Scribd
Upload
41 views18 pages

NSUR2-1 Whispertek™ Surface Dual Installaton Guide: ™ Ideation System

The document provides instructions for installing two WhisperTek surfaces. It details measuring and marking the wall, aligning and adhering the first surface, then mounting the second surface by aligning it to the first and adhering it to the wall. The instructions are broken into four steps and include diagrams to illustrate each part of the process.

Uploaded by

Nureva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
41 views18 pages

NSUR2-1 Whispertek™ Surface Dual Installaton Guide: ™ Ideation System

The document provides instructions for installing two WhisperTek surfaces. It details measuring and marking the wall, aligning and adhering the first surface, then mounting the second surface by aligning it to the first and adhering it to the wall. The instructions are broken into four steps and include diagrams to illustrate each part of the process.

Uploaded by

Nureva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

Span ideation system

NSUR2-1 Whispertek surface


Dual installaton guide

TABLE OF CONTENTS
Before you begin

Step 1 Measure and mark

Step 2 Aligning surface 1

Step 3 Adhering surface 1

Step 4 Mounting surface 2

14

WHAT YOULL NEED

Measuring tape

Laser level

Two (2) people to


install the surface.

3" roller

BEFORE YOU BEGIN


TM

To avoid cracking, ensure your surfaces have reached


room temperature before removing from the boxes. Allow the
surfaceto rest and flatten for 2 to 3 hours before installation.

WhisperTek

Surface installation

http://nureva-span.uservoice.com/knowledgebase/articles/603927

70F

Nureva WhisperTek dual installation guide February 2016

21C

Pa g e 3

STEP 1

MEASURE AND MARK

Nureva WhisperTek dual installation guide February 2016

Pa g e 4

Measure and mark

Set up the laser lever and project a line 1" above the projected image.
Find the overall centerline of the system. Each surface is 124" (314 cm) long and should extend 1" past the projected
image. Once you have found the centerline, use a straight edge to mark the entire length of the centerline.

Nureva WhisperTek dual installation guide February 2016

Pa g e 7

STEP 2

A L I G N I N G S U R FA C E 1

Nureva WhisperTek dual installation guide February 2016

Pa g e 6

Peel the adhesive liner


Carefully flip one of the surfaces so the adhesive liner is facing up. Fold down a 6-inch wide horizontal strip
from the edge of the surface to where the liner is cut in the center. Fold down a corner of the liner
on the other side of the cut line.

Nureva WhisperTek dual installation guide February 2016

Pa g e 5

Align surface 1
Do not let the exposed adhesive touch the wall during this step.

Nureva WhisperTek dual installation guide February 2016

Pa g e 8

STEP 3

A D H E R I N G S U R FA C E 1

Nureva WhisperTek dual installation guide February 2016

Pa g e 9

Hold the surface in place

Adhere the top of the surface

Once the surface is aligned, person A holds the


surface firmly against the wall.

Person B presses the exposed adhesive


against the wall ensuring it is level
with the laser line then firmly smoothes
the top of the surface against the wall.

Nureva WhisperTek dual installation guide February 2016

Pa g e 1 0

Remove the adhesive liner


While person A holds their side of the surface, person B pulls the bottom of the surface away from
the wall to remove the release liner . Do not bendthe surface at a sharp angle as this can cause
kinking.

Nureva WhisperTek dual installation guide February 2016

Pa g e 1 1

Begin adhering the surface to the wall


Starting from the top of the surface and moving downward, person B begins to press the surface against the
wall with overlapping up-and-down strokes toprevent bubbles from forming under the surface.

Nureva WhisperTek dual installation guide February 2016

Pa g e 1 2

Adhere the second half of surface 1


Once the first half is adhered, person A pulls the surface away from the wall from the side carefully while avoiding
kinking the surface in the center. Person B goes behind the surface to remove the adhesive liner from the second half of
the surface.
Person A holds the outside edge of the surface while person B smoothes it against the wall using up-and-down stokes.

Nureva WhisperTek dual installation guide February 2016

CBA

Pa g e 1 3

STEP 4

M O U N T I N G S U R FA C E 2

Nureva WhisperTek dual installation guide February 2016

Pa g e 1 4

Peel the adhesive liner


Carefully flip the other surface so the adhesive liner is facing up. Fold down a 6-inch wide vertical strip on the side of
the surface that will touch the system centerline. Fold down the corner of the liner on the other side of the cut line.

N u reva W h i s p e rT e k d u a l i n sta l l at i o n g u i d e F e b r u a r y 2 0 1 6

Pa g e 1 5

Align and secure surface 2


Person A and person B hold the surface up to the wall. Person A aligns the center edge of the surface with the
surface that has already been installed. Once the center edge is completely aligned, person A smoothes down
the exposed adhesive to secure the edge of surface 2 against surface 1.

N u reva W h i s p e rT e k d u a l i n sta l l at i o n g u i d e F e b r u a r y 2 0 1 6

Pa g e 1 3

Person B walks the edge of the surface away from the wall so person A can get behind the surface to remove the liner
from where it was folded.

While person B holds the outside edge, person A goes back to the front of the surface and smoothes that half of the
surface against the wall starting at the centerline using overlapping up-and-down strokes.

Once person A adheres that side of the surface, person A then goes behind the surface again to remove the second
half of the liner to smooth that side of the surface against the wall.

Nureva WhisperTek dual installation guide February 2016

Pa g e 1 7

Roller both surfaces


Apply pressure to both the surfaces using the 3" roller to promote proper adhesion. The surface is now ready
for use.

2016 Nureva Inc. All rights reserved. Nureva, Span, WhisperTek and the Span logo are trademarks of Nureva Inc. in the United States, Canada and other countries.
Nureva WhisperTek dual installation guide February 2016

Pa g e 1 8

You might also like