs

1. SP service LED Amber light indicates that the SP or one of its components such
as the memory risers or memory DIMMs needs service.
2. Enclosure Service LED This is normally off, but amber light indicates that the
enclosure or something within the enclosure the fans, SP, I/O modules,
management module etcrequires service.
3. System power LED Blue light indicates system running

DD9500 front panel

Installation Guide

The power button shown in the picture is used when a system needs to be powered up
after a shut down using the system poweroff command. Once power is restored the
system power LED light turns blue.
Figure 4 Power button

1. System power LED Blue light indicates system running

2. Power button
The LEDs in the front are shown in the following figure.
Figure 5 Front LEDs

1. SSD LED in slot 0

2. SSD LED in slot 1
3. SSD LED in slot 2
4. SSD LED in slot 3
5. System power LED Blue light indicates system running
8

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Table 3 Front panel LED status indicators

Part

Description or Location

State

System, SP fault

Exclamation point within a

triangle

Dark indicates normal operation. Amber

indicates failure.

System, chassis
fault

Exclamation point within a

triangle

Dark indicates normal operation. Amber

indicates a fault condition.

SSD

Top LED

Solid blue, disk ready, blinks while busy.

SSD

Bottom LED

Dark indicates healthy. Solid amber

indicates disk fail.

DD9500 rear panel

The figure shows components identified for the rear of the system highlighted within red
rectangles.
Figure 6 Rear panel overview

1. Four power supply units

2. Serial number tag
3. Management module
4. NVRAM and IO modules
The figure shows the rear panel LEDs.

DD9500 rear panel

Installation Guide

Figure 7 Rear panel LEDs

1. Management module LED

2. Power supply LED
3. NVRAM LED (on the handle)
4. I/O module LED (on the handle)

I/O module slot assignments

The following figure shows the location of the NVRAM and I/O modules.
Figure 8 Location of NVRAM and I/O modules

1. NVRAM moduleslot 0
2. I/O modulesslots 1 to 11 (See the I/O module slot assignments table.)

Note

Slots 2, 3, and 6 (three I/O slots) are used for SAS I/O modules for systems without
Extended Retention.

10

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 8 Location of NVRAM and I/O modules (continued)

Note

Slots 2, 3, 6, and 9 (four I/O slots) are for SAS I/O modules for systems with Extended
Retention.
The table shows the I/O module slot assignments for the DD9500 system. Each type of
I/O module is restricted to certain slots.
Table 4 I/O module slot assignments

Slot Number DD9500

DD9500 with Extended Retention

Software

NVRAM

NVRAM

Fibre Channel (FC), Ethernet or empty FC, Ethernet or empty

SAS

SAS

SAS

SAS

FC, Ethernet or empty

FC, Ethernet or empty

FC, Ethernet or empty

FC, Ethernet or empty

SAS

SAS

FC, Ethernet or empty

FC, Ethernet or empty

FC, Ethernet or empty

FC, Ethernet or empty

Not available (contains a filler)

SAS

10

FC, Ethernet or empty

FC, Ethernet or empty

11

FC, Ethernet or empty

FC, Ethernet or empty

DD9500 rear panel

11

Installation Guide

Define the Data Domain system information for your site

An installation requires information unique to your site. Before starting the installation,
provide all appropriate values for your site. The worksheet is provided to define and
document system information, configuration, and settings.

Setup worksheet
Table 5 Worksheet
1.

A fully qualified host name for the system:

2.

DNS domain name:

3.

Default gateway IP address (if no DHCP):

4.

Host name from which to administer the system:

5.

Administrators email address (or admin group alias):

6.

Description of the systems physical location (Optional) :

7.

Mail server (SMTP) host name:

8.

Time zone name (default is US/Pacific):

9.

System Controller ID from the License Code document provided

in the accessory kit. Use this ID to obtain the unique WWPN for
this controller using the WWPN tool at:
https://support.emc.com

10.

Record the serial number (SN) found on the SN pull-out tab on

the back of the chassis. This will be your configuration password.

11.

CIFS authentication method: Workgroup

12.

13.

Workgroup name

Backup user name

Password

CIFS authentication method: Active Directory

l

Realm name

Domain administrator name

Password

Licenses, which consist of characters in this format:

ABCD-ABCD-ABCD-ABCD
For systems with EMC serial numbers:
ABCD-ABCD-ABCD-ABCD-ABCD
For DD OS 5.1 and later for shelf capacity
licenses:
ABCD-ABCD-ABCD-ABCD-ABCD-ABCD-AB

Optional Data Domain software and hardware upgrades require a

license.

12

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Table 5 Worksheet (continued)

For a list of licensed features, see the EMC Data Domain Operating
System Administration Guide for your release.
For a list of new features that require a license, see the Release
Notes for your release.
14.

If you are using DHCP (Dynamic Host Configuration Protocol), you

may need the MAC (Media Access Control) address, which
consists of 12 alphanumeric characters. This is sometimes used
to configure the DHCP server, which assigns an IP address for a
Data Domain system. The MAC address is printed on a label and
should be visible. Its location varies according to system model.

15.

If you are not using DHCP, have the following available:

l

Interface IP addresses

Interface netmasks - you can configure different network

interfaces on a Data Domain system to different subnets.

Routing gateway IP address - the IP address of the routing

gateway.

DNS server list - a comma-separated list of IP addresses of

your DNS servers (only if you are using DNS).

Site domain name - the domain name of the system, such as

company.com.

Fully qualified hostname for Data Domain system - the

hostname of the system that includes the domain name,
such as dd01.company.com

16.

Other information:

17.

Other information:

Unpack the system

1. Remove the accessories and rail mount kit from the shipping packages.
2. Remove the controller and the bezels from the shipping packages.
Note

For field installations, the controller has temporary handles pre-fitted at the factory to
help in removal of the system from the box and for placing it in a rack. While the
controller is being placed in a rack, the handles attached to the chassis can be
removed by loosening the thumbscrew on each handle. The handles must be saved
for future use.
CAUTION

Data Domain systems are heavy. Always use two people or a mechanical lift to move
a system. The chassis displays warning labels.

Unpack the system

13

Installation Guide

Figure 9 Warning about lifting the system

3. Remove expansion shelves and their bezels from the shipping packages.

Install the rack brackets

EMC data Domain systems are installed into racks using the rail bracket hardware.

Shelf brackets and cable management assembly

The rack mounting kits are compatible with racks that have front-to-rear post spacing
between 24 inches and 36 inches. The hardware fits the following types of mounting
holes:
l

7.1 mm round holes

.375 inch / 9.2 mm square holes

M5, M6, 12-24, and 10-32 threaded holes

The controller rail kit includes the following items:

l

Two bracket assemblies, one marked for the left side and one marked for the right
side of the rack

Figure 10 Rail bracket inside

14

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 10 Rail bracket inside (continued)

1. Left inside bracket

2. Right inside bracket
Figure 11 Rail bracket outside

1. Left outside bracket

2. Right outside bracket
A cable management assembly (CMA), for organization of cables at the rear of the
system, is already installed onto the DD9500 system on an EMC rack. For field installed
systems, the CMA is shipped with the DD9500 system.
Figure 12 Cable management assembly (CMA)

Shelf brackets and cable management assembly

15

Installation Guide

Install rail brackets on the Data Domain and EMC racks (for square or round hole
racks)
Note
l

If you are using a rack with threaded holes, skip this section and go to Install rail
brackets using the adapter hardware (for threaded hole racks) on page 20 section.

The Data Domain system is 4 rack units (RU) tall so make sure the location in the rack
fits the product. Attach the bracket assembly to the lowest RU of the 4-RU opening.

To comply with Data Domain rack mounting guidelines, the system controller should
be installed in the pre-defined space in the rack for system controllers. Refer to the
Installation and Setup Guide for your system.

Do not hold the bracket assembly in a vertical position as the parts may separate.

Procedure
1. At each rack post, determine the vertical position in the rack where the brackets are to
be installed. The top-most mounting hole for a particular rack unit (RU) mounting
position is typically identified by a mark or hole. The bracket will be installed in the
bottom hole of the 4 RU opening.
CAUTION

If the bracket is mounted in holes that are not vertically aligned from front to back,
the bracket may be damaged and mounting will not be secure.
2. As needed, select the bracket marked right or left. The rear of the bracket contains an
adjustable piece.
Figure 13 Rail bracket inside

1. Left inside bracket

2. Right inside bracket

16

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 14 Rail bracket outside

1. Left outside bracket

2. Right outside bracket

Install rail brackets on the Data Domain and EMC racks (for square or round hole racks)

17

Installation Guide

3. From the rear of the system, hold the bracket against the inside of the rack posts.
Align the rear guide pin and slide the bracket towards the front. The guide pins can
help to temporarily hold the rack mount bracket in place. Attach the bracket to the
rear of the rack using the furnished screws. There are five screw holes. The picture
shows two screws attached to the rear rack post.
Figure 15 Insert screw in the back

CAUTION

If the bracket is mounted in holes that are not vertically aligned from front to back,
the bracket may be damaged and mounting will not be secure.

18

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

4. Pull the adjustable sliding part of the bracket towards the front until it is close to, but
not touching, the front of the rack.
Figure 16 Insert screw in the front

5. Attach the front of the brackets with two screws each in the two middle holes
(innermost holes) as shown in the picture.
Figure 17 Attach bracket to front of rack

6. Verify that the bracket is level.

7. Repeat the steps to attach the remaining bracket to the other side of the rack.
8. After installing both brackets, make sure that they are level with one another.

Install rail brackets on the Data Domain and EMC racks (for square or round hole racks)

19

Installation Guide

Install rail brackets using the adapter hardware (for threaded hole racks)
Note
l

If you are using a rack with square or round holes, go to Install rail brackets on the
Data Domain and EMC racks (for square or round hole racks) on page 16 section.

Only use this procedure if your rack has tapped holes that are M5, M6, 10/32, or
12/24.

The adapter hardware is shipped in the rack mount kit.

You will need a long handled screwdriver with a shank diameter less than 7.0 mm
and the wrench (included in the kit) to tighten the nuts.

Procedure
1. Locate the two adapters from the rail kit.
Figure 18 Adapters

1. Long adapter
2. Short adapter
2. Attach the long adapter to the front of each rail using M5 screws.

20

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 19 Attaching the front rail with the screw

Figure 20 Attaching the front rail adapter with a wrench

3. Attach the small adapter to the rear of each rail using M5 screws.

Install rail brackets using the adapter hardware (for threaded hole racks)

21

Installation Guide

Figure 21 Rear bracket attached to rail

4. At each rack post, determine the vertical position in the rack where the rails are to be
installed. The top-most mounting hole for a particular rack unit (RU) mounting
position is typically identified by a mark or hole. Racks may also be screen-printed to
show the positions of the rack units.
Note
l

To comply with Data Domain rack mounting guidelines, the system controller
should be installed in the pre-defined space in the rack for system controllers.
Refer to the Installation and Setup Guide for your system.

Two people may be required to attach the rail/bracket assembly to the rack.

5. Install the screws supplied in the adapter kit to the rack. For example, the 10-32
threaded hole rack would require the installation of the 10-32 screws. Install the
screws in the appropriate locations until they are tight against the rack.
6. As needed, select the bracket marked right or left. Orientation assumes you are facing
the front of the rack.
7. Slide the adjustable part of the bracket partly open.
8. Attach the first rail to the rack as follows:
a. Hold the rail against the inside of the rack with the rear bracket flush with the rear
of the rack. Use the screws threaded into the rack to hold the rear of the rail kit in
place.
b. Pull the front of the rail until it is flush with the inside of the rack front.
c. Attach the rails to the rack by installing the appropriate nuts onto the screws
threaded into the rack. Use the supplied wrench to tighten the nuts. Do this for the
front and rear of the rail kit.
d. Attach the rear of the rail/bracket assembly to the rear of the rack. Secure each
screw.

22

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 22 Attach front rail adapter

9. Repeat the steps for the second rail.

10.After installing both rails, make sure that they are level with one another.

Install the DD9500 system into a rack

CAUTION

Data Domain systems are heavy. Always use two people or a mechanical lift to move a
system. The chassis displays warning signs.
Figure 23 Warning about lifting the system

Install the DD9500 system into a rack

23

Installation Guide

CAUTION
l

To comply with Data Domain rack mounting guidelines, the system controller should
be installed in the pre-defined location for the system controller in the rack.

Do not apply AC power to the DD9500 system controller until all expansion shelves
and cables are installed.

Make sure the PSNT label, attached to the left rear of the chassis is not damaged or
snagged during the installation of the system into the rack.

Procedure
1. Identify the designated location for the system controller in the rack. See diagram for
the location shown with an arrow to place the DD9500 system.
Note

The designated slots in the rack shown with an arrow is the recommended location for
the DD9500 system to support the cabling shown in the diagram. Other locations may
require different cable lengths for some configurations. See the Connecting the
expansion shelves and the controller on page 31 section for the details about
connecting the expansion shelves to the controller. You must refer to the Notes and
Information on page 31 section to understand the markings used. The circle
is
used to indicate a HOST port and the diamond
is used to indicate an EXPN
(Expansion) port. Refer to the EMC Data Domain ES30 Shelf Expansion Hardware Guide
and the EMC Data Domain DS60 Shelf Expansion Hardware Guide for detailed
instructions for cabling diagrams.
Figure 24 Pre-defined location for DD9500

2. From the front of the rack, lift the DD9500 system using the handles supplied for
lifting to install the system in the rack in the correct location.
Figure 25 Four handles attached to the chassis

24

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

3. At each side, align the bottom of the chassis with the lip of each installed rack
bracket.
4. Carefully slide the chassis into the rack and remove the back handles while
supporting the chassis weight. Continue to slide the rest of the chassis and remove
the front handles. Finally, push the chassis all the way into the back of the rack.
5. The rear of the chassis should engage with the tabs located in the rear of the rack
mount kit.
6. At the front, attach the system to each installed bracket using the screws on the front
of the system. The screws are shown in red circles in the photo.
Figure 26 System on a rack

Install the DD9500 system into a rack

25

Installation Guide

7. Check the PSNT label at the rear of the chassis.

Figure 27 Location of serial number tag

Mount the cable management assembly

A cable management assembly (CMA), for organization of cables at the rear of the
system, is already installed onto the DD9500 system on an EMC rack.
For field installed systems, the CMA is shipped separately.
Note

For non-EMC racks, it is acceptable to use the cable management products provided by
the rack vendor.

26

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Install the EMC cable management assembly (CMA)

Procedure
1. Take out the cable management assembly (CMA) from its packaging.
Figure 28 EMC CMA front

2. Locate the two blue knobs (on the left and right sides of the CMA) in the back which
you will need to pull away from the side of the CMA brackets to install the CMA in the
rack.
Figure 29 EMC CMA back

Install the EMC cable management assembly (CMA)

27

Installation Guide

Figure 30 Blue knob positions

1. Knob not pulled outBefore CMA installation

2. Knob pulled outCMA ready for installation
3. Pull the knobs away from the side of the CMA brackets towards the direction of the
white arrow (see picture) and turn the blue knobs in the direction of the yellow arrow
(on the left and right sides of the CMA) so the tip of the knob is pulled away from the
side of the bracket to fit in the rail slot.
Figure 31 EMC cable management assembly back inside

4. Locate the slots and the hole in the EMC rail to attach the CMA by following the arrows
in the picture. Align and insert the CMA tabs in the slots and the blue knob in the hole
of the rail bracket on both sides.
28

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 32 Rear of the rack mount rail

5. Insert cable management assembly into rear of rack mount rails. See the photo.
Figure 33 Installing the CMA on the rack

6. When the cable management assembly is securely installed into the rack mount rails,
then rotate the two blue knobs clockwise or counterclockwise to lock the cable
management assembly into the rack mount rails.
7. To adjust the CMA position up or down, pull on the orange latches and pull up or
down on the arm simultaneously as needed for accessing the power cables.
Note

You do not need to remove the CMA to access the I/O modules, the managements
module, and the powers supply units for removal and replacement. Just adjust the
CMA arms.

Install the EMC cable management assembly (CMA)

29

Installation Guide

Figure 34 Adjusting the CMA plates

Installing the expansion shelves into the racks

CAUTION
l

EMC Data Domain systems are heavy. Always use two people or a mechanical lift to
move and install a Data Domain system. Use caution to install the expansion
shelves.

Ensure that each rack is securely anchored to prevent tipping.

1. From the front of a rack, lift the shelf to the designated rack location.
2. Add shelves to the racks in order, one at a time, from the bottom of a rack to the top
filling each string in that rack before going to the next.
Note

Strings in add-on racks may connect to the same string number in other racks.
Shelves are added in the order V1.1, V1.2, V.13, V1.4, V2.1, V2.2, and so on. As
shown in the diagrams, shelves are labeled VN.M. VN refers to string "N" and the "M"
is the number of the shelf in the string. For example, V3.2 refers to the second shelf in
the third string.
3. Secure each expansion shelf in the rack.

30

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Connecting the expansion shelves and the controller

Multiple expansion shelves are connected together and to the controller with qualified
SAS cables.
Note

You must save the extra SAS cables for future use.
The diagrams in the following sections show recommended cabling and component
placement of a system and shelves in the rack(s). The cables that are provided support
the controller and shelves in the rack positions as shown in the diagrams.
l

Refer to the diagrams in the Connecting multiple ES30 shelves to the DD9500
system on page 33 to connect a DD9500 system.

Refer to the diagrams in the Connecting multiple ES30 shelves to the DD9500 system
with Extended Retention on page 36 to connect a DD9500 system with Extended
Retention.

Refer to the diagrams in theConnecting multiple DS60 shelves to the DD9500

system on page 39 to connect a DD9500 system.

Refer to the diagrams in the Connecting multiple DS60 shelves to the DD9500 system
with Extended Retention on page 43 to connect a DD9500 system.

Table 6 Minimum and maximum configurations

System

Maximum
Appliance
Capacity

Minimum
Appliance
Shelf
Count

Maximum
Appliance Shelf
Count

Extended
Retention
Systems
(ER)
Capacity

Maximum
Shelves for
Extended
Retention

DD9500

864 TB
usable

4 ES30s

30 ES30s

1728 TB
usable

56

DD9500

1DS60 (fully 6DS60s (fully

loaded) with loaded) with 60
60 drives
drives

For more information about specific shelf cabling rules and guidelines for different types
of shelves, see:
l

EMC Data Domain ES30 Expansion Shelf Hardware Guide

EMC Data Domain DS60 Expansion Shelf Hardware Guide

Notes and Information

Note

Cables that connect to the DD9500 system have an HD-mini-SAS connector. The other
end that connects to an ES30 has a mini-SAS connector with a
port. Cables between
ES30s have mini-SAS connectors on both ends.
l

This guide describes the installation of new systems comprised of all ES30 expansion
shelves. Configurations including a mix of ES30 SATA and ES30 SAS shelves are
subject to additional configuration constraints. Refer to the EMC Data Domain ES30
Connecting the expansion shelves and the controller

31

Installation Guide

Shelf Expansion Hardware Guide and the EMC Data Domain DS60 Shelf Expansion
Hardware Guidefor detailed instructions for mixing shelf types.
l

Cables have an HD-mini-SAS end that connects to the controller and a mini-SAS with
a
end that connects to the shelves.

Cables should be dressed to the side of the rack and supported with Velcro straps to
allow for easy removal, as needed, of system components. You must refer to the EMC
Data Domain ES30 Shelf Expansion Hardware Guide and the EMC Data Domain DS60
Shelf Expansion Hardware Guide for detailed instructions for rack power connection
diagrams for EMC racks.
CAUTION

The racking location can be matched in non-EMC racks; however, the power
connections cannot be matched.
l

The shelf uses the markings

(Expansion) port.

to indicate a HOST port and

to indicate an EXPN

Cabling between adjacent shelves in a string (loop) is done with the 1M SAS cables
that are delivered with the shelves. The cables have the matching markings
and
for identification.

32

DD9500 system has a minimum of 3 SAS I/Os for the base system and 4 SAS I/Os for
the Extended Retention system.

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Connecting multiple ES30 shelves to the DD9500 system

1. Add shelf-to-shelf cables between shelves in a loop and to the controller as shown in
the diagram.
a.

Cable from the B Controller EXPANSION

port of the lower shelf to the B
controller HOST
port of the next higher shelf.

b. Then cable from the A Controller HOST

EXPANSION

port of lower shelf to the A controller

port of the next higher shelf

2. Refer to the diagram for port connections.

Figure 35 Cabling for a DD9500 system

3. Refer to the cabling instructions in the table.

Table 7 Cabling instructions

String
(Loop)

I/O - Port

Shelf Port

Length*

I/O 3 - Port 1

B controller HOST

port of shelf V1.1

2M

I/O 2 - Port 0

A controller HOST
in V1

port of the highest number shelf

2M

Connecting multiple ES30 shelves to the DD9500 system

33

Installation Guide

Table 7 Cabling instructions (continued)

String
(Loop)

I/O - Port

Shelf Port

Length*

I/O 3 - Port 0

B controller HOST

port of shelf V2.1

2M

I/O 6 - Port 1

A controller HOST
in V2

port of the highest number shelf

2M

I/O 2 - Port 1

B controller HOST

port of shelf V3.1

2M

I/O 6 - Port 0

A controller HOST
in V3

port of the highest number shelf

2M

I/O 3 - Port 3

B controller HOST

port of shelf V4.1

3M

I/O 2 - Port 2

A controller HOST
in V4

port of the highest number shelf

3M

I/O 3 - Port 2

B controller HOST

port of shelf V5.1

3M

I/O 6 - Port 2

A controller HOST
in V5

port of the highest number shelf

3M

I/O 2 - Port 3

B controller HOST

port of shelf V6.1

3M

I/O 6 - Port 3

A controller HOST
in V6

port of the highest number shelf

3M

* Cable lengths shown are designed for Data Domain or EMC racks. Longer cables (up
to 5M) can be used.
4. Connect the cables on the new 40U-P racks based on the recommended diagram.
5. Use the cable management assembly to support and organize all cables from the
DD9500 system.
6. Refer to the recommended cabling diagram for two racks.
Note

The racks are filled from bottom up.

34

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 36 Recommended cabling for DD9500 system with two racks

Connecting multiple ES30 shelves to the DD9500 system

35

Installation Guide

Connecting multiple ES30 shelves to the DD9500 system with Extended Retention
1. Add shelf-to-shelf cables between shelves in a loop and to the controller as shown in
the recommended diagram provided in this section.
a.

Cable from the B Controller EXPANSION

port of the lower shelf to the B
controller HOST
port of the next higher shelf.

b. Then cable from the A Controller HOST

EXPANSION

port of lower shelf to the A controller

port of the next higher shelf

2. Refer to the diagram for port connections.

Figure 37 Cabling for a DD9500 system with Extended Retention

3. Refer to the cabling instructions in the table.

Table 8 Cabling instructions for DD9500 system with Extended Retention

36

String
(Loop)

I/O - Port

Shelf Port

I/O 3 - Port 1

B controller HOST

port of shelf V1.1

2M

I/O 2 - Port 0

A controller HOST
in V1

port of the highest number shelf

2M/3M

EMC Data Domain DD9500 System Installation Guide

Length

Installation and Setup Guide

Table 8 Cabling instructions for DD9500 system with Extended Retention (continued)

String
(Loop)

I/O - Port

Shelf Port

Length

I/O 3 - Port 0

B controller HOST

port of shelf V2.1

2M

I/O 9 - Port 1

A controller HOST
in V2

port of the highest number shelf

2M /5M

I/O 2 - Port 1

B controller HOST

port of shelf V3.1

2M

I/O 6 - Port 0

A controller HOST
in V3

port of the highest number shelf

2M /5M

I/O 3 - Port 3

B controller HOST

port of shelf V4.1

3M

I/O 2 - Port 2

A controller HOST
in V4

port of the highest number shelf

3M/5M

I/O 3 - Port 2

B controller HOST

port of shelf V5.1

3M

I/O 9 - Port 2

A controller HOST
in V5

port of the highest number shelf

3M/5M

I/O 2 - Port 3

B controller HOST

port of shelf V6.1

3M

I/O 6 - Port 3

A controller HOST
in V6

port of the highest number shelf

3M/5M

I/O 9 - Port 0

B controller HOST

port of shelf V7.1

2M

I/O 6 - Port 1

A controller HOST
in V7

port of the highest number shelf

5M

I/O 6 - Port 2

B controller HOST

port of shelf V8.1

5M

I/O 9 - Port 3

A controller HOST
in V8

port of the highest number shelf

5M

4. Connect the cables on the new 40U-P racks based on the recommended diagram.
5. Use the cable management assembly to support and organize all cables from the
DD9500 system.
6. Refer to the recommended cabling diagram for five racks.
Note

The racks are filled from bottom up.

Connecting multiple ES30 shelves to the DD9500 system with Extended Retention

37

Installation Guide

Figure 38 Recommended cabling for DD9500 system with 56-shelf Extended Retention software

38

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Connecting multiple DS60 shelves to the DD9500 system

1. Add shelf-to-shelf cables between shelves in a loop and to the controller as shown in
the diagram.
a.

Cable from the B Controller EXPANSION

port of the lower shelf to the B
controller HOST
port of the next higher shelf.

b. Then cable from the A Controller HOST

EXPANSION

port of lower shelf to the A controller

port of the next higher shelf

2. Refer to the diagram for port connections.

Figure 39 Cabling for a DD9500 system

3. Refer to the cabling instructions in the table.

Table 9 Cabling instructions

String
(Loop)

I/O - Port

Shelf Port

Length*

I/O 3 - Port 1

B controller HOST

port of shelf V1.1

2M

I/O 2 - Port 0

A controller HOST
in V1

port of the highest number shelf

2M

Connecting multiple DS60 shelves to the DD9500 system

39

Installation Guide

Table 9 Cabling instructions (continued)

String
(Loop)

I/O - Port

Shelf Port

Length*

I/O 3 - Port 0

B controller HOST

port of shelf V2.1

2M

I/O 6 - Port 1

A controller HOST
in V2

port of the highest number shelf

2M

I/O 2 - Port 1

B controller HOST

port of shelf V3.1

2M

I/O 6 - Port 0

A controller HOST
in V3

port of the highest number shelf

2M

I/O 3 - Port 3

B controller HOST

port of shelf V4.1

3M

I/O 2 - Port 2

A controller HOST
in V4

port of the highest number shelf

3M

I/O 3 - Port 2

B controller HOST

port of shelf V5.1

3M

I/O 6 - Port 2

A controller HOST
in V5

port of the highest number shelf

3M

I/O 2 - Port 3

B controller HOST

port of shelf V6.1

3M

I/O 6 - Port 3

A controller HOST
in V6

port of the highest number shelf

3M

* Cable lengths shown are designed for Data Domain or EMC racks. Longer cables (up
to 5M) can be used.
4. Connect the cables on the new 40U-P racks based on the recommended diagram.
5. Use the cable management assembly to support and organize all cables from the
DD9500 system.
6. Refer to the recommended cabling diagram for two racks.
Note

The racks are filled from bottom up.

40

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 40 Recommended cabling for DD9500 system (3TB drives)

Connecting multiple DS60 shelves to the DD9500 system

41

Installation Guide

Figure 41 Recommended cabling for DD9500 system (4TB drives)

Note

One DS60 shelf in this set has 30 drives.

42

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Connecting multiple DS60 shelves to the DD9500 system with Extended Retention
1. Add shelf-to-shelf cables between shelves in a loop and to the controller as shown in
the recommended diagram provided in this section.
a.

Cable from the B Controller EXPANSION

port of the lower shelf to the B
controller HOST
port of the next higher shelf.

b. Then cable from the A Controller HOST

EXPANSION

port of lower shelf to the A controller

port of the next higher shelf

2. Refer to the diagram for port connections.

Figure 42 Cabling for a DD9500 system with Extended Retention

3. Refer to the cabling instructions in the table.

Table 10 Cabling instructions for DD9500 system with Extended Retention

String
(Loop)

I/O - Port

Shelf Port

Length

I/O 3 - Port 1

B controller HOST

port of shelf V1.1

2M

I/O 2 - Port 0

A controller HOST
in V1

port of the highest number shelf

2M/3M

Connecting multiple DS60 shelves to the DD9500 system with Extended Retention

43

Installation Guide

Table 10 Cabling instructions for DD9500 system with Extended Retention (continued)

String
(Loop)

I/O - Port

Shelf Port

Length

I/O 3 - Port 0

B controller HOST

port of shelf V2.1

2M

I/O 9 - Port 1

A controller HOST
in V2

port of the highest number shelf

2M /5M

I/O 2 - Port 1

B controller HOST

port of shelf V3.1

2M

I/O 6 - Port 0

A controller HOST
in V3

port of the highest number shelf

2M /5M

I/O 3 - Port 3

B controller HOST

port of shelf V4.1

3M

I/O 2 - Port 2

A controller HOST
in V4

port of the highest number shelf

3M/5M

I/O 3 - Port 2

B controller HOST

port of shelf V5.1

3M

I/O 9 - Port 2

A controller HOST
in V5

port of the highest number shelf

3M/5M

I/O 2 - Port 3

B controller HOST

port of shelf V6.1

3M

I/O 6 - Port 3

A controller HOST
in V6

port of the highest number shelf

3M/5M

I/O 9 - Port 0

B controller HOST

port of shelf V7.1

2M

I/O 6 - Port 1

A controller HOST
in V7

port of the highest number shelf

5M

I/O 6 - Port 2

B controller HOST

port of shelf V8.1

5M

I/O 9 - Port 3

A controller HOST
in V8

port of the highest number shelf

5M

4. Connect the cables on the new 40U-P racks based on the recommended diagram.
5. Use the cable management assembly to support and organize all cables from the
DD9500 system.
6. Refer to the recommended cabling diagram.
Note

The racks are filled from bottom up.

44

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Figure 43 Recommended cabling for DD9500 system (3TB drives) with Extended Retention software

Connecting multiple DS60 shelves to the DD9500 system with Extended Retention

45

Installation Guide

Figure 44 Recommended cabling for DD9500 system (4TB drives) with Extended Retention software

Note

Out of 10 DS60 shelves, one DS60 shelf in this set has 30 drives.

46

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Install the bezel

There are two types of bezels for the DD9500 system. Both bezels function exactly the
same; the difference is merely cosmetic.
l

Factory bezelused for racked systems built and shipped from the EMC factory (see
picture).

Field bezelused when the DD9500 system is installed into a rack at the customer
site (see picture).

Procedure
1. Install the bezel on your DD9500 system by grasping both hand holds and pressing
toward the center of the bezel until the latches attach to the sides of the chassis. The
red circles identify the latches on each bezel. Make sure the handhold locks lock into
place.
Figure 45 Attaching the factory bezel

Figure 46 Attaching the field bezel

Note
l

Depress the two handhold positions to remove the bezel as needed.

The bezel contains a lock and is shipped with a key. If the bezel is difficult to
attach, check that the lock is unlocked.

Install the bezel

47

Installation Guide

Connect data cables

1. Enable data transfer Ethernet connectivity. Repeat for each connection.
a. If using 1 Gb copper Ethernet, attach a Cat 5e or Cat 6 copper Ethernet cable to an
RJ-45 Ethernet network port (start with ethMa and go up).
b. If using 10 Gb copper Ethernet with an SFP+ connector, use a qualified SFP+
copper cable.
c. If using 1/10 Gb fiber Ethernet, use MMF-850nm cables with LC duplex
connectors.
d. For 10GBaseT connections, use Cat6a S-STP Ethernet cables.
2. Enable data transfer Fibre Channel (FC) connectivity. Repeat for each connection.
a. Attach a Fibre Channel fiber optical cable (LC connector) to an I/O module port on
the controller, and attach the other end (LC connector) to an FC switch or to an FC
port on your server.

Power on all systems

Note

Power on all expansion shelves first before powering on the controller.

1. Connect power cables to each expansion shelf receptacle and attach the retention
clips.
2. Provide power to power-on each expansion shelf. The shelves power on when
plugged in. Ensure that each shelf power cable is connected to a different power
source.
Note

Wait approximately 3 minutes after all expansion shelves are powered on before
powering on the controller.
3. Provide power to power-on the controller. The system powers on when plugged in.
Note

The DD9500 system should be powered from redundant AC sources. This allows one
AC source to fail or be serviced without impacting system operation. PSU0 and PSU1
should be attached to one AC source. PSU2 and PSU3 should be attached to the
other AC source.
a. Connect power cables to each receptacle and attach the retention clips.
b. Ensure that each power supply is connected to a different power source.

Enable administrative communication

Note

See the back panel of the DD9500 system for the location of the onboard interfaces.

48

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

1. Connect an administrative console to the serial port on the back panel of the system.
2.

Note

You must have 115200 baud rate for the DD9500 system to work properly; 9600
baud rate will not work for the DD9500 system.
Launch a terminal emulation program from your computer and configure the following
communication settings:
Table 11 Communications settings

Setting

Value

Baud rate

115200

Data bits

Stop bits

Parity

None

Flow control None

Emulation

VT-100

3. Select Enter on your keyboard to activate the console.

Note

If you do not see the prompt on your terminal to log in, then complete Step 4.
4. In the front of the DD9500 system, press the power button to turn the power on the
system. Check that the front blue power LED (with the circle with a dot) also turns on.
Figure 47 Power LED and power button

Enable administrative communication

49

Installation Guide

1. Power LED
2. Power button
5.

Note

The initial username is sysadmin and the initial password is the system serial
number.
Log into the Data Domain console using the sysadmin username.
localhost.localdomain login: sysadmin

6. Enter the default password, which is the system serial number (SSN). The SSN is on
the attached tag on the rear panel of the system. See the rear panel of the DD9500
system for the SSN tag.
Password: system_serial_number
Note

If you enter an incorrect password four consecutive times, the system locks out the
specified username for 120 seconds. The login count and lockout period are configurable
and might be different on your system. See the EMC Data Domain Operating System
Administration Guide and the EMC Data Domain Operating System Command Reference
Guide for setting these values.

Accepting the End User License Agreement (EULA)

The first time you log in to a Data Domain system, the End User License Agreement (EULA)
is displayed.
At the end of the EULA, you are prompted to accept it:
Press any key then hit enter to acknowledge the receipt of EULA
information
Note

The EULA must be accepted by a customer. An EMC representative should not accept this
agreement. If a customer is not present, press Ctrl-C to exit from the EULA acceptance
screen and continue the installation.
The customer can later enter the following to redisplay the EULA and accept it:
system show eula

Run the configuration wizard

The CLI configuration wizard starts automatically the first time the system boots. The
wizard prompts you through a series of questions that provide just enough information
for initial system configuration and basic network connectivity.
Note

You can initiate the CLI configuration wizard manually by entering the config setup
command.

50

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Configuring the network

Procedure
1. Enter yes to begin configuring the system.
Do you want to configure system using GUI wizard (yes|no) [no]
: yes

Answering yes initiates a shortened version of the CLI configuration wizard that
provides enough information to configure the system for network access. Afterward,
you can use the GUI (Data Domain System Manager) for additional configuration.
Answering no initiates a longer, more robust, version of the CLI configuration wizard.
2. Enter yes and change the password.
Note

If you are an EMC internal resource or partner, do not change the password unless
specifically directed to do so by the customer.
Change the 'sysadmin' password at this time? (yes|no):

3. Enter yes to configure the system for network connectivity.

Network Configuration
Configure Network at this time (yes|no)
[no]: yes

4. Enter yes to configure DHCP to obtain network parameters (such as, the hostname,
domain name, and IP addresses) dynamically from a DHCP server. Or enter no to
configure the parameters manually.
Use DHCP
Use DHCP for hostname, domainname, default gateway and
DNS servers? (At least one interface needs to be configured
using DHCP) (yes|no|?)

5. Enter a fully qualified domain name (FQDN) for the hostname; for example,
str01.yourcompany.com. Or accept the hostname, if the system was able to
discover it.
Enter the hostname for this system (fully-qualified domain name)[]:

6. Enter the DNS domain name; for example, yourcompany.com. Or accept the domain
name, if the system was able to discover it.
Domainname
Enter your DNS domainname []:

7. Enable and configure each Ethernet interface. Accept or decline DHCP for each
interface. If the port does not use DHCP to discover network parameters automatically,
enter the information manually.
Ethernet port eth0a
Enable Ethernet port eth0a (yes|no|?) [yes]: no
Ethernet port eth0b
Enable Ethernet port eth0b (yes|no|?) [no]: yes
Use DHCP on Ethernet port eth0b (yes|no|?) [no]:
Enter the IP address for eth0b
[192.168.10.185]:
Enter the netmask for eth0b
[255.255.255.0]:
Configuring the network

51

Installation Guide

8. Enter the IP address of the default routing gateway. Or accept the default gateway, if
the system was able to discover it.
Default Gateway
Enter the default gateway IP address
: 192.168.10.1

9. Enter the IPv6 address of the default routing gateway. Or accept the IPv6 address of
the default gateway, if the system was able to discover it. If IPv6 is not in use, leave
the field empty and press Enter to continue.
IPV6 Default Gateway
Enter the ipv6 default gateway IP address
:

10.Enter up to three DNS servers to use for resolving hostnames to IP addresses. Use a
comma-separated or space-separated list. Enter a space for no DNS servers. Or accept
the IP addresses of the DNS servers, if the system was able to discover them.
DNS Servers
Enter the DNS Server list (zero, one, two or three IP addresses)
: 192.168.10.1

11.A summary of the network settings displays. You can accept the settings (Save), reject
the settings and exit to the command line (Cancel), or return to the beginning of the
current section and change the settings (Retry). Entering Retry displays your
previous response for each prompt. Press Return to accept the displayed value or
enter a new one.
Pending Network Settings
Hostname
ddbeta1.dallasrdc.com
Domain name
dallasrdc.com
Default Gateway
192.168.10.1
DNS Server List
192.168.10.1
Port
Enabled
Cable
DHCP
IP Address
------------------------------eth0a
no
no
n/a
n/a
eth0b
no
no
n/a
n/a
eth0c
no
no
n/a
n/a
eth0d
no
no
n/a
n/a
ethMa
yes
yes
no
192.168.10.181
ethMb
no
no
n/a
n/a
ethMc
no
no
n/a
n/a
ethMd
no
no
n/a
n/a
ethMe
no
no
n/a
n/a
ethMf
no
no
n/a
n/a
------------------------------Do you want to save these settings (Save|Cancel|Retry): Save

Netmask or Prefix Length

-----------------------n/a
n/a
n/a
n/a
255.255.255.0
n/a
n/a
n/a
n/a
n/a
------------------------

12.The wizard exits to the CLI and the following message displays.
To complete this configuration in the Enterprise Manager, please set
your web browser address to http://<hostname_or_IP>/
then go to Maintenance -> More Tasks -> Launch Configuration Wizard.

After the CLI wizard finishes, a system reboot is recommended. Enter system reboot
to reboot the system.

Configuring additional system parameters

Most installations would benefit from the configuration of a few additional system
parameters, provided in this section for convenience.

52

EMC Data Domain DD9500 System Installation Guide

Installation and Setup Guide

Note

You can also use the EMC Data Domain (DD) System Manager GUI interface to configure
the system parameters. Open a web browser, and enter your Data Domain systems IP
address in the browsers address text box. Log in when the DD System Manager login
screen displays. Use the DD System Manager online help for more information.
Procedure
1. To set up the mail server, enter:
# config set mailserver mail.datadomain.com
The Mail (SMTP) server is: mail.datadomain.com

2. To set up the system location, enter:

# config set location "Dallas Regional Data Center Lab,
5000 Apple Drive Suite #130, Dallas, Tx"
The System Location is: Dallas Regional Data Center Lab,
5000 Apple Drive Suite #130, Dallas, Tx

3. To add one or more time servers, enter:

# ntp add timeserver 192.168.101.1
Remote Time Servers: 192.168.10.1

4. To enable the NTP daemon, enter:

# ntp enable
NTP enabled.

5. To change the system time zone, enter:

# config set timezone US/Central
The Timezone name is: US/Central
*** You made a change to the timezone setting. To fully effect
this change
*** (in currently running processes), you need to reboot the
machine.

6. Reboot the system for the time zone change to take effect:
# system reboot
The 'system reboot' command reboots the system. File access is
interrupted during the reboot.
Are you sure? (yes|no|?) [no]: yes
ok, proceeding.
The system is going down for reboot.

7. After the system completes the reboot, login again as sysadmin using the serial
number as a password. Press Ctrl-C to get through the EULA, sysadmin password
prompt, and config setup wizard.
8. Generate an autosupport sent to yourself to use as ACG input
# autosupport send [email protected]
OK: Message sent.

9. Generate an ACG using the produced ASUP.

Configuring additional system parameters

53

Installation Guide

Copyright 2015 EMC Corporation. All rights reserved. Published in USA.

EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without
notice.
The information in this publication is provided as is. EMC Corporation makes no representations or warranties of any kind with
respect to the information in this publication, and specifically disclaims implied warranties of merchantability or fitness for a
particular purpose. Use, copying, and distribution of any EMC software described in this publication requires an applicable software
license.
EMC, EMC, and the EMC logo are registered trademarks or trademarks of EMC Corporation in the United States and other countries.
All other trademarks used herein are the property of their respective owners.
For the most up-to-date regulatory document for your product line, go to EMC Online Support (https://support.emc.com).
54

EMC Data Domain DD9500 System Installation Guide