Constant Head Permeability Test

CONSTANT HEAD PERMEABILITY TEST
OBJECTIVE:-To calculate the permeability of sandy soil. The permeability

test is a measure of the rate of the flow of water through soil.
THEORY:In 1856 the French engineer Henri Darcy demonstrated by experiment
that it is possible to relate the discharge rate of water flowing from a
soil to the hydraulic or total head gradient in the soil and a property of
the soil which we refer to as the coefficient of permeability or the
hydraulic conductivity.There are two general types of permeability test
methods that are routinely performed in the laboratory: (1) the
constant head test method, and (2) the falling head test method. The
constant head test method is used for permeable soils (k>10-4 cm/s)
and the falling head test is mainly used for less permeable soils (k<10-4
cm/s). ASTM D 2434 - Standard Test Method for Permeability of
Granular Soils (Constant Head).
Q=kiA
The coefficient of permeability(k) is a constant of
proportionality relating to the ease with which a fluid passes through a
porous medium.
1.The two main factors that determine the order of magnitude of the
permeability coefficient are: grain size and cleavage (secondary
interstices).
2.The impact of the factors listed below is inferior, but still not
insignificant:
grain shape and orientation,
quantity and connection of interstices,
uniformity coefficient,
water content and saturation conditions before seepage begins,

the properties of the passing liquid (water),
hydraulic conditions (hydraulic gradient, Reynolds number etc.),
transient phenomena (migration, wash-out and wash-in of grains).
SCOPE:- This property is necessary for the calculation of seepage

through earth dams or under sheet pile walls, the calculation of the
seepage rate from waste storage facilities (landfills, ponds, etc.),and the
calculation of the rate of settlement of clayey soil deposits. The test is
limited to materials which have a coefficient of permeability of
approximately 300 mm/day or greater.
APPARATUS:Permeameter, Tamper, Balance, Scoop, 1000 mL Graduated
cylinders, Watch (or Stopwatch), Thermometer, Filter paper.
PROCEDURE:A. Preparation:1) Obtain the mass of the permeameter.
2) Carefully place and compact the dry soil in the permeameter in 3
to5
layers. Level the top surface of the soil by applying a small
pressure to the porous stone.
3) Measure the height of the compacted soil. This is equal to L for the
computing the total volume of soil.
4) Measure the distance from the top manometer tube to the top of the
bottom porous stone. This is the length L for the falling head test.
5) Measure the mass of the permeameter and the dry soil.
B. Constant Head Permeability Test:1) Assemble the permeameter and attach the manometer tubing to the
side of the permeameter. Attach the tubing from the constant head
supply to the top of the permeameter. Attach the exit tubing to the
bottom of the permeameter and place the other end in the overflow
flask.
2) Open the valves to the permeameter and slowly add water to the
constant head tank to saturate the soil sample.
3) Open the clamps on the manometer tubes.
4) Adjust the rate of flow and allow the flow to reach a stable head
condition, i.e. water levels in the manometer remain constant. Record
the water levels in the manometers as h1 (near the top of the soil) and h2
(near the bottom of the soil).
5) Measure and record the discharge q and the time t.
6) Repeat the steps 3 and 4 two additional times using different values
of h1 and h2 (total head difference), which can be achieved by adjusting
the overflow level of the discharge.
CALCULATION:- Calculate the permeability, using the following
equation:
Where:
k = coefficient of permeability at temperature T, cm/sec.
L = length of specimen in centimeters
t = time for discharge in seconds
Q = volume of discharge in cm3 (assume 1 mL = 1 cm3)
A = cross-sectional area of permeameter (= D2
4 , D= inside diameter of the permeameter)
h = hydraulic head difference across length L, in cm of water; or it is
equal to the vertical distance between the constant funnel head level
and the chamber overflow level.
(h and L are adjusted such that the value of hudraulic gradient equals 1.)
DATA OBSERVED:Weight of cylinder=267 gm
Wt. of cylinder+soil=336 gm
Wt. of soil= 69 gm
69
soil =
=1.757 g/cc
=
2.52.58
8
l
=1
Water discharged
0 ml
0 ml
1.3 ml
3.6 ml
3.7 ml
3.6 ml
time
0(2:10 pm)
30(2:40 pm)
60(3:10 pm)
90(3:40 pm)
120(4:10 pm)
150(4:40 pm)
So, Q =Average of last two discharges

i.e. 3.65 ml
hence, k=4.13 10-4 cm/second
CONCLUSION:Silty sand 10-3 to 10-4
silt is so compactable makes it easier to keep nutrients and

moisture in place for prolonged periods of time. Silt is considered
a good compromise soil between clay and sand, since its weight
and density are in between these two other types of soil.

Constant Head Permeability Test

Uploaded by

Copyright:

Available Formats

Constant Head Permeability Test

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Constant Head Permeability Test

Uploaded by

Copyright:

Available Formats

CONSTANT HEAD PERMEABILITY TEST

OBJECTIVE:-To calculate the permeability of sandy soil. The permeability

water content and saturation conditions before seepage begins,

SCOPE:- This property is necessary for the calculation of seepage

So, Q =Average of last two discharges

silt is so compactable makes it easier to keep nutrients and

You might also like