Scribd
Upload
177 views

Programare Cheie VW

This document provides instructions for matching radio-frequency remote controls to Volkswagen and Audi vehicles. It involves using diagnostic procedures to access the central locking or central conversion channel and entering values to store the remote control codes. The procedure involves selecting the appropriate channel, reading and saving the current number of stored remotes, and pressing buttons on the remotes to store them within 15 seconds. It may require clearing existing codes first before matching new remotes.

Uploaded by

Fianu Alexandru
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
177 views

Programare Cheie VW

This document provides instructions for matching radio-frequency remote controls to Volkswagen and Audi vehicles. It involves using diagnostic procedures to access the central locking or central conversion channel and entering values to store the remote control codes. The procedure involves selecting the appropriate channel, reading and saving the current number of stored remotes, and pressing buttons on the remotes to store them within 15 seconds. It may require clearing existing codes first before matching new remotes.

Uploaded by

Fianu Alexandru
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

Procedure for matching radio-frequency remote controls to many VW & Audi vehicle

s:
Check the Ross-Tech Wiki under Diagnostic Procedures for instructions specific t
o your vehicle.
Gather ALL the remotes you would like to match. Insert one key in the ignition a
nd turn it ON.
[Select]
[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car,
as found here)
[Adaptation - 10]
Enter channel "01" (May be channel "21" in some Audi models).
[Read]
This will display the number of currently stored remotes in "Stored Value".
Enter your total number of keys up to a maximum of 4(including any existing keys
) in "New Value"
[Test]
Verify that the number in "Test Value" is correct.
[Save]
Then press and hold (for at least one second) the UNLOCK button on the fob, at w
hich time it will be learned. If you're programming more than one fob press and
hold the UNLOCK button on the second fob for one second, press and hold the UNLO
CK button on the third fob for one second, etc. You have a total of 15 seconds
to do them all.
The car may give you some sort of acknowledgement as each key is learned (lights
flash, horn beep, etc.)
If the above procedure does not work (neither Channel 01 nor Channel 21 are avai
lable), follow this procedure:
Insert a working (old) key in the ignition and turn to the ON position (do not s
tart car).
[Select]
[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car,
as found here)
[Meas. Blocks - 08]
Enter group "003" (may be group "007" in some vehicles)
[Go!]
The value in field 2 shows how many remotes have been matched and in which memor
y positions (for example, "0001" indicates 1 transmitter in position 1).

Lock the car from outside using the new, unmatched key in the driver-side door l
ock. You may need to hold the key in the unlock position while you do the next s
tep.
Press the UNLOCK button on the new key within 5 seconds often enough to reach ne
xt memory position (so, if the value in field 2 was 0001, you should press the n
ew key's unlock button twice, to put the new key in memory position 2)..
The car may give you some sort of acknowledgement as the button is pressed (ligh
ts flash, horn beep, etc.)
Wait 5 seconds and press the unlock button on the new key to unlock the door.
Turn the ignition key to OFF and remove the old key.
Press LOCK and UNLOCK with the new key.
Insert the new key in the ignition and turn to the ON position (do not start car
).
[Select]
[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car,
as found here)
[Meas. Blocks - 08]
Enter group "003"
[Go!]
The value in field 2 should now indicate 0011 in the example used, showing the o
ld key still matched in position 1 and the new key matched in position 2.
Make sure that new keys are always coded into free memory positions (where there
is a zero in Group 003, field 2). If occupied positions (distinguishable by a "
1") are used, the transmitter previously coded to this position will no longer w
ork.
In some cases, it may be necessary to clear out existing matched remotes using t
he following procedure:
[Select]
[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car,
as found here)
[Adaptation - 10]
Enter channel "00"
[Read]
[Save]
When the prompt asks if you are sure you want to save a value of 0 to Channel 00
, click [Yes]
After doing so, no remotes will be matched. You'll need to follow the appropriat

e above procedure to match all of the remotes.

You might also like