OmniScan MX2 Training Program

Phased Array Wedges

OmniScan MX2 Training Phased Array Wedges Overview

Phased array wedges perform the same function as conventional UT

wedges by coupling sound energy from the probe to the material at the
desired refracted angle and wave type.
Phased array wedges come in all shapes and sizes for various applications
and are an essential part of the inspection process.
Phased array wedges are used to assist the probe in beam formation for
shear wave and longitudinal wave inspections, just like UT.
1D Wedges typically used in OmniScan MX2 applications come in 3
varieties:
1. Shear wave angle beam
2. Longitudinal wave angle beam
3. Longitudinal wave straight beam

OmniScan MX2 Training Phased Array Wedges Overview cont.

Phased array wedges from Olympus are made of high quality Rexolite
material that has been tested at the factory for velocity tolerance, and
internal flaws prior to machining.
Rexolite is an isotropic material meaning it has a constant velocity in each
axis and is ideal for phased array wedge manufacturing.
Rexolite is more brittle than Lucite or typical plastic and more easily
damaged. Care should be taken not to over tighten screws or drop.

OmniScan MX2 Training Phased Array Wedges Overview

Wedges can be optimized for manual hand

inspection, automated scanner inspection,
or special applications.
Wedge features available include:

Carbide feet for protection from wear.

Built-in irrigation ports and channels.
Scanner and encoder attachments points.
Inner and outer component radius
curvature.
Water channels on base of wedge.
Stainless steel scanner guides.
Multiple positions for the probe.
.and more.

OmniScan MX2 Training Wedges Material - Rexolite

Rexolite is a rigid and transparent plastic produced by cross linking polystyrene with
divinylbenzene.
Rexolite is an isotropic material that has a constant velocity in each axis of 2330
meters/sec and impedance similar to water.
Rexolite has an outstanding dielectric constant of 2.5 to up to 500 GHz with an
extremely low dissipation factor making it well suited for advanced NDT, sonar
lenses, sonic medical systems, missile guidance systems, microwave circuitry and
many other ultrasonic and optical applications. (Does not filter the bandwidth)
Rexolite exhibits no permanent deformation under loads up to 2000 psi and at
temperatures between 20-125 degrees Celsius. (257 degrees Fahrenheit)
Rexolite can be machined with tolerances much tighter than Lucite or low grade
plastics.
For these reasons Rexolite is an ideal material for phased array wedge
manufacturing.

OmniScan MX2 Training Olympus Wedge Definition

The complete definition for wedges is available in the current Olympus

probe catalog and below.
The part number is divided into 4 sections and may or may not contain the
last two.

OmniScan MX2 Training Wedge Housing Compatibility

Olympus wedges are manufactured to be compatible with a type of

Olympus probe housing. Typical housing numbers are A2, A10, A12, etc.
and are printed on the probe and wedge.
Any probe and wedge of the same housing type are compatible.
Example: All SA12 wedges in the catalog are compatible with A12 probes
and all the parameters required for the phased array calculator are
available in the OmniScan MX2 wedge database.
In the SA12 example below we have options for shear wave angle beam,
longitudinal wave angle beam, and longitudinal straight beam.

OmniScan MX2 Training Wedge Housing Compatibility cont.

Some housing types can accommodate probe models of different pitch size and
frequency, and may not be symmetrical in the housing.
Wedges compatible with these types of probes contain separate probe position
options with separate attachment points including reversing the probe.
Care should be taken to ensure the correct probe, wedge, AND WEDGE
POSITION are selected from the wedge database.

A2 Housing
5L64
Position

2.25L64
Position

OmniScan MX2 Training Wedge Carbide Wear Pins

Use of carbide wear pins on the wedges is common for auto and semi-auto
inspections where high production or repetitive scanning is required.
The wear pins provide both protection from wear on the wedge, and stability for
improved performance and repeatability.
Wear pins should be secured in place with Lock-tight and require a constant
water supply through the water ports. UT couplant gel is not recommended.
Use of carbide wear pins directly affects wedge delay and sensitivity calibration.
Failure to complete the calibration process with the same couplant technique
and pin position as the inspection will result in a reduction of precision
measurement and repeatability.

OmniScan MX2 Training Wedge Refracted Angle

Included in the wedge label after the housing family (SA10, SA12,
etc) is the nominal refracted angle (N60S) in steel with no beam
steering.
To achieve a shear wave refracted angle of 60 degrees (N60S) in
steel the wedge is cut with an incident angle of 39 degrees in
Rexolite. (Snells law)
N55 and N60 are common wedge designs because this angle allows
good beam steering from approximately 30-70 degrees for most
probes\wedge combinations.
39 degrees in
Rexolite

60 degrees in
carbon steel
10

OmniScan MX2 Training 0L Straight Beam Wedge

A zero degree wedge is designed for both straight beam and angle beam
longitudinal wave inspection as is typically used in corrosion mapping or
composite lamination type inspections.
This type of wedge acts as a stand off delay and provides improved near
surface resolution compared to using a probe with no wedge.
The 0L wedge also protects the probe as scanning with no wedge exposes
the probe membrane to wear and damage.

11

OmniScan MX2 Training Wedge Curvature Definition Overview

Wedge coupling is essential for a good inspection and where the wedge is too large
to properly mate against the material, sound is impeded and the wedge must be
contoured.
The 3 most common types of wedge curvature for optimization of a particular
component, pipe or vessel inspection are:
1. Flat
2. AOD## (Axial Outside Diameter Curvature + Diameter)
3. COD## (Circumferential Outside Curvature + Diameter)

12

OmniScan MX2 Training Wedge Curvature Definition Overview

Other custom wedge configurations are available on request as well as wedges

machined to a particular component like a dove tail joint.

13

MX2 Wedge Curvature Definition AOD Wedges

AOD wedges are contoured for the pipe diameter for typical girth weld inspections in
the axial axis.
Depending on the footprint of the probe\wedge combination and pipe diameter, a flat
probe may be sufficient for the inspection eliminating the need for a contour.
The phased array calculator need not differentiate between flat and AOD wedges
because the probe element position (Height) is the same for both.
For this reason, separate entries for AOD wedges do not appear in the OmniScan
MX2 database. Both are calculated as flat.
In the Olympus probe catalog you will find a reference for the curvature limits for
common wedges based on housing type and nominal pipe diameter.

14

MX2 Wedge Curvature Definition COD Wedges

Inspection in the circumferential axis or Long seam type inspection requires a COD
wedge and special hardware and software considerations.
COD wedges are calibrated at the factory for precise incident angle to be used in the
focal law calculator. Each wedge is treated independently for precision.
The COD inspection for the OmniScan MX2 requires that the focal laws be built
externally with a computer based calculator like Tomoview and imported into the
OmniScan MX2 for use.

15

MX2 Training Program Integrated Wedges

Wedges can be integrated directly into the probe or custom built for specialized
scanners and mechanics.
Integrated wedges are used for angle beam and straight beam inspection.
The phased array calculator requires the same independent information for the
wedge parameters in relationship to the probe.

16

OmniScan MX2 Special Application Wedges - Rexoform

The Olympus Rexoform system uses a specialized 0 degree longitudinal

wedge for corrosion mapping applications.
The Rexoform wedge has an integrated mechanical support that is designed
to adapt to different pipe diameters eliminating the rocking effect and
minimize the need for a contoured wedge.

17

OmniScan MX2 Special Application Wedges - Hydroform

The Hydroform corrosion mapper is a form of a specialized phased array probe and
wedge using water as the coupling medium.
It uses a stable water column with an adjustable probe height to transmit sound into
the component for corrosion inspection and C-scan generation.
The Hydroform wedge parameters for the phased array calculator are selected
directly from the database in the MX2 software and use the velocity of water.
The benefits of using water as the wedge include improved component coupling and
improved near surface defect resolution.

18

OmniScan MX2 Special Application Wedges - Radii Solution

The Olympus Radii solution is a immersion corner

wedge for curved linear array probes.
Allows for internal and external radius inspection and
adjustment of different wedge height and radius size.
Wedge parameters are entered into the calculator for
correct beam formation.

19

OmniScan MX2 Special Application Wedges - Custom Contours

In this example the phased array wedge was manufactured to the same taper as
the component for a perfect fit.
Custom wedges than cannot easily be defined by the phased array calculator have
inherent limitations. The ability to calibrate wedge delay and sensitivity requires a
custom calibration block and precision beam steering and focusing is reduced.
The inspection below is for cracks using an amplitude C-scan and metal loss using
a position or Time of flight C-scan.

Position

C-scan

Amplitude C-scan

20

OmniScan MX2 Special Application Wedges - Aqualene Wedges

Aqualene is an elastomer designed specifically

for ultrasonic inspection applications.
Acoustic impedance is nearly the same as
water and its attenuation coefficient is lower
than many documented plastics.
Aqualene couplant reduces the drawbacks of
wet coupling when used on porous refractory
surfaces and acts as a thermal insulator.
Aqualene couplant products are available in
many sizes and thicknesses including custom
design specifications.
Benefit for customer phased array applications
include:
Flexible couplant pads and minimal water addition.
Low velocity delay lines.
Water box coupling system membranes.
21

OmniScan MX2 Training Wedge Selection in MX2 Software

In the OmniScan MX2 software the wedge selection and management can
be accessed from two locations:
Setup wizard.
2. Probe and wedge sub menu.
1.

Wedges are selected from the database. New or custom wedges can be
created and stored.
One wedge may have many entries based on probe position, orientation,
and different probe model within the same type of housing. (SA1, SA2, etc)
Care should be taken when selecting the wedge model in the software. It is
a common source of problems including angle error, wedge delay error, and
improper beam formation.

22

OmniScan MX2 Training Wedge Specification Data Sheet

Every wedge from Olympus is delivered with a wedge specification data

sheet that contains all of the parameter values to populate the OmniScan
MX2 database or external focal law calculator. These values are relative to
the probe and its orientation on the wedge. For that reason one wedge may
be listed many times in the database.

23

OmniScan MX2 Training Wedge Database Update on the Web

New wedges are added to the database periodically at different intervals

than the software updates. At any time the current wedge database can be
directly updated on the OmniScan MX2 memory card by downloading a
utility from the software support section of the Olympus web page at
www.olympus-ims.com

24

OmniScan MX2 Training Phased Array Wedge Parameters Overview

The following parameters

are required for the
OmniScan MX2 wedge
database and phased
array calculator:
Wedge model.
Wedge angle.
Wedge orientation. (Normal
or reverse)
Height of element #1 of the
probe (h1).
Wedge material velocity.
Primary and secondary
offsets (x,y).

25

OmniScan MX2 Training Phased Array Wedge Parameters - Angle

Question:
What is the affect on the UT data if the wedge angle is different than the
calculator (Wizard) input?
Answer:
Beam formation is incorrect resulting in angle, focusing, and delay errors that
cannot be overcome in the calibration process. Minor angle errors due to
machining tolerances are the same as conventional UT wedges and
typically need not be corrected with precision measurement on specific
wedge serial number.

26

OmniScan MX2 Training Phased Array Wedge Parameters - Angle

Question:
Can the angle of the wedge be measured if it is unknown?
Answer:
Yes. This can be done mechanically and ultrasonically. If it is different than the
database or more precision is required it can be entered as a new or
custom wedge. The procedure for measuring the wedge angle ultrasonically
is covered in the wedge delay calibration section.

27

OmniScan MX2 Training Phased Array Wedge Parameters - Orientation

Due to the scanner limitation or inspection access it is sometimes necessary

to reverse the orientation of the probe elements to accommodate the probe
cable.
This is a function of the wedge orientation and it is defined as either normal
or reverse. Selecting reverse will have the affect of reversing the probe
element wiring. (1-64 changes to 64-1)

28

OmniScan MX2 Training Wedge Parameters Height of Element 1

Question:
What is the affect on the UT data if the height of the first element is different
than the calculator (Wizard) input?
Answer:
The wedge delay of the A-scan is not calculated correctly resulting in depth
reading errors. The selected focus distance is short or long based on the
error. Angle is not affected. Wedge delay can be corrected in the calibration
wizard without reforming the focal laws but it will not correct the focus
position.

29

OmniScan MX2 Training Wedge Parameters Height of Element 1

Question:
Does normal usage result in wedge wear that will change the height of the first
element?
Answer:
Yes. This can be corrected in the wedge delay calibration wizard or created in
the wedge database as specific serial numbered wedge. This is normal and
can be minimized with use of carbide wear pins on the wedge. Unlike
probes, wedges in some environments are consumables.

30

OmniScan MX2 Training Phased Array Wedge Parameters - Height

Question:
Can the height of the first element on the wedge be measured if it is unknown?
Answer:
Only ultrasonically, not mechanically. This is done by using the fixed velocity of
the wedge as the component. (Inspecting the wedge) This process is
covered in a later section. It cannot be measured mechanically because
element #1 is hidden behind the membrane in the probe housing and it is
impossible to know the exact position to measure.

31

OmniScan MX2 Training Phased Array Wedge Parameters - Velocity

The velocity of the wedge must be known prior to formation of the focal
laws. It cannot be measured or corrected during the calibration process.
Most wedges from Olympus that are designed to be used with the
OmniScan MX2 are made of Rexolite.
Rexolite is an isotropic material that has a constant velocity in each axis of
2330 +\- 20 meters\sec
Wedge velocity like component velocity is directly related to the incident and
refracted angles and is an essential variable in the calculator. (Snells Law).
Temperature affects velocity and similarly to conventional UT the calibration
must be performed near the same wedge and component temperature as
the inspection.

32

OmniScan MX2 Training Wedge Parameters - Offsets

Offsets are the relationship of probe element #1 to the side and front of the
wedge. As pictured right, X is the primary offset and Y is the secondary
offset and is normally 0mm.
The element #1 position is normally referenced from the front of the wedge
face and for that reason the number is negative. (-69mm below)

33

OmniScan MX2 Training Wedge Parameters Offsets cont.

Question:
What is the affect on the UT data if the primary offset is wrong?
Answer:
The beam exit point is miscalculated by the software and the surface distance
to the indication is incorrect. The offsets are only for determining position
and do not affect focal law calculation. The A-scan is normal and
trigonometry and depth readings are normal.

34

OmniScan MX2 Training Phased Array Wedge Parameters - Offsets

Question:
Is it possible to know the primary offset of element #1 by measuring it on the
probe and wedge?
Answer:
No. The probe elements are not visible through the protective membrane and
the position of element #1 cannot be measured with precision. The offset
position must come from the drawing of the probe married to the wedge.
Close approximations are unacceptable and result in reduced precision.

35

OmniScan MX2 Training Phased Array Calculator Review

What are the essential parameters of 1D linear array

wedge that are required by the OmniScan MX2
software?
1. Wedge model number.
2. Wedge orientation.
3. Height of element #1 on probe.
4. Wedge velocity.
5. Wedge offsets.
Answer: All of the above
36

OmniScan MX2 Training Phased Array Calculator Review

Question:
What are the essential parameters for the phased
array calculator?
1. Probe parameters.
2. Wedge parameters.
3. Material Velocity
4. Beam Formation.
Answer: All of the above.

37