1

Lightning and Lightning Arrester Simulation

in Electrical Power Distribution Systems
D. Rodriguez-Sanabria, Student Member, IEEE, C. Ramos-Robles, UPRM Graduate Student, L. OramaExclusa, Member, IEEE

Abstract--this paper presents an overview of how ATP/EMTP

can be used to model lightning strikes and their effects on power
distribution systems. Emphasis is given on lightning arrester
action and deployment. This work is the result of a two graduate
students at the University of Puerto Rico-Mayagez

Index Termslightning, power system lightning effects, surge

arresters, ATP, ATPDraw, power system transients, distribution
feeder.

I. NOMENCLATURE
PCC- Point of common coupling
LA-lightning arrester
BIL-basic insulation level
MOV-metal oxide varistor
ATP-Alternative Transient program
EMTP-Electromagnetic Transients Program
LLS-Lightning locating systems
II. INTRODUCTION

ightning is a very impressive phenomenon that occurs in

nature. The amount of energy contained in a lightning
stroke is very high and it can be extremely destructive.
Electric distribution networks are particularly vulnerable to
lightning strokes. A single stroke to a distribution line can be
sufficient to cause a blackout throughout a feeder. To prevent
this, power systems are protected with lightning rods, ground
wires and lightning arresters.
This paper presents the results of simulations completed in
ATP/EMTP that quantify the effects of lightning strikes on a
particular distribution feeder. The paper focuses on the impact
of lightning on power systems and its mitigation by the use of
appropriate surge suppressor deployment.
III. LITERATURE REVIEW
A. Lightning an overview
Lightning is a physical phenomenon that occurs when the
clouds acquire charge or become polarized, so that the electric
fields of considerable strength are created within the cloud
and between the cloud and adjacent masses such as earth and
other clouds, [1]. When these fields become excessive, to the
extent that the dielectric (the air) of intervening space can no

longer support the electrical stress, a breakdown or lightning

flash occurs; this is usually a high-current discharge.
B. Lightning in power systems
Lightning is the main reason for outages in transmission
and distribution lines [1]. The lightning problem is classified
as a transient event. When lightning strikes a power line, it is
like closing a big switch between a large current source and
the power line circuit. The sudden closing of this big switch
causes an abrupt change in the circuit conditions, creating a
transient. There is also the case when the lightning strikes the
vicinity of the power line and the large magnetic field
generated from the lightning current cause mutual coupling
between the power line and the lightning. The event alters the
conditions of the power line circuit, as a result, produce an
electrical transient.
The study of lightning strokes in power lines is very
important because it is known that lightning does strike the
same structure over and again. This can be a very serious
problem for power lines, typically, the highest structures
located in high incidence lightning regions [2]. Any structure,
no matter its size, may be struck by lightning, but the
probability of a structure been struck increases with its height.
Very close dart leaders can make as significant a
contribution as return strokes in inducing voltages and
currents on power systems [3].
C. Lightning Prevention and Suppression Mechanism
Lightning rods are used as prevention mechanisms to avoid
lightning hitting tall buildings or houses where lightning
incidence is high, but no lightning rod can offer absolute
protection, [2]. A lightning rod protection system has three
main parts:
The rods on the top of the protected structure,
The wires which connect the rods together and those
which run down the sides of the structure to the
grounding arrangement,
The grounding arrangement.
Rods can be pointed or ball rounded at the top. The rod
material should be a corrosion-resistance material such as a
copper, aluminum, or galvanized iron.
The wires that connect the rod to the grounding
arrangement have the function of carrying the lightning
current to the ground. The wires in the top of the structure
have the secondary function of intercepting lightning

discharges which may have missed the rods, [2]. The wires
must be well grounded otherwise the lightning current may
jump from the wires into the protected structure in search of a
better ground. Grounding is accomplished by connecting the
wires to long rods which are driven into ground or by
connecting the wires to large buried metallic conductors. The
buried conductors have to be connected to all nearby gas
pipes, water pipes, or other buried metallic pipes or cables.
To protect high voltage transmission lines from lightning,
the metallic rods and wire conductors are replaced by a system
of wires suspended between tall towers arranged around the
structure. These grounded wires are strung above the high
voltage lines to intercept strokes that would otherwise hit the
power lines, [2].
If a lightning stroke hits a power line, the only way to
protect it is using a lightning arrester (LA). The lightning
arrester is a non-linear device that acts as an open circuit to
low potentials, but conducts electrical current at very high
potentials. When lightning strikes a line protected with a
lightning arrester, the non-linear resistance draws the current
to ground.
One of the most common lightning arresters is the MOV
(metal oxide varistor) lightning arrester, [4]. The MOV has a
piece of metal oxide that is joined to the power and grounding
line by a pair of semiconductors. The semiconductors have a
variable resistance dependent on voltage. When the voltage
level in the power line is at the rated voltage for the arrester,
the electrons in the semiconductors flow in a way that creates
a very high resistance. If the voltage level in the power line
exceeds the arrester rated voltage, the electrons behave
differently and create a low resistance path that conducts the
injected lightning current to the ground system.
D. Description of a Lightning Discharge
A lightning discharge is called a flash, [2]. The duration of
a flash is only a few tenths of a second. Cloud to ground
flashes are composed of a single stroke or a multiple number
of component strokes. Multiple stroke flashes have 3 to 4
strokes. The strokes are typically 40 to 50 milliseconds apart.
The typical lightning peak currents measured at ground
range from 10 kA to 20 kA, but occasionally they range up to
hundreds of thousands of amperes, [2]. The peak current is
reached in a few millionths of a second, and then it decreases
terminating in a thousandth of a second or so unless
continuing current flows. It is very common that first stokes
have larger currents that subsequent strokes, but this is not
always true.
Lightning flashes which contain continuing currents are
called hot lightning, [2]. The continuing current lasts for one
or two tenths of a second and have a typical peak value of 100
A. Hot lightning ignites fires. The lightning that does not
contain a continuing current is called cold lightning, [2]. Cold
lightning does not set fires, but it is very destructive.
E. Starting a Lightning
The usual flash between the cloud and the ground is
initiated in the base of the cloud, [2]. The initiating discharge,

a downward traveling spark, is called the stepped leader. The

stepped leader is a low-luminosity traveling spark which
moves from the cloud to the ground in rapid steps about 50
yards long, and lasts less than a millionth of a second. The
formation of each step of a dart-stepped leader is associated
with a charge of a few milli-coulombs and a current of a few
kilo-amperes, [3]. The visible lightning flash occurs when the
stepped leader contacts the ground. The usual stepped leader
starts from the cloud without any knowledge of what
structure or geography are present below. It is thought that
the stepped leader is unaware of objects beneath it until it is
some tens of yards from the eventual strike point. When
awareness occurs, a traveling spark is initiated from the
point to be struck and propagates upward to meet the
downward-moving stepped leader, completing the path to
ground. When the stepped leader reaches ground, the leader
channel first becomes highly luminous at the ground and then
at higher altitudes. The bright, visible channel, or so-called
return stroke, is formed from the ground up, thus visible
lightning moves from the ground to the cloud.
In very tall structures the lightning is result of the reverse
process, [2]. They are initiated by stepped leaders which start
at the building top and propagate upward to the cloud.
F. Characteristics of Lightning
The usual ratio between the median values for field peaks
of the first stroke and the subsequent stroke is 2:1, [5]. Larger
strokes are preceded by longer inter-stroke intervals. The
typical mean flash duration found in the literature is 175 ms.
Since many lightning parameters show a large scatter for
different thunderstorm days, long-term data from lighting
locating systems are more representative of average lightning
compared to data derived from electric field measurements
typically performed during a few thunderstorms.
Lightning parameters are the basis for the design of
lighting protection equipment and for the calculation of
lightning radiated fields and their interaction with power lines,
[5]. There are four different methods to measure lightning
parameters:
Direct current measurements in natural lightning
Direct current measurements in triggered lightning
Measurement of interferences from electric and
magnetic fields
Lightning locating systems
Lightning peak currents is one of the most important
lightning parameters. Almost all of the national and
international standards on lightning protection are based on
lightning current measurements made in Switzerland.
Lightning peak currents are lognormally distributed and
usually described by median value and standard deviation or
by 5, 50, and 95% values (see TABLE 1), [5].

3
TABLE 1. LIGHTNING CURRENT MAGNITUDE DISTRIBUTION

Typically, 51% of all flashes with more than one stroke

contained at least one subsequent stroke with a peak greater
than the peak of the first stroke, [5]. To quantify how much
the peak of one of the subsequent strokes exceeds the peak of
the first stroke in these flashes, the ratio of maximum
subsequent stroke peak field to peak field of the first stroke is
calculated.
Different percentages of single-stroke flashes are reported
in literature. The values range from 14% to 40%. Percentage
of single-strokes flashes vary significantly from storm to
storm (from 30 to 80% with a mean of 40%) and probably
depend on season, type of thunderstorm, etc, [5].
The number of strokes per flash varies due to the location,
season and type of thunderstorm. In Florida, Rakov reported
an average number of strokes per flash to be 4.6 [6]. The
geometric mean of the time interval between strokes is about
33ms to 60 ms. Flash duration is reported to have a median
duration of 180 ms for negative multiple-strokes flashes [7].
First strokes in Austria are different from those in Florida,
consistent with the hypothesis that lightning parameters are
specific for topographic and climatic regions, [5]. The
percentage of single-stroke flashes and the number of strokes
per flash exhibit a considerable variability for the individual
storms even in the same region. Statistical evaluations based
on data for a few storms may, therefore, may not be
representative of the total lightning activity in a region. It is
very important to be aware of possible bias, when data from
only a single storm is analyzed.
G. Lightning Properties
Measurements reveal that the initial electric field peak
(current peak) for the only strokes in single-stroke flashes was
smaller than for first strokes in multiple-stroke flashes, [6].
Half of all flashes, single and multiple-stroke, contact ground
at more than one point, with spatial separation between the
channel terminations being up to many kilometers. One third
of all multiple-stroke flashes had at least one subsequent
stroke whose distance-normalized initial electric field peak
exceeded that of the first stroke in the flash. Contrary to the
implication of most lightning protection and lightning test
standards such flashes are not unusual. Leaders of lower-order
subsequent strokes following previously formed channels
were more likely to show stepping, as opposed to continuous
propagation (i.e., to be dart-stepped leaders rather than dart
leaders), than were leaders of higher-order strokes.
Lower-order subsequent return strokes exhibited a larger
initial electric field peak than did higher-order strokes. The
second leader of the flash (the first subsequent leader)
encounters the least favorable propagation conditions of all

subsequent strokes: more than half of the second leaders either

deflected from the previously formed path to ground or
propagated in a stepped, as opposed to a continuous, fashion
along the lowest part of that path. Inter-stroke intervals
preceding second strokes are similar to or shorter than those
preceding higher-order strokes.
A number of lightning properties derived from electric field
records appear dependent on stroke order, [6].
The majority of long continuing currents (longer than 40
ms) are initiated by subsequent strokes of multiple-stroke
flashes as opposed to either the first stroke in a multiple-stroke
flash or the only stroke in a single-stroke flash, [6]. There
appears to be a pattern in initiating long continuing currents.
Findings regarding the occurrence of single-stroke flashes,
multiple ground strike points, and the relative stroke intensity
within a flash, may have important implications for lightning
protection and lightning test standards, [6].
H. Triggered lightning
Many aspects of the physics of the lightning discharge and
of the interaction of lightning with the objects and systems can
only be properly understood by way of measurements made
on very close lightning, [3]. The probability for a lightning
discharge to strike at or close to a given point of interest on
the Earths surface is very low, even in areas of relatively high
lightning activity. The study of the properties and the effects
of close lightning have been made practical via the use of
artificially initiated lightning, lightning stimulated to occur
between a thundercloud and a designated point on the ground.
The most common technique for triggering lightning
involves the launching of a small rocket attached to a trailing
grounded copper wire in the presence of a sufficiently charged
cloud overhead, [3]. The cloud charge is remotely sensed by
measuring the electric field at ground level, with values of 4
to 10 kV/m usually being good indicators of favorable
conditions for lightning initiations. When the rocket is
typically 200 to 300 m high, the electric field enhancement
near the upper end of the wire is sufficient to trigger a
positively charged (in the most common case of
predominantly negative charge at the bottom of the cloud)
leader extending toward the cloud. The upward leader melts
and vaporizes the trailing wire and establishes a so-called
initial continuous current of the order of some hundred
amperes along the wire trace, which effectively serves to
transport negative charge from the cloud charge source to the
ground via the instrumented triggering facility. After the
cessation of the initial continuous current, several downward
leader/upward return stroke sequences often traverse the same
path to the triggering facility.
The return strokes in triggered lighting are similar to
subsequent return strokes in natural lightning, although the
initial processes in natural and classical triggered lightning are
distinctly different: in natural lightning, a negative downward
stepped leader and ground attachment followed by a first
return stroke versus, in triggered lightning, an upward positive
leader followed by an initial continuous current.
Lightning appears to be able to reduce the grounding
impedance which it initially encounters at the strike point so

that at the time of channel-base current peak the reduced

grounding impedance is always much lower than the
equivalent impedance of the channel, [3].
I. Positive Lightning
Positive lightning discharges have recently attracted
considerable attention for the following reasons, [8]:
The highest recorded lightning currents (up to 300 kA)
and the largest charge transfers to ground (up to
hundreds of coulombs) are associated to positive
lightning
Positive lightning can be the dominant type of cloudto-ground lightning during the cold season and during
the dissipating stage of a thunderstorm.
Positive lightning has been recently identified as a
major source of sprites and elves in the middle and
upper atmosphere.
Reliable identification of positive discharges by
lightning locating systems (LLS) has important
implications for various studies that depend on LLS
data.
Positive flashes are usually composed of a single stroke.
About 80 percent of negative flashes contain two or more
strokes, [8]. Multiple-stroke positive flashes do occur but
they are relatively rare.
Positive return strokes tend to be followed by continuing
currents that typically last for tens to hundreds of
milliseconds, [8]. Electric field measurements show that
continuing currents in positive flashes are in excess of 10 kA,
an order of magnitude larger than for negative flashes, for
periods up to 10 ms. In the winter lightning in Japan directly
measured positive continuing currents in the kilo-amperes to
tens of kilo-amperes range in are seen following the initial
current pulses. Such large continuing currents are probably
responsible for the unusually large charge transfers by positive
flashes.
From electric field records, positive return strokes often
appear to be preceded by significant in-cloud discharge
activity lasting, on average, in excess of 100 ms, [8]. This
suggests that a positive discharge to ground can be initiated by
a branch of an extensive cloud discharge.
LLSs data reveals that the median value of the positive
lightning peak current is found to be greater in the winter than
in the summer, [8]. Median positive peak currents exceeded
40 kA in the Midwest of the U.S., but were less than 10 kA in
Louisiana and Florida. The positive peak current maximum in
the winter lightning in Japan appears to vary during the storm
life cycle reaching the largest value when the stratiform region
is most intense.
It appears that positive cloud-to-ground discharges are
intimately related to positive lightning discharges, [8]. Some
cloud discharge processes are apparently capable of producing
electric and magnetic field signatures resembling those
characteristics of return strokes and of comparable amplitude.
The polarity of these cloud-discharge pulses is probably more
often the same as that expected for positive return strokes. As
a result it is very difficult to identify positive return-stroke
waveforms with confidence.

J. Bipolar Lightning
Lightning current waveforms exhibiting polarity reversals
are denominated bipolar lightning, [8].
Many bipolar
lightning current waveforms have been observed in winter
lightning studies in Japan.
There are basically three types of bipolar lightning
discharges, although some events may belong to more than
one category, [8]:
The first type of bipolar discharges is associated with
a polarity reversal during a slowly-varying
(millisecond-scale) current component, for example
the initial continuous current in object-initiated
lightning or in rocket-triggered lightning. The polarity
reversal may occur one or more times and may
involve an appreciable no-current interval between
opposite polarity portions of the waveform.
The second type of bipolar discharges is characterized
by different polarities of the initial stage current and of
the following return stroke or strokes. The initial
stage current in this waveform is negative and the
return stroke current, followed by a continuing current
is positive.
The third type of bipolar discharges involves return
strokes of opposite polarity. All documented bipolar
discharges in this category (return strokes of opposite
polarity) are of the upward type.
Bipolar lightning discharges are usually initiated by
upward leaders from tall objects, [8]. It appears that positive
and negative charge sources in the cloud are tapped by
different upward branches of the lightning channel.
IV. DEVELOPMENT OF SIMULATION
A. Test System
To assess the impact of lightning strikes on electric power
systems, a test system was assembled using ATPDraw. The
test system is based on the IEEE 34 bus test feeder system [9],
which features three phase balanced and unbalanced loads and
distributed single phase loads. The systems infinite bus is a
69kV connection from the utility. This bus becomes the point
of common coupling (PCC) for a 24.9kV feeder. The original
34 bus IEEE test system featured a 2.5 MVA substation
transformer; this transformer was adjusted to a higher value of
22 MVA, to compensate for additional loads that were going
to be included in the simulation. Per unit impedance values
were kept the same and internal transformer impedance values
were adjusted to the new capacity. The 69kV to 24.9kV
substation transformer and the 24.9kV to 4.16kV transformer
at bus 832 were simulated as a saturable three phase delta-wye
devices based on the standard ATP GENTRAFO model.
Regulating transformers were not included in these
simulations; their impact would be negligible in this kind of
analysis and the added simulation complexity did not justify
the extra precision. For the general system configuration see
figure 1.

Fig. 1: General system configuration

B. Lightning flash
The lightning flash simulated in ATPDraw was based on
the cold lightning flash characteristic described in [2]. The
flash is composed of three sequential spikes of varying
magnitudes. The first strike has a magnitude of 20kA, while
subsequent strokes have magnitudes of 12kA and 9kA
respectively. It was implemented in ATPDraw using three
shunt connected ideal current sources. The first stroke has a
duration of 0.6 ms and is presented figure 3.

System unbalances, including effects due to loads and

unequal phase spacing were included in the simulation, since
they had a noticeable impact on the system operation. All line
parameters, except line 806-808, were included as lumped
series or pi equivalents depending on the way it was
established on the 34 bus IEEE test feeder specification. Line
806-808 was simulated using ATP Line and Cable Constants
(LCC) subroutine using the lines physical configuration
given. This line was simulated using the LCC to consider
mutual inductance between phases. Two LCC modules were
created to simulate the two half-lengths of the line and provide
for a center node in the line. The center node was used to
connect the simulated lightning strike.
All load values, three phase or single phase, were simulated
as constant impedance loads instead of the load model
specified in the IEEE test system specification. This was done
for simulation efficiency and ease of convergence. Single
phase loads were installed following the phase information
stated in the standard. Distributed loads were included in the
following way: distributed loads dispersed through several
buses were divided in equal lump spot loads installed at each
bus along the specified line; if the dispersed loads were
located along a single line segment between two buses, a
single equivalent lump spot load was installed on the far end
of the line. These modifications provided for worst case
formulation of the data. Single phase loads were simulated as
constant impedance loads and integrated into the system as
lumped passive RLC elements with the adequate R, L and C
values for the real and reactive power requirements. Three
phase loads were implemented using the RLC-Y or RLC-)
ATP models. Unbalanced three phase loads were simulated as
specified by the test feeder standard, including phase rotation
and individual phase loading. The feeder configuration as
implemented in ATPDraw is shown in figure 2.

Fig. 3: First lightning stroke 20kA for 0.6ms

This first stroke was simulated using a Type-15 Surge

function. According to the ATP/EMTP Rule Book [10] the
surge function is given by
f ( t ) = amplitude( e At e Bt ) ---- (1)

The constants amplitude, A and B were selected to provide

a surge value of 20kA for a duration of 0.6ms. Constants
values are presented in Table 2.
TABLE 2: TYPE 15 SURGE FUNCTION VALUES

The second and third strokes were implemented using

TYPE-13 ramp functions of 0.3ms duration with 12kA and
9kA magnitude, respectively. Table 3 summarizes the values
used for the functions. Figure 4 shows the simulated lightning
flash as implemented in ATPDraw.
TABLE 3: TYPE 13 RAMP FUNCTION VALUES

Fig. 2: ATPDraw system Configuration

center strike case and two line end cases (node 806 and 808).
Line end cases were added to see the effects of a lightning
strike directly to the loads, while the center cases were
designed to assess the propagation of the induced lightning
surge across the line. Case numbers and descriptions are
specified in table 4.
TABLE 4: CASE LIST AND CASE DESCRIPTIONS

V. DISCUSSION

Fig. 4: Cold Lightning strike as implemented in ATPDraw

For the simulations, lightning makes direct contact with

phase B of line 806-808 at varying locations depending on the
specific case. Phase B was selected since it is the middle
conductor on the line structures, which provides for the
highest induction on the other two phases. Lightning arresters
were simulated in typical locations including load PCCs and
the substation transformers. Lightning arresters used for the
simulation were 30kV, distribution class, rated units.
Lightning arrester characteristics were taken from
manufacturer datasheets [11]. Arrester residual voltage curve
is shown in figure 5.

A. Scenario 1: No lightning arresters

The first scenario of the study simulated direct contact of
the phase B conductor of line 806-808 without any lightning
arresters. As will be presented later in this discussion, impact
is severe. The severity of the lightning flash is enough to
guarantee insulation failure on line structures and damage to
connected equipment; equipment which include the substation
transformer. The voltage levels at the strike point are in excess
of 8000kV for cases without lightning arresters (cases 1-3).
Due to limitations of space, only worst case events are plotted,
other cases produced lower values unless otherwise noted.
Voltage waveform at the strike point for case 1 is shown in
figure 6.

Fig. 6: Voltage at strike location for case 1

Fig. 5: Arrester residual voltage curve

C. Cases
Two different scenarios were analyzed for this study. Each
scenario had several cases with varying contact locations. The
first scenario included cases with no lightning arresters
installed on the loads or on the substations, while the second
scenario provided lightning arresters on the loads and
substations, as typically found in distribution feeders. Three
cases were defined for each scenario. Each scenario had a

It can be observed from the above figure, that first stroke

induced voltages are in the vicinity of 7000kV. Nonetheless,
reflections along the feeder amplify the surge, producing
higher voltages downstream into the feeder. Maximum
voltages for cases 1 to 3 are: 8067kV, 9229kV, and 9231kV
(B840/848, B808, and B806), respectively for phase B
conductors. These values are clearly over insulation flashover
levels for 24.9kV equipment. As expected, phase B
conductors exhibit the worst overvoltages due to direct

impact. One interesting detail that should be emphasized for

these cases is that maximum voltages are present in the
opposite ends of the line for endpoint cases (cases 2 and 3),
but in branch buses 840/848 for the midpoint case 1. Voltages
at the substation are also affected, enough to surpass BIL
levels of the transformer (350kV BIL for 69kV) but lower
than overall maximum overvoltages. Figure 7 presents the
waveforms at the substation. Results from cases 1-3 clearly
indicated that voltage surge mitigation is in order. Figure 8
presents the waveform for buses 840 and 848 for case one
(only phase B shown for simplicity).

for subsequent simulations. Case 4 established the impact

location in the midpoint of line 806-808; it is equivalent to
case 1 but with lightning arresters. The use of lightning
arresters immediately reduces lightning impact on the system.
Overvoltages for case 4 are limited to values in the vicinity of
50kV for the endpoints of the line and 46kV for both
substation and 832 buses. The most impacted buses of case 1,
B848 and B840, show greatly decreased voltage peaks, with
maximum voltage equal to 44.7kV (see figure 9).

Fig. 9: Bus 840/848 waveforms with lightning arresters. Note: Only Phase B
is displayed.
Fig. 7: Substation bus voltage after strike.

These values are well within flashover and BIL ratings of

the feeder equipment (25kV/150kVBIL). Nevertheless,
voltage magnitude at the point of impact is still of
astronomical proportions, namely 5MV (see figure 11).
Magnitudes of this proportion are still able to cause flashover
and surely the destruction of the adjacent distribution poles.
Energy dissipated by the arresters by bus 848 is shown in
figure 12.

Fig. 7: Voltage at buses 840/848

Note that figure 8 presents two waveforms, but one traces

identically the other. These are the worst case voltages for
case 1, namely buses 840 and 848. Values will be used for
comparison with lightning arrester cases.
B. Scenario 2: Lightning Arresters
Initially, simulations were intended to include all typical
lightning arrester installations across a feeder. Unfortunately,
one non-linear device per load across the whole feeder
increased simulation complexity exponentially, as did its
execution time. After several tries, convergence problems and
excessive calculation delays forced the simplification of the
model to allow completion of simulations within a tolerable
time frame. Only lightning arresters in the endpoint buses
(806 and 808), substations and buses 848 and 840 were left

Fig. 11: Midline strike point voltages for case 4

Fig. 12: Lightning arrester dissipated energy bus 848 case 4

As is illustrated in the above plot, maximum energy

dissipation for bus 848 arresters peaks at 2.5kJ. This value is
well within the maximum allowable energy dissipation for the
arrester model [cooper], namely 74.8kJ (max. 3.4kJ/kVUc
where Uc=22kV). A point of concern though, is the energy
dissipation of the arresters in the end buses of the line (see
figure 13).

Cases 5 and 6 were failed attempts at simulating endpoint

strikes on the line with arresters installed. Simulation of both
cases led to convergence problems since voltage surges
produced by direct contact exceeded the maximum operational
voltage of the arresters. Thus, it can be concluded from this
error that the arrester would not survive a direct impact of a
lightning strike of the magnitude simulated (20kA). From case
4 and the partial execution of cases 5 and 6, it can be seen that
a lightning of such magnitude will cause damage to equipment
directly affected by contact but all adjacent equipment
protected by arresters will survive. Thus, the purpose of the
arrester is served for most cases. Realistically, a strike in an
event such as the one simulated would with most probability
be less severe than the strikes simulated in this study, like
stated in table 1.
TABLE 5: MAXIMUM RECORDED VOLTAGES

TABLE 6: MAXIMUM RECORDED VOLTAGES WITH LA

Fig 13: Lightning arrested dissipated energy bus 808 case 4

The plot shown above proves that even though voltages are
being kept at acceptable levels at buses 808 and 806 (bus 806
LA plot not shown, but contain same values of bus 808),
energy dissipation is exceeding maximum total capacity of the
arresters. The plot does seem to indicate, that the arresters
would remain operational until nearing completion the first
stroke. Subsequent strokes most likely will cause arrester
failure. Thus, even though simulations indicate maximum
voltages of 52kV for buses 806/808, this value can be
realistically much higher. This indicates that if such event
could happen in the feeder, higher energy class rated arresters
are required. Otherwise, the LAs must be replaced after an
event of the simulated magnitude. Nevertheless, the arresters
should have dissipated the first and most severe stroke before
failure, most preventing propagation of the highest surges. It
is not unlikely then, that adjacent arresters would dissipate the
additional energy from lesser subsequent discharges without
failure. Maximum voltages across the feeder metered buses
and LA energy dissipation is presented at the end of the
discussion in tables 5 and 6, respectively.

VI. CONCLUSIONS
In this paper, the effects of a lightning strike is presented
and analyzed. A multiple stoke lightning flash was
successfully simulated in ATP. The lightning was used to
investigate the impact of such transient phenomena in a
distribution feeder based upon the IEEE 34 bus test-feeder
configuration. Impact was mitigated using distribution level
surge arresters.
Voltages on buses 806, 808, 832, 840, 848 and the
substation bus were monitored to quantify the effect of a
direct lightning stroke on line 806-808. Several contact points
along line 806-808 were selected to discover the worst case
event.
We can conclude that operating a feeder with no lightning
protection, is very detrimental for system performance. Also,
exposes loads and system devices to unnecessary overvoltages
which may cause insulation flashovers and device failures.
The installation of lightning arresters helps decrease the
adversarial effects resulting of the lightning strike in the
feeder. Our study shows that for certain operating
characteristics of the lightning arrester it can help mitigate one
direct hit multiple-stroke lightning. Nevertheless, the lightning

arresters have to be replaced for several cases, after operation,

due to excessive energy dissipation.
The study successfully establishes the need for lightning
protection systems in distribution feeders. Further research
can be made to identify a different arrester model more
suitable for this feeder.
VII. REFERENCES
[1]
[2]
[3]

[4]

[5]

[6]

[7]
[8]

[9]

[10]
[11]
[12]

[13]

A. Greenwood, Electrical Transients in Power Systems. New York:

John Wiley & Sons, 2nd Ed., 1991, pp. 463-485.
M. A. Uman, All About Lightning. Toronto: Dover, 1986, pp. 1-158.
V. A. Rakov, M. A. Uman, K. J. Rambo, M. I. Fernandez, R. J. Fischer,
G. H. Schnetzer, R. Thottappillil, A. Eybert-Berard, J. P. Berlandis, P.
Lalande, A. Bonamy, P. Laroche and A. Bondiou-Clergerie, "New
Insights into Lightning Processes from Triggered-Lightning Experiments
in Florida and Alabama," Journal of Geophysical Research, vol. 103, no.
D12, pp. 14,117-14,130, June 27, 1998.
J.P. Mackevich, "Proper Lightning Arrester Application Improves
Distribution System Reliability" presented at the IIE 2nd Int. Conf.
Advances in Power System Control, Operation and Management, Hong
Kong, December, 1993.
G. Diendorfer, W. Schulz and V. A. Rakov, "Lightning Characteristics
Based on Data from the Austrian Lightning Locating System," IEEE
Transactions on Electromagnetic Compatibility, vol. 40, no. 4, pp. 452464, November 1998.
V. A. Rakov, M. A. Uman and R. Thottappillil, "Review of lightning
Properties from Electric Field and TV Observations," Journal of
Geophysical Research, vol. 99, no. D5, pp. 10,745-10,750, May 20,
1994.
K. Berger, R.B. Anderson, and H. Kroeninger, Parameters of Lightning
Flashes, Electra, vol. 41, pp. 23-37, 1975.
V. A. Rakov, " Positive and Bipolar Lightning Discharges: A Review,"
Department of Electrical and Computer Engineering, University of
Florida, Gainesville, USA.
Kersting, W.H.; Radial Distribution Test Feeders, Power Engineering
Society Winter Meeting, 2001 IEEE. Volume: 2, 28 Jan.-1 Feb. 2001 pp.
908-912 vol.2
K.V. Leuven EMTP Center, Alternative Transients Program-Rule Book,
Leuven EMTP Center, Belgium, 1987.
Ultrasil Housed VariGap Arresters, Cooper Power Systems Electrical
Apparatus I235-39, April 2003.
V. A. Rakov and M. A. Uman, "Review and Evaluation of Lightning
Return Stroke Models Including Some Aspects of Their Application,"
IEEE Transactions on Electromagnetic Compatibility, vol. 40, no. 4, pp.
403-426, November 1998.
V. A. Rakov, D. E. Crawford, K. J. Rambo, G. H. Schnetzer and M. A.
Uman, "M-Component Mode of Charge Transfer to Ground in Lightning
Discharges," Journal of Geophysical Research, vol. 106, no. D19, pp.
22,817-22,831, October 16, 2001.

VIII. BIOGRAPHIES
Doeg Rodriguez-Sanabria is from Dorado, Puerto
Rico. He is a graduate student at the university of
Puerto Rico-Mayagez, where he will attain a MSEE
on May 2004.

Carlos Ramos-Robles is from Ponce, Puerto Rico.

He is a graduate student at the university of Puerto
Rico-Mayagez, where he will attain a MSEE on May
2004.