A320 INDICATING / RECORDING SYSTEMS | 1.31.00 Pal cnew or CONTENTS SEQ 001 REV 23 31.00 31.05 31.10 31.15 31.20 31.25 31.27 31.30 CONTENTS EIS GENERAL —INTRODUCTION......... - COCKPIT ARRANGEMENT . . —ARCHITECTURE............ —CONTROLS AND SWITCHING . . . —RECONFIGURING THE DMC . —RECONFIGURING DUs..... oaanso ECAM DESCRIPTION —ECAM DU ARRANGEMENT ... . -COLOR CODE ............. — WARNING / CAUTION CLASSIFICATION . — PRIORITY RULES . — TYPES OF FAILURES — AURAL INDICATORS . . RWONN= INDICATIONS ON E/WD — GENERAL — INDEPENDENT FAILURE ... — PRIMARY AND SECONDARY FAILURE . —FLIGHT PHASES . . — MEMOS — CONFIGURATION WARNINGS . GRONN= INDICATIONS ON SD — GENERAL — SYSTEM PAGES . — STATUS PAGE . — PERMANENT DAI aaas ECAM SEQUENCE —GENERAL. . — EXAMPLE . OEB REMINDER < —GENERAL.... — DESCRIPTION . — ARCHITECTURE . . ECAM CONTROLS —ECAM CONTROL PANEL ... — SWITCHING PANEL . . — ATTENTION GETTERS . sIMU_ F.P.S.3 UP for training only STD 13.1@ 8320 INDICATING / RECORDING SYSTEMS | 1.31.00 P2 CONTENTS SEQ 001 REV 33 31.40 31.45 31.50 31.55 31.60 31.65 INDICATIONS ON PFD —GENERAL....... — SPECIFIC GROUND INDICATIONS —ATTITUDE DATA. . —AIRSPEED . — ALTITUDE . : = VERTICAL SPEED . — HEADING —FLIGHT PATH VECTOR . = GUIDANCE ae — TRAJECTORY DEVIATION .... —FLIGHT MODE ANNUNCIATOR ......... ALTITUDE ALERT 00.2... es cece ee bene eee —FLAGS AND MESSAGES DISPLAYED ON PFD........ . 26 —TCAS (refer to 1.34) < INDICATIONS ON ND GENERAL... . ROSE MODES . —ROSE ILS MODE tenes -ROSE VOR MODE ........ ROSE NAV MODE/ ARC MODE -PLAN MODE..........05 : WEATHER RADAR ........... — PREDICTIVE WINDSHEAR SYSTEM < -EGPWS Joo. cece eee eee : —FLAGS AND MESSAGES DISPLAYED ON ND .. . —TCAS (refer to 1.34) < EFIS CONTROLS —EFIS CONTROL PANEL ee — OTHER EFIS CONTROLS .... eee —CHRONOMETER .. CLOCKS — GENERAL — CONTROLS AND INDICATORS . FLT RECORDERS — FLIGHT DATA RECORDING SYSTEM .. . —CONTROLS AND INDICATORS....... : — AIRCRAFT INTEGRATED DATA SYSTEM 4... . WEIGHT AND BALANCE SYSTEM <1 — DESCRIPTION . — CONTROLS AND INDICATORS . sIMU F. P.S.3 UP for training carly STD 13.1A320 INDICATING / RECORDING SYSTEMS | 1.31.00 Es UGHT GREW OPERATING MANUAL CONTENTS SEQ 001 | REV 26 31.67 FLIGHT NUMBER REMINDER < 31.68 TIMER < 31.70 WARNINGS AND CAUTIONS 31.75 ELECTRICAL SUPPLY sIMU_ F.P.S.3 UP for training only STD 13.1Ren INDICATING/RECORDING SYSTEMS | 1.31.05 P41 cnew or EIS - GENERAL SEQ 001 | REV 36 FLIGHT CREW OPERATING MANUAL INTRODUCTION The Electronic Instrument System (EIS) presents data on six identical Display Units (DUs): — The Electronic Flight Instrument System (EFIS) displays mostly flight parameters and navigation data on the Primary Flight Displays (PFDs) and Navigation Displays (NDs). — The Electronic Centralized Aircraft Monitor (ECAM) presents data on the Engine/Warning Display (E/WD) and System Display (SD) : « Primary engine indications, fuel quantity, flap and slat position - Warning and caution alerts, or memos - Synoptic diagrams of aircraft systems, and status messages » Permanent flight data COCKPIT ARRANGEMENT CAPTAIN: FIRST OFFICER : EFIS CONTROL. PANEL- EFIS CONTROL PANEL. NAVIGATION DISPLA\ NAVIGATION DISPLAY INASTER WARNING AND CAUTION LIGHTS! MASTER WARNING AND CAUTION LIGHTS PRIMARY FLIGHT. PRIMARY FLIGHT DISPLAY DISPLAY LLouDsPEAKER ENGINE/WARNING DISPLAY. LounsPeaKeR SYSTEM DISPLAY SWITCHING PANEL, CAM CONTROL PANEL, NFCS~01-3105-001-A0018A, sIMU_ F.P.S.3 UP for training only STD 13.1OQ INDICATING/RECORDING SYSTEMS 1.31.05 P2 ‘etaaton EIS - GENERAL SEQ 001 | REV 23 ARCHITECTURE DISPLAY UNIT (DU) The instrument panels have six identical units. These DUs are full-color cathode ray tubes. DISPLAY MANAGEMENT COMPUTER (DMC) Three identical display management computers acquire and process all the signals received from sensors and other computers to generate the images to be displayed on the primary flight displays, navigation displays, engine/warning display, and system display. Each DMC has two independent channels an EFIS channel and an ECAM channel and is able to drive simultaneously one PFD, one ND, and either of the ECAMs in its engine warning or system status task, SYSTEM DATA ACQUISITION CONCENTRATOR (SDAC) The two identical SDACs acquire data, then generate signals, Some of these signals go to the three DMCs, which use them to generate displays of system pages and engines parameters, Others go to the flight warning computers, which use them to generate ECAM messages and aural alerts. FLIGHT WARNING COMPUTER (FWC) The two identical FWCs generate alert messages, memos, aural alerts, and synthetic voice messages. For this purpose they acquire data : — directly from aircraft sensors or systems to generate red warnings. — through the SDACs to generate amber cautions. The ECAM display units display the alert messages generated by the FWCs. The FWCs also generate. — radio altitude callouts. — decision height callouts. — landing distance and landing speed increments. ATTENTION-GETTERS The FWCs also drive the attention-getters. Each pilot has a set of these on the panel under the glareshield. They are : — a master warning light that flashes “MASTER WARN” in red for red warnings — a master caution light that flashes “MASTER CAUT” in amber for amber cautions SIMU F.P.S.3 UP for training only STD 13.1A320 INDICATING/RECORDING SYSTEMS 1.31.05 P3 EIS - GENERAL SEQ FLIGHT CREW OPERATING MANUAL 001 | REV 28 LOUDSPEAKER The communications loudspeakers announce aural alerts and voice messages, and do so even when they are turned off. R EIS BLOCK DIAGRAM (ers 1 Eris 2)| PFD ND ECAM ND PFD 1 1 but 2 2 LLL uz WARN] cauT| DMC 1 | DMC 3 DMC 2 uu FWC 1 Fwe 2 SDAC 1 SDAC 2 NF C5~01-3105-003-A001AA =] | A/C SYSTENS SENSORS | TNpurs For: | = RED WARNINGS: | 7 SYSTEM PAGES = FLIGHT PHASE |= eNO INFO ‘A/C SYSTEMS SENSORS INPUTS FOR = ~~ AMBER CAUTIONS SYSTEM PAGES sIMU_ F.P.S.3 UP for training only STD 13.1OQ INDICATING/RECORDING SYSTEMS 1.31.05 P4 LGHT CREW OPERATING MANUAL Els - GENERAL SEQ 001 | REV 36 CONTROLS AND SWITCHING ECAM CONTROL PANEL (ECP} The ECAM Control Panel, located on the pedestal, includes : — Such E/WD controls, as CLR, STS, and the brightness control knob. — Such SD controls, as ENG, BLEED, PRESS..., system page selector, and the brightness control knob. EIS DMC SWITCHING SELECTOR A switch near the center of the SWITCHING panel which is located just above the ECAM control panel, enables the flight crew to replace the Captain or First Officer's Display Management Computer (DMC 1, or DMC 2) by DMC 3. ECAM/ND SWITCHING A switch on the right-hand side of the SWITCHING panel enables the flight crew to transfer the ECAM System Display to either the Captain or First Officer's Navigation Display. EFIS SWITCHING A PFD/ND XFR pushbutton on each side console enables the pilot to swap displays to the respective onside DUs. SIMU F.P.S.3 UP for training only STD 13.1A320 pas EIS - GENERAL SEQ 001 | REV 32 INDICATING/RECORDING SYSTEMS. 1.31.05 PS RECONFIGURING THE DISPLAY MANAGEMENT COMPUTER (DMC) In normal operation : — DMC 1 supplies data to the Captain's PFD and ND, and the upper ECAM DU. — DMC 2 supplies data to the First Officer's PFD and ND, and the lower ECAM DU. — DMC 3 is on standby. If a DMC fails (corresponding DU shows a diagonal line), the flight crew can replace DMC 1 or 2 with DMC 3 by turning the EIS DMC switch on the SWITCHING panel to “CAPT 3” or “F/O 3". RECONFIGURING DISPLAY UNITS (DUs) FAILURE OF UPPER ECAM DU (OR CTL/BRIGHTNESS KNOB TURNED TO OFF) If the upper ECAM display fails, or is switched off — The engine/warning page automatically replaces the system/status page on the lower ECAM DU. The flight crew can have the system/status page displayed by — Using the “ECAM/ND XFR” switch, on the SWITCHING panel, to move it to a navigation display unit (NDU), or R — — Pushing and holding (for a maximum of 3 minutes) the related system page pushbutton on the ECAM control panel to temporarily display it on the lower ECAM DU (in place of the engine/warning page). FAILURE OF LOWER ECAM DU (OR CTL/BRIGHTNESS KNOB TURNED TO OFF) If the lower ECAM display fails, or is switched off, the flight crew can display the system/status page by : — Using the “ECAM/ND XFR” switch, on the SWITCHING panel, to display it on NDU, or R — — Pushing and holding (for a maximum of 3 minutes) the related system page pushbutton, on the ECAM control panel to temporarily display it on the upper ECAM DU (in place of the engine/warning page). FAILURE OF BOTH ECAM DUs If both ECAM displays fail, the flight crew may : — Use the “ECAM/ND XFR” on the SWITCHING panel to display the engineAwarning page R on a navigation display and, if needed, R — — Push and hold (for a maximum of 3 minutes) the related system page pushbutton on the ECAM control panel, to temporarily display the system/status page on an ND. sIMU_ F.P.S.3 UP for training only STD 13.1@ 8320 INDICATING/RECORDING SYSTEMS EIS - GENERAL 1.31.05 P6 SEQ 001 | REV 26 PFDU/NDU RECONFIGURATION If a PFDU fails, the system automatically transfers the PFD image to the NDU. The pilot can also m ake this transfer manually by : turing the PED ON-OFF/brightness control OFF, or — pressing the PFD/ND/XFR pushbutton, which cross-changes the images between the PFDU and the NDI IU, If an NDU fails, the pilot can use the PFD/ND/XFR pushbutton to transfer the ND image to the PFDU. DU RECONFIGURATION PFDU1 FAILED NFC5~01-5105-006-A001AA | \ y" DU FAILED | —— | E/W AND S7D FATLED E/W AND S/D FAILED 9 Lo ECNWND XFR i Or —=5 PFDU2 FAILED I i PFD/ND ©) SIMU F.P.S.3 UP for training only STD 13.1A320 INDICATING/RECORDING SYSTEMS. ECAM DESCRIPTION 1.31.10 Pal SEQ 001 REV 23 ECAM DU ARRANGEMENT The ECAM has two display units : — one for the engine/warning display (E/WD). — one for the system/status display (SD). Engine / warning display ENGINE control indication Total FUEL FLAPS / SLATS position NEMO = REMINDER OF FUNCTIONS TEMPORARILY USED SYSTEM SYNOPTICS ‘CORRESPONDING TO: = WARNING/ CAUTION SITUATION = ADVISORY SITUATION = CREW MANUAL SELECTION = CURRENT FLIGHT PHASE NFC5-01-3110-001-A001AA, MEMO or be WARNING / CAUTION messages System display SYSTEM synoptics or STATUS Tar 5 705500 Ks Sar 56 25456 WARNING/CAUTION MESSAGES = TITLE OF THE FAILURE — CORRESPONDING PROCEDURES (ACTIONS TO BE PERFORMED) STATUS OPERATIONAL STATUS OF THE AIRCRAFT AFTER FAILURE INCLUDING RECOVERY PROCEDURES PERMANENT DATA - TAT = SAT = uTc - GW sIMU_ F.P.S.3 UP for training only STD 13.1@ 4320 INDICATING/RECORDING SYSTEMS | 1.31.10 P2 ECAM DESCRIPTION SEQ 001 | REV 35 COLOR CODE The ECAM di indication. RED AMBER GREEN WHITE BLUE MAGENTA : lisplay uses a color code that indicates the importance of the failure or the : The configuration or failure requires immediate action. : The flight crew should be aware of the configuration or failure, but need not take immediate action. : The item is operating normally. : These titles and remarks guide the flight crew, as they execute various procedures, : These are actions to be carried out, or limitations. These are particular messages that apply to particular pieces of equipment or situations (inhibition messages, for example). WARNING/CAUTION CLASSIFICATION LEVEL SIGNIFICATION AURAL VISUAL, FAILURE MODE | Level 3 [Red waming : The configuration, or | Continuous — MASTER WARN failure requires immediate action Repetitive Chime | light red flashing or — Aircraft in dangerous configuration, or | (CRC) or specific | specific red light limit fight conditions (eg: stall, sound or — Waming message /speed) synthetic voice | (red) on EAD. — System failure altering flight safety = Automatic call of (eg : Eng fire, excess cab alt) the relevant system page on the S/D * Level 2 | Amber caution = ‘Single Chime |— MASTER CAUT The flight crew should be aware of the | (SC) light amber steady configuration or failure, but does not Caution message need to take any immediate action. (amber) on EW However, time and situation permitting, ~ Automatic call of these cautions should be considered the relevant system without delay to prevent any further page on the S/D * . degradation of the affected system : — System failure without any direct consequence on the fiight safety (eg: HYD G SYS LO PR) Tevel 1 | Amber caution : Requires crew NONE — Caution message monitoring (amber) on E/WD ~ Failures leading to a loss of generally without redundancy or system degradation procedure, (eg : FCDC fault) INFORMATION | ADVISORY | System parameters monitoring NONE — Automatic call of the relevant system page on the $/D. The affected parameter pulses green, MEMO | Information : Recalls normal or NONE — Green, Amber, or automatic selection of functions which Magenta message are temporarily used on * except in some cases sIMU F. for training only STD 13.1A320 INDICATING/RECORDING SYSTEMS. ECAM DESCRIPTION 1.31.10 Es SEQ 001 REV 23 PRIORITY RULES caution. There are three priority levels for warnings and cautions : — A level 3 warning has priority over a level 2 caution which has priority over a level 1 The FWC observes these priorities. TYPES OF FAILURES Independent : a failure that affects an isolated system or item of equipment without degrading the performance of others in the aircraft. Primary _: a failure of a system or an item of equipment that costs the aircraft the use of other systems or items of equipment. Secondary: the loss of a system or an item of equipment resulting from a primary failure. sIMU_ F.P.S.3 UP for training only STD 13.1@ 8320 INDICATING/RECORDING SYSTEMS ECAM DESCRIPTION 1.31.10 P4 SEQ 400 | REV 38 AURAL INDICATORS (synthetic voice) detected caution message WARNING SIGNAL CONDITION DURATION SILENCING = CONTINUOUS Press * REPETITIVE CHIME iis Mailalohll MASTER WARN t: SINGLE CHIME AMBER CAUTION, 05 seconds AP DISCONNECTION Second push on 1.5 seconds Paver enrecp [2 STAKE OVER pb TAKE OER pb A DISCONNECTION PERMANENT MASTER WARN t: or TAKE OVER pb Tanding capability downgrade or “GPS TRIPLE CLICK PRIMARY LOST” 05 sec. (3 pulses) in approach, or made reversion CRICKET + STALL tnessoge STALL PERMANENT NIL (synthetic voice) CABIN CALL 3 seconds Ni 7 seconds REPEATED BuzzER EMER CABIN CALL nds FE NL 5 ‘As Tong as outside MECH CALL oo ou NIL CONTINUOUS Press 7 SELCAL CALL PERMANENT oe “WINDSHEAR™ (ethene aie) WINDSHEAR REPEATED 3 TIMES NIL ” GO AROUND Windshear ahead WINDSHEAR AHEAD” | detected during the PERMANENT NIL ( synthetic voice) landing phase Windshear ahead "WINDSHEAR AHEAD” detected during the PERMANENT NL (twice) (synthetic voice) | Stored uring. "MONITOR RADAR DISPLAY” ae eee PERMANENT NIL * The pilot can cancel any aural warning, by pressing the : — EMER CANC pushbutton on the ECAM control panel, or — MASTER WARN pushbutton, except for OVERSPEED or L/G NOT DOWN warnings. ** The pilot can cancel the continuous buzzer, by pressing the MASTER CAUT pushbutton, *** When the flight crew presses the MASTER WARN pushbutton (following a warning that leads to an AP disconnection), the Cavalry Charge sound is only inhibited when it has been emitted, in order to avoid an unintended cancellation. SIMU F.P.S.3 UP for training only STD 13.1Fen INDICATING/RECORDING SYSTEMS | 1.31.10 5 ee me ns nansn. ECAM DESCRIPTION sea 200 | REV 31 R WARNING SIGNAL CONDITION DURATION SILENCING * T.5 seconds new ALTITUDE ALTITUDE ALERT ¢ CHORD or selection or press Casi PERMANENT. MASTER WARN pb AUTO CALL OUT ANNOUNCEMENT lu UI (synthetic voice) BELOW 2500 FT PERMANENT NIL (Reter to 1.34.10) GROUND PROXIMITY WARNING (Refer to 1.34.70) PERMANENT NL (synthetic voice) “PRIORITY LEFT" "PRIORITY RIGHT’ | AVP TAKE OVER pb 1 second NIL (synthetic voice) ceva TINTOLE POSITION PERMANENT THRUST LEVER (synthetic voice) Fa ANSING CAS (Refer to 1.34.80) PERMANENT NIL (synthetic voice) a | Current thrust is not ‘SPEED, SPEED, SPEED” sufficient to recover a | Every 5 seconds until THRUST LEVER(s) (Synthetic voice) | positive flight through } thrust is increased pitch control “DUAL INPUT” Both sidesticks are (synthetic voice) | moved simultaneously | __Fvery § seconds [One sidestick deactivated * — The pilot can cancel any aural warning by pressing : — The EMER CANC pushbutton on the ECAM control panel, — The MASTER WARN pushbutton, except for OVERSPEED or L/G NOT DOWN warnings. sIMU_ F.P.S.3 UP for training only STD 13.127 Fen INDICATING/RECORDING SYSTEMS | 1.31.15 Pi eee INDICATIONS ON E/WD SEQ 001 | REV 26 GENERAL The E/WD appears on the upper ECAM display unit (DU). — The upper part of this DU displays : - Engine parameters (refer to 1.70.90) - Fuel on board (FOB) (refer to 1.28.20) - Position of slats and flaps (refer to 1.27.40) — The lower part of this DU displays messages generated by the FWC : - Warning and caution messages when a failure occurs - Memos when there is no failure of nt \ ENGINE (eral \(@2) a FUEL PARAMETERS (e a(S | ucoxe—#— «INDICATION wom “\ ca [se \ ‘SLATS/FLAPS < 96.0 ——s70 | Gur INDICATION 3 1900 — 1500 | : ECAM 5 MESSAGES The lower part, which is dedicated to ECAM messages, is divided into two parts of several lines each. Left part: — Primary or independent warnings and cautions, or — Memo information Right part : — Title of system affected by a primary or independent warming or caution in case of overflow on the left part, or — Secondary failure, or — Memo, or — Special lines (such as “AP OFF”, “LAND ASAP”) As soon as the FWC detects a failure, and if there is no flight phase inhibition active, the EMD displays the title of the failure and actions to be taken. The action line clears automatically when the flight crew has executed the required action. Note : Certain actions will not disappear after execution. sIMU_ F.P.S.3 UP for training only STD 13.1or INDICATING/RECORDING SYSTEMS | 1.31.15 P2 onew or INDICATIONS ON E/WD SEQ 001 | REV 32 INDEPENDENT FAILURE : Ww. INDEPENDENT |} = FAILURE HYD B RSVR OVHT ELEC + Name of the 3 CAMBER OR RED) -;-®— BLUE ELEC PUMP... system affected ce by a failure. 8 Displayed here a in case of . overflow of the ° left part 5 _______ (anber or red) 8 ACTION LINE OVERFLOW SYMBOL, 5 (BLUE) (GREEN) If there are too many ECAM messages for the amount of space available in the lower part of the E/WD, a green arrow appears at the bottom of the display, pointing down to show that the information has overflowed off the screen. The pilot can scroll down to view additional messages by pushing the CLR pushbutton on the ECAM control panel (on the pedestal, just below the lower ECAM DU). PRIMARY and SECONDARY FAILURE wa i PRIMARY {_———__ FAILURE —— =" ELEC * F/CTL = CAMBER OR RED) = AIR DATA SW. F/O 3] * FUEL 8 -CHECK | * CAB PRESS i * BRAKES : ACTION LINE ‘SECONDARY FAILURES : (BLUE) CAMBER) The ECAM DU displays a primary failure as a boxed title. It identifies a secondary failure by putting a star in front of the title of the affected system. Note : The DU displays the overflow symbol, if primary or secondary failures overflow. In case of ELEC EMER CONFIG, the secondary failures are inhibited. sIMU_ F.P.S.3 UP for training only STD 13.1Fen INDICATING/RECORDING SYSTEMS | 1.31.15 P 3 Prey INDICATIONS ON E/WD SEQ 001 | REV 23 FLIGHT PHASES GENERAL The FWC divides its functions according to these ten flight phases : . & i SE 3 @ oso: be oO E 28 é eg . HF 3 3 f oe ee ( ' Fo 2 € & ed 8 8 8 5 ; ' zg 8 g 5 : 1 2 3 4 5 6 7 8 9 10 To improve its operational efficacy, the computer inhibits some warnings and cautions for certain flight phases. It does so to avoid alerting the pilots unnecessarily at times when they have high workloads, such as during takeoff or landing. In these two phases, the DU displays magenta memos : “T.O. INHIBIT” (flight phases 3, 4, and 5), and “LDG INHIBIT” (flight phases 7 and 8). Note : These flight phases are different from and independent of the ones that the FMGC uses, FLIGHT PHASE INHIBITION Two cases are possible (for instance) : @ @ _ FAILURE APPEARANCE {4 1 z 3 4 [5% FLIGHT PHASES INHIBITION ‘waiBiTED PHASE Effect on E/WD : ® The failure occurs during phase 1. The E/WD displays the warning immediately and continues to display it as long as the failure is present, even in phase 2. © The failure occurs during phase 2. The E/WD displays the warning only when the aircraft has entered phase 3, where it is not inhibited. Then the warning remains displayed as long as the failure is present. sIMU_ F.P.S.3 UP for training only STD 13.10 INDICATING/RECORDING SYSTEMS | 1.31.15 P 4 Oe INDICATIONS ON £/WD SEQ 105 | REV 33 R MEMOS DISPLAY Memos appear in the lower part of the E/WD. They are normally in green, but may be amber in abnormal situations, Memos list functions or systems that are temporarily used in normal operations. Each chapter of the “Warning and Cautions” section of this manual lists memo messages. TO AND LDG MEMOS During the takeoff and landing phases, the right side of the memo area displays specific T.0. INHIBIT or LDG INHIBIT (magenta) memos. Takeoff and landing memos are displayed, as follows, during the related flight phases : GREEN BLUE, AS LONG AS ACTION NOT PERFORMED; DISAPPEARS WHEN ACTION a ae BLUE, IF ACTION IS NOT Di GREEN GHEN ACTION TS. PeRPORMED THE TO MEMO APPEARS: BIN AFTER SECOND ENG START, BrovaneD AT LEAST ONE ENGINE IS RUNNING WHEN TO CON TEST PB IS PRESSED. IT DISAPPEARS AT TO POWER APPLICATION. NFCS-01-3115-004-A 10544 * This line disappears when the test is completed. It is replaced by “TO CONFIG NORMAL’, if aircraft configuration is correct. The test is requested again, if the configuration becomes abnormal. THE LDG MEMO APPEARS BELOW 2000Ft. IT DISAPPEARS AFTER TOUCH DOWN (80K). NFe5-01-3115-006-B1058A * “CONF 3” is displayed in alternate or direct law, or if the GPWS LDG FLAP 3 pushbutton is ON. sIMU_ F.P.S.3 UP for training only STD 13.1A320 — INDICATIONS ON E/WD SEQ 100 | REV 23 INDICATING/RECORDING SYSTEMS. 1.31.15 PS CONFIGURATION WARNINGS The following warnings and cautions appear in the lower part of the E/WD if the aircraft is not in takeoff configuration when the pilot presses the T.0. CONFIG pushbutton on the ECAM control panel or applies takeoff power. WARNINGS/CAUTIONS TO CONFIG TEST TO POWER ‘SLATS/FLAPS NOT IN TO CONFIG (R) PITCH TRIM NOT IN TO RANGE (R) RUD TRIM. Nor ne aan ) TRIGGERED NOT RETRACTED (R) TRIGGERED SIDESTICK FAULT (R) (BY TAKE OVER) BRAKES HOT (A) DOORS (A) PARK BRAKE ON (R) FLEX TEMP NOT SET (A) NOT TRIGGERED (R) Red warning {A) Amber caution sIMU_ F.P.S.3 UP for training only STD 13.1A320 INDICATING/RECORDING SYSTEMS. INDICATIONS ON SD 1.31.20 Pal SEQ 100 REV 26 GENERAL — the status page. SYSTEM PAGES The lower ECAM DU can display 12 system pages : (For description see relevant FCOM chapter). — ENGINE (secondary engine parameters) — BLEED (air bleed) — CAB PRESS (cabin pressurization) — ELEC (electric power) — HYD (hydraulic) — FUEL (fuel) — APU (auxiliary power unit) — COND (air conditioning) — DOOR/OXY (doors/oxygen) — WHEEL (landing gear, braking, ground spoilers, etc.) — F/CTL (flight controls) — CRUISE (cruise) The system/status display (SD) uses the lower ECAM DU to display : — pages showing synoptic diagrams of the aircraft systems, or sIMU_ F.P.S.3 UP for training only STD 13.1or INDICATING/RECORDING SYSTEMS | 1.31.20 P2 oer INDICATIONS ON SD SEQ 001 | REV 33 The pilot may manually call up a system page for display on the lower ECAM DU, or the ‘system may automatically display a page. — Manual : + The pilot can use the pushbutton on the ECAM control panel to call up any system page, except the CRUISE page, for display at any time. - The corresponding pushbutton on the ECAM control panel lights up. -A failure-related or advisory display automatically replaces a page the pilot has manually called up. — Automatic, related to a failure : - The relevant system page automatically appears, as soon as any fault or malfunction triggers a caution or warning message. — Automatic, advisory : The relevant system page automatically appears, when a parameter drifts out of its normal range. - The value (shown in green) pulses, as long as it is outside its limits. + The advisory mode is inhibited in some flight phases. Tar ewe sar 8 °C NFC5~01-5120-002-A001AA Note : If an advisory is triggered when the ECAM is in the single-display configuration, an ~~~ advisory message appears on the upper part of the E/WD, and the associated key on the ECAM control panel flashes to identify the appropriate system page. (@]—<——— ADVISORY MESSAGE sIMU_ F.P.S.3 UP for training only STD 13.1Fen INDICATING/RECORDING SYSTEMS | 1.31.20 P3 men INDICATIONS ON SD SEQ 100 | REV 28 FLIGHT CREW OPERATING MANUAL — Automatic, flight phase mode - If no other mode is engaged, the SD displays the system page related to the present flight phase, as shown in the following diagram. FCAS-01-3120-005-A 10004 Phase 2 : The F/CTL page replaces the WHEEL page for 20 seconds when either pilot moves his sidestick (more than 3° in pitch or roll) or when the rudder pedal deflection is more than 22°. - The APU page appears when the APU MASTER switch is ON. It disappears when APU RPM has been above 95 % for 10 seconds, or when the APU MASTER switch is switched OFF. - The ENGINE page appears at the beginning of start sequence or when a pilot selects “CRANK’. It disappears 10 seconds after the end of the start sequence, when the ENG MODE sel is set to NORM. For a description of the ENGINE and AIR indications that appear when the SD is displaying the CRUISE page, see the relevant FCOM chapter. F.useo 0670.9 1sa0 fg 1560 vis_(ne) ENGINE vis_ an) | 1.2713 on 15 — gp 15 AIR cB WS FI/MN a AP 6.6 PST 5] we at 250 | 2 1 23 2 aN (cag ALT FT 4150 U1 SOB00 KE NFe5~01-3120-003-B 10044 sIMU_ F.P.S.3 UP for training only STD 13.1or INDICATING/RECORDING SYSTEMS | 1.31.20 P4 oer INDICATIONS ON SD SEQ 001 | REV 24 STATUS PAGE NF C5~01-3120-004-A001AA The status page displays an operational summary of the aircraft status after the SD has displayed a failure. As shown in the illustration above, the summary includes : @ Limitations (speed, flight level) : Blue @® Approach procedures : White/Red or Amber @ Procedures (corrections to apply for landing) : Blue @ Information : Green @ Cancelled caution : White © Inoperative system : Amber @ Maintenance status : White @® Symbol displayed if data overflows the left or right area. The pilot scrolls the display to view overflow by pressing the CLR pushbutton. Note : The titles of the different parts of the display are white and underlined. sIMU_ F.P.S.3 UP for training only STD 13.1Ren INDICATING/RECORDING SYSTEMS | 1.31.20 P5 cnew or INDICATIONS ON SD SEQ 200 | REV 36 FLIGHT CREW OPERATING MANUAL The STATUS page automatically appears, once the crew has cleared all the pages corresponding to the current failure. The STATUS page also appears automatically during descent, when the slats are extended, unless if the page is empty. The pilot may manually call up the status page by pressing the STS key on the ECAM control panel. If the STATUS page holds messages other than “CANCELLED CAUTION”, or the MAINTENANCE part, the EMD screen shows “STS” (status reminder). If the STATUS page holds messages in the MAINTENANCE part on engine shutdown, the “STS” (status reminder) flashes on the E/WD screen. The screen displays the MAINTENANCE, only when the aircraft is on ground, before engine start-up or after engine shutdown (Phases 1 and 10). PERMANENT DATA @ TAT - 5° Pat set 120m] GW 66000K6 + sat~ 30°C 23H56 : “TAT” (Total Air Temperature) and “SAT” (Static Air Temperature) are displayed in green. @ Temperature @ G LOAD - ALT SEL The screen displays either one of the two items : — Load factor (G LOAD) in amber, when the value is above 1.4 g or, below 0.7 g. This display is inhibited during flight phases 1 and 2. — Altitude selected through the flight control unit, in green, if the flight crew has selected metric units, when the load factor is not displayed. @ ute The screen displays the Universal Time Coordinated (UTC), synchronized with the cockpit clock, in green. © aw R The screen displays the gross weight (GW) in green, as soon as the first engine is started, The last two digits are dashed, if accuracy is degraded. On ground, the indication is replaced by blue dashes, if no computed data is available. sIMU_ F.P.S.3 UP for training only STD 13.1A320 @ INDICATING/RECORDING SYSTEMS 1.31.20 P6 oer INDICATIONS ON SD SEQ 001 | REV 23 LEFT INTENTIONALLY BLANK SIMU F.P.S.3 UP for training only STD 13.14320 UGHT GREW OPERATING MANUAL INDICATING/RECORDING SYSTEMS ECAM SEQUENCE 1.31.25 P41 SEQ 001 REV 26 GENERAL If ECAM detects a failure : — The E/WD displays warning or caution messages. — The master warning or master caution lights light up (except in the case of a level 1 caution). — The system sounds an aural signal (except in the case of a level 1 caution). — The system display (SD) shows the system page for the affected system. — The CLR pushbutton on the ECAM control panel lights up. In addition, a local warning light controlled directly by the affected system can light up. After completing remedial procedures, the flight crew must push the CLR pushbutton repeatedly until the displays return to their normal configurations : — MEMO messages on the E/WD — The system page related to the present flight phase on the SD. — The CLR light on the ECAM control panel turned off. sIMU_ F.P.S.3 UP for training only STD 13.1sinesron ECAM SEQUENCE Go INDICATING/RECORDING SYSTEMS | 1.31.25 P2 SEQ 005 | REV 30 EXAMPLE 1_- THE ECAM DETECTS NO FAILURE ah S co 96.0 —"?—_ 87.0 FULL 1900 — {3}, — 1500 . SEAT BELTS CTR TK FEEDG WING ALICE ENGINE FUSED vi (v1) 1530 "Ke —~ 1560 0.80.9 on vip «ve 11.5 — GF 11.5 7 a2T 13 AIR LDG ELEV AUTO SOOFT alec a cas W/S FI/N ealeie “ate cas ALD ET E 4150 5 Soc | 23ns6 —_— ee — NFe5-01-3125-002-A005A8 ECAM UPPER DISPLAY (E/WD) = ENGINE CONTROL PARAMETERS = FUEL QUANTITY INDICATION = FLAPS/SLATS POSITION MEMO INFORMATION ECAM LOWER DISPLAY (SD) = FLIGHT PHASE RELATED SYSTEM PAGE (CRUISE PAGE IN THIS EXAMPLE) = PERMANENT DATA, sIMU F. 3 UP for training only STD 13.1A320 FLIGHT CREW OPERATING MANUAL INDICATING/RECORDING SYSTEMS cnew or ECAM SEQUENCE 1.31.25 P3 SEQ 005 | REV 26 R 2- THE ECAM DETECTS A FAILURE For example, a hydraulic reservoir is overheating. COCKPIT INDICATIONS — A single chime sounds, — Both MASTER CAUTION lights come on and stay on. — A FAULT light on the overhead HYD panel comes on. — The memo space on the E/WD displays the message "HYD B RSVR OVHT" and the OFF”. instruction “BLUE ELEC PUMP... . — The lower ECAM display (SD) automatically calls up the diagram of the hydraulic systems and displays “OVHT” in amber by the blue system. R — The CLR pushbutton on the ECAM control panel lights up. NFC5~01-3125-003-A00544 ECAM UPPER DISPLAY (E/WD) = LEFT PART + INDEPENDENT FAILURE “TITLE OF THE FAILURE = ACTIONS TO BE PERFORMED - RIGHT PART MEMO INFORMATION ECAM LOWER DISPLAY (SD) ‘= SYNOPTIC OF THE AFFECTED SYSTEM AUTOMATICALLY CALLED OVHT IS DISPLAYED IN AMBER sIMU_ F.P.S.3 UP for training only STD 13.1@ 4320 INDICATING/RECORDING SYSTEMS | 1.31.25 P4 ECAM SEQUENCE SEQ 001 | REV 24 R 3 — THE FLIGHT CREW FOLLOWS THE INSTRUCTION DISPLAYED ON THE E/WD The crew switches off the blue ELEC pump, depressurizing the blue hydraulic circuit, COCKPIT INDICATIONS — A single chime sounds. — Both MASTER CAUTION lights stay on. — A FAULT/OFF light on the overhead panel comes on. — The second part of the message on the E/WD changes to “B SYS LO PR”. — The system diagram on the SD shows an amber zero for the pressure in the blue system, along with the amber “OVHT”. — The right side of the memo area indicates a secondary failure in the flight control system. — The CLR pushbutton on the ECAM control panel stays lighted. NFe5~01-3125-004-A001AA ECAM UPPER DISPLAY (E/WD) = LEFT PART INDEPENDENT FAILURE. AND PRIMARY FAILURE = RIGHT PART SECONDARY FAILURE ECAM LOWER DISPLAY (SD) SIMU F.P.S.3 UP for training only STD 13.1A320 FLIGHT CREW OPERATING MANUAL INDICATING/RECORDING SYSTEMS | 1.31.25 P5 cnew or ECAM SEQUENCE SEQ 005 | REV 30 4 - ONE OF THE PILOTS PUSHES THE CLR PUSHBUTTON ON THE ECP COCKPIT INDICATIONS — The CLR pushbutton remains lit. — The FAULT/OFF light stays on. — The hydraulic system messages disappear from the E/WD, and the right side of the memo area indicates a secondary failure in the flight control system. — The $D automatically calls up the flight control system page, with surface actuator indications associated with the blue hydraulic system shown in amber. ‘e (Ary (Bas om ex) (Gels 96.0 a7. 1900 —(,—~ 1500 ‘SEAT BELTS | Fler cay =) aE ee tf, prvex TRIM GZ 3.2 Cw» —] iy sey NFC5~01-3125-005-AD05AA ECAM UPPER DISPLAY (E/WD) = LEFT PART -MEMO INFORMATION ~ RIGHT PART «SECONDARY FAILURE ECAM LOWER DISPLAY (SD) = F/CTL SYSTEM PAGE AUTOMATICALLY DISPLAYED FAULTY SPOILERS (n°3) AND SURFACE ACTUATORS PRESSURE INDICATIONS B ARE DISPLAYED IN AMBER sIMU_ F.P.S.3 UP for training only STD 13.1Br INDICATING/RECORDING SYSTEMS | 1.31.25 P6 con ECAM SEQUENCE SEQ 005 | REV 30 5 - ONE OF THE PILOTS PUSHES THE CLR PUSHBUTTON A SECOND TIME COCKPIT INDICATIONS NFeS~01-3125-006-A0054A — The CLR and STS pushbuttons on the ECP light up. — The FAULT/OFF lights stay on. — The memo area on the E/WD returns to normal. — The STATUS page automatically appears on the SD, displaying the procedures for completing the flight with a faulty blue system. hy th (ea) (635) oe (a 96.0 —@— a7. Fee 1900-5, 1500 Ng 10 SEAT BELTS | ce 1K FEED STATUS no? sys cat 3 DUAL sue BEEC PUP SLATS stow ‘CAT 5 SINGLE ONLY ECAM UPPER DISPLAY (E/WD) = FULL MEMO DISPLAYED ECAM LOWER DISPLAY (SD) THE STATUS PAGE IS AUTOMATICALLY DISPLAYED TO: -PROVIDE THE PROCEDURE TO BE APPLIED FOR APPROACH. -PROVIDE LANDING DISTANCE FACTORS AND INFORMATION. LIST THE INOPERATIVE SYSTENS.. SIMU F.P.S.3 UP for training only STD 13.14320 INDICATING/RECORDING SYSTEMS | 1.31.25 ad a ECAM SEQUENCE SEQ 005 | REV 30 6 — ONE OF THE PILOTS PUSHES THE CLR PUSHBUTTON A THIRD TIME COCKPIT INDICATIONS — The CLR pushbutton light goes off. — The FAULT/OFF lights stay on. — A status reminder appears at the bottom of the E/WD. — The SD automatically calls up the system page for the flight phase. ECAM UPPER DISPLAY (E/WD) Ya) (PAG EC \ eo 96.0 27.0 1900 sf — 1500 SEAT BELTS cm XK Fens wine &1C 31s |< status REMINDER ECAN LOWER DISPLAY (SD) ENGINE FUSED vis «wo 1530. —"kg ~~ 1560 0.8 70.9 ~ RETURN TO THE FLIGHT PHASE on faeces RELATED SYSTEM PAGE : 1.5 — 11.5, ae (CRUISE PAGE AIR LOG ELEV AUTO SooFT 3 % x9. W/s FTA i ae Gia er 5 — 4150 STD 13.1 SIMU. F.P.S.3 UP for training onlyMPS 1300 INDICATING/RECORDING SYSTEMS | 1.31.27 P1 peer rem OEB REMINDER SEQ 100 | REV 33 GENERAL The OEB reminder function provides operational help to the crew by enabling them to clearly identify (on the ECAM) all procedures and status messages affected by an OEB. When a situation leading to a warning/caution occurs, a message informs the crew in real time that an OEB exists for the displayed warning and/or status and, consequently, that the procedure and/or status presented on the ECAM is not applicable. Then the crew must refer to the QRH where the correct information is provided. DESCRIPTION The OEB reminder flag may apply to the — ECAM procedure only, — ECAM procedure and corresponding status messages, ~ Status message only. PROCEDURE ONLY AFFECTED — The ECAM warning title remains unaltered, — All corresponding actions are suppressed and replaced by the “REFER TO QRH PROC” message, — The related status messages on the ECAM system display remains unaltered. COCKPIT INDICATION AIR PACK1 OVHT Et DI E, ee ee CAM UPPER DISPLAY (E/WD) STATUS JeWHEN PACK OVHT OUT: INOP SYS ~PACKI.. ee ONY nce ECAM LOWER DISPLAY (SD) NF.C5-C1-3127-001-A100AA sIMU_ F.P.S.3 UP for training only STD 13.1or INDICATING/RECORDING SYSTEMS | 1.31.27 P2 oer OEB REMINDER SEQ 100 | REV 33 PROCEDURE AND STATUS AFFECTED — The ECAM warming title remains unaltered, — All corresponding actions are suppressed and replaced by the “REFER TO QRH PROC” message, — The related status messages on the ECAM system display remains unchanged, except for the additional “REFER TO QRH PROC" title. COCKPIT INDICATION AIR PACK1 OVHT “REFER TO QRH PROC ‘STATUS WHEN PACK OVHT OUT: PACK1 PACK. NFCS~01-5127-002-A100AA REFER TO QRH PROC INOP SYS ECAM UPPER DISPLAY (E/WD) ECAM LOWER DISPLAY (SD) SIMU F.P.S.3 UP for training only STD 13.1A320 lone CaN ean arin MaMa OEB REMINDER SEQ 100 | REV 33 INDICATING/RECORDING SYSTEMS. 1.31.27 Es STATUS MESSAGE ONLY AFFECTED — The ECAM warning title remains unaltered, — The corresponding procedure remains unchanged, except for the additional “FOR STS REFER TO QRH" line. — The related status messages on the ECAM system display remains unchanged, except for the additional “REFER TO QRH PROC" title. COCKPIT INDICATION ‘AIR. PACK OVHT “PACK 1.200000 sOFF eWHEN PACK OVHT OUT: ECAM UPPER DISPLAY (E/WD) PACK, -0N “FOR STS REFER TO QRH| ‘STATUS REFER TO QRH PROC INOP SYS WHEN PACK OVHT OUT: PAA ECAM LOWER DISPLAY (SD) ~PACK1.. NFC5-01-3127-003-A 10008 sIMU_ F.P.S.3 UP for training only STD 13.1or INDICATING/RECORDING SYSTEMS oer OEB REMINDER 1.31.27 P4 SEQ 100 REV 33 OEB DATABASE The OEB database lists the warnings and cautions affected by an OEB. The OEB database can be : - Loaded manually on the aircraft via the MCDU, and stored in both FWCs. - Crossloaded from one FWC to the other FWC. - Updated by entering a code via the MCDU. + Checked via the MCDU. Note : The code provided on the OEB is designed to ensure that the OEB database is not updated before the OEB is available. sIMU_ F.P.S.3 UP for training only STD 13.1A320 INDICATING/RECORDING SYSTEMS. 1.31.30 Pal sm TOR ECAM CONTROLS SEQ 001 | REV 33 22 ECAM CONTROL PANEL NFC5-01-5130-001-A001AA ® OFF / BRT knobs Used to turn the ECAM DUs on and off, and to control their brightness (automatic adjustment of brightness for ambient light conditions is superimposed on this manual control). Note ; When the pilot turns the UPPER DISPLAY knob to OFF, the engine/warning (E/W) display appears on the lower display unit (automatic transfer). ©® System page pushbuttons — Call up the corresponding system pages on the SD. — Light up, when pushed for manual selection, or when an advisory is detected, — Call up the aircraft system page corresponding to the present flight phase or the current warning when pushed a second time. When only one ECAM display is on, the pilot can display a system page for up to 3 minutes by pushing and holding the system page pushbutton. If an advisory condition arises, the relevant system page is not automatically displayed, but the pushbutton light pulses. If an ECAM warning is triggered, the relevant system page is not automatically displayed, and the system page pushbutton does not light up. @® RCL pushbutton The pilot pushes the RCL pushbutton to call up the warning messages, the caution messages, and the status page, that may have been suppressed by the activation of the CLR pushbutton or by flight-phase-related inhibition. If there are no suppressed warnings or cautions, the E/WD shows "NORMAL" for five seconds. If the pilot holds this pushbutton down for more than three seconds, the E/WD displays any caution messages that were suppressed by the EMER CANC pushbutton. sIMU_ F.P.S.3 UP for training only STD 13.1OQ INDICATING/RECORDING SYSTEMS 1.31.30 P2 oer ECAM CONTROLS SEQ 002 | REV 33 @ STS (status) pushbutton The pilot pushes this pushbutton to display the STATUS page on the lower SD. The pushbutton remains lit, as long as the SD displays the STS page. If the system has no status messages, the status page displays “NORMAL” for five seconds. The pilot can clear the STATUS page by pushing the CLR pushbutton, or by pushing the STS pushbutton a second time. When only one ECAM display is on : — It displays the STATUS page only when the pilot pushes the STATUS pushbutton and holds it. He can display the next STATUS page, if any, by releasing the pushbutton and pushing it again (before two seconds have elapsed). The new page then appears after a short delay. — The pilot can keep the STS pushbutton pressed to display the STATUS page for a maximum of three minutes, after which the ECAM automatically displays the engineAwarning page. © CLR pushbutton This pushbutton remains lit as long as the E/WD is displaying a warning or caution message, or a status message on the SD. If itis lit, pressing it changes the ECAM display. © ALL pushbutton When this pushbutton is pressed and held down, the SD successively displays all the system pages at one-second intervals. If the ECAM control panel fails, the pilot can use this pushbutton to page through the system pages until he comes to the one he wants to look at. He then releases the pushbutton to select that page. SIMU F.P.S.3 UP for training only STD 13.1A320 INDICATING/RECORDING SYSTEMS. ECAM CONTROLS 1.31.30 Es SEQ 001 REV 32 @ EMER CANC pb This pushbutton affects the following — Warnings : - Cancel (stop) an aural warning for as long as the failure condition continues. Extinguishes the MASTER WARNINGS lights. Does not affect the ECAM message display. — Cautions : “Cancel any present caution (single chime, MASTER CAUTION lights, ECAM message) for the rest of the flight. Automatically calls up the STATUS page, which displays “CANCELLED CAUTION” and the title of the failure that is inhibited. The inhibition is automatically suppressed when Flight Phase 1 is initiated. The pilot may restore it manually by pressing the RECALL pushbutton for more than three seconds. ‘Note : This pushbutton should only be used to suppress spurious MASTER CAUTIONS. 1.0. CONFIG pb This pushbutton simulates the application of takeoff power. This is a test that triggers a warning, if the aircraft is not in takeoff configuration. (See 1.31.15). If the configuration is correct, the E/WD displays the "TO CONFIG NORMAL" message in the TO MEMO section Note: if the ECAM contro! panel fails, the CLR, RCL, STS, EMER CANC, and ALL pushbuttons remain operative, because their contacts are directly wired to the flight warning and display management computers. sIMU_ F.P.S.3 UP for training only STD 13.1